Performance analysis of a swept-source optical coherence tomography system with a quadrature interferometer and optical amplification

A performance analysis of signal to noise ratio for an optical coherence tomography system with quadrature detection and a semiconductor optical amplifier in the sample arm is discussed. The results are compared and discussed in relation to a conventional OCT system (without optical amplification). An increase of the signal to noise ratio up to 14 dB at a depth of 0.5 mm is obtained compared to the system without the optical amplifier. Overall, an improvement was demonstrated for signal coming from deeper regions within the samples. Arterial plaque from a myocardial infarction-prone Watanabe heritable hyperlipidemic (WHHLMI) rabbit is visualized and characterized using this system. Improvement of signal to noise ratio increases the penetration depth possible for OCT images, from 1 mm to 2 mm within the vessel wall of an artery. Preliminary results show that vulnerable plaque with fibrous cap, macrophage accumulations and calcification in the arterial tissue are measurable with this OCT system.     

56 dB Gain EYDFA with improved noise figure with dual-stage partial double pass configuration

An efficient erbium/ytterbium co-doped fiber amplifier (EYDFA) is demonstrated by using a dual-stage partial double pass structure with a band pass filter (BPF). The amplifier achieves the maximum small signal gain of 56 dB and the corresponding noise figure of 4.66 dB at 1536 nm with an input signal power and total pump power of ?50 dBm and 140 mW, respectively. Compared with a conventional single-stage amplifier, the maximum gain enhancement of 16.99 dB is obtained at 1544 nm with the corresponding noise figure is improved by 2 dB. The proposed amplifier structure only uses a single pump source with a partial double pass scheme to provide a high gain and dual-stage structure to provide the low noise figure.     

Dual-stage L-band erbium-doped fiber amplifier with distributed pumping from single pump laser

A dual-stage L-band erbium-doped fiber amplifier with a flat gain bandwidth over 36 nm is demonstrated using pump distribution technique. The pump power was distributed to two stages depending on the splitting ratio and the length of erbium-doped fiber that was used for this configuration. Both parameters are the key components for achieving a substantially flat gain response throughout the L-band region ranging from 1570 nm to 1605 nm. Although the input signal power was varied from ? 30 dBm to 0 dBm, gain of 17 dB with slight variations of less than 1.5 dB and a noise figure of less than 6.7 dB were achieved. All the results obtained show better performances when comparison was made with the conventional single-stage L-band optical amplifier.     

A novel triple pump 1050 nm, 1400 nm, 800 nm pumping scheme for thulium doped fiber amplifier

Thulium doped fiber amplifier is a good candidate for S, and S+ band. This paper demonstrated a three pump pumping scheme for thulium doped fiber amplifier with 1050 nm co propagating pump and 1400 nm and 800 nm counter propagating pumps with a total pumping power 600 mW. This configuration yields up to 33 dB gain in 20 nm region from 1460 nm to 1480 nm, with noise figure <4 dB. To the knowledge of authors it is the highest gain achieved by thulium-doped amplifier in a single pass configuration with good power conversion efficiency.     

Inherently gain flattened S-band erbium doped fiber amplifier based on dual core resonant leaky fiber

A co-axial dual core resonant leaky optical fiber (DCRLF) is designed for inherent gain equalization of S-band erbium doped fiber amplifier (EDFA). Resonance tail of leakage loss of the fiber into the S-band region is utilized to flatten the gain. We have numerically studied the effect of various design parameters and their fabrication tolerances on gain flattening. We show 23.5 dB flat gain with ± 0.9 dB ripple over 30 nm bandwidth (1490–1520 nm) using 120 mW pump. The study should be useful in designing optical fiber amplifiers for optical communication system employing wavelength division multiplexing.     

High index contrast Er:Ta2O5 waveguide amplifier on oxidised silicon

We report a high index contrast erbium doped tantalum pentoxide waveguide amplifier. 2.3 cm long waveguides with erbium concentration of 2.7 × 10²⁰ cm^? 3 were fabricated by magnetron sputtering of Er-doped tantalum pentoxide on oxidised silicon substrates and Ar-ion milling with photolithographically defined mask. A net on-chip optical gain of ~ 2.25 dB/cm at 1531.5 nm was achieved with 20 mW of pump power at 977 nm launched into the waveguide. The pump threshold for transparency was 4.5 mW.     

