等浓度的氯化铵和硫酸铵溶液哪个pH高

有中学化学参考资料题:0.10 mol/L的NH4Cl和(NH4)2SO4溶液哪个pH值高?这似乎是个中学生可做的简单题目,仔细考虑不是如此.如果简单地认为盐酸和硫酸都是强酸,而硫酸是二元酸,硫酸铵溶液中铵盐浓度为0.20 mol/L,那么NH4Cl溶液pH高,那是不妥的.硫酸是二元酸,第一个氢离子能完全电离,第二个氢离子部分电离,如此考虑情况怎么样呢?是不是答案发生变化?这要通过计算来说明.     

Enhanced efficiency and stability in Sn-based perovskite solar cells with secondary crystallization growth

The conversion efficiencies reported for Tin(Sn)halide-based perovskite solar cells(PSCs)fall a large gap behind those of lead halide-based PSCs,mainly because of poor film quality of the former.Here we report an efficient strategy based on a simple secondary crystallization growth(SCG)technique to improve film quality for tin halide-based PSCs by applying a series of functional amine chlorides on the perovskite surface.They were discovered to enhance the film crystallinity and suppress the oxidation of Sn²⁺remarkably,hence reduce trap state density and non-irradiative recombination in the absorber films.Furthermore,the SCG film holds the band levels matching better with carrier transport layers and herein favoring charge extraction at the device interfaces.Consequently,a champion device efficiency of 8.07% was achieved alo ng with significant enhancements in VOC and JSC,in contrast to 5.35% of the control device value.Moreover,the SCG film-based devices also exhibit superior stability comparing with the control one.This work explicitly paves a novel and general strategy for developing high performance lead-free PSCs.     

Energy level engineering of charge selective contact and halide perovskite by modulating band offset:Mechanistic insights

Mixed cation and anion based perovskites solar cells exhibited enhanced stability under outdoor conditions,however,it yielded limited power conversion efficiency when TiO₂ and Spiro-OMeTAD were employed as electron and hole transport layer(ETL/HTL)respectively.The inevitable interfacial recombination of charge carriers at ETL/perovskite and perovskite/HTL interface diminished the efficiency in planar(n-i-p)perovskite solar cells.By employing computational approach for uni-dimensional device simulator,the effect of band offset on charge recombination at both interfaces was investigated.We noted that it acquired cliff structure when the conduction band minimum of the ETL was lower than that of the perovskite,and thus maximized interfacial recombination.However,if the conduction band minimum of ETL is higher than perovskite,a spike structure is formed,which improve the performance of solar cell.An optimum value of conduction band offset allows to reach performance of 25.21%,with an open circuit voltage(VOC)of 1231 mV,a current density JSC of 24.57 mA/cm² and a fill factor of 83.28%.Additionally,we found that beyond the optimum offset value,large spike structure could decrease the performance.With an optimized energy level of Spiro-OMeTAD and the thickness of mixed-perovskite layer performance of 26.56% can be attained.Our results demonstrate a detailed understanding about the energy level tuning between the charge selective layers and perovskite and how the improvement in PV performance can be achieved by adjusting the energy level offset.     

A new strategy to access Co/N co-doped carbon nanotubes as oxygen reduction reaction catalysts

Carbon nanotubes(CNTs),as one-dimensional nanomaterials,show great potential in energy conversion and storage due to their efficient electrical conductivity and mass transfer.However,the security risks,time-consuming and high cost of the preparation process hinder its further application.Here,we develop that a negative pressure rather than a following gas environment can promote the generation of cobalt and nitrogen co-doped CNTs(Co/N-CNTs) by using cobalt zeolitic imidazolate framework(ZIF-67) as a precursor,in which the negative pressure plays a key role in adjusting the size of cobalt nanoparticles and stimulating the rearragement of carbon atoms for forming CNTs.Importantly,the obtained Co/N-CNTs,with high content of pyridinic nitrogen and abundant graphitized structure,exhibit superior catalytic activity for oxygen reduction reaction(ORR) with half-wave potential(E_1/2) of 0.85 V and durability in terms of the minimum current loss(2%) after the 30,000 s test.Our development provides a new pathway for large-scale and cost-effective preparation of metal-doped CNTs for various applications.     

Recent Advances of Pure Organic Room Temperature Phosphorescence Materials for Bioimaging Applications

Bioimaging,as a powerful and helpful tool,which allows people to investigate deeply within living organisms,has contributed a lot for both clinical theranostics and scientific research.Pure organic room temperature phosphorescence(RTP)materials with the unique features of ultralong luminescence lifetime and large Stokes shift,can efficiently avoid biological autofluorescence and scattered light through a time-resolved imaging modality,and thus are attracting increasing attention.This review classifies pure organic RTP materials into three categories,including small molecule RTP materials,polymer RTP materials and supramolecular RTP materials,and summarizes the recent advances of pure organic RTP materials for bioimaging applications.     

