A new and simple method for the determination of hydroxylamine in environmental water, such as fresh rivers and lakes using hypochlorite, followed by its gas choromatographic detection, has been developed. A glass vial filled with sample water was sealed by a butyl-rubber stopper and aluminum cap without head-space, and then sodium hypochlorite solution was injected into the vial through a syringe to convert hydroxylamine to nitrous oxide. The head-space in the glass vial was prepared with 99.9% grade N2 using a gas-tight syringe. After the glass vial was shaken for a few minutes, nitrous oxide in the gas-phase was measured by a gas chromatograph with an electron-capture detector. The dissolved nitrous oxide in the liquid-phase was calculated according to the solubility formula. The proposed method was applied to the analysis of fresh-water samples taken from Iu river and Hii river, flowing into brackish Lakes Nakaumi and Shinji, respectively. 相似文献
Summary Atomic fluorescence (AFS), absorption (AAS) and emission (AES) systems were evaluated for the determination of inorganic mercury. Identical vapour generation and amalgamation procedures were used to permit direct comparison of the performance of a commercial long-path AAS instrument to laboratory constructed non-dispersive AFS as well as He-MIP based AES instruments. Instrumental noise-limited detection limits (LOD) were 0.94, 2.4, 2.8 pg for AAS, AES and AFS techniques, respectively. Methodological LOD's were found to be blank controlled and similar for all three instruments, viz. 9, 25 and 16 pg for AAS, AFS and AES, respectively. All three systems produced accurate results at the low ng/l concentration, as verified by the analysis of a certified river water reference material (NRCC ORMS-1). 相似文献
A negative-ion-based neutral beam injector (N-NBI) has been constructed for JT-60U. The N-NBI is designed to inject 500 keV, 10 MW neutral beams using two ion sources, each producing a 500 keV, 22 A D− ion beam. In the preliminary experiment using one ion source, a D− ion beam of 13.5 A has been successfully accelerated with an energy of 400 keV (5.4 MW) for 0.12 s at an operating pressure of 0.22 Pa. This is the highest D− beam current and power in the world. Co-extracted electron current was effectively suppressed to the ratio of Ie/ID− < 1. The highest energy beam of 460 keV, 2.4 A, 0.44 s has also been obtained. To realize 1 MeV class NBI system for ITER (International Thermonuclear Experimental Reactor), demonstration of ampere class negative ion beam acceleration up to 1 MeV is an important mile stone. To achieve the mile stone, a prototype accelerator and a 1 MV, 1 A test facility called MeV Test Facility (MTF) were constructed. Up to now, an H− ion beam was accelerated up to the energy of 805 keV with an acceleration drain current of 150 mA for 1 s in a five stage electrostatic multi-aperture accelerator. 相似文献
The dry pulp direct kneading method is an industrially viable, low-energy process for manufacturing cellulose nanofiber (CNF)-reinforced polymer composites, where the chemically modified pulps are nanofibrillated and uniformly dispersed in the polymer matrix during melt compounding. In the present study, cellulose fibers of various sizes ranging from surface-fibrillated pulps (20 μm in width) to fine CNFs (20 nm in width) were prepared from softwood bleached kraft pulps using a refiner and a high-pressure homogenizer. These cellulose fibers were modified with alkenyl succinic anhydride and dried. The dried fibers were used as a feed material for melt compounding in the dry pulp direct kneading method to fabricate CNF-reinforced high-density polyethylene (HDPE). When surface-fibrillated pulps were employed as a feed material, the pulps were nanofibrillated and dispersed uniformly in the HDPE matrix during melt compounding. The resulting composites had much better properties—i.e., much higher tensile modulus and strength values, and much lower coefficient of thermal expansion values—than the composites produced using pulps without pre-fibrillation. However, when CNFs were used as a feed material, they were shortened and agglomerated during melt compounding, and the properties of the composites consequently deteriorated. The study concludes that surface-fibrillated pulp, which can be produced cost-effectively using a refiner on an industrial scale, is more suitable as a feed material than CNFs for melt compounding in the dry pulp direct kneading method. This finding enables the elimination of a preliminary step in the preparation of CNFs from pulps, which is a time-consuming and energy-intensive process.
Copolymerizations of N-vinylcarbazole with both isobutyl vinyl ether and N-vinyl-pyrrolidone initiated by some organic electron acceptors have been investigated for the purpose of elucidating the propagation mechanism in the charge-transfer polymerization. Copolymerizations of the same system catalyzed by authentic cationic catalysts have also been made for comparison. The results indicate that the propagation mechanism of the charge-transfer polymerization studied is catio ie. 相似文献
The strength distributions of the giant monopole resonance (GMR) have been measured in the even-A Sn isotopes (A=112-124) with inelastic scattering of 400-MeV alpha particles in the angular range 0 degrees -8.5 degrees . We find that the experimentally observed GMR energies of the Sn isotopes are lower than the values predicted by theoretical calculations that reproduce the GMR energies in 208Pb and 90Zr very well. From the GMR data, a value of Ktau = -550 +/- 100 MeV is obtained for the asymmetry term in the nuclear incompressibility. 相似文献