Bei der Zuckerbestimmung

Ohne Zusammenfassung     

Novel dinitroxide mediating agent for stable free‐radical polymerization

A novel dinitroxide mediating agent that was suitable for stable free‐radical polymerization was synthesized and used in the block copolymerization of styrene and t‐butyl styrene. Quantitative yields of a novel dinitroxide based on 1,6‐hexamethylene diisocyanate and 4‐hydroxy‐2,2,6,6‐tetramethyl‐1‐piperidinyloxy were obtained. Various experimental parameters, including the nitroxide‐to‐initiator molar ratio, were examined, and it was determined that the polymerization was most controlled under conditions similar to those of conventional 2,2,6,6‐tetramethyl‐1‐piperidinyloxy‐mediated stable free‐radical polymerization. Moreover, the dinitroxide mediator proved to be a viable route for the facile two‐step synthesis of triblock copolymers of styrene and t‐butyl styrene. However, the dinitroxide mediation process resulted in a higher than expected level of nitroxide decomposition, which resulted in polymers possessing a terminal alkoxyamine and an adjacent hydroxylamine rather than a preferred internal bisalkoxyamine. This decomposition resulted in the formation of diblock copolymer species during the triblock copolymer synthesis. Gel permeation chromatography was used to monitor the chain‐end decomposition kinetics, and the determined observed rate constant (5.89 × 10^?5 s^?1) for decomposition agreed well with previous studies for other dinitroxide mediating agents. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 1547–1556, 2004     

Standardization of Methods for Characterizing the Surface Geometry of Solids

Since a comprehensive survey published in 1999 [1] much work was done in standardizing measuring methods to characterize the surface geometry of dispersed and/or porous solids and to certify reference materials. The present paper is an extension of a short communication [2]. It gives a survey on existing standards and reports on new drafts and proposals.     

Raman spectroscopy of carbon fibres

Investigations of coated carbon fibres are reported using Raman spectroscopy. Relationships between different process parameters (for example precursor concentration, reactor temperature and various precursors) and the resulting types of carbon fibres are discussed.     

HPLC with amperometric detection for the determination of pesticides of high polarity

A relatively simple procedure is described for the selective and highly sensitive determination of amitrole (3-amino-1,2,4-triazole) by ionpair HPLC with amperometric detection. The separation was achieved on a polar CN-column using hexane, propanol, water (62:36:2) with LiClO₄ (2.5 g·l^–1) and trichloroacetic acid (2 g·l^–1) as electrolytes. The determination range lies between 500 pg and 500 ng and the limit of detection was found to be 200 pg (s.d.: 11%; N=9). The minimum detectability for the alternative UV-monitoring was 2.5 ng. The developed method may be helpful in production and quality control and for the selective determination of amitrole in commercial formulations.     

Properties of polystyrene-poly(methylmethacrylate) random and diblock copolymers in dilute and semidilute solutions

Solution properties for random and diblock copolymers of polystyrene (PS) and poly(methyl methacrylate) (PMMA) have been measured by dynamic and total intensity light scattering in solvents of differing quality. The results are compared with the corresponding properties for PS and PMMA homopolymers of similar molecular weight, in order to determine if interactions between unlike monomers are significant. The hydrodynamic radius (R_h) and diffusion second virial coefficient (k_d) for the random copolymer are found to be larger than the corresponding values for the homopolymers in a solvent which is near-theta for the two homopolymers, whereas no such effect is observed for the block copolymer. This suggests that most intrachain interactions occur a relatively short distance along the chain backbone. In a mutual good solvent R_h and k_d of the random copolymer are comparable to the average of the values for the homopolymers, indicating that in a good solvent monomer/solvent interactions dominate over monomer/monomer interactions. For an isolated diblock copolymer in a mutual good solvent, there is no evidence that interactions between unlike monomers lead to additional expansion of the entire molecule, as measured by R_h, nor expansion of the individual blocks as probed by light scattering with one block optically masked. However, at low but finite concentration there is evidence (the coefficients of the binary interaction terms in the viscosity and the mutual diffusion coefficient, and the second and third virial coefficients) that a weak ordering effect may exist in block copolymer solutions, far from the conditions where microphase separation occurs. Finally, measurements of ternary polymer-polymer-solvent solutions show no dependence on monomer composition or monomer distribution for the tracer diffusion of probe PS-PMMA copolymers in a PMMA/toluene matrix. This indicate that the frictional interaction is largely unaffected by interactions between unlike monomers. However, there is evidence that the thermodynamic interaction is more unfavorable between a random copolymer and the homopolymer matrix than between a diblock and the matrix. © 1994 John Wiley & Sons, Inc.     

