Temperature effects on surface activity and application in oxidation of toluene derivatives of CTAB-SDS with KMnO4

The γ_cmc values of CTAB-SDS decrease from 63.67 mN/m at 10‡C to 36.38 mN/m at 90‡C, slightly lower than those of either CTAB or SDS. Correspondingly, the CMC of CTAB-SDS decreases almost by half. The increase of surface activity of CTAB-SDS can be attributed to the relatively weak electrostatic interaction at high temperature, which is supported by the increase of solubility of CTAB-SDS with rise in temperature. Catalytic effect on oxidation of toluene derivatives with potassium permanganate follows the order CTAB-SDS > SDS > CTAB. This is not caused by the dissociative effect of CTAB-SDS with low surface activity at low temperature, as seen from the fact that almost all oxidative products can be retrieved for different toluene derivatives and surfactants by mimicking the conditions of reaction. In the emulsifications of toluene derivatives at 90‡C, the time that turbid water layers of surfactant solutions take to become clear is the same as that of the catalytic effect on oxidation of toluene derivatives. Thus, it can be inferred that surfactants can improve the oxidation yields of toluene derivatives by increasing the contact between two reacting phases.     

Nanostructured thermoset epoxy resin templated by an amphiphilic poly(ethylene oxide)‐block‐poly(dimethylsiloxane) diblock copolymer

An amphiphilic poly(ethylene oxide)‐block‐poly(dimethylsiloxane) (PEO–PDMS) diblock copolymer was used to template a bisphenol A type epoxy resin (ER); nanostructured thermoset blends of ER and PEO–PDMS were prepared with 4,4′‐methylenedianiline (MDA) as the curing agent. The phase behavior, crystallization, hydrogen‐bonding interactions, and nanoscale structures were investigated with differential scanning calorimetry, Fourier transform infrared spectroscopy, transmission electron microscopy, and small‐angle X‐ray scattering. The uncured ER was miscible with the poly(ethylene oxide) block of PEO–PDMS, and the uncured blends were not macroscopically phase‐separated. Macroscopic phase separation took place in the MDA‐cured ER/PEO–PDMS blends containing 60–80 wt % PEO–PDMS diblock copolymer. However, the composition‐dependent nanostructures were formed in the cured blends with 10–50 wt % PEO–PDMS, which did not show macroscopic phase separation. The poly(dimethylsiloxane) microdomains with sizes of 10–20 nm were dispersed in a continuous ER‐rich phase; the average distance between the neighboring microdomains was in the range of 20–50 nm. The miscibility between the cured ER and the poly(ethylene oxide) block of PEO–PDMS was ascribed to the favorable hydrogen‐bonding interaction. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 3042–3052, 2006     

Exploitation of introducing of catalytic centers into layer galleries of layered silicates and related epoxy nanocomposites. I. Epoxy nanocomposites derived from montmorillonite modified with catalytic surfactant‐bearing carboxyl groups

Montmorillonite (MMT) was modified with the acidified cocamidopropyl betaine (CAB) and the resulting organo‐montmorillonite (O‐MMT) was dispersed in an epoxy/methyl tetrahydrophthalic anhydride system to form epoxy nanocomposites. The intercalation and exfoliation behavior of the epoxy nanocomposites were examined by X‐ray diffraction and transmission electron microscopy. The curing behavior and thermal property were investigated by in situ Fourier transform infrared spectroscopy and DSC, respectively. The results showed that MMT could be highly intercalated by acidified CAB, and O‐MMT could be easily dispersed in epoxy resin to form intercalated/exfoliated epoxy nanocomposites. When the O‐MMT loading was lower than 8 phr (relative to 100 phr resin), exfoliated nanocomposites were achieved. The glass‐transition temperatures (T_g's) of the exfoliated nanocomposite were 20 °C higher than that of the neat resin. At higher O‐MMT loading, partial exfoliation was achieved, and those samples possessed moderately higher T_g's as compared with the neat resin. O‐MMT showed an obviously catalytic nature toward the curing of epoxy resin. The curing rate of the epoxy compound increased with O‐MMT loading. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 1192–1198, 2004     

Synthesis and characterization of polyaniline/graphite conducting nanocomposites

A new method for the synthesis of exfoliated graphite and polyaniline (PANI)/graphite nanocomposites was developed. Exfoliated graphite nanosheets were prepared through the microwave irradiation and sonication of synthesized expandable graphite. The nanocomposites were fabricated via the in situ polymerization of the monomer at the presence of graphite nanosheets. The as-synthesized graphite nanosheets and PANI/graphite nanocomposite materials were characterized with Fourier transform infrared spectroscopy, scanning electron microscopy, transmission electron microscopy, and thermogravimetric analysis (TGA). The conductivity of the PANI/graphite nanocomposites was dramatically increased over that of pure PANI. TGA indicated that the incorporation of graphite greatly improved the thermal stability of PANI. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 1972–1978, 2004     

Differential pulse anodic stripping voltammetric determination of traces of copper with a tobramycin-Nafion modified electrode.

