Improved detectability with a polymer-based trapping device in rapid HPLC analysis for ultra-low levels of bisphenol A (BPA) in environmental samples.

A new high-performance liquid chromatography (HPLC) method has been developed to detect ultra-low concentrations of bisphenol-A (BPA) (below 1 ng/L (ppt)) using column switching electrochemical detection (ECD). The results were superior to those obtained from manual pretreatment procedure with membrane stationary phase. BPA is inherently ubiquitous in the environment, including tools and solvents used for its analysis; to obtain meaningful results, therefore, the concentration of the overall BPA contamination must be below the detection limit for BPA using the analytical system. Therefore, purified water for preparing the standard BPA solution must be filtered with a hydrophobic membrane to suppress BPA background levels of contamination. In addition, we investigated methods for effectively preserving environmental water containing BPA. The addition of a small amount of ethylenediaminetetraacetic acid (EDTA) provided good recovery even after overnight storage. By employing these precautionary measures and procedures to reduce BPA contamination from the analytical procedure, we could accurately determine l(-10) ppt of BPA in environmental water samples using a column switching HPLC system.     

Development and features of hydro-membrane gas chromatography.

Hydro-membrane gas chromatography (HMGC) is achieved by the annular condensation of water in a capillary column at less than 70 degrees C. The annular membrane of water is formed as a result of the wettability of the stationary phase, which is induced at a water contact angle ranging from 75 degrees to 79 degrees, as derived from a solubility parameter (delta) range of 15.7 +/- 0.3 MPa(1/2) of the coated resin. The range of the liquid to gas volume ratio (beta) required to support the annular membrane should be kept between 0.00005 and 0.0003. In the case of a 0.25-mm i.d. column, the ratio can be set by the combination of a 0.1 to 0.2 microl min(-1) water supply rate and helium gas flow rate. Separation by HMGC develops not only a gas-solid partition but also a focusing effect on the water membrane. One feature of HMGC is that it gives a non-adsorption chromatogram based on the blocking effect of pre-adsorbed water; furthermore, despite the presence of a relatively large quantity of water, the electron impact ionization efficiency is kept the same as in the usual GC/MS condition. The detection limit with the injection of 1 microl of aquatic solution was estimated to be less than 0.1 ppb of low-molecular-weight fatty acids with s/n = 5 on a mass chromatogram at m/z 45. The HMGC/EI-MS system can be applied to the trace analysis of C1 to C3 volatile acids, volatile inorganic acids, and halogenated organic acids in water.     

Basic study of the gelation of dimethacrylate‐type crosslinking agents

An investigation was made of the gelation of dimethacrylate‐type crosslinking agents in view of an application for separation media. The study mainly centered on a crosslinking agent, glycerol dimethacrylate (GDMA), which is relatively hydrophilic because of a hydroxyl group in the middle of its structure. The gelation of GDMA was compared with that of other hydrophobic crosslinking agents such as ethylene glycol dimethacrylate and 1,6‐hexanediol dimethacrylate. The diluents used in the study were toluene, toluene with methanol, and cyclohexanol. The gelation was observed in real time with a charge coupled device camera and dynamic light scattering (DLS). Also, the separated dry gels were extensively characterized with scanning electron microscopy, BET (N₂ absorption and desorption isotherm), and Fourier transform infrared. DLS analysis showed a stronger molecular interaction of GDMA gelation in toluene, whereas this interaction was much weaker in an alcoholic solvent such as toluene with methanol or cyclohexanol. This indicated that GDMA gelation might proceed through hydrogen bonding as well as a crosslinking reaction of vinyl groups. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 949–958, 2006