Tunneling conductance of a Bi2−xPbxSr2Ca2Cu3O10−y-SnO2 junction

Fine structures were observed in the tunneling conductance of a sintered Bi 2223-SnO₂ junction. The structures are weaker than those of a single crystalline Bi2212. They correspond to the Raman spectrum of Bi2223 and approximately to the phonon density of states of Bi2212. The structures must therefore be phonon structures, and phonons may contribute substantially to highT _c superconductivity. Multiphonon structures are scarcely discernible. Hence we propose a new model, in place of the prior multiphonon model, to explain the rapid increase inT _c with the CuO₂ layer number. 2 (21 K)=68±4 meV inT _c=98±5 K. 2 (0)/k _B T _c is 8.1±0.9. The temperature dependence of the gap was also observed and discussed.     

A computational study of the electron detachment energies of Al2As2 − and Al3As3 −

Ab initio and density functional theory calculations are reported for the low-lying electronic states of Al₂As₂ ^?, Al₂As₂, Al₃As₃ ^?, and Al₃As₃. The ²B_2g ground electronic state of Al₂As₂ ^? has a rhombic structure with the Al atoms occupying the shorter diagonal. In contrast, the As atoms occupy the shorter diagonal of the ground state rhombic structure of Al₂As₂. Electron detachment energies computed for Al₂As₂ ^? are presented and discussed. The adiabatic electron affinity of Al₂As₂ ^? is calculated to be 2.1 eV at the CCSD(T) level, using B3LYP and MP2 optimized geometries. The ground states of both Al₃As₃ ^? (²A₁′) and Al₃As₃ (¹A₁′) have planar hexagonal D_3h geometry. Electron detachment energies computed for the anion are reported. At the CCSD(T)//B3LYP level, the electron affinity of Al₃As₃ is calculated to be 2.47 eV.     

Phase transitions in La1−x CaxMnO3−x/2 manganites

The crystal structure parameters and magnetic and electrical properties of La_1?x Ca_xMnO_3?x/2 reduced manganites with 0≤x≤0.5 are established. These investigations contribute to the understanding of magnetic interactions in manganites without Mn⁴⁺ ions. It is found that these manganites show a long-range antiferromagnetic order up to x=0.09 and transform into spin glasses at 0.09<x≤0.35. The compositions in the range 0.35<x≤0.5 show a strong increase in the spontaneous magnetization and critical point associated with the appearance of spontaneous magnetization and can therefore be viewed as inhomogenious ferromagnets. The magnetic and crystal structure peculiarities of La_0.5Ca_0.5MnO_2.75 are established by the neutron diffraction method. The strongly reduced samples show a large magnetoresistance below the point where the spontaneous magnetization develops. The magnetic phase diagram of La_1?x Ca_xMnO_3?x/2 is established by magnetization measurements. The magnetic behavior is interpreted assuming that the Mn³⁺-O-Mn³⁺ magnetic interaction is anisotropic (positive-negative) in the orbitally ordered phase and isotropic (positive) in the orbitally disordered phase. Introduction of the oxygen vacancies changes the magnetic interaction sign from positive to negative, thereby leading to a spin glass state in strongly reduced compounds. The results obtained reveal unusual features of strongly reduced manganites such as a large ferromagnetic component, a high magnetic ordering temperature, and a large magnetoresistance despite the absence of Mn³⁺-Mn⁴⁺ pairs. In order to explain these results, the oxygen vacancies are supposed to be ordered.     