Stabilizing High-voltage Cathode Materials for Next-generation Li-ion Batteries

The pressing demand for high-energy/power lithium-ion batteries requires the deployment of cathode materials with higher capacity and output voltage.Despite more than ten years of research,high-voltage cathode mate-rials,such as high-voltage layered oxides,spinel LiNi0.5Mn1.5O4,and high-voltage polyanionic compounds still cannot be commercially viable due to the instabilities of standard electrolytes,cathode materials,and cathode electrolyte interphases under high-voltage operation.This paper summarizes the recent advances in addressing the surface and interface issues haunting the application of high-voltage cathode materials.The understanding of the limitations and advantages of different modification protocols will direct the future endeavours on advancing high-energy/power lithium-ion batteries.     

Conformational Properties of Comb-shaped Polyelectrolytes with Negatively Charged Backbone and Neutral Side Chains Studied by a Generic Coarse-grained Bead-and-Spring Model

A generic coarse-grained bead-and-spring model,mapped onto comb-shaped polycarboxylate-based(PCE)superplasticizers,is developed and studied by Langevin molecular dynamics simulations with implicit solvent and explicit counterions.The agreement on the radius of gyration of the PCEs with experiments shows that our model can be useful in studying the equilibrium sizes of PCEs in solution.The effects of ionic strength,side-chain number,and side-chain length on the conformational behavior of PCEs in solution are explored.Single-chain equilibrium properties,including the radius of gyration,end-to-end distance and persistenee length of the polymer backbone,shape-asphericity parameter,and the mean span dimension,are determined.It is found that with the increase of ionic strength,the equilibrium sizes of the polymers decrease only slightly,and a linear dependenew of the persistence length of backbone on the Debye screening length is found,in good agreement with the theory developed by Dobrynin.Increasing side-chain numbers and/or side-chain lengths increases not only the equilibrium sizes(radius of gyration and mean span)of the polymer as a whole,but also the persistence length of the backbone due to excluded volume interactions.     

Suppressing trap states and energy loss by optimizing vertical phase distribution through ternary strategy in organic solar cells

Suppressing the trap-state density and the energy loss via ternary strategy was demonstrated.Favorable vertical phase distribution with donors(acceptors)accumulated(depleted)at the interface of active layer and charge extraction layer can be obtained by introducing appropriate amount of polymer acceptor N2200 into the systems of PBDB-T:IT-M and PBDB-TF:Y6.In addition,N2200 is gradiently distributed in the vertical direction in the ternary blend film.Various measurements were carried out to study the effects of N2200 on the binary systems.It was found that the optimized morphology especially in vertical direction can significantly decrease the trap state density of the binary blend films,which is beneficial for the charge transport and collection.All these features enable an obvious decrease in charge recombination in both PBDB-T:IT-M and PBDB-TF:Y6 based organic solar cells(OSCs),and power conversion efficiencies(PCEs)of 12.5%and 16.42%were obtained for the ternary OSCs,respectively.This work indicates that it is an effective method to suppress the trap state density and thus improve the device performance through ternary strategy.     

Three-dimensionalization via control of laser-structuring parameters for high energy and high power lithium-ion battery under various operating conditions

Laser-structuring is an effective method to promote ion diffusion and improve the performance of lithium-ion battery(LIB)electrodes.In this work,the effects of laser structuring parameters(groove pitch and depth)on the fundamental characteristics of LIB electrode,such as interfacial area,internal resistances,material loss and electrochemical performance,are investigated,LiNi_0.5Co_0.2Mn_0.3O₂ cathodes were structured by a femtosecond laser by varying groove depth and pitch,which resulted in a material loss of 5%-14%and an increase of 140%-260%in the in terfacial area between electrode surface and electrolyte.It is shown that the importance of groove depth and pitch on the electrochemical performance(specific capacity and areal discharge capacity)of laser-structured electrode varies with current rates.Groove pitch is more im porta nt at low current rate but groove depth is at high curre nt rate.From the mapping of lithium concentration within the electrodes of varying groove depth and pitch by laser-induced breakdown spectroscopy,it is verified that the groove functions as a diffusion path for lithium ions.The ionic,electronic,and charge transfer resistances measured with symmetric and half cells showed that these internal resistances are differently affected by laser structuring parameters and the changes in porosity,ionic diffusion and electronic pathways.It is demonstrated that the laser structuring parameters for maximum electrode performance and minimum capacity loss should be determined in consideration of the main operating conditions of LIBs.     

