Therapeutic monitoring of imipramine and desipramine by micellar liquid chromatography with direct injection and electrochemical detection

A micellar liquid chromatographic (MLC) procedure was developed for the clinical monitoring of imipramine and its active metabolite, desipramine. The determination of these highly hydrophobic substances was carried out after direct injection of the serum samples using a mobile phase composed of 0.15 m SDS--6% (v/v) pentanol buffered at pH 7, pumped at 1.5 mL/min into a C(18) column (250 x 4.6 mm), and electrochemical detection at 650 mV. Using this MLC method, calibration was linear (r > 0.995) and the limits of detection (ng/mL) were 0.34 and 0.24 for imipramine and desipramine, respectively. Repeatabilities and intermediate precision were tested at three different concentrations in the calibration range and a CV (%) below 2.2 was obtained. In this MLC procedure, the serum is determined without treatment, thus allowing repeated serial injections without changes in retention factors, and reducing the time and consumables required to carry out the pretreatment process. The assay method can be applied to the routine determination of serum imipramine and its metabolite in therapeutic drug monitoring.     

Preconcentration and speciation of chromium in waters using solid-phase extraction and atomic absorption spectrometry

A method for the preconcentration and speciation of chromium was developed. After formation of an anionic compound with ethylenediaminetetraacetic acid (CrY(-)), Cr (VI) and Cr (III) are retained on a strong anionic phase (SAX) and controlled elution with 0.5 M NaCl permits their speciation. The retention and elution conditions were optimised, and interferences due to the presence of other ions such as Mg(II), Mn(II), Sn(II), Fe(III), Ba(II), Al(III), Ca(II), chloride, iodine, bromide, fluoride, sulphate, phosphate, bicarbonate and nitrate were studied. The detection limits were 0.4 mug l(-1) and 1.1 mug l(-1) for Cr(III) and Cr(VI), respectively, and reproducibility was 9%. The results obtained for speciation of chromium by the proposed method in wastewaters are in agreement with the values obtained by a reference method for a 95% confidence level.     

Diamond electrode facilitated electrosynthesis of water and wastewater treatment oxidants

While diamond electrodes have been commonly used to generate ^?OH to treat a variety of persistent water and wastewater micropollutants, mass transfer limitations and the non-selective, short-lived nature of the ^?OH restrict the degradation to the solution at, or near, the electrode surface. However, diamond electrodes can generate oxidizing species that facilitate micropollutant degradation in the bulk water solution. These include persulfate, sulfate radicals, peroxodiphosphate, ferrate, permanganate, reactive chlorine species, hydrogen peroxide, and ozone, which have been reported during electrochemical treatment of water with diamond electrodes. Although still restricted to specialized applications, recent studies, summarized in this review, have proven the electrogeneration of these additional oxidant species to be effective. They have shown the adaptability and potential of diamond electrode-based water treatment to mitigate the presence of micropollutants in water.     

Threshold crack speed controls dynamical fracture of silicon single crystals

Fracture experiments of single silicon crystals reveal that after the critical fracture load is reached, the crack speed jumps from zero to approximately 2 km/sec, indicating that crack motion at lower speeds is forbidden. This contradicts classical continuum fracture theories predicting a continuously increasing crack speed with increasing load. Here we show that this threshold crack speed may be due to a localized phase transformation of the silicon lattice from 6-membered rings to a 5-7 double ring at the crack tip.     

Electron microscopy characterization of nanostructured carbon obtained from chlorination of metallocenes and metal carbides

In this work we report some new well-defined carbon nanostructures produced by direct chlorination of metallocenes (ferrocene and cobaltocene) and NbC, at temperatures from 100 to 900 degrees C. Thus, amorphous carbon nanotubes with variable dimensions depending on reaction temperature were produced from ferrocene. When cobaltocene is the carbon precursor the main product are solid amorphous nanospheres. The high refractory metal carbide NbC as carbon source favours the growth of nanospherical cabbage-like particles with a higher degree of graphene sheets order. Besides, NbC crystallites encapsulated in an amorphous carbon shell were also found at lower temperatures (T< or =700 degrees C).     

Dynamics of the dissociation of hydrogen on stepped platinum surfaces using the ReaxFF reactive force field

