The use of a perylenediimide derivative as a dopant in hole transport layer of an organic light emitting device

A perylene diimide (PDI) derivative was used as a dopant in the hole transport layer (HTL) of an organic light emitting device. The HTL examined was poly (N-vinylcarbazole) (PVK) and the PDI used was N,N′-di-dodecylperylene-3,4,9,10-bis-(dicarboximide), (N-DODEPER). The structure of the device was ITO/PEDOT:PSS (70 nm)/PVK:N-DODEPER(0, 0.2, 0.4, 0.8 wt.%) (65 nm)/Alq₃ (35 nm)/LiF (1.3 nm)/Al (100 nm). 0.8 wt.% N-DODEPER presence exhibited a luminous efficiency of 7.87 cd/A and an external quantum efficiency of 0.78% at 21 mA/cm² and a power efficiency of 3l m/W at 12 mA/cm². The luminous and power efficiency values were significantly enhanced by a factor of 15 with respect to that of undoped device.     

Organic Light-Emitting Devices with a LiF Hole Blocking Layer

We introduce a thin LiF layer into tris-8-hydroxyquinoline aluminium （Alq3 ） based bilayer organic light-emitting devices to block hole transport. By varying the thickness and position of this LiF layer in Alq3, we obtain an electroluminescent efficiency increase by a factor of two with respect to the control devices without a LiF blocking layer. By using a 10nm dye doped Alq3 sensor layer, we prove that LiF can block holes and excitons effectively. Experimental results suggest that the thin LiF layer may be a good hole and exciton blocking layer.     

掺杂PEDOT ∶PSS对聚合物太阳能电池性能影响的研究

研究了掺杂后poly(3,4-ethylene dioxythiophene):poly(styrenesulphonic acid)(PEDOT ∶PSS)电导率的变化以及掺杂PEDOT ∶PSS薄膜对聚合物太阳能电池器件性能的影响. 实验发现,向PEDOT ∶PSS中掺入极性溶剂二甲基亚砜(DMSO)明显提高了薄膜的电导率,掺杂后的电导率最大值达到1.25 S/cm,比未掺杂时提高了3个数量级. 将掺杂的PEDOT ∶PSS薄膜作为缓冲层应用于聚合物电池 (ITO/PEDOT ∶PSS/P3HT ∶PCBM/LiF/Al) 中,发现高电导率的PEDOT ∶PSS降低了器件的串联电阻,增加了器件的短路电流,从而提高了器件的性能. 最好的聚合物太阳能电池在100 mW/cm²的光照下,开路电压(V_oc)为0.63 V,短路电流密度(J_sc)为11.09 mA·cm^-2,填充因子(FF)为63.7%,能量转换效率(η)达到4.45%. 关键词： PEDOT ∶PSS 电导率 聚合物太阳能电池 能量转换效率     

同时掺杂磷光和荧光染料的白色有机电致发光器件性能研究

以磷光染料Ir(piq)₂(acac)作为发光掺杂剂,掺入空穴传输性主体材料NPB中得到红色发光层,荧光材料TBP掺入到主体CBP中作为蓝色发光层,制备了结构为ITO/NPB/NPB：Ir(piq)₂(acac)/CBP/CBP：TBPe/BCP/ALq/Mg：Ag的双发光层白色有机电致发光器件.其中ALq₃、未掺杂的NPB和CBP及BCP层分别作为电子传输层、空穴传输层和激子阻挡层.实验中通过调节发光层厚度及Ir(piq)_{2关键词： 磷光 激子阻挡层 有机电致发光}     

White organic light-emitting diodes based on combined electromer and monomer emission in doubly-doped polymers

We report on white organic light-emitting diodes (WOLEDs) based on polyvinylcarbazole (PVK) doped with 1,1-bis((di-4-tolylamino)phenyl)cyclohexane (TAPC) and perylene, and investigate the luminescence mechanism of the devices. The chromaticity of light emission can be tuned by adjusting the concentration of the dopants. White light with the Commission Internationale de L'Eclairage (CIE) coordinates of (0.33, 0.34) is achieved by mixing the yellow electromer emission of TAPC and the blue monomer emission of perylene from the device ITO/PVK: TAPC: perylene (100:9:1 in wt.) (100 nm)/tris-(8-hydroxyquinoline aluminum (Alq₃) (10 nm)/Al. The device exhibits a maximal luminance of 3727 cd/m² and a current efficiency of 2 cd/A.     

