Power scaling of printed-circuit-board preionized TEA CO2 laser up to 3.6 kW

A high average power, high-repetition-rate TEA CO₂ laser employing printed-circuit-board preionizer is described. The power scaling of this preionization configuration has been demonstrated. The average output power reaches 3.6 kW at pulse repetition rate of 180 pps. Furthermore, the scaling-up ability of the rotating spark gap as high-voltage switch for high-average-power gas laser has been validated.     

一维接触过程的光滑性与稳定性

本文证明了一维接触过程在适当的小扰动下，其极点平稳分布除在临界点λ＿ｃ处外总是光滑的．特别，一维接触过程本身的极点平稳分布关于其参数除在临界点处外总是光滑的．     

Exponential convergence for one dimensional contact processes

The complete convergence theorem implies that starting from any initial distribution the one dimensional contact process converges to a limit ast. In this paper we give a necessary and sufficient condition on the initial distribution for the convergence to occur with exponential rapidity.This work was discussed while the authors were visiting the Nankai Mathematics Institute in Tianjin.Partially supported by the National Science Foundation, the Army Research Office through the Mathematical Sciences Institute at Cornell University, and a Guggenheim fellowship.Research supported by the National Science Foundation of China.     

A Hybrid Assembly of MXene with NH2−Si Nanoparticles Boosting Lithium Storage Performance

A facile hybrid assembly between Ti₃C₂T_x MXene nanosheets and (3‐aminopropyl) triethoxylsilane‐modified Si nanoparticles (NH₂?Si NPs) was developed to construct multilayer stacking of Ti₃C₂T_x nanosheets with NH₂?Si NPs assembling together (NH₂?Si/Ti₃C₂T_x). NH₂?Si/Ti₃C₂T_x exhibits a significantly enhanced lithium storage performance compared to pristine Si, which is attributed to the robust crosslinking architecture and considerably improved electrical conductivity as well as shorter Li⁺ diffusion pathways. The optimized NH₂?Si/Ti₃C₂T_x anode with Ti₃C₂T_x: NH₂?Si mass ratio of 4 : 1 displays an enhanced capacity (864 mAh g^?1 at 0.1 C) with robust capacity retention, which is significantly higher than those of NH₂?Si NPs and Ti₃C₂T_x anodes. Furthermore, this work demonstrates the important effect of the MXene‐based electrode architecture on the electrochemical performance and can guide future work on designing high‐performance Si/MXene hybrids for energy storage applications.     

阳离子交换皂石黏土在基质辅助激光解吸电离飞行时间质谱分析中的应用

将一种人工合成的无机聚合物——蒙脱石皂石黏土（smectite,Sm）应用于基质辅助激光解吸电离飞行时间质谱分析（matrix-assisted laser desorption/ionization time of flight mass spectrometry, MALDI-TOF-MS）,以检测糖类化合物。 将传统的有机基质2,4,6-三羟基苯乙酮（trihydroxyacetophenone, THAP）与阳离子交换后的皂石黏土混合制备成新型复合基质,应用于糖类化合物的检测。通过比较不同的制样方法,测定不同分子直径的糖类化合物,发现由于受复合基质晶面间距的限制,只有小分子糖类化合物能进入晶面间隙充分接触有机基质并被离子化,从而实现对小分子糖类化合物的选择性检测。     

Sm2Fe17合金的氢化-歧化过程演化

通过X射线衍射(XRD)、扫描电镜(SEM)和能谱分析(EDX)等手段重点研究了Sm2Fe17合金在氢化-歧化过程中的相组成、相的变化以及微观结构的演化规律。研究表明：在0．1MPa的H2气氛下，Sm2Fe17合金首先吸氢；400℃时合金出现部分脱氢现象；在T≥500℃逐渐开始歧化为SmHx和α—Fe，同时生成了大量的微晶或非晶组织；随着温度的升高，合金中的微晶非晶逐渐晶化，750℃时晶化完全，晶粒长大至20～100nm。通过对Sm2Fe17合金的氢化一歧化过程研究，建立了该过程的微观结构变化规律的物理模型。     