Factors determining the energy yield of luminophors based on single-crystal films of Al2−Y2O3−R2O3 oxides

We consider the factors determining the energy yield of crystallophosphors based on single-crystal films of oxides of the system Al₂−Y₂O₃−R₂O₃ (R is the rare-earth ions) that are used as different types of luminescent converters. Special features of producing the films by the method of liquid-phase epitaxy from Pb−B₂O₃ and Bi₂O₃-based fluxes are analyzed, and the advantages of this method for production of efficient luminophors, which are based on high-melting oxides doped with mercury-like impurities, are shown. It is established that the main factor that bounds the crystallophosphor luminous yield is the presence of donor-acceptor complexes of the Pb²⁺−Pb⁴⁺ and Fe³⁺−Fe²⁺-type that form different channels of dissipation of excitation energy. The means of minimizing the contribution of these ions to the processes of excitation-energy relaxation are discussed. Institute of Applied Physics, I. Franko L'vov State University, 49 General Chuprynka Str., L'vov, 290044, Ukraine. Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 66, No. 6, pp. 819–823, November–December, 1999.     

Infrared spectra of superconducting La2−xSrxCuO4 and YBa2Cu3O7−δ

Abstract

Abstract Infrared spectra of La_2?xSr_xCuO₄ and YBa₂Cu₃O_7?δ are discussed, specially with respect to the disappearance of the high-frequency (～650 cm) band of the superconducting compositions at 300K. Some of the bands persist at 300K eventhough the materials are fairly conducting. YBa₂Cu₃O_7?δ does not show evidence in the far IR spectrum for the presence of an optical gap.     

Optical properties of Li1−xNb1−xEu2xO3 solid solutions

Abstract

The effects of europium substitution on crystalline solubility, structural changes and optical properties of LiNbO₃ is reported. Li_1?xNb_1?xEu_2xO₃ solid solutions exist over a very limited range of europium concentrations (x ≤ 0.01). The solid solutions were characterized by X-ray powder diffraction and density measurements. Within the range of compositions of the solid solutions, the optical properties (emission and excitation spectra) of the Eu³⁺ ions have been characterized. The obtained optical data indicate that two equally abundant europium luminescent species exist in the stoichiometric speciments; these correspond to the Eu³⁺ ions occupying the Li⁺ and Nb⁵⁺ sites, in agreement with the replacement mechanism which is inferred from density measurements. Other Eu³⁺ luminescent species which appear to be closely related with lithium deficiency were found to exist in nonstoichiometric samples, in addition to those which are present in the stoichiometric materials.     

Al,F-doped new perovskite lithium fast ion conductor Li3x La2/3−x□1/3−2x Ti1−y Al y O3−y F y (x=0.11)

Al, F-doped new perovskite lithium ion conductors (x=0.11) have been prepared by solid state reaction. It is found that a pure perovskite-structured phase with space group of P4mm(99) exits in the composition range of 0<y≤0.10. The sample with y=0.02 possesses the highest ionic conductivity of 1.06×10⁻³ S/cm at room temperature, and its decomposing voltage is 2.3 V. The factors affecting the conductivity of this system are discussed.     

ВЛИЯНИЕ СОДЕРЖАНИЯ К ИСЛОРОДА НА ЭЛЕКТРИЧЕСКИЕ И ТЕ РМОЭЛЕКТРИЧЕСКИЕ СВОЙСТВА ТРОЙНОЙ СИС ТЕМЫ Вi2Те3−x Sе x

, Bi₂Te_3–x Se _x . , , . , , . .

---

Influence of oxygen content on electric and thermoelectric properties of ternary system Bi₂Te_3–x Se _x

A study is made of the influence of oxygen, contained in the semi-conducting system Bi₂Te_3–x Sé _x , on the electric and thermoelectric properties. It is shown that the addition of oxygen to the prepared samples Bi₂Te_2.4Se_0.6 causes a decrease in electric conductivity while the thermoelectric force remains unchanged. This influence is connected with a decrease in the mobility of the electrons but their concentration is not influenced by the presence of oxygen. Conclusions are reached as to the influence of oxygen on the efficiency of the conversion of thermal energy into electric energy and vice versa.