Highly efficient and stable organic light-emitting diode by balancing drift current of charge

Highly efficient and stable OLED device in which hole-drift current and electron-drift current are balanced was fabricated. Drift current characteristics according to the thickness of organic layer were examined using the device with ITO/m-MTDATA/NPB/Al structure that can only move the hole and the device with Al/LiF/Alq₃/LiF/Al structure that can only move the electron. Using the result of such examination, green device with balanced drift current was produced. Device with the structure of m-MTDATA (80 nm)/NPB (20 nm)/C-545T (3%) doped Alq₃ (5 nm)/Alq₃ (59 nm)/LiF (1 nm)/Al (200 nm) showed color purity of (0.309, 0.643) and high efficiency of 7.0 lm/W (14.4 cd/A). Most of light emission was observed inside the green emitting layer. Through the result of EL spectrum for the device also including red emitting layer, same result could be obtained. The device with balanced drift current also showed half life-time of 175 h for initial luminance of 3000 cd/m², which is more stable in comparison to the device without balanced drift current.     

Spectral studies of thin films based on poly(N-vinylcarzole) and red dopant

Organic light-emitting diodes were fabricated with a structure of indium-tin-oxide (ITO)/poly(N-vinylcarzole)(PVK):4-(dicyanom-ethylene)-2-t-butyl-6-(1,1,7,7-tetramethyljulolidyl-9-enyl)-4H-pyran (DCJTB)/8-tris-hydroxyquinoline aluminum (Alq₃)/lithium fluoride (LiF)/Al. The energy transfer from PVK to Alq₃ then to DCJTB and the charge trapping processes were investigated by employing the photoluminescence (PL) and electroluminescence (EL) spectra. With increasing thickness of the Alq₃ layer, the PL and EL emission from PVK were decreased gradually, which indicated that the effective energy transfer occurred from PVK to Alq₃ and then from Alq₃ to DCJTB. At the same time, we found that the exciton recombination zone could be adjusted by controlling the Alq₃ layer thickness and the applied voltages. The effects of different DCJTB concentrations on the optical and electrical characteristics of the devices were investigated, and an obvious red-shift was observed with the DCJTB dopant concentrations increasing in the PL and EL spectra.     

The effect of Ag layer thickness on the properties of WO3/Ag/MoO3 multilayer films as anode in organic light emitting diodes

Transparent conductive WO₃/Ag/MoO₃ (WAM) multilayer electrodes were fabricated by thermal evaporation and the effects of Ag layer thickness on the optoelectronic and structural properties of multilayer electrode as anode in organic light emitting diodes (OLEDs) were investigated using different analytical methods. For Ag layers with thickness varying between 5 and 20 nm, the best WAM performances, high optical transmittance (81.7%, at around 550 nm), and low electrical sheet resistance (9.75 Ω/cm²) were obtained for 15 nm thickness. Also, the WAM structure with 15 nm of Ag layer thickness has a very smooth surface with an RMS roughness of 0.37 nm, which is suitable for use as transparent conductive anode in OLEDs. The current density?voltage?luminance (J?V?L) characteristics measurement shows that the current density of WAM/PEDOT:PSS/TPD/Alq₃/LiF/Al organic diode increases with the increase in thickness of Ag and WO₃/Ag (15 nm)/MoO₃ device exhibits a higher luminance intensity at lower voltage than ITO/PEDOT:PSS/TPD/Alq₃/LiF/Al control device. Furthermore, this device shows the highest power efficiency (0.31 lm/W) and current efficiency (1.2 cd/A) at the current density of 20 mA/cm², which is improved 58% and 41% compared with those of the ITO-based device, respectively. The lifetime of the WO₃/Ag (15 nm)/MoO₃ device was measured to be 50 h at an initial luminance of 50 cd/m², which is five times longer than 10 h for ITO-based device.     