Multiwavelength fiber ring laser using a gain clamped semiconductor optical amplifier

We demonstrate a novel multi-wavelength fiber ring laser based on a gain clamped semiconductor optical amplifier. The number of lasing lines can be tuned by adjusting the loss inside the cavity. The wavelength interval between the wavelengths is 100 GHz. The proposed laser shows a stable operation with total intensity fluctuation for a single laser line within ±0.02 dB at room temperature for a period of 30-minutes.     

Experimental and numerical investigation of the effect of a speed bump on car noise emission level

The noise emission level associated with two types of speed reducers has been investigated numerically and experimentally for different dimensions and different speeds of vehicle (20, 40 and 60 km/h) and zero acceleration. Numerical analysis has been performed using an FEM method in the ANSYS environment. The experiments show that for a bump of height 0.04 m, the peak noise level is increased by between 1 and 14 dB (A) whereas, for bump of height 0.055 m, the peak noise level increases by between 1 and 19 dB (A). There is an excellent agreement between the numerical and experimental results.     

High LO-to-RF isolation 94 GHz coplanar monolithic down-converter for FMCW radar sensor applications

This paper presents a 94 GHz monolithic down-converter with low conversion loss and high local oscillator (LO)-to-RF isolation using the 0.1 μm T-gate metamorphic high electron-mobility transistor (MHEMT) technology. The down-converter consists of a one-stage amplifier and a single-balanced mixer based on the high-directivity tandem coupler structure using the air-bridge crossovers, thereby amplifying the RF signals and maximizing the LO-to-RF isolation by using an inherent S₁₂ isolation characteristic of the amplifier and good phase balance of the tandem coupler. The fabricated one-stage amplifier using a 30 μm × 2 MHEMT shows a small signal gain of 7 dB at 94 GHz. The single-balanced mixer comprising two 20 μm × 2 MHEMT Schottky diodes and the tandem coupler with an additional λ/4-length line exhibits the conversion loss less than 7.8 dB and the LO-to-RF isolation higher than 30 dB in a RF frequency range of 91–96 GHz. Two circuits designed both for a 50 Ω impedance system are integrated into the down-converter of a 2.6 × 2.5 mm² chip size, and it shows a low conversion loss of ∼1 dB at 94 GHz and excellent LO-to-RF isolation above 40 dB in a frequency range of 90–100 GHz. This is the best isolation among the W-band monolithic down-converters reported to date.     

A miniaturized HTS microwave receiver front-end subsystem for radar and communication applications

This paper presents a miniaturized high performance high temperature superconducting (HTS) microwave receiver front-end subsystem, which uses a mini stirling cryocooler to cool a high selective HTS filter and a low noise amplifier (LNA). The HTS filter was miniaturized by using specially designed compact resonators and fabricating with double-sided YBCO films on LAO substrate which has a relatively high permittivity. The LNA was specially designed to work at cryogenic temperature with noise figure of 0.27 dB at 71 K. The mini cryocooler, which is widely used in infrared detectors, has a smaller size (60 mm × 80 mm × 100 mm) and a lighter weight (340 g) than the stirling cryocoolers commonly used in other HTS filter subsystem. The whole front-end subsystem, including a HTS filter, a LNA, a cryocooler and the vacuum chamber, has a size of only φ120 mm × 175 mm and a weight of only 3.3 kg. The microwave devices inside the subsystem are working at 71.8 K with a consumed cooling power of 0.325 W. The center frequency of this subsystem is 925.2 MHz and the bandwidth is 2.7 MHz (which is a fractional bandwidth of 0.2%), with the gain of 19.75 dB at center frequency and the return loss better than ?18.11 dB in the pass band. The stop band rejection is more than 60 dB and the skirt slope is exceeding 120 dB MHz^?1. The noise figure of this subsystem is less than 0.8 dB. This front-end subsystem can be used in radars and communication systems conveniently due to it’s compact size and light weight.     

