Kinetics of the O2, Pt/YSZ interface at moderate temperature in the presence of C3H8 in the gas phase

The catalytic activity of polycrystalline Pt deposited on Yttria Stabilized Zirconia (YSZ) for the oxidation of propane to CO₂ can be affected using the effect of Non-faradaic Electrochemical Modification of Catalytic Activity (NEMCA). It was found that by applying positive overpotentials and thus, supplying O^2- onto catalyst surface, up to 3.2-fold increase in the catalytic rate of C₃H₈ oxidation could be obtained at 365 °C. At 305 °C, no effect was evidenced. Using cyclic voltammetry and impedance spectroscopy, we have shown the modifications induced by the addition of C₃H₈ on the kinetics of the 0₂, Pt/YSZ interface in the temperature range 300–400 °C. A decrease of the coverage of adsorbed oxygen species produced electrochemically was evidenced as well as a decrease of the oxygen electrode reaction rate under anodic potential. Paper presented at the 8th EuroConference on Ionics, Carvoeiro, Algarve, Portugal, Sept. 16–22, 2001.     

Electrochemical promotion of catalyst surfaces deposited on ionic and mixed conductors

The effect of non-Faradaic electrochemical modification of catalytic activity (NEMCA) or electrochemical promotion (EP) was investigated on Pt films deposited on Y₂O₃-stabilized-ZrO₂ (YSZ), an O²⁻ conductor, TiO₂, a mixed conductor, and Nafion 117 solid polymer electrolyte (SPE), a H⁺ conductor and also on Pd films deposited on YSZ and β″-Al₂O₃ a Na⁺ conductor. Four catalytic systems were investigated, i.e. C₂H₆ oxidation on Pt/YSZ, C₂H₄ oxidation on Pd/YSZ and Pd/β″-Al₂O₃, C₂H₄ oxidation on Pt/TiO₂ and H₂ oxidation on Pt/Nafion 117 in contact with 0.1 M aqueous KOH solution. In all cases pronounced and reversible non-Faradaic electrochemical modification of catalytic rates was observed with catalytic rate enhancement up to 2000% and Faradaic efficiency values up to 5000. All reactions investigated exhibit a pronounced electrophobic behaviour which is due to the weakening of chemisorptive oxygen bond at high catalyst potentials. Ethane oxidation, however, also exhibits electrophilic behaviour at low potentials due to weakened binding of carbonaceous species on the surface. The general features of the phenomenon are similar for all four cases presented here showing that the NEMCA effect is a general, electrochemically induced, promoting catalytic phenomenon not depending on the reaction and the type of supporting electrolyte. Paper presented at the 2nd Euroconference on Solid State Ionics, Funchal, Madeira, Portugal, Sept. 10–16, 1995     

Possibilities of NOx and CHx determination using galvanic cells with perovskite-electrodes on YSZ

Perovskite-type mixed oxides with the formula La_1−xA_xMe_1−yB_yO_3±δ (x=0.01...0.2; y=0.01...0.5; A=Ca, Sr; Me=Cr, Mn, Fe, Co; B=Mg, Ga) were investigated with the aim to use the oxides as electrode materials for galvanic cells with Y₂O₃-stabilized ZrO₂ solid electrolytes (YSZ). The catalytic activity of the oxides for the oxidation, reduction and decomposition of gas components was varied by changing the transition metal and by partial substitution of lanthanum and the metal. The behaviour of different substituted lanthanum chromite/YSZ and manganite/YSZ electrodes in the presence of nitric oxides (NO_x) and combustible components (CH_x) in gases containing oxygen was investigated. Various electrode combinations were tested in gas-symmetrical cells. For the NO determination cells with a catalytically active Pt electrode and a La_0.8Sr_0.2MnO₃ electrode with a low catalytic activity for the decomposition of NO were used. The results show the possible quantitative measurement at low and constant p(O₂) on the basis of a calibration. For the determination of C₃H₆ a CH_x-sensitive Au and an O₂-sensitive La_0.99Sr_0.01CrO₃ electrode were combined in a potentiometric thick film sensor. In gases containing oxygen with small amounts of C₃H₆ the sensor provided a utilizable voltage in dependence of the C₃H₆ concentration. Paper presented at the 3rd Euroconference on Solid State Ionics, Teulada, Sardinia, Italy, Sept. 15–22, 1996     

