Facile one‐pot method of initiator fixation for surface‐initiated atom transfer radical polymerization on carbon hard spheres

An efficient and novel one‐pot process is developed to immobilize the atom transfer radical polymerization (ATRP) initiators onto the surface of fully pyrolyzed carbon hard spheres (CHSs) via a radical trapping process from the in situ thermal decomposition of bis(bromomethylbenzoyl)peroxide. The CHSs do not require any additional preparative treatment prior to the initiator immobilization. Styrene and methyl methacrylate are polymerized onto initiator‐immobilized CHSs by surface‐initiated atomic transfer radical polymerization (SI‐ATRP). Samples are characterized using Fourier transform infrared, thermogravimetric analysis, scanning electron microscopy, and transmission electron microscopy. These methods of characterization confirmed that all the CHSs are coated with a uniform layer of grafted polymer. This efficient, one‐pot immobilization of ATRP‐initiators represents an exceptionally simple route for the rapid preparation of various polymer‐coated carbon‐based nanomaterials using SI‐ATRP. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013, 51, 3314–3322     

Structural,dielectric and optical properties of sol–gel synthesized 0.55Ba(Zr0.2Ti0.8)O3–0.45(Ba0.7Ca0.3)TiO3 ceramic

Lead-free polycrystalline ceramic 0.55Ba(Zr_0.2Ti_0.8)O₃–0.45(Ba_0.7Ca_0.3)TiO₃ (0.55BZT–0.45BCT) was synthesized by sol–gel method and the dielectric, impedance and optical properties of this ceramic were studied. X-ray diffraction analysis revealed the formation of pure perovskite phase with the coexistence of tetragonal and rhombohedral structures. The high value of dielectric constant (~6,985) with low dielectric loss (~0.013) was obtained at room temperature. Bulk and grain boundary resistances were measured by impedance analysis, which revealed negative temperature coefficient of resistance behaviour in this ceramic. The estimated value of optical band gap was found to be ~3.16 eV, which is related to the presence of intermediate energy levels. Two emission bands one at ~365 nm (UV region) and another at ~465 nm (blue region) were observed in photoluminescence spectrum at room temperature.     

Dielectric, thermal and optical study of an unusually shaped liquid crystal

Dielectric measurements have been carried out for the determination of real and imaginary parts of the permittivity of a newly synthesized, unusually shaped liquid crystal. The sample has been investigated in the frequency range from 100 Hz to 10 MHz within a temperature range 80-130 °C. The dielectric measurements in the smectic A phase indicate a Cole-Cole type of dispersion, and the activation energy was found to be 5.5 meV by using the Arrhenius plot of relaxation time. In addition to this, thermal and optical transmittance studies have also been conducted in the above mentioned temperature range, and the temperature dependence of these parameters has been discussed in detail. The phase transition temperature obtained from a differential scanning calorimetry (DSC) study matches within 2 °C that was obtained from an optical transmittance study. The dielectric and optical behavior of the unusually shaped liquid crystal has been explained on the basis of a proposed theoretical model in which a sample possesses two different conformers having induced polarizations in opposite directions.     

Thermal neutron polarisation

The basic principle for the production of polarised thermal neutrons is discussed and the choice of various crystal monochromators surveyed. Brief mention of broad-spectrum polarisers is made. The application of polarised neutrons to the study of magnetisation density distributions in magnetic crystals, the dynamic concept of polarisation, principle and use of polarisation analysis, the neutron spin-echo technique are discussed.     

A polarised neutron study of magnetic moment density in Cu2MnAl

A polarised neutron study of the ferromagnetic Heusler alloy Cu₂Mn_0.863Al_1.057 has been made. It has been concluded that the magnetic moment density is primarily situated on the Mn ions. On assigning the Mn-moment value, the observed magnetic form factor is found to be in good agreement with the Mn²⁺ free ion form factor calculated by Watson and Freeman. A slight asphericity has been observed in the moment density. It is estimated that there are about 3% excess 3d-electrons in the Eg states compared to spherical distribution. There is evidence of a very small positive polarisation of the Cu atoms. No appreciable conduction electron polarisation is found.     

Effect of contact angle on the morphology of nanostructures produced by solution wetting of anodized aluminum oxide templates

Template-assisted nanofabrication is a simple and effective method to produce various nanostructure morphologies by controlling the polymer, solvent, and template characteristics. In this study, the importance of the surface interactions between the solution and the template in controlling the morphology of the nanostructures has been highlighted. Contact angles between various polymer solutions and anodized aluminum oxide (AAO) templates have been determined. The morphology of the resultant nanostructures has been correlated with the measured contact angles between solution and template. It is generally observed that nanorods (diameter of 100–350 nm) are produced at low contact angles, whereas nanotubes (diameter of 200–400 nm) tend to form at high contact angles. Therefore, desired nanostructure morphology for a given application can be obtained by controlling the initial wetting interaction between solution and template.     

Magnetic properties of carbon nanosheets

Two-dimensional carbon nanosheets have been fabricated using inductively coupled radio frequency plasma-enhanced chemical vapour deposition. The structural properties of the nanosheets have been characterised using atomic force microscopy, scanning electron microscopy and X-ray diffractometer. The magnetisation of the samples was studied using vibrating sample magnetometer. The magnetisation of the nanosheets was found to be diamagnetic for fast synthesis processes (30 and 60 min). On the other hand, the nanosheets exhibited a weak ferromagnetic response for the slow (120 min) synthesis process. Energy dispersive spectrometry and atomic absorption spectroscopy confirmed that the magnetisation exhibited by the carbon nanosheets was an intrinsic property and that it was not due to contamination from the substrate. Raman spectroscopy studies revealed that the ferromagnetic carbon nanosheets have a higher ratio (1.20) of graphite peak (I _G) to disordered peak (I _D) than normally expected (0.75–0.90). Available data indicated that the magnetisation was due to the presence of structural disorders.     

Recent radiochemical studies of the fission process

This article summarizes the recent radiochemical investigations on mass, charge kinetic energy and fragment angular distributions in low energy fission of actinides.     

Higher Order Nonlinear Effect and Limitation of Soliton Propagation in Dispersive-Nonlinear Medium for Dispersion-Shifted Fiber

A computer simulation of the nonlinear Schrödinger equation is carried out to evaluate the impact of nonlinear susceptibility of a single mode fiber on the transmission of a soliton pulse. The third and fifth order nonlinear susceptibilities are considered in the simulation. The results show that the output soliton pulse shape strongly depends on the third order nonlinear susceptibility and gets distorted when the full width half maximum (FWHM) pulse width is of the order of 10ps or less.