Bright electrophosphorescent devices based on sterically hindered spacer-containing Cu(I) complex

A Cu(I) complex, [Cu(Dppp)(DPEphos)]BF₄ (Dppp=2,3-diphenyl-pyrazino[2,3-f][1,10]phenanthroline, DPEphos=Bis[2-(diphenylphosphino)phenyl]ether), is synthesized and used as the dopant in bright electrophosphorescent devices with the general structure ITO/m-MTDATA (30 nm)/NPB (20 nm)/CBP: ×wt% [Cu(Dppp)(DPEphos)]BF₄ (30 nm)/Bphen (20 nm)/Alq₃ (20 nm)/LiF (0.8 nm)/ Al (200 nm). These devices exhibit a maximum brightness of 4483 cd/m² and a peak efficiency of 3.4 cd/A. Compared with previously reported similar devices based on Cu(I) complexes, the brightness of the devices presented in this article is the best. Meanwhile, 2% [Cu(Dppp)(DPEphos)]BF₄-based devices exhibit white light-emitting properties with CIE coordinates of (0.32. 0.35) at 10 V.     

4,4′,4″-三(N-3-甲基苯基-N-苯基氨基)三苯胺掺杂MoOx作为空穴传输层对有机太阳电池性能的影响

通过采用4,4′,4″-三(N-3-甲基苯基-N-苯基氨基)三苯胺 (m-MTDATA)掺入MoO_x作为器件的空穴传输层来提高酞菁铜(CuPc)/C₆₀小分子 有机太阳电池的效率. 采用真空蒸镀的方法制备了一系列器件, 其中结构为铟锡氧化物 (ITO)/m-MTDATA:MoO_x(3:1)(30 nm)/CuPc(20 nm)/C₆₀(40 nm)/4,7-二苯 基-1,10-菲罗啉 (Bphen)(8 nm)/LiF(0.8 nm)/Al(100 nm)的器件, 在AM1.5 (100 mW/cm²)模拟太阳光的照射条件下, 开路电压V_oc=0.40 V, 短路电流J_sc=6.59 mA/cm², 填充因子为0.55, 光电转换效率达1.46%, 比没有空穴传输层的器件ITO/CuPc(20 nm)/C₆₀(40 nm)/Bphen(8 nm)/LiF(0.8 nm)/Al(100 nm) 光电转换效率提高了38%. 研究表明, 加入m-MTDATA:MoO_x(3:1)(30 nm)空穴传输层减小了有机层和ITO电极之间的接触电阻, 从而减小了整个器件的串联电阻, 提高了器件的光电转换效率.     

Efficient and low potential operative host/guest concentration graded bilayer polymer electrophosphorescence devices

This study investigates enhanced electrophosphorescence and its mechanism in poly(N-vinyl carbazole) (PVK): N,N′-diphenyl-N,N′-bis(3-methylphenyl)-[1,1-biphenyl]-4,4′-diamine (TPD)/2-(4-biphenylyl)-5-(4-tert-butylphenyl)-1,3,4-oxadiazole (PBD): fac-tris(2-phenylpyridine)iridium [Ir(ppy)₃] concentration graded bilayer electroluminescence devices. The two layers are partially intermixed at the bilayer interface because the upper layer (composed of Ir(ppy)₃ and PBD) was spun cast from a solvent that slightly swells the bottom layer (composed of PVK and TPD). Moreover, PBD in the upper layer can act as an efficient electron transport layer as well as a hole blocking layer, resulting in greatly enhanced electron–hole recombination. An indium tin oxide (ITO)/3,4-polyethylenedioxythiophene–polystyrenesulfonate (PEDOT)/[PVK:TPD/Ir(ppy)₃:PBD] bilayer/LiF/Al device showed dramatically decreased turn-on and driving voltages, enhanced luminescence efficiency, and narrower emission spectra compared to those of conventional ITO/PEDOT:PSS/[PVK:TPD:Ir(ppy)₃:PBD] blend/LiF/Al devices.     

新型苯乙烯衍生物掺杂的蓝色及白色有机电致发光器件

研究了新型高效蓝色掺杂剂EBDP的电致发光性能. 分别以EBDP为掺杂剂制备了结构为氧化铟 锡(ITO)/酞菁铜(CuPc)/N,N′-二(1-萘基)-N,N′-二苯基-1,1′-联苯-4-4′-二胺(NPB)/2- 叔丁基-9,10-二-(2-萘基)蒽(TBADN):EBDP/8-羟基喹啉铝(Alq₃)/LiF/Al 与ITO /CuPc/NPB/TBADN:EBDP: 4-二氰亚甲基-2-叔丁基-6-(1,1,7,7-四甲基久咯呢定基-9-烯基)- 4H-吡喃/Alq_{3 关键词： 有机电致发光 蓝色掺杂剂 蓝色电致发光器件 白色电致发光器件}     