     

Relaxation phenomena in Cr3+ doped Al2O3−Fe 2 57 O3 systems

Mössbauer absorption spectra have been measured for Cr³⁺ doped Al₂O₃?Fe ₂ ⁵⁷ O₃ systems for different values of the Cr³⁺ concentration at room temperature. The cross relaxation between Fe³⁺ and Cr³⁺ ions, which destroys the paramagnetic hyperfine structure of Fe⁵⁷ observed in undoped Al₂O₃?Fe ₂ ⁵⁷ O₃, is thoroughly studied. The experimental results suggest a new kind of cross-relaxation process involving three spins, i.e. two Fe³⁺.ions and one Cr³⁺. The process, though it is a higher-order one, is highly effective because it is energy-conserving.     

The hole concentration on oxygen sites in the highT c superconductor Y1−Ba2−Cu3−O7−x

From XPS core level spectroscopy the average copper charge on the Cu sites in the high temperature superconductor Y₁Ba₂Cu₃O_7–x is determined as function of the oxygen vacancy concentrationx. Analysis of these data leads to the suggestion that there are holes on the oxygen sites in the basal plane of the crystal structure. The probability for holes on these oxygen ions is rather constant for 0x0.3 with a value of 0.64 and decreases to zero forx=0.5. The dependence of the superconducting transition temperature on the hole concentration is discussed. An energy level diagram for Cu²⁺ and Cu³⁺ in YBa₂Cu₃O_7–x is constructed.     

Europium-doped nanocrystalline Y2O3−La2O3 solid solutions with bixbyite structure

Nanocrystals of Y₂O₃ and La₂O₃ solid solutions were synthesized with a cubic bixbyite structure containing La₂O₃ content of up to 50 mol%. This is comparatively higher than that in bulk materials of the same structure, where La₂O₃ content of only 20 mol% can be obtained. A set of europium-doped (Y_1−xLa_x)₂O₃ (x=0.1, 0.2, 0.3, 0.4) cubic bixbyite solid solutions with crystallites of approximately 10 nm in size was prepared using the polymer complex solution method. Structural analysis was performed using X-ray diffraction measurements, Rietveld full profile refinement, and from Eu³⁺ luminescence emission. The energy levels of the Eu³⁺ ion, second order crystal field parameters, and crystal field strength were obtained for all compositions of solid solutions. We show that the crystal field parameters linearly depend on unit cell parameter and that these dependencies may be considered as part of an overall dependence for the entire sesquioxide family.     

Influence of CO 3 2− and OH− groups on dielectric losses of NaCl crystals

The results of measuring the dielectric losses of NaCl crystals with a different concentration of Na₂CO₃ and NaOH admixtures in the melt are given in the present paper. From a comparison of the curves found for the dielectric losses of the crystals studied it can be seen that the course of tan and the positions of the relaxation maxima, corresponding to the measured specimens with CO ₃ ^2– or OH^– admixtures, hardly differ. From these measurements and from a comparison with the results of other authors it follows that the admixture is probably the same in both groups of crystals.In conclusion the author thanks Dr. A. Bohun for discussions on the results and for his continuous interest in this work.     

Synthesis and ionic conduction of C3A-type nasicon Na3+3x−yY1−xSi3−yPyO9

In the solid solutions of Na_3+3x−yY_1−xSi_3−yP_yO₉, new fast Na⁺ -conductors were obtained. The ionic conductivity, σ, and the activation energy, E, of the most conductive material, Na_4.425Y_0.375Si_2.55P_0.45O₉ were 5 × 10⁻³ S/cm at 300°C and 10 kcal/mol, respectively. Those values were strongly dependent upon the composition. With an increase of Na concentration, [Na], σ increased and E decreased. Accommodation of higher [Na] in the structure was madefeasible by decreasing [Y] and increasing [P]. Based on the crystal structure assumed for Na_3+3x−yY_1−xSi_3−yP_yO₉ and on the above results, a conduction model was presented. The structural consideration revealed that a conduction path is formed along the 〈1 1 1 〉 direction, where Y³⁺ ions locate in the way of Na⁺ ions.     