Promotion of surface SOx on the selective catalytic reduction of NO by hydrocarbons over Ag/Al2O3

The promotion of sulfur oxides on the selective catalytic reduction (SCR) of NO by hydrocarbons in the presence of a low concentration of sulfur oxides over Ag/Al₂O₃ has been investigated by a flow reaction test and in situ infrared spectroscopy. When the C₃H₆ (or C₁₀H₂₂) + NO + O₂ feed-flow reaction was tested, maximum NO reduction was below 30% over fresh Ag/Al₂O₃. After the addition of SO₂ to the feed flow, conversion increased slightly. Conversion increased further after SO₂ was cut-off from the feed flow. This demonstrated that the increase in NO reduction activity of the catalyst was related to SO_x adsorbed on the catalyst. SO_x adsorbed on the catalytic surface (1375 cm⁻¹) was detected by IR spectroscopy and was stable within the temperature range. NCO species, as an intermediate in NO reduction, on SO_x-adsorbed Ag/Al₂O₃ in a C₃H₆ + NO + O₂ feed flow was observed in in situ IR spectra during the elevation of the reaction temperature from 473 to 673 K, while it was only observed at 673 K on fresh Ag/Al₂O₃ under the same experimental conditions. We suggest that SO_x in low concentrations depressed the combustion of reductants by contaminating hydrocarbon combustion active sites on the catalyst, resulting in an increase in NO reduction efficiency of the reductants.     

Fourier transform infrared studies of cyclohexane and benzene adsorbed on Pt/Al2O3: Evidence for π- and σ-bonded chemisorbed species

Fourier transform infrared spectroscopy has been applied to the study of cyclohexane adsorbed on Al₂O₃ and Pt/Al₂O₃ surfaces. Earlier studies of benzene on these same materials have also been extended to include benzene adsorbed on a Pt/Al₂O₃ surface which contains structured carbon residues. The data provide indirect evidence for the formation of a carbon residue on Pt/Al₂O₃ which retains the six-membered cyclic structure of the parent adsorbates. The carbon residue can be formed upon vacuum heating of the parent C₆ ring molecules chemiorbed on Pt/Al₂O₃. There is spectroscopic evidence that cyclohexane dehydrogenates on Pt/Al₂O₃ at 300 K to form two different chemisorbed species; a π-bonded benzene and a dissociated σ-bonded benzene. These two chemisorbed species have CH stretching vibrations centered at 3030 and 2947 cm^?1, respectively. Benzene added to a clean catalyst surface forms only a π-bonded benzene. However, benzene added to Pt/Al₂O₃ with ordered carbon residues forms both π- and σ-bonded benzenes. The addition of H₂ at 300 K to any of the π- or σ-bonded benzenes or to the carbon residue results in the formation of cyclohexane physisorbed on the catalyst. The absence of CH₃ groups upon hydrogenation suggests the lack of CC bond breaking during adsorption or hydrogenation. Simultaneous infrared and thermal desorption studies on chemisorbed deuterated benzene (from C₆D₁₂) indicate that the a-bonded species exchange H from the surface OH groups of the alumina support more readily than does the π-bonded benzene. In addition to hydrogen exchange with the support, thermal desorption experiments indicate the oxidation of a portion of the chemisorbed hydrocarbons and/or carbon residue by oxygen from the alumina support. Therefore, the support is capable of playing a direct role in reactions occurring on the catalyst surface.     

Electrochemical solid electrolyte gas sensors — hydrocarbon and NOx analysis in exhaust gases

