Rheological and physical properties of aliphatic hyperbranched polyesters

The effects of the size (pseudo‐generation number) and nature of end groups on physical and rheological properties were investigated for a series of hyperbranched polyesters based on an ethoxylated pentaerythritol core and 2,2‐bis‐(hydroxymethyl)propionic acid repeat units. The observed linear dependence of the melt viscosity on the molar mass in the high pseudo‐generation‐number limit indicated that entanglement effects were substantially absent. Moreover, the marked influence of end capping of the end groups on the physical and rheological properties suggested that intermolecular interactions were dominated by contacts between the outer shells of the molecules, in which the end groups were assumed to be concentrated. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 1218–1225, 2004     

Relevance of Reflection in Static and Dynamic Light Scattering Experiments

Using a monodisperse PMMA dispersion, it was shown that light reflection at the sample cuvette walls may greatly influence the results of both static (SLS) and dynamic (DLS) light scattering experiments. Considering SLS, this reflection phenomenon mostly causes an overestimation of the scattered intensity at high scattering angles, which may give rise to the emergence of an additional, artificial peak in the lower region of the particle size distribution. On the other hand, the influcence of reflection on DLS measurements was shown to be particularly important in the upper region of the particle size distribution. The experimentally observed phenomena were explained from the basic principles of both particle sizing methods. Finally, it was shown that the disturbing effect of reflection could be avoided by modifying either the hardware or the software of the static and dynamic light scattering technique.     

A Ramsey‐type result for the hypercube

We prove that for every fixed k and ? ≥ 5 and for sufficiently large n, every edge coloring of the hypercube Q_n with k colors contains a monochromatic cycle of length 2 ?. This answers an open question of Chung. Our techniques provide also a characterization of all subgraphs H of the hypercube which are Ramsey, that is, have the property that for every k, any k‐edge coloring of a sufficiently large Q_n contains a monochromatic copy of H. © 2006 Wiley Periodicals, Inc. J Graph Theory 53: 196–208, 2006     

Influence of heat treatment conditions on the porosity changes of sulfonated styrene/divinylbenzene copolymers

Sulfonic cation exchangers with two ion exchange group concentrations (0.5 and 2.4 mmol/g, samples A and B, respectively) were obtained by sulfonation of a porous styrene (S) and divinylbenzene (DVB) copolymer with chlorosulfonic acid. Strong thermal decomposition of the sulfonated copolymer A, accompanied by significant changes in its porous structure, starts at ca. 400°C. The char has no sulfonic groups. After heat treatment at 400°C in steam, a sorbent was obtained (yield 65%) that shows higher phenol sorption than the untreated sample when related to the bed volume. The chlorosulfonic derivatives of the initial copolymer were less thermally resistant than the sulfonic ones obtained by hydrolysis. Pyrolysis of the cation exchanger B, in its H+ and Ca²⁺ forms, was carried out at 900°C (yield of both chars close to 30%). By subsequent steam activation at 800°C to a 50% burn-off of the char, sorbents with well-developed, but distinctly different, porous structures were obtained. The activated char from the sulfonated copolymer in its hydrogen form was highly microporous and indicated an effective surface area of 1180 m²/g. However, because of a low contribution of mesopores, its ability to adsorb phenol from the liquid phase was not very high. The activated char from the calcium-doped copolymer, indicating a smaller surface area (580 m²/g) but characterized by a well-developed mesoporosity, was a better sorbent for phenol. © 1994 John Wiley & Sons, Inc.     

Hydrophilic segmented block copolymers based on poly(ethylene oxide) and monodisperse amide segments

Segmented block copolymers based on poly(ethylene oxide) (PEO) flexible segments and monodisperse crystallizable bisester tetra‐amide segments were made via a polycondensation reaction. The molecular weight of the PEO segments varied from 600 to 4600 g/mol and a bisester tetra‐amide segment (T6T6T) based on dimethyl terephthalate (T) and hexamethylenediamine (6) was used. The resulting copolymers were melt‐processable and transparent. The crystallinity of the copolymers was investigated by differential scanning calorimetry (DSC) and Fourier Transform infrared (FTIR). The thermal properties were studied by DSC, temperature modulated synchrotron small angle X‐ray scattering (SAXS), and dynamic mechanical analysis (DMA). The elastic properties were evaluated by compression set (CS) test. The crystallinity of the T6T6T segments in the copolymers was high (>84%) and the crystallization fast due to the use of monodisperse tetra‐amide segments. DMA experiments showed that the materials had a low T_g, a broad and almost temperature independent rubbery plateau and a sharp flow temperature. With increasing PEO length both the PEO melting temperature and the PEO crystallinity increased. When the PEO segment length was longer than 2000 g/mol the PEO melting temperature was above room temperature and this resulted in a higher modulus and in higher compression set values at room temperature. The properties of PEO‐T6T6T copolymers were compared with similar poly(propylene oxide) and poly(tetramethylene oxide) copolymers. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 4522–4535, 2007     