The roles of zinc selenide sandwiched between organic layers and its applications in white light-emitting diodes

In this paper, the roles of zinc selenide (ZnSe) sandwiched between organic layers, i.e. organic/ZnSe/aluminum quinoline (Alq₃), have been studied by varying device structure. A broad band emission was observed from ITO/poly(N-vinylcarbazole)(PVK)(80 nm)/ZnSe(120 nm)/ Alq₃(15 nm)/Al under electric fields and it combined the emissions from the bulk of PVK, ZnSe and Alq₃, however, emission from only Alq₃ was observed from trilayer device ITO/N,N^′-bis-(1-naphthyl)-N,N^′-diphenyl-1, 1^′-biphenyl-4, 4^′-diamine (NPB) (40 nm)/ZnSe(120 nm)/ Alq₃(15 nm)/Al. Consequently the luminescence mechanism in the ZnSe layer is suggested to be charge carrier injection and recombination. By thermal co-evaporating Alq₃ and 4-(dicyanomethylene)-2-t-butyl-6-(1,1,7,7-tetramethyljulolidyl-9-enyl)-4H-pyran (DCJTB), we get white light emission with a Commission Internationale de l’E clairage (C.I.E) co-ordinates of (0.32, 0.38) from device ITO/PVK(80 nm)/ZnSe(120 nm)/ Alq₃:DCJTB(0.5 wt% DCJTB)(15 nm)/Al at 15 V and the device performs stably with increasing applied voltages.     

High-efficiency Simple Structure White Organic Light-emitting Devices Based on Rubrene Ultrathin Layer

White organic light-emitting devices (WOLEDs) were fabricated with an ultrathin layer of rubrene inserted between NPB and TPBI. With a simple three-layer structure of ITO/NPB(50 nm)/rubrene(0.1 nm)/TPBI(50 nm)/LiF/Al, a white light with CIE coordinates of (0.31, 0.30) were generated. The device gave a maximum luminance efficiency of 2.04 lm/W at 5 V. Furthermore, with a multilayer structure of ITO/m-MTDATA(30 nm)/NPB(20 nm)/rubrene(0.1 nm)/TPBI(40 nm)/Alq₃(10 nm)/LiF/Al, the device reached a maximum luminance efficiency of 4.29 lm/W at 4 V and the luminance could exceed 10 000 cd/m² at 10 V.     

Investigation of an efficient YbF3/Al cathode for tris-(8-hydroxyquinoline)aluminum-based small molecular organic light-emitting diodes

Efficient tris-(8-hydroxyquinoline)aluminum (Alq₃)-based organic light-emitting diodes (OLEDs) using YbF₃ as the electron injection layer have been investigated. With an YbF₃ (3.0 nm)/Al cathode, the device with Alq₃ as the emitting layer achieved a better performance than the control device with a LiF (0.5 nm)/Al cathode. The release of the low-work-function metal Yb is responsible for the performance enhancement. From the analysis by atomic force spectroscopy and X-ray photoemission spectroscopy, it is observed that the Alq₃-cathode interface could be well covered by YbF₃ at an optimum thickness of 3.0 nm, which helps to prevent the contact between Alq₃ and Al, and to reduce the destruction of Alq₃ by Al.     

Blue organic light-emitting diodes with low driving voltage and maximum enhanced power efficiency based on buffer layer MoO3

Blue organic light-emitting devices based on wide bandgap host material, 2-(t-butyl)-9, 10-di-(2-naphthyl) anthracene (TBADN), blue fluorescent styrylamine dopant, p-bis(p-N,N-diphenyl-amino-styryl)benzene (DSA-Ph) have been realized by using molybdenum oxide (MoO₃) as a buffer layer and 4,7-diphenyl-1,10-phenanthroline (BPhen) as the ETL. The typical device structure used was glass substrate/ITO/MoO₃ (5 nm)/NPB (30 nm)/[TBADN: DSA-Ph (3 wt%)](35 nm)/BPhen (12 nm)/LiF (0.8 nm)/Al (100 nm). It was found that the MoO₃∥BPhen-based device shows the lowest driving voltage and highest power efficiency among the referenced devices. At the current density of 20 mA/cm², its driving voltage and power efficiency are 5.4 V and 4.7 Lm/W, respectively, which is independently reduced 46%, and improved 74% compared with those the m-MTDATA∥Alq₃ is based on, respectively. The J-V curves of ‘hole-only’ devices reveal that a small hole injection barrier between MoO₃∥NPB leads to a strong hole injection, resulting low driving voltage and high power efficiency. The results strongly indicate that carrier injection ability and balance shows a key significance in OLED performance.     