For the in situ measurement of the free oxygen concentration and the equilibrium oxygen partial pressure oxygen sensors based on zirconia solid electrolytes are widely used in order to monitor and control technical high temperature processes. Similarly combustibles (HC, CO) and NO_x can be determined in non equilibrated oxygen containing gas mixtures of exhausts by mixed potential sensors and amperometric solid electrolyte sensors. It is expected that their long-term stability is similar to that of oxygen sensors. In both cases the electrode material with the desired electrochemical and catalytic properties is the key component. Different electrode materials made of perovskites (La_1-xSr_xCr_1-yGa_yO_3-δ) and composites (Au/Metal oxide) were investigated in different combustibles including CO, C₃H_6/8, C₇H₈ and CH₄. The response behaviour of mixed potential sensors is determined by the catalytic activity of the measuring electrode, which is closely connected with the defect structure and depends on the measuring conditions. Furthermore the electrode response can be understood by electrokinetic data. Gas symmetrical mixed potential sensors with electrodes made of Au/Nb₂O₅ composites show maximum sensitivity. By using Ptreference electrodes without equilibrium behaviour the sensors are applicable in lean and rich mixtures as well. In the amperometric sensor mode the consecutive determination of oxygen and NO_x or combustibles at two working electrodes is possible. The catalytic activity of the oxygen pumping electrode should be low in order to avoid the decomposition of NO and HC respectively. Alternatively, the electrochemical reduction of NO can be performed at a single working electrode, made of materials with improved NO selectivity, without the previous reduction of oxygen. Paper presented at th 8th EuroConference on Ionics, Ixia, Rhodos, Greece, Sept. 15–21, 2002.     

Site-blocking effects of preadsorbed H on Pt(1 1 1) probed by 1,3-butadiene adsorption and reaction

The influence of hydrogen coadsorption on hydrocarbon chemistry on transition metal surfaces is a key aspect to an improved understanding of catalytic selective hydrogenation. We have investigated the effects of H preadsorption on adsorption and reaction of 1,3-butadiene (H₂CCHCHCH₂, C₄H₆) on Pt(1 1 1) surfaces by using temperature-programmed desorption (TPD) and Auger electron spectroscopy (AES). Preadsorbed hydrogen adatoms decrease the amount of 1,3-butadiene chemisorbed on the surface and chemisorption is completely blocked by the hydrogen monolayer (saturation) coverage (θ_H = 0.92 ML). No hydrogenation products of reactions between coadsorbed H adatoms and 1,3-butadiene were observed to desorb in TPD experiments over the range of θ_H investigated (θ_H = 0.6-0.9 ML). This is in strong contrast to the copious evolution of ethane (CH₃CH₃, C₂H₆) from coadsorbed hydrogen and ethylene (CH₂CH₂, C₂H₄) on Pt(1 1 1). Hydrogen adatoms effectively (in a 1:1 stoichiometry) remove sites from interaction with chemisorbed 1,3-butadiene, but do not affect adjacent sites. The adsorption energy of coadsorbed 1,3-butadiene is not affected by the presence of hydrogen on Pt(1 1 1). The chemisorbed 1,3-butadiene on hydrogen preadsorbed Pt(1 1 1) completely dehydrogenates to H₂ and surface carbon upon heating without any molecular desorption detected, which is identical to that observed on clean Pt(1 1 1). In addition to revealing aspects of site blocking that should have broad implications for hydrogen coadsorption with hydrocarbon molecules on transition metal surfaces in general, these results also provide additional basic information on the surface science of selective catalytic hydrogenation of butadiene in butadiene-butene mixtures.     

In situ controlled promotion of catalyst surfaces via solid electrolytes: Ethylene oxidation on Rh and propylene oxidation on Pt

The kinetics of C₂H₄ oxidation on Rh and C₃H₆ oxidation on Pt were investigated on polycrystalline metal films interfaced with ZrO₂(8mol%Y₂O₃) solid electrolyte in galvanic cells of the type:

Studies on partially oxidised one-dimensional bis(oxalato)platinate salts containing divalent cations

The preparation and electrical conduction properties of the isostructural one-dimensional conductors Ni_0.84[Pt(C₂O₄)₂]·6H₂O(Ni-OP) and Mn_0.81[Pt(C₂O₄)₂]·6H₂O(Mn-OP) are described. Ni-OP exhibits a similar tem dependence of conductivity to the isostructural compounds Co_0.83[Pt(C₂O₄)₂]·6H₂O(Co-OP) and Zn_0.81[Pt(C₂O₄)₂]·6H₂O whereas the behaviour of Mn-OP is rather like that of K₂[Pt(CN)₄]Br_0.3·3H₂O. These differences are discussed in terms of the variation from compound to compound of the critical temperature for the formation of the “non-Peierls” superstructure (T_c) and the temperature at which the CDW/PD on adjacent conducting chains undergo three-dimensional ordering (T_3D). The variation of thermopower with temperature for Co-OP and Mg_0.82[Pt(C₂O₄)₂]·6H₂O is reported and related to the conduction properties and phase changes which have been observed for these compounds. For the isostructural series M_0.8[Pt(C₂O₄)₂]·6H₂O (M = Mg, Mn, Co, Ni or Zn) the variation of (T_3D) from compound to compound is related to differences in the polarizing power of the cations.     