The dissociation of hydrogen on eight platinum surfaces, Pt(111), Pt(100), Pt(110), Pt(211), Pt(311), Pt(331), Pt(332), and Pt(533), has been studied using molecular dynamics and the reactive force field, ReaxFF. The force field, which includes the degrees of freedom of the atoms in the platinum substrate, was used unmodified with potential parameters determined from previous calculations performed on a training set exclusive of the surfaces considered in this work. The energetics of the eight surfaces in the absence of hydrogen at 0 K were first compared to previous density functional theory (DFT) calculations and found to underestimate excess surface energy. However, taking Pt(111) as a reference state, we found that the trend between surfaces was adequately predicted to justify a relative comparison between the various stepped surfaces. To assess the strengths and weaknesses of the force field, we performed detailed simulations on two stepped surfaces, Pt(533) and Pt(211), and compared our findings to published experimental and theoretical results. In general, the absolute magnitude of reaction rate predictions was low, a result of the force field's tendency to underpredict surface energy. However, when normalized, the simulations show the correct linear scaling with incident energy and angular dependence at collision energies where a direct dissociation mechanism is observed. Because ReaxFF includes all degrees of freedom in the substrate, we carried out simulations aimed at understanding surface-temperature effects on Pt(533). On the basis of the results on Pt(533)/Pt(211), we studied the reaction of hydrogen at normal incidence on all eight surfaces in a range of energies where we anticipated the force field to give reasonable qualitative trends. These results were subsequently fit to a simple linear model that predicts the enhanced reactivity of surfaces containing 111-type atomic steps versus 100-type atomic steps. This model provides a simple framework for predicting high-energy/high-temperature kinetics of complex surfaces not vicinal to Pt(111).     

Membrane association and contact formation by a synthetic analogue of polymyxin B and its fluorescent derivatives

sP-B is a synthetic analogue of the natural lipopeptide antibiotic polymyxin B (PxB) that maintains the ability of the parent compound to form vesicle-vesicle contacts and induce lipid exchange. Exchange is selective, and only monoanionic phospholipids such as 1-palmitoyl-2-oleoyl-glycero-sn-3-phosphoglycerol (POPG) are transferred, whereas dianionic phospholipids such as 1-palmitoyl-2-oleoyl-glycero-sn-3-phosphate (POPA) are not, as shown by fluorescence experiments based on the excimer/monomer ratio of pyrene-labeled phospholipids. Synthetic fluorescent analogues of sP-B are used to investigate the peptide position and orientation in the intermembrane contacts: sP-Bw, an analogue that contains D-tryptophan (D-Trp) instead of the naturally occurring D-phenylalanine, and sP-Bpy, incorporating a pyrene group at the N-terminus. Tryptophan fluorescence, anisotropy, and quenching measurements performed with sP-Bw indicate that the peptide binds and inserts in anionic vesicles of POPG and POPA. However, significant differences are seen depending on the lipid composition, as also demonstrated by fluorescence resonance energy transfer (FRET) experiments from Trp to 7-nitro-2-1,3-benzoxadiazol (NBD) groups at the interface. Intermolecular FRET using sP-Bw as the donor and sP-Bpy as the acceptor indicates self-association of the peptide, possibly forming dimers, when bound to POPG vesicles at concentrations that induce the vesicle-vesicle contacts.     

Atomistic-scale simulations of the initial chemical events in the thermal initiation of triacetonetriperoxide

To study the initial chemical events related to the detonation of triacetonetriperoxide (TATP), we have performed a series of molecular dynamics (MD) simulations. In these simulations we used the ReaxFF reactive force field, which we have extended to reproduce the quantum mechanics (QM)-derived relative energies of the reactants, products, intermediates, and transition states related to the TATP unimolecular decomposition. We find excellent agreement between the QM-predicted reaction products and those observed from 100 independent ReaxFF unimolecular MD cookoff simulations. Furthermore, the primary reaction products and average initiation temperature observed in these 100 independent unimolecular cookoff simulations match closely with those observed from a TATP condensed-phase cookoff simulation, indicating that unimolecular decomposition dominates the thermal initiation of the TATP condensed phase. Our simulations demonstrate that thermal initiation of condensed-phase TATP is entropy-driven (rather than enthalpy-driven), since the initial reaction (which mainly leads to the formation of acetone, O(2), and several unstable C(3)H(6)O(2) isomers) is almost energy-neutral. The O(2) generated in the initiation steps is subsequently utilized in exothermic secondary reactions, leading finally to formation of water and a wide range of small hydrocarbons, acids, aldehydes, ketones, ethers, and alcohols.     

Thermal decomposition of RDX from reactive molecular dynamics

We use the recently developed reactive force field ReaxFF with molecular dynamics to study thermal induced chemistry in RDX [cyclic-[CH(2)N(NO(2))](3)] at various temperatures and densities. We find that the time evolution of the potential energy can be described reasonably well with a single exponential function from which we obtain an overall characteristic time of decomposition that increases with decreasing density and shows an Arrhenius temperature dependence. These characteristic timescales are in reasonable quantitative agreement with experimental measurements in a similar energetic material, HMX [cyclic-[CH(2)N(NO(2))](4)]. Our simulations show that the equilibrium population of CO and CO(2) (as well as their time evolution) depend strongly of density: at low density almost all carbon atoms form CO molecules; as the density increases larger aggregates of carbon appear leading to a C deficient gas phase and the appearance of CO(2) molecules. The equilibrium populations of N(2) and H(2)O are more insensitive with respect to density and form in the early stages of the decomposition process with similar timescales.