激光打靶过程中的电磁脉冲特性

为诊断激光打靶产生的电磁脉冲信号分布,选取环天线作为主要电磁脉冲信号采集装置,对靶室内外信号同时进行测试。从天线设计制作到天线标定,描述了脉冲诊断系统的搭建。通过对信号进行采集及处理,对比分析了靶室外、法兰口及靶室内脉冲信号的频域特性和强度。得出靶室内受到电磁脉冲辐射强度最大且频谱分布最广,其次是法兰口,靶室外电磁脉冲信号最弱。总结多次激光打靶电磁脉冲信号频域分布,可看出波峰主要出现在0.5,1.2,3 GHz。电磁脉冲时域结果规律性展示出脉冲持续约100 ns,因靶室内回波振荡,电磁脉冲信号于几ns处及几十ns处有较明显峰值蔟。     

Germanium Quantum Dots Embedded in N‐Doping Graphene Matrix with Sponge‐Like Architecture for Enhanced Performance in Lithium‐Ion Batteries

Germanium quantum dots embedded in a nitrogen‐doped graphene matrix with a sponge‐like architecture (Ge/GN sponge) are prepared through a simple and scalable synthetic method, involving freeze drying to obtain the Ge(OH)₄/graphene oxide (GO) precursor and subsequent heat reduction treatment. Upon application as an anode for the lithium‐ion battery (LIB), the Ge/GN sponge exhibits a high discharge capacity compared with previously reported N‐doped graphene. The electrode with the as‐synthesized Ge/GN sponge can deliver a capacity of 1258 mAh g^?1 even after 50 charge/discharge cycles. This improved electrochemical performance can be attributed to the pore memory effect and highly conductive N‐doping GN matrix from the unique sponge‐like structure.     

菠萝蛋白酶催化合成寡聚L-酪氨酸

以菠萝蛋白酶为催化剂从L-酪氨酸甲酯聚合得到寡聚L-酪氨酸(O-L-Try)。 以0.8 U/mL蛋白酶在体积分数为7.5%的二甲亚砜(DMSO)缓冲液(pH=7.5,0.2 mol/L)中催化0.23 g/mL L-酪氨酸甲酯在50 ℃下聚合反应5 h后,O-L-Try产率达到65%。 通过基质辅助激光解吸电离飞行时间质谱(MALDI-TOF-MS)、氢核磁共振波谱仪(¹H NMR)、拉曼光谱、傅里叶变换红外光谱仪(FTIR)等技术手段表征了O-L-Try结构和性能特征。 结果表明,MALDI-TOF-MS测定的O-L-Try的聚合度主要为10。 ¹H NMR谱图分析得到的O-L-Try的平均聚合度为8。 拉曼光谱显示,O-L-Try的肽键特征峰位于1623 cm^-1(酰胺Ⅰ带)、1447 cm^-1(酰胺Ⅱ带)、1270 cm^-1(酰胺Ⅲ带)和648 cm^-1(酰胺Ⅳ带)。     

舷侧水对船舶抗碰撞性能的影响

为了评估舷侧液舱在大型撞击物下的抗碰撞特性,采用有限元法和简化理论法对典型球鼻艏在不同撞击速度和液舱水线工况下的舷侧外板和内板的抗破坏性能进行了分析。结果表明:舷侧水效应可以显著提升双舷侧结构的抗破坏性能,但是提升的幅度是有限的,而且水效应对外板的破坏作用力影响较小,对舷侧内板的破坏作用力影响较大;当球鼻艏撞击速度逐渐增高时,舷侧外板和内板的破坏作用力也逐渐增大,但增大速率逐渐降低,其中舷侧外板较舷侧内板的增大速率更快趋于平缓。对不同液舱水线的分析表明:舷侧液舱水线在受撞击的强框架以上时,对抗碰撞性能影响较小;当舷侧液舱水线在受撞击的强框架以下时,对舷侧外板的抗碰撞特性影响较小,但对舷侧内板的抗碰撞特性影响很大,并且随着球鼻艏碰撞速度的增高,不同水线位置对船舶抗碰撞性能的影响也随之增大。