High speed ultra short pulse fiber ring laser using photonic crystal fiber nonlinear optical loop mirror

A scheme to generate high speed optical pulse train with ultra short pulse width is proposed and experimentally studied. Two-step compression is used in the scheme: 20 GHz and 40 GHz pulse trains generated from a rational harmonic actively mode-locked fiber ring laser is compressed to a full width at half-maximum (FWHM) of ~ 1.5 ps using adiabatic soliton compression with dispersion shifted fibers (DSF). The pulse trains then undergo a pedestal removal process by transmission through a cascaded two photonic crystal fiber (PCF)-nonlinear optical loop mirrors (NOLM) realized using a double-ring structure. The shortest output pulse width obtained was ~ 610 fs for 20 GHz pulse train and ~ 570 fs for 40 GHz pulse train. The signal to noise ratio of the RF spectrum of the output pulse train is larger than 30 dB. Theoretical simulation of the NOLM transmission is conducted using split-step Fourier method. The results show that two cascaded NOLMs can improve the compression result compared to that for a single NOLM transmission.     

Gain flattening technique for optical wireless front-end receiver considering various large window photodetectors

A novel gain flattening technique for an optical wireless front-end receiver structure involving a bootstrap transimpedance amplifier (BTA) integrated with a MEMS variable feedback capacitor has been demonstrated. The MEMS varicap replaces a fixed capacitance as the feedback element in the front end system to optimize the performance of the BTA in terms of its frequency response. The implementation of the MEMS device with a BTA optical front-end receiver was verified using CoventorWare ARCHITECT. The simulation results showed that the approach can significantly flatten the peaking gain by up to 14 dB, when considering a system with various photodetector capacitances, ranging in value from 100 pF to 1 nF.     

PbS quantum dot fiber amplifier based on a tapered SMF fiber

A PbS quantum dot coated (QD-coated) tapered fiber amplifier with a broad bandwidth is theoretically demonstrated. The QD layer is coated on the surface of a tapered fiber and is excited by the evanescent wave of a pump. An optical gain of 10.5 dB, with a 160-nm broad bandwidth of at 1530-nm center wavelength, is achieved. The gain efficiency is over 4 dB/cm. This QD-tapered fiber amplifier has a concentration control of the QDs, a lower insertion loss, and shows good suppression of amplified spontaneous emission (ASE), while its structure is also quite simple. Therefore, the proposed fiber amplifier has great potential in fiber-optic communication systems.     

Performance evaluation of 64 × 10 Gbps and 96 × 10 Gbps DWDM system with hybrid optical amplifier for different modulation formats

In this paper, we investigated the performance of multi terabits DWDM system consisting of hybrid optical amplifier RAMAN-EDFA for different data format such as non-return to zero (NRZ), return to zero (RZ) and differential phase shift keying (DPSK). We find that in 64 × 10 and 96 × 10 Gbps, RZ is more adversely affected by nonlinearities, where as NRZ and DPSK is more affected by dispersion. We further show that RZ provide good quality factor (13.88 dB and 15.93 dB for 64 and 96 channels), less eye closure (2.609 dB and 3.191 dB for 64 and 96 channels) and acceptable bit error rate (3.89 × 10⁸ and 1.24 × 10⁹ for 64 and 96 channels) at the respective distance as compare to other existing modulation format. We further investigated the maximum single span distance covered by using existing data formats.     

Readout circuit with dual switching mode design for infrared focal plane arrays

The paper proposes a readout circuit architecture with adjustable integration time for dual-band infrared detectors. The readout circuit uses direct injection to be combined with a capacitive trans-impedance amplifier. The amplifier is sharing between two pixels to reduce the complexity of the readout circuit. The proposed device reduces power consumption and area overhead compared to traditional structures. An experimental chip was fabricated using the TSMC 0.35 μm 2P4 M 5 V process. The resulting unit pixel layout area is 40 μm × 40 μm with input photocurrent ranging from 0.11 pA to 50 nA. CTIA mode is applicable from 0.11 pA to 10 nA, while DI mode is applicable from 3.3 pA to 50 nA. The maximum operating frequency of the chip are 4 MHz. The CTIA output swing is 1.2 V, the DI output swing is 2 V. The signal to noise ratio of the readout circuit is 65 dB and power consumption is less than 9.6 mW.     

