Use of blowing catalysts for integral skin polyurethane applications in a controlled molecular architectural environment: Synthesis and impact on ultimate physical properties

Polyurethane elastomers of a controlled molecular architecture were synthesized using a two‐step polymerization technique. The building blocks of the elastomeric materials included urea–urethane prepolymers end‐capped with diisocyanate groups and had an exact number of urea groups at both ends. Two‐dimensional bifurcated hydrogen‐bonding networks incorporating the urea groups were, with differential scanning calorimetric and dynamic mechanical thermal analyzer techniques, responsible for the increase in the glass‐transition temperature (T_g) of the hard block and sharp interface morphology between the pure “hard” domains and pure “soft” domains. The higher extent of the phase separation between the two phases contributed to higher elastic moduli for the hard blocks and higher tensile strength for the elastomeric samples. Higher elongation values were attributed to the liberation of the elastomeric chain ends that otherwise would have been constrained in the interface region. The higher T_g values of the hard blocks corresponded to an increase in the hardness values and a decrease in the tear‐strength values. The increase in the amount of urea groups within the hard segments, as a result of the increased amount of water and blowing catalyst, resulted in elastomeric foams with higher open‐cell content. This resulted in lower resilience values as measured using the pendulum rebound test and was attributed to the ability of the open cells to absorb and dissipate energy. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 2526–2536, 2002     

Aider: Angle-of-incidence-derivative ellipsometry and reflectometry

A technique is proposed for the direct measurement of the derivatives ?ψ/??, ?Δ/?? and ?$\text{R}$/?? (or ? In $\text{R}$/? ?) of the ellipsometric (ψ, Δ) and reflectance ($\text{R}$) parameters of an optically isotropic surface with respect to the angle of incidence (?). A sinusoidal rotational oscillation of small amplitude

is applied to the sample around an axis in its surface perpendicular to the plane of incidence and the resulting ac/dc photoelectric signal-ratio η is measured in an ellipsometer with stationary polarizing and analyzing optics. From three such measurements η₁, η₂, η₃ at three different settings of the ellipsometer optics, the amplitudes of the sinusoidal perturbations

,

and

of the ellipsometric and reflectance parameters, caused by the angle-of-incidence oscillation

, can be determined. If

,

and

are divided by

, we get the desired derivatives ?ψ/??, ?Δ/?? and ? In $\text{R}$/??. This technique of Angle-of-Incidence-Derivative Ellipsometry and Reflectometry (given the acronym AIDER) promises to open up new possibilities in surface optics particularly for the measurement of the optical properties of film-substrate systems.     

Identification of wild collected mosquito vectors of diseases using gas chromatography–mass spectrometry in Jazan Province,Saudi Arabia

Thirty‐three species of mosquitoes have been reported from the Kingdom of Saudi Arabia. Several of these mosquitoes, Anopheles gambiae Giles s.l., Anopheles stephensi Liston, Culex pipiens Linnaeus, Culex quinquefasciatus Say, Culex tritaeniorhynchus Giles, Stegomyia aegypti (Linnaeus) and Aedimorphus vexans arabiensis (Patton) are known vectors of human and animal diseases. In this study, the cuticular hydrocarbon profiles of eight mosquito species using gas chromatography–mass spectrometry were analyzed. Wild collected fourth‐instar larvae were reared, and single, newly emerged, unfed adult females were used for the analysis. A total of 146–160 peaks were detected from the cuticular extracts by gas chromatography. Repeated analysis of variance (ANOVA) and Tukey HSD Post Hoc test was used to test for quantitative differences in relative hydrocarbon quantity. In addition, a linear regression model was applied using Enter method to determine the diagnostic peaks for the eight mosquito specimens. The ANOVA test indicated that relative peaks were significant (P < 0.05) when selected pairs of peaks were compared. Also, seven compounds showed qualitative differences among the five mosquito vectors tested. The classes of constituents present were n‐alkanes, monomethylalkanes, dimethylalkanes, trimethylalkanes, alkenes, branched aromatic hydrocarbons, aldehydes and esters. These compounds have a carbon chain length ranging from 8 to 18 carbons. The most abundant compound in all adult mosquito specimens was n‐hexylacrylate [retention time (RT) 6.73 min], which was not detected in Cx. pipiens. In Cx. pipiens, the most abundant peak was benzaldehyde (RT 2.98 min). Gas chromatography–mass spectrometry is a suitable method to identify adult mosquitoes, especially from focal areas of public health concern such as Jazan Province, Saudi Arabia. This method allows a wide range of adult collected material to be identified with high accuracy. Copyright © 2013 John Wiley & Sons, Ltd.     