Assessment of role of iron ions on the physical and spectroscopic properties of multi-component Na2O−PbO−Bi2O3−SiO2 glass ceramics

Multi-component glass ceramics composition Na₂O?PbO?Bi₂O₃?SiO₂ doped with different concentrations of Fe₂O₃ as nucleating agent were characterised by XRD, SEM (scanning electron microscope) and DTA (differential thermal analysis) techniques. Optical absorption, EPR, FTIR and Raman studies are also carried out on these glass ceramics. Absorption bands observed at about 457, 489, 678 and 820 nm are the characteristics of Fe³⁺ ions whereas the band observed at about 964 nm is due to Fe²⁺ ions. EPR studies suggested that Fe³⁺ ions entered in the lattice as tetragonally distorted octahedral symmetry or rhombic sites at low concentration of Fe₂O₃, whereas at higher concentration of Fe₂O₃ (beyond 1 mol%), the super exchange type of interactions between multivalency iron ions begin to dominate. FTIR and Raman spectra have revealed the behaviour of various structural units in the glass ceramic matrix. The analysis of these spectroscopic studies indicates that iron ions do exist in Fe³⁺ and Fe²⁺ state.     

Evidence for electronic localization in YBa2−yLayCu3Ox

Electrical resistivity, thermoelectric power, magnetic susceptibility and neutron scattering experiments on YBa_2−yLa_yCu₃O_x, with y = 1, show that this compound is neither superconductive nor magnetically ordered but are consistent with it being an electronically localized system.     

Synthesis and characterization of (Bi2O3)1−x−y−z(Gd2O3)x (Sm2O3)y(Eu2O3)z quaternary solid solutions for solid oxide fuel cell

Sm₂O₃, Gd₂O₃, Eu₂O₃ triple-doped Bi₂O₃ based quaternary solid solutions were synthesized as a candidate electrolyte material using the solid-state reaction technique. The structural, thermal and electrical conductivity features of the ceramic samples were examined and compared by using X-ray powder diffraction (XRD), thermal gravimetry/differantial thermal analysis (TG/DTA) and the four-point probe technique (4PPT). The result of XRD measurements indicated that the (Bi₂O₃)_{(1−x−y−z)}(Gd₂O₃)_x(Sm₂O₃)_y(Eu₂O₃)_z (x = 10/y = 10/z = 5, 15, 20 mol % and x = 10/y = 5, 10, 15, 20/z = 10 mol %) samples have a stable face-centered cubic δ-phase and mixed phase crystallographic structure. The phase stability was also checked by the DTA evaluations results. The temperature dependent electrical conductivity measurements showed that the highest electrical conductivity was observed for the sample of the (Bi₂O₃)_0.75(Gd₂O₃)_0.10(Sm₂O₃)_0.05(Eu₂O₃)_0.10 system which has a stable and δ-phase was found as 6.67 × 10⁻³ (Ω cm)⁻¹ at 650 °C. This sample can be used as an electrolyte material in the solid oxide fuel cells (SOFCs) which is possible to operate at intermediate temperature ranges. The activation energy was also calculated at a low temperature range (350–650 °C) and high temperature range (above 650 °C). The values for the samples vary from 0.63 eV to 1.08 eV at low temperature and at high temperature they vary from 0.43 eV to 0.75 eV.     

Fluorination of superconducting Ba2YCu3O9−δ

Using a series of samples ranging in composition from δ = 2 to δ = 3 we have successfully introduced substantial amounts of fluorine into samples of superconducting Ba₂YCu₃O_9-δ by annealing under F₂ gas flows at low temperatures. These syntheses yielded single phase materials containing up to 1.05 F per formula unit. ¹⁹F NMR experiments have confirmed that fluorine is incorporated into the lattice and susceptibility and transport measurements indicate that the samples are superconducting with critical temperatures in the range 80 to 89 K.     

Study of the CO2-3 impurity in KTa1−xNbxO3

Infrared transmission and Raman scattering permitted the detection of CO^2-₃ impurities in KTaO₃ and KTa_1−xNb_xO₃ materials. These impurities could generate the observed anomalies in the physical properties of such compounds.