A Nafion-modified glassy carbon electrode incorporated with tobramycin for the voltammetric stripping determination of Cu2+ has been explored. The electrode was fabricated by tobramycin containing Nafion on the glassy carbon electrode surface. The modified electrode exhibited a significantly increased sensitivity and selectivity for Cu2+ compared with a bare glassy carbon electrode and the Nafion modified electrode. Cu2+ was accumulated in HAc-NaAc buffer (pH 4.6) at a potential of -0.6 V (vs. SCE) for 300 s and then determined by differential pulse anodic stripping voltammetry. The effects of various parameters, such as the mass of Nafion, the concentration of tobramycin, the pH of the medium, the accumulation potential, the accumulation time and the scan rate, were investigated. Under the optimum conditions, a linear calibration graph was obtained in the concentration range of 1.0 x 10(-9) to 5.0 x 10(-7) mol l(-1) with a correlation coefficient of 0.9971. The relative standard deviations for eight successive determinations were 4.3 and 2.9% for 1.0 x 10(-8) and 2.0 x 10(-7) mol l(-1) Cu2+, respectively. The detection limit (three times signal to noise) was 5.0 x 10(-10) mol l(-1). A study of interfering substances was also performed, and the method was applied to the direct determination of copper in water samples, and also in analytical reagent-grade salts with satisfactory results.     

2‐Cyanoprop‐2‐yl dithiobenzoate mediated reversible addition–fragmentation chain transfer polymerization of acrylonitrile targeting a polymer with a higher molecular weight

The reversible addition–fragmentation chain transfer (RAFT) polymerization of acrylonitrile (AN) mediated by 2‐cyanoprop‐2‐yl dithiobenzoate was first applied to synthesize polyacrylonitrile (PAN) with a high molecular weight up to 32,800 and a polydispersity index as low as 1.29. The key to success was ascribed to the optimization of the experimental conditions to increase the fragmentation reaction efficiency of the intermediate radical. In accordance with the atom transfer radical polymerization of AN, ethylene carbonate was also a better solvent candidate for providing higher controlled/living RAFT polymerization behaviors than dimethylformamide and dimethyl sulfoxide. The various experimental parameters, including the temperature, the molar ratio of dithiobenzoate to the initiator, the molar ratio of the monomer to dithiobenzoate, the monomer concentration, and the addition of the comonomer, were varied to improve the control of the molecular weight and polydispersity index. The molecular weights of PANs were validated by gel permeation chromatography along with a universal calibration procedure and intrinsic viscosity measurements. ¹H NMR analysis confirmed the high chain‐end functionality of the resultant polymers. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 1272–1281, 2007     

Kinetic behaviour of aluminum naphthenate/benzene system in process of gelation and degradation

The kinetic behaviour of aluminum naphthenate/benzene system in the process of gelation and degradation was systematically studied. The results obtained from the kinetic experiments indicated that the gelation stage was in accordance with a kinetic model of an auto-catalytic first-order reaction, and the degradation stage was a simple first-order reaction. The rate constants in these two stages at various temperaturs were measured. And the determined apparent activation energies for the gelation stage and for the degradation stage are 27.5±2.0 and 37.7±2.3 kJ/mol, respectively.     

Temperature dependence of magnetization in nanocrystalline FeCoZr alloy

The temperature dependence of magnetization of a nanocrystalline Fe₆₀Co₃₀Zr₁₀ alloy annealed at various temperatures to varying crystal sizes was investigated down to 5 K in the field range up to 5 T. The fitting procedure gave T^3/2 as the leading term irrespective of the crystal size. We suggest that the increase of the coefficient by this term for smaller crystals may be connected to an increased relative volume of their surface.     

Dialdehyde starch‐crosslinked chitosan films and their antimicrobial effects

For improved mechanical and water‐swelling properties of chitosan films, a series of transparent films were prepared with dialdehyde starch as a crosslinking agent. Fourier transform infrared and X‐ray analysis results demonstrated that the formation of Schiff's base disturbed the crystallization of chitosan. The mechanical properties and water‐swelling properties of the films were significantly improved. The best values of the tensile strength and breaking elongation were 113.1 MPa and 27.0%, respectively, when the dialdehyde starch content was 5%. All the crosslinked films still retained obvious antimicrobial effects toward S. aureus and E. coli, and they showed potential for biomedical applications. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 993–997, 2003     

Apparatus for High-Resolution Solid Hydrogen Matrix Isolation Spectroscopy and Its Application

Apparatus integrating a Fourier transform-infrared (FT-IR) spectrometer and a mid-infrared difference frequency generation (DFG) laser spectrometer was built for the study of the matrix isolation spectrum in solid molecular hydrogen. A 3-cm-long molecular hydrogen crystal was grown in a liquid-helium Dewar, and its infrared absorption spectrum in the 1-5 μm region was recorded to test the system. The W₀(0) (ν=0←0, J=6←0) line around 2410 cm⁻¹ of solid hydrogen was investigated with the DFG laser spectroscopy. High-resolution matrix isolation spectrum of CO² co-deposited with hydrogen on a BaF₂ cold plate at liquid-helium temperature was studied.