Fluid-fluid phase separation in colloid-polymer mixtures studied with small angle light scattering and light microscopy

Mixtures of colloidal silica spheres and polydimethylsiloxane in cyclohexane with a colloid-polymer size ratio of about one were found to phase separate into two fluid phases, one which is colloid-rich and one which is colloid-poor. In this work the phase separation kinetics of this fluid-fluid phase separation is studied for different compositions of the colloid-polymer mixtures, and at several degrees of supersaturation, with small angle light scattering and with light microscopy. The small angle light scattering curve exhibits a peak that grows in intensity and that shifts to smaller wave vector with time. The characteristic length scale that is obtained from the scattering peak is of the order of a few μm, in agreement with observations by light microscopy. The domain size increases with time as , which might be an indication of coarsening by diffusion and coalescence, like in the case of binary liquid mixtures and polymer blends. For sufficiently low degrees of supersaturation the angular scattering intensity curves satisfy dynamical scaling behavior.     

Interpolation by a Game

We introduce a notion of a real game (a generalisation of the Karchmer-Wigderson game (cf. [3]) and of real communication complexity, and relate this complexity to the size of monotone real formulas and circuits. We give an exponential lower bound for tree-like monotone protocols (defined in [4, Definition 2.2]) of small real communication complexity solving the monotone communication complexity problem associated with the bipartite perfect matching problem. This work is motivated by a research in interpolation theorems for prepositional logic (by a problem posed in [5, Section 8], in particular). Our main objective is to extend the communication complexity approach of [4, 5] to a wider class of proof systems. In this direction we obtain an effective interpolation in a form of a protocol of small real communication complexity. Together with the above mentioned lower bound for tree-like protocols this yields as a corollary a lower bound on the number of steps for particular semantic derivations of Hall's theorem (these include tree-like cutting planes proofs for which an exponential lower bound was demonstrated in [2]).     

Aluminum(III) complexes containing O,O chelating ligand

The stoichiometric reactions of trimethylaluminum with 2,6‐(MeOCH₂)₂C₆H₃OH (LH) revealed compounds L₃Al ( 1 ) and L₂AlMe ( 2 ). On the other hand reaction of 1 equiv. of LH with trimethylaluminum did not lead to the formation of complex LAlMe₂ ( 3 ), rather 2 together with Me₃Al were observed as a result of a disproportionation of 3 . Compounds 1 and 2 were characterized by elemental analysis, ¹H and ¹³C NMR spectroscopy and in the case of 1 by X‐ray diffraction. Derivative 2 underwent transmetalation with Ph₃SnOH, giving LSnPh₃ ( 4 ) as the result of a migration of ligand L from the aluminum to the tin atom. The identity of 4 was established by elemental analysis, ¹H, ¹³C and ¹¹⁹Sn NMR spectroscopy and ¹H, ¹¹⁹Sn HMBC experiments. The system 2 and B(C₆F₅)₃ in a 1:1 molar ratio was shown to be active in the polymerization of propylene oxide and ε‐caprolactone. Copyright © 2007 John Wiley & Sons, Ltd.     

On distribution of molecular weight in anionic polymerizates of caprolactam

Measurement has been made of the dependence of the molecular weight distribution on the ratio of the catalytic system components and on the polymerization time for polycaprolactam obtained by anionic polymerization. A bimodal character of the curves was observed for products made using molar ratios of activator (N-benzoylcaprolactam) to initiator (sodium dihydro-bis(methoxyethoxy)aluminate) of 1:1 and 1:3, when the polymerization times were less than 1 hr. This course is explained by the influence of fast side-reactions, mainly condensations. For a ratio of 3:1 of the components of the catalytic system, smooth integral distribution curves are obtained, accounting for a very fast decrease in the strong base concentration in the initial stages of the polymerization.