Synthesis and Characterization of Self-Assembling Some Thiol Surfactants on Gold Nanoparticles

The purpose of this work is to study the self-assembling of some synthesized thiol surfactants namely (mercaptopropane-, mercaptohexane-, mercaptooctane-, and mercaptodecane sodium sulfonate) on the fabricated gold nanoparticles. The self-assembling of these surfactants on gold nanoparticles characterized using different techniques such as FTIR spectroscopy, UV spectroscopy, and transmission electron microscopy (TEM). Spectroscopic evidence suggests that the synthesized thiol surfactants have been attached to the gold nanoparticles. The effect of self-assembling of these surfactants on the size of the gold nanoparticles was studied using TEM images. The growth of the gold nanoparticles was investigated with respect to the increase of alkyl chain in the synthesized thiol surfactants. The results show that the stabilization of gold nanoparticles was affected by the increase in alkyl chain length of these surfactants. The effect of gold nanoparticles on the interfacial tension and the emulsion stability of these surfactants with crude oil was studied.     

Synthesis and in vitro anticancer activity of some novel tetrahydroquinoline derivatives bearing pyrazol and hydrazide moiety

A new series of tetrahydroquinoline derivatives having pyrazol and hydrazide moieties were synthesized for the purpose of anticancer cell line evaluation. Syntheses of these compounds were firstly achieved by one pot four reactions. The reaction of 3-amino-tetrahydro-1H-pyrazolo [3,4-b]quinolin with aldehydes, indoline-2,3-dione derivatives to give 9a-c , 11a-c , and 13a,b , respectively. In similar manner for biological comparison, the reactions of compound 5 with the same aldehydes and indoline-2,3-dione derivatives to give 19a-c and 20a-c . The newly synthesized compounds were examined in vitro for their cytotoxic activity against HepG-2 and A549 cancer cells. The compounds 11a-c and 20a-c showed promising activity as anticancer agents against HepG-2 and A549 cancer cells.     

Microstructural study of different LDH morphologies obtained via different synthesis routes

In order to better understand the relationship between LDH synthesis parameters and their particle sizes, diverse carbonate intercalated NiAl-LDH phases were prepared using different coprecipitation conditions and their structure, microstructure and morphology were characterized. The samples were synthesized by coprecipitation either at constant pH, in strong alkaline medium or using urea decomposition. The influence of a post-synthesis hydrothermal treatment was also investigated. A well crystalline NiAl-CO₃ phase but containing a high stacking fault density was obtained by combining a strong basic medium and hydrothermal treatment at 120 °C for 24 h. Interestingly, the hydrothermal treatment increases the crystallinity of the samples but does not eliminate stacking faults. The crystallite sizes determined by modeling X-ray diffraction peak broadening with linear combinations of spherical harmonics are fully consistent with TEM observations confirming the validity of the approach used and indicating that the particles are probably small single crystals.     

Chromium(VI) Forms Thiolate Complexes with gamma-Glutamylcysteine, N-Acetylcysteine, Cysteine, and the Methyl Ester of N-Acetylcysteine

Reaction of potassium dichromate with gamma-glutamylcysteine, N-acetylcysteine, and cysteine in aqueous solution resulted in the formation of 1:1 complexes of Cr(VI) with the cysteinyl thiolate ligand. The brownish red Cr(VI)-amino acid/peptide complexes exhibited differential stability in aqueous solutions at 4 degrees C and ionic strength = 1.5 M, decreasing in stability in the order: gamma-glutamylcysteine > N-acetylcysteine > cysteine. (1)H, (13)C, and (17)O NMR studies showed that the amino acids act as monodentate ligands and bind to Cr(VI) through the cysteinyl thiolate group, forming RS-Cr(VI)O(3)(-) complexes. No evidence was obtained for involvement of any other possible ligating groups, e.g., amine or carboxylate, of the amino acid/peptide in binding to Cr(VI). EPR studies showed that chromium(V) species at g = 1.973-4 were formed upon reaction of potassium dichromate with gamma-glutamylcysteine and N-acetylcysteine. Reaction of potassium dichromate or sodium dichromate with N-acetylcysteine and the methyl ester of N-acetylcysteine in N,N-dimethylformamide (DMF) also led to the formation of RS-Cr(VI)O(3)(-) complexes as determined by UV/vis, IR, and (1)H NMR spectroscopy. Thus, an early step in the reaction of Cr(VI) with cysteine and cysteine derviatives in aqueous and DMF solutions involves the formation of RS-CrO(3)(-) complexes. The Cr(VI)-thiolate complexes are more stable in DMF than in aqueous solution, and their stability towards reduction in aqueous solution follows the order cysteine < N-acetylcysteine < gamma-glutamylcysteine < glutathione.     

