Interactions between the components in isotactic polypropylene blended with EPDM

The interaction of isotactic polypropylene with ethylene propylene diene terpolymer in their blends has been investigated by use of differential scanning calorimetry, dynamic mechanical analysis, wide- and small-angle x-ray scattering, and by investigating the nucleation and kinetics of crystallization of the iPP component under the polarization microscope. It is found, that the dispersion of the EPDM component in the iPP matrix is dependent on blend composition and is maximal at 10% EPDM content. An interface layer between the two components is formed by migration of iPP molecules into the EPDM phase. A model for this interface is proposed.     

Alloying by high dose ion implantation of iron into magnesium and aluminium

Alloys of the systems Fe–Al (mixable over the whole concentration range) and Fe–Mg (insoluble with each other) were produced by implantation of Fe ions into Al and Mg, respectively. The implantation energy was 200 keV and the ion doses ranged from 1 × 10₁₄ to 9 × 10₁₇cm^-2The obtained implantation profiles were determined by Auger electron spectroscopy depth profiling. Maximum iron concentrations reached were up to 60 at.% for implantation into Al and 94 at.% for implantation into Mg. Phase analysis of the implanted layers was performed by conversion electron Mössbauer spectroscopy and X‐ray diffraction. For implantation into Mg, two different kinds of Mössbauer spectra were obtained: at low doses paramagnetic doublets indicating at least two different iron sites and at high doses a dominant ferromagnetic six‐line‐pattern with a small paramagnetic fraction. The X‐ray diffraction pattern concluded that in the latter case a dilated αiron lattice is formed. For implantation into Al, the Mössbauer spectra were doublet structures very similar to those obtained at amorphous Fe–Al alloys produced by rapid quenching methods. They also indicated at least two different main iron environments. For the highest implanted sample a ferromagnetic six‐line‐pattern with magnetic field values close to those of Fe₃Al appeared.     

Three-dimensional atom probe study of the segregation behaviour of Ni91Pt9 alloy after sputtering

To investigate local ordering and segregation phenomenon in a Ni91Pt9-alloy after sputtering and annealing a 3D optical atom probe (OAP) has been used. The specimen tips have been prepared from polycrystalline samples. To sputter the samples a separate preparation chamber with a scannable Ar-sputter-gun is connected to the OAP vessel. When necessary, the sample can be electrically heated to induce segregation and cure the altered layer. After a heat treatment of a Ni91 at. %Pt 9 at.% specimen at 1100 K the surface of a (111)-oriented specimen is enriched in platinum by a factor of two in relation to the bulk. The phenomenon of short-range ordering has been investigated on the surface and in the subsurface volume. A 3D reconstruction of this annealed NiPt specimen shows regions with high concentration of platinum that gives an indication at short-range ordering. Uniform sputtering of the tip without a heat treatment induces a decisive depletion of Pt on the surface and the following subatomic layers. The atom-probe results of specimens in thermal equilibrium are in close agreement to further surface sensitive results obtained from Ion Scattering Spectroscopy (ISS) and Auger Electron Spectroscopy (AES).     

Estimation of multivariate binary density using orthogonal functions

In this paper, the authors studied certain properties of the estimate of Liang and Krishnaiah (1985, J. Multivariate Anal. 16, 162–172) for multivariate binary density. An alternative shrinkage estimate is also obtained. The above results are generalized to general orthonormal systems.     

Applications of coupled LC-GC: A review

Although coupled liquid chromatographygas chromatography (LC-GC) was first demonstrated ten years ago, only in the last few years has there been a sudden surge of interest in the technique. Approximately 70% of the total number of LC-GC applications have been published in the last two years (1987–88) alone. This review categorizes LC-GC publications into four main application areas: fossil fuels, foods, environmental samples, biologiical/pharmaceutical samples, and miscellaneous samples. Multidimensional separations carried out using other coupled-column chromatographic techniques (such as supercritical fluid chromatography (SFC) with GC, and on-line trace enrichment-GC) have also been included in this review.     

NiTi合金中马氏体相的低频力学谱研究

我们用最近研制成功的LMA型低频力学谱测试系统对NiTi合金马氏体相进行了在很大频率范围内（0．003～1Hz）的低频等温力学谱和温度谱的测量．我们研究的形状记忆合金NiTi（Ni50．2at％）试样长34mm，直径1mm细丝．经一定热处理，分别在333K．343K和353K做了内耗随频率的变化的测量。实验表明：频率越小，内耗越大，也就是内耗随频率减少而增大。同时我们采用阶梯升温的方法在八个温度下每个温度测量三种频率（1Hz，0．1Hz，0．01Hz）的内耗，结果清楚地表明：不同频率下，内耗峰都出现在372K（99℃）。而且频率越低，峰高越高。这是具有相变峰的特点：相变峰的峰温不随测量频率不同而变化，相变峰高度随频率减少而增大。我们还测量了在1Hz与0．5Hz频率下内耗随温度的变化。本文用马氏体相的位错理论初步讨论了上述实验结果。     

Development and investigation of perovskite (ABO3)-type oxides for power generation

Critical problems of the present approach of electrolytes for Solid Oxide Fuel Cells (SOFCs) for commercialization are discussed. Major progress is expected from the development of materials based on the “SEA (Single Element Arrangement)” concept. The galvanic cell consists in this case basically of a single chemically homogeneous compound, which functions as electrodes at high and low activity and as electrolyte at intermediate activities of the electroactive component. In view of the large structural flexibility of the chemical nature of the constitutents, we explored perovskite (ABO₃)-type compounds to be used as SEAs for SOFCs. Results of studies on Pr-substituted LSGM and Fe-substituted SrSnO₃ perovskite-type oxides are presented. For instance, SrSn_1-xFe_xO_3-δ with x=0.1 exhibits p and n-type electronic conduction at the cathode and anode sides of the SOFC, respectively, while oxide ion conduction prevails at intermediate oxygen partial pressures. The SEA concept is also applicable for other devices in the field of Ionics.