The role of co-adsorbed O2 on the catalytic reduction of NO with C2H5OH on the surface of Pt(3 3 2)

The influence of pre-dosed O₂ on the catalytic reduction of NO with ¹³C₂H₅OH on the surface of stepped Pt(3 3 2) was investigated using Fourier transform infra red reflection-absorption spectroscopy (FTIR-RAS) and thermal desorption spectroscopy (TDS). We show that the oxidation of ¹³C₂H₅OH with O₂ is a very effective reaction, occurring at 150 K and giving rise to acetate. The presence of NO does not lead to any evident oxidation of ¹³C₂H₅OH irrespective of the annealing temperature. For the case of O₂ + ¹³C₂H₅OH + NO co-adlayers, oxidation of ¹³C₂H₅OH also takes place at 150 K. However, no new surface species that are supposed to be an intermediate for the production of N₂ are detected.The influence of O₂ on the production and desorption of N₂ is intimately related to both O₂ and ¹³C₂H₅OH coverage. The presence of pre-dosed O₂ does not greatly promote N₂ desorption. In fact, N₂ desorption is suppressed quantitatively with increasing O₂ coverage, after which unreacted, or left-over O atoms appear and remain on steps. It is concluded that the presence of pre-dosed O₂ does not play a role of activating reactants in the catalytic reduction of NO with ¹³C₂H₅OH on the surface of Pt(3 3 2).     

Reactivity and XAFS study on (1−x)CeO2-xNiO (x=0.025-0.3) system in the two-step water-splitting reaction for solar H2 production

The redox reaction of Ce⁴⁺-Ce³⁺ promoted by the catalytic function of nickel ions in a (1−x)CeO₂-xNiO solid solution was investigated for solar H₂ production by the two-step water-splitting reaction. By irradiation using an infrared imaging lamp as a solar simulator, the O₂-releasing reaction with (1−x)CeO₂-xNiO solid solution proceeded at 1673-1873 K, and its reduced form was produced. The amounts of H₂ gas evolved by the reduced form were 1.2-2.5 cm³/g and the evolved gases amounts ratio of H₂/O₂ was nearly 2, which is equal to the stoichiometric value of the water-splitting reaction (H₂O=H₂+1/2O₂). The maximum amounts of evolved H₂ and O₂ gases were obtained at the Ce:Ni mole ratio of 0.95:0.05 (x=0.05) in the (1−x)CeO₂-xNiO system. The X-ray absorption fine structure (XAFS) measurement showed that the O₂-releasing and H₂-generation reactions with (1−x)CeO₂-xNiO solid solution were repeatable with the redox system of Ce⁴⁺-Ce³⁺, which was enhanced by the catalytic function of Ni²⁺-Ni⁰.     

Catalytic and electrocatalytic activation of methane over manganese oxides deposited on YSZ

The catalytic and the electrocatalytic behavior of MnO_x oxides deposited on Yttria Stabilized Zirconia (YSZ) in the form of thin porous films, was studied during the reaction of methane activation at high methane to oxygen ratios. Experiments were carried out in a continuous flow well-mixed reactor (CSTR), at atmospheric total pressure and in a temperature range between 500–850 °C. It was found that the electrochemical pumping of oxygen anions (O²⁻) through the solid electrolyte (YSZ) affect drastically the rates of CO₂, C₂H₄ and C₂H₆ formation and consequently the C₂ selectivity. Paper presented at the 4th Euroconference on Solid State Ionics, Renvyle, Galway, Ireland, Sept. 13–19, 1997     

Simultaneous removal of nitrogen oxides and diesel soot particulate in nano-structured electrochemical reactor

Simultaneous decomposition of nitrogen oxides (NO_x) and solid state graphite particles were carried out using a 8 mol% Y₂O₃ doped ZrO₂ (YSZ) based electrochemical reactor with a nano-structured NO_x selective multilayer cathode and an oxidative porous anode. The ceramic electrochemical cell was prepared by screen-printing a Pt and a NiO–YSZ pastes as cathode layers and a 12 CaO7Al₂O₃–Pt paste as an anode layer on the YSZ electrolyte, respectively. Simultaneous decomposition of NO_x and graphite particles was investigated using the cell with coated graphite particles on the surface of the 12 CaO7Al₂O₃–Pt composite anode in 1000 ppm NO_x–He gas flow under applying DC voltage at 475 °C. The coated graphite particles at the anode were removed completely with 80% NO_x decomposition by electrochemical reactions.     