Monolayer-protected gold nanoparticles by the self-assembly of micellar poly(ethylene oxide)-b-poly(epsilon-caprolactone) block copolymer

A study is presented of the preparation of gold nanoparticles incorporated into biodegradable micelles. Poly(ethylene oxide)-b-poly(epsilon-caprolactone) (PEO-b-PCL) copolymer was synthesized by ring-opening polymerization, and the hydroxyl end group of the PCL block was modified with thioctic acid using dicyclohexyl carbodiimide as the coupling reagent. The PEO-b-PCL-thioctate ester (TE) thus obtained was used in a later step to form monolayer protected gold nanoparticles via the thioctate spacer. Gold nanoparticles stabilized with the PEO-b-PCL block (named Au/Block (x/y), where x/y is the mole feed ratio between HAuCl4 and PEO-b-PCL-TE) were prepared and analyzed. Au/Block (1/1), Au/Block (2/1), and Au/Block (3/1) nanoparticles were found to form stable dispersions in the organic solvents commonly used to dissolve the unlabeled block copolymer. The average diameter of the nanoparticles was determined by transmission electron microscopy (TEM) and found to be 6+/-2 nm. Au/Block (4/1) nanoparticle dispersions in organic solvents, on the other hand, were not stable and produced large gold clusters (50-100 nm). Cluster formation was attributed to the low grafting density of the block copolymer, which facilitates agglomeration. For Au/Block (12/1), along the same trend, only an insoluble product was isolated. Micelles in water were prepared by the slow addition of the dilute Au/Block solution in dimethylformamide into a large excess of water with vigorous stirring. Au/Block (1/1) and Au/Block (2/1) formed nanosized structures of 5-7 nm. TEM images of stained Au/Block (1/1) micelles, made in water, clearly showed the formation of core-shell structures. Au/Block (3/1) micelles, on the other hand, were not stable and large agglomerates a few microns in size were observed. The study focuses on the synthesis, characterization, and aggregation behavior of gold-loaded PEO-b-PCL block copolymer micelles, a potential system for drug delivery in conjunction with tissue and subcellular localization studies.     

The Surface and Thermodynamic Properties of Ethoxylated Sodium Monoalkyl Sulfosuccinate Surfactants

A series of ethoxylated sodium monooctyl sulfosuccinates [E(n)SMOSS] and ethoxylated sodium monolauryl sulfosuccinates [E(n)SMLSS] have different units of ethylene oxide (n = 9, 14, 23) were synthesized. The surface and thermodynamic properties of these surfactants have been compared with sodium dioctyl sulfosuccinate surfactant (SDOSS) as a commonly used surfactant. The surface tension measurements at 25, 35, 45, and 55°C were used to determine of the critical micelle concentration (CMC) and surface active properties of these surfactants. The effect of the ethylene oxide (EO) unit and the alkyl chain length on the surface properties for the prepared surfactants was studied. The results show that the ethoxylated sodium monoalkyl sulfosuccinates generally have lower values of CMC than that of sodium dioctyl sulfosuccinate. The values of surface active parameters indicate that the ethoxylated sodium monooctyl sulfosuccinates and ethoxylated sodium monolauryl sulfosuccinates surfactants have adsorption properties better than the sodium dioctyl sulfosuccinate surfactant as a resulted presence of ethylene oxide in molecules of the prepared surfactants. The thermodynamic parameters show that the (EO) unites in the chemical structure of ethoxylated sodium monoalkyl sulfosuccinate surfactants improve their micellization and adsorption properties.     

Circular polarization beam splitter that uses frustrated total internal reflection by an embedded symmetric achiral multilayer coating

A symmetric achiral trilayer structure, which consists of a high-index center layer sandwiched between two identical low-index films and embedded in a high-index prism, is designed to produce equal and opposite quarter-wave retardation in reflection and transmission and equal throughput for the p and s polarization at oblique incidence. Such a device splits a beam of incident linearly polarized light into two orthogonally circularly polarized components of equal power that travel in different directions. A visible (633-nm) design that operates at a 60 degree angle of incidence and an infrared (10.6-microm) 45 degree cube design are presented. The spectral and angular sensitivities of the device are also considered.