Novel optical add-drop multiplexer based on dual racetrack resonators

In this paper, we designed and fabricated a four-channel optical add-drop multiplexer (OADM) based on dual racetrack resonators. The size of the fabricated device is only 2400 μm × 500 μm. The fabricated device can effectively and perfectly realize the signals upload and download. The free spectral range (FSR) of OADM is about 15.2 nm. We take the spectral responses near 1555 nm as an example. When the device acts as an optical drop multiplexer, the minimum insertion loss is 4.481 dB and the maximum extinction ratio is 31.931 dB. The maximum adjacent channels crosstalk is -9.845 dB. When the device acts as an optical add multiplexer, the minimum insertion loss is 0.944 dB and all of the extinction ratios are bigger than 25 dB. The maximum crosstalk is -16.531 dB which indicates the crosstalk can be neglected.     

Performance analysis of optical network based on optical add drop multiplexers with different MZI techniques

This paper presents an investigation on the performance of an optical network in terms of crosstalk based on optical add drop multiplexers with Mach–Zehnder interferometer (MZI), MZI-semiconductor optical amplifier (SOA) and MZI-fiber Braggs gratings (FBG) techniques obtained at 8 × 10 Gbps with 0.1 nm channel spacing wavelength division multiplexing (WDM) transmission with optical add drop multiplexer (OADM) placed at the 20 km point of a 40 km link. It is found that the signal can be transmitted with least BER and better Q-factor with MZI-FBG based OADM and the worst case is found with the MZI-SOA based OADM.     

All-optical sampling exploiting nonlinear polarization rotation in a single semiconductor optical amplifier

An all-optical sampling scheme using a single semiconductor optical amplifier is proposed for analog signal processing. The analog optical signal is sampled by the probe pulse train through the nonlinear polarization rotation arising in the semiconductor optical amplifier. Conversion efficiency and total harmonic distortion are presented to evaluate the sampling linearity. In the experiment, 40 GSa/s all-optical sampling for 2.5 GHz analog optical signal is successfully demonstrated with commercially available fiber-pigtailed components. The results show that the fundamental conversion efficiency and the total harmonic distortion are 1.35 and 2.01% at the operating power of 5 mW, respectively. The proposed all-optical sampling requires only one semiconductor optical amplifier and has low power consumption, which is simple and has potential for photonic integration.     

Design of a super wide-band EM wave absorber for a general purpose anechoic chamber

In order to construct an anechoic chamber satisfying international standards for EMI testing, it has been recognized that the absorption characteristics of the EM wave absorber must be higher than 20 dB over the frequency band from 30 MHz to 18 GHz. In this paper, an EM wave absorber with super wide-band frequency characteristics is proposed and designed in order to satisfy the above requirements by using the EMCM and FDTD. As a result, the proposed absorber has absorption characteristics higher than 20 dB over the frequency band from 30 MHz to more than 20 GHz.     

A phase stable short pulse generator using a DPMZM and phase modulators for application in 160 GBaud DQPSK systems

A method of 40 GHz phase stable short pulses generation is experimentally demonstrated. It is based on a dual parallel Mach–Zehnder modulator (DPMZM) driven by only one electrical sinusoidal clock and two cascaded phase modulators. The generated pulses are characterized with full-width-at-half-maximum pulse width of 1.9 ps, extinction ratio of 27 dB, timing jitter of 36 fs and signal to noise ratio over 30 dB. The high quality and phase stability of the pulses are further experimentally verified in a 4 × 40 GBaud differential quadrature phase shift keying (DQPSK) optical-time-division-multiplexing (OTDM) system.