Silica nanoparticles surface-modified with thiacalixarenes selectively adsorb oligonucleotides and proteins

In this study, platinum nanoparticles have been prepared using PtCl₄ as a starting material and 1-hexylamine, N-methylhexylamine, N,N-dimethylhexylamine, 1-heptylamine, N-methylheptylamine, and N,N-dimethylheptylamine as surfactants. All these surfactants were used in this synthesis, for the first time, to explore the effect of primary, secondary, and tertiary amine and chain length on the size and catalytic activity toward C1–C3 alcohol electro-oxidation. The electrochemical performance of all catalysts was determined using cyclic voltammetry and chronoamperometry. These techniques indicate that the highest electrocatalytic performance was generally observed when electrochemical surface area (ECSA), percent platinum utility, roughness factor, and the number of CH₃ groups attached to the nitrogen atom is higher and the chain length shorter (C₆H₁₃). In addition, other important properties such as the crystal structure of platinum, size, and distribution of the platinum nanoparticles on the carbon support, and Pt(0) to Pt(IV) ratio, were determined using X-ray photoelectron spectroscopy, X-ray diffraction, atomic force microscopy, and transmission electron microscopy. It was found that increasing ECSA, Pt(0)/Pt(IV) ratio, % Pt utility, and roughness factor improves the C1–C3 alcohol oxidation catalytic performance.     

Evaluation of the electrical capacitance of M,O2/O2− interfaces (M=Pt, Au, Pd, In2O3; O2− = zirconia based electrolyte) exhibiting constant phase element behavior

The behavior of the electrode systems M,O₂/O² (M = porous Pd, Pt, A and dense In₂O₃; O²⁻ = ZrO₂-based single-crystal solid electrolyte) was studied by means of impedance measurements. The examination of the Pt,O₂/O²⁻ electrode system showed that the constant phase element (CPE) can be attributed to a nonuniform distribution of current at the electrode surface. It was observed that the CPE parameters n and B in the expression Y_CPE = B (jω)ⁿ may be related by B=(C_dl)ⁿ (R_Ω)_n-1, where C_dl is the double layer capacitance and R_Ω the resistance of the electrolyte in the cell. Then, C_dl of the electrode - electrolyte interface could be determined. The specific C_dl of the oxidized noble metals and india electrodes is nearly one order of magnitude lower than C_dl of the electrodes in the metallic state. The C_dl value of all the electrodes studied depends little or is independent of temperature and oxygen pressure. It is concluded that the Helmholtz model of double layer structure does not contradict the C_dl behavior.     

Electrochemical promotion of electronically isolated and dispersed Pt catalysts

In this paper we discuss the first attempts to induce the effect of Electrochemical Promotion or Non-Faradaic Electrochemical Modification of Catalytic Activity (NEMCA) on highly dispersed catalyst-electrodes systems which can compete in terms of dispersion and surface area with industrial catalysts. Three systems are discussed:

1. Electrochemical promotion of C₂H₄ oxidation on electronically isolated Pt catalysts on Y₂O₃-stabilized-Zirconia (YSZ) where NEMCA is induced via potential application between two terminal Au electrodes also supported on the solid electrolyte (bipolar design).
2. Electrochemical promotion of C₂H₄ oxidation on a finely dispersed Pt catalyst deposited on a Au electrode which is supported on YSZ.
3. Induction of NEMCA during CH₃OH oxidation on Pt without external voltage application by utilizing the potential difference developed between the catalyst and a catalytically inert counter electrode.

In all cases significant non faradaic behavior has been obtained. The underlying catalytic/ electro-catalytic phenomena are discussed together with some of the engineering challenges for potential practical applications.     