Domain size equilibration in sphere‐forming block copolymers

The kinetics of domain size equilibration were studied for asymmetric poly(ethylene‐alt‐propylene)‐b‐poly(dimethyl siloxane) (EPDMS) and polyisoprene‐b‐poly(dimethyl siloxane) (IDMS) block copolymers in the body‐centered cubic ordered phase. Small‐angle X‐ray scattering measurements of the principal peak position (q*) were made as a function of time after temperature jumps within the ordered state. The equilibration times were remarkably long, especially on cooling and for temperatures below 100 °C. For example, after a quench to 40 °C, q* for EPDMS had not fully equilibrated even after several weeks of annealing; IDMS required several days to equilibrate at the same temperature. In contrast, a lamella‐forming EPDMS sample was able to adjust q* within the timescale of the measurements (i.e., minutes) with both heating and cooling over the same temperature range. Measurements of tracer diffusion indicated that chain mobility was not the rate‐limiting step, although differences in mobility did account for the differences between EPDMS and IDMS. Rather, the limiting step was the required reduction in the number density of spheres on cooling; the disappearance of spheres, either by evaporation or by fusion, provided a large kinetic barrier. Lamellae, however, could adjust domain dimensions simply by local displacements of individual chains. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 715–724, 2003     

Complex polymer architectures through dimethoxymethyl 1,1‐diphenylethylene derivatives

The reactions of polystyryllithium and potassium on dimethoxymethyl 1,1‐diphenylethylene derivatives were studied in different solvents. In a polar medium, A₃ and A₆ star types were formed according to the stoichiometry, whereas in a nonpolar medium, hyperbranched structures were synthesized. Extensions of an already proposed mechanism in polar and nonpolar media were examined. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 3329–3335, 2003     

Postmodification of poly(9‐alkyl‐9H‐carbazole‐2,7‐diyl)s as a route to new main‐chain‐functionalized carbazole polymers

The postmodification of poly[9‐(2‐hexyldecyl)‐9H‐carbazole‐2,7‐diyl] ( P1 ) upon its reaction with N‐bromosuccinimide affords exclusive and full bromination of the 3,6‐positions of the carbazole repeat units to yield poly[3,6‐dibromo‐9‐(2‐hexyldecyl)‐9H‐carbazole‐2,7‐diyl] ( P2 ). Brominated polymer P2 can be used as a precursor for further functionalization at the 3,6‐positions with the desired functional group to afford other useful polymers. Polymer P2 has hence been reacted with copper(I) cyanide to afford poly[3,6‐dicyano‐9‐(2‐hexyldecyl)‐9H‐carbazole‐2,7‐diyl] ( P3 ). Full substitution of the bromide groups with nitrile‐functional groups has been achieved. The preparation and structural characterization of polymers P2 and P3 are presented together with studies on their electronic conjugation and photoluminescence properties. Cyclic voltammetry studies on polymer P3 indicate that the new polymer is easier to reduce (n‐dope) but more difficult to oxidize than its unsubstituted counterpart ( P1 ) as a result of the introduction of the electron‐withdrawing nitrile‐functional groups at the 3,6‐positions on the carbazole repeat units on the polymer chains. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 3336–3342, 2006