Enhanced performance of light-emitting diodes based on a nanocomposite of dehydrated nanotube titanic acid and poly(vinylcarbazole) (PVK)

Performance of light-emitting diodes (LEDs) based on a nanocomposite of dehydrated nanotube titanic acid (DNTA) and poly(vinylcarbazole) (PVK) as emissive layer, i.e., ITO/PVK:DNTA(2 wt%)(100 nm)/BCP(30 nm)/Alq₃(10 nm)/LiF(1 nm)/Al [device D₂], was reported. By investigation of the luminance and electric characteristics of the device, we found that the performance of device D₂ was greatly improved. The recombination zone changed evidently due to the improvement of holes mobility. Compared with those devices without incorporating DNTA, both the maximum luminance and the electroluminescent efficiency of the device D₂ can be improved by a factor of three. Furthermore, the turn-on voltage of the device decreased dramatically.     

Reduction of driving voltage in organic light-emitting diodes with molybdenum trioxide in CuPc/NPB interface

A novel structure of organic light-emitting diode was fabricated by inserting a molybdenum trioxide (MoO₃) layer into the interface of hole injection layer copper phthalocyanine (CuPc) and hole transport layer N,N′-diphenyl-N,N′-bis(1-napthyl-phenyl)-1,1′-biphenyl-4,4′-diamine (NPB). It has the configuration of ITO/CuPc(10 nm)/MoO₃(3 nm)/NPB(30 nm)/ tris-(8-hydroxyquinoline) aluminum (Alq₃)(60 nm)/LiF(0.5 nm)/Al. The current density-voltage-luminance (J-V-L) performances show that this structure is beneficial to the reduction of driving voltage and the enhancement of luminance. The highest luminance increased by more than 40% compared to the device without hole injection layer. And the driving voltage was decreased obviously. The improvement is ascribed to the step barrier theory, which comes from the tunnel theory. The power efficiency was also enhanced with this novel device structure. Finally, “hole-only” devices were fabricated to verify the enhancement of hole injection and transport properties of this structure.     

使用PTB7作为阳极修饰层提高有机发光二极管的性能

采用poly[[4,8-bis[(2-ethylhexyl)oxy]benzo[1,2-b:4,5-b’]dithiophene-2,6-diyl][3-?uoro-2-[(2-ethylhexyl)carbonyl]thieno[3,4-b]thiophenediyl]](PTB7)作为有机发光二极管器件的阳极修饰层,制备了结构为indium tin oxide(ITO)/PTB7(不同浓度)/N,N’-Bis(naphthalen-1-yl)-N,N’-bis(phenyl)benzidine(NPB,40 nm)/8-hydroxyquinoline(Alq3,60 nm)/LiF(1 nm)/Al的系列器件,同时研究了不同浓度的PTB7对器件性能的影响.PTB7的最佳浓度为0.25 mg/mL,器件性能得到明显的改善,起亮电压为4.3 V.当驱动电压为14.6 V时,最大亮度为45800 cd/m2,最大电流效率为9.1 cd/A.与没有PTB7修饰的器件相比,其起亮电压降低了1.9 V,最高亮度提升了78.5%.器件性能提高归因于PTB7的插入使得空穴注入和传输能力大大改善.     

ZnSe(ZnS)纳米晶与MEH-PPV的共掺有机电致发光器件

采用水相法合成核壳结构ZnSe/ZnS 纳米晶,经X射线衍射(XRD)分析和透射电子显微镜(TEM)表征,证实所制备的样品为立方晶型闪锌矿结构ZnSe/ZnS量子点。按照一定的质量比将ZnSe/ZnS 纳米晶和有机聚合物MEH-PPV(poly ) 共掺并将其作为发光层,分别制备单层和多层有机电致发光器件,结构为ITO/MEH-PPV∶ZnSe(ZnS)(50 nm)/Al和 ITO/PEDOT∶PSS(70 nm)/ MEH-PPV∶ZnSe(ZnS)(50 nm)/BCP(15 nm)/Alq₃(12 nm) /LiF(0.5 nm)/Al。实验结果表明,多层发光器件的发光特性与单层器件不同,工作电压的增大使其发光峰发生了明显的蓝移。