Application of Black Pearl carbon-supported WO3 nanostructures as hybrid carriers for electrocatalytic RuSex nanoparticles

RuSe_x electrocatalytic nanoparticles were deposited onto hybrid carriers composed of Black Pearl carbon-supported tungsten oxide; and the resulting system's electrochemical activity was investigated during oxygen reduction reaction. The tungsten oxide-utilizing and RuSe_x nanoparticle-containing materials were characterized using transmission electron microscopy, X-ray diffraction and electrochemical diagnostic techniques such as cyclic voltammetry and rotating ring-disk voltammetry. Application of Black Pearl carbon carriers modified with ultra-thin films of WO₃ as matrices (supports) for RuSe_x catalytic centers results during electroreduction of oxygen in 0.5 mol dm⁻³ H₂SO₄ (under rotating disk voltammetric conditions) in the potential shift of ca. 70 mV towards more positive values relative to the behavior of the analogous WO₃-free system. Also the percent formation (at ring in the rotating ring-disk voltammetry) of the undesirable hydrogen peroxide has been decreased approximately twice by utilizing WO₃-modified carbon carriers. The results are consistent with the bifunctional mechanism in which oxygen reduction is initiated at RuSe_x centers and the hydrogen peroxide intermediate is reductively decomposed at reactive WO₃-modified Black Pearl supports. The electrocatalytic activity of the system utilizing WO₃-modified Black Pearl supports has been basically unchanged upon addition of acetic acid, formic acid or methyl formate to the sulfuric acid supporting electrolyte.     

Electrochemical activities of Pt-Ru-Co and Pt-Ru-Ni electrocatalysts supported by a carbon fiber web

Dynamic cyclic voltammetry is performed as functions of cycle number and potential window for the electrodeposition of Pt-Ru-Co and Pt-Ru-Ni catalysts on a carbon fiber (CF) web. Surface morphologies of the electrodeposited catalysts are observed by a scanning electron microscope. The electrochemical activity in methanol oxidation is examined by the cyclic voltammetry using a mixed aqueous solution of methanol as an electrolyte component. As the cycle number increases, both the current density and the amount of the electrodeposited metallic particles on the CF web are increased. The Pt-Ru-Ni/CF catalyst prepared in the potential range of −0.6 to 0.2 V and from the 1:2:2 mixed solution of H₂PtCl₆, RuCl₃·3H₂O, and Ni(NO₃)₂·6H₂O, respectively, shows the higher current density, corresponding to the higher catalytic activity.     

Density functional study of ethylene adsorption on small gold,palladium and gold-palladium binary clusters

Density functional theory calculations were performed to investigate the structural and energetic properties of chemisorbed Au _n -(C₂H₄) _x and Pd _n -(C₂H₄) _x complexes, with n = 2 ? 4 and x = 1 ? 4. Adsorption in π-bonded mode dominates in Au _n -(C₂H₄) _x species irrespective of x while the di-σ mode can be formed in the most stable Pd _n -(C₂H₄) _x species. The adsorption energy decreases as the number of C₂H₄ molecules increases in Au _n -(C₂H₄) _x with n ? 4 and Pd _n -(C₂H₄) _x with n ? 3. The adsorption of one C₂H₄ molecule on bimetallic Au/Pd clusters has also been studied. The C₂H₄ molecule prefers binding to Pd atoms in π-bonded configuration on Au/Pd clusters. The net charge transfer and the typical shift in the vibrational frequencies of C₂H₄ have also been determined and discussed.     

Electron impact ionisation cross section for organoplatinum compounds

This article reports electron impact ionisation cross sections for platinum-based drugs viz., cisplatin (H₆N₂Cl₂Pt), carboplatin (C₆H₁₂N₂O₄Pt), oxaliplatin (C₈H₁₄N₂O₄Pt), nedaplatin (C₂H₈N₂O₃Pt) and satraplatin (C₁₀H₂₂ClN₂O₄Pt) complexes used in the cancer chemotherapy. The multi-scattering centre spherical complex optical potential formalism is used to obtain the inelastic cross section for these large molecules upon electron impact. The ionisation cross section is derived from the inelastic cross section employing complex scattering potential–ionisation contribution method. Comparison is made with previous results, where ever available and overall a reasonable agreement is observed. This is the first attempt to report total ionisation cross sections for nedaplatin and satraplatin complexes.