Mesh-like vertical structures enable both high areal capacity and excellent rate capability

In order to balance electrochemical kinetics with loading level for achieving efficient energy storage with high areal capacity and good rate capability simultaneously for wearable electronics,herein,2 D meshlike vertical structures(NiCo_2 S_4@Ni(OH)_2) with a high mass loading of 2.17 mg cm^-2 and combined merits of both 1 D nanowires and 2 D nanosheets are designed for fabricating flexible hybrid supercapacitors.Particularly,the seamlessly interconnected NiCo_2 S_4 core not only provides high capacity of 287.5 μAh cm^-2 but also functions as conductive skeleton for fast electron transport;Ni(OH)_2 sheath occupying the voids in NiCo_2 S_4 meshes contributes extra capacity of 248.4 μAh cm^-2;the holey features guarantee rapid ion diffusion along and across NiCO_2 S_4@Ni(OH)_2 meshes.The resultant flexible electrode exhibits a high areal capacity of 535.9 μAh cm^-2(246.9 mAh g^-1) at 3 mA cm^-2 and outstanding rate performance with 84.7% retention at 30 mA cm^-2,suggesting efficient utilization of both NiCo_2 S_4 and Ni(OH)_2 with specific capacities approaching to their theoretical values.The flexible solid-state hybrid device based on NiCo_2 S_4@Ni(OH)_2 cathode and Fe_2 O_3 anode delivers a high energy density of 315 μWh cm^-2 at the power density of 2.14 mW cm^-2 with excellent electrochemical cycling stability.     

CH2+O2反应的反应机理

The mechanisms of the CH2＋ O2→ H2O＋ CO and CH2＋ O2→ H2＋ CO2 reactions have been studied by performing ab initio CAS(8,8)/6-31G(d,p) calculations, and five intermediates(IMn) and eight transitions(TSn) have been located along the reaction paths. The predicted path for the CH2＋ O2→ H2O＋ CO is: CH2＋ O2→ TS1→ IM1→ TS2→ IM2→ TS3→ IM3→ TS4→ IM4a→ TS5→ H2O＋ CO. For the CH2＋ O2→ H2＋ CO2 reaction, there are two paths: (i) CH2＋ O2→ TS1→ IM1→ TS2→ IM2→ TS3→ IM3→ TS6→ H2＋ CO2 and (ii) CH2＋ O2→ TS1→ IM1→ TS2→ IM2→ TS3→ IM3→ TS4→ IM4a→ TS7→ IM4b→ TS8→ H2＋ CO2, with the latter path more favorable energetically.     

O(3P)+O2H——OH+O2反应机理的密度泛函理论研究

用密度泛函理论方法研究了O(³P)与O₂H反应生成羟基和氧分子的反应机理.在PW91/6-31+G^*水平上用梯度解析技术全自由度优化上述反应物、产物和反应路径上的中间体及过渡态几何构型,并通过频率振动分析加以确认,计算IRC反应路径及中间体异构化过程,确定了此反应的可能反应通道.结果表明:该反应是多通道多步骤的强放热反应.首先形成顺式或反式O₃H富能中间体,此过程无能垒;然后跨过一个能垒分解成产物OH和O₂.通道IM1→TS1比IM2→TS2克服的能垒要大,反应放热372.822kJ.mol^-1.IM1TS3IM2可相互转化.     

CH3CH2+O(3P)反应机理的理论研究

The reaction for CH3CH2+O(3P) was studied by ab initio method. The geometries of the reactants, intermediates, transition states and products were optimized at MP2/6-311+G(d,p) level. The corresponding vibration frequencies were calculated at the same level. The single-point calculations for all the stationary points were carried out at the QCISD(T)/6-311+G(d,p) level using the MP2/6-311+G(d,p) optimized geometries. The results of the theoretical study indicate that the major products are the CH2O＋CH3, CH3CHO+H and CH2CH2+OH in the reaction. For the products CH2O＋CH3 and CH3CHO+H, the major production channels are A1: (R)→IM1→TS3→(A) and B1: (R)→IM1→TS4→(B), respectively. The majority of the products CH2CH2+OH are formed via the direct abstraction channels C1 and C2: (R)→TS1(TS2)→(C). In addition, the results suggest that the barrier heights to form the CO reaction channels are very high, so the CO is not a major product in the reaction.     

SiH3+O(3P)反应机理的理论研究

The reaction for SiH3+O(3P) was studied by ab initio method. The geometries of the reactants, intermediates, transition states and products were optimized at MP2/6-311+G(d,p) level. The single point calculations for all the stationary points were carried out at the QCISD(T) /6-311+G(d,p) level using the MP2/6-311+G(d,p) optimized geometries. The results of the theoretical study indicate that the major pathway is the SiH3+O(3P)→IM1→TS3→IM2→TS8→HOSi+H2. The other minor products include the HSiOH+H, H2SiO+H and HSiO+H2. Furthermore, the products HOSi, HSiO and HSiOH(cis) can undergo dissociation into the product SiO. In addition, the calculations provide a possible interpretation for disagreement about the mechanism of the reaction SiH4+O(3P). It suggests that the products HSiOH, H2SiO and SiO observed by Withnall and Andrews are produced from the secondary reaction SiH3+O(3P) and not from the reaction SiH4+O(3P).     

Ab initio Study of the Potential Energy Surface and Product Branching Ratios for Reaction of O（^1D） with C2H5CI

The potential energy surface of O（^1D）＋C2H5Cl reaction was studied using QCISD（T）/6- 311＋＋G（d,p）//MP2/6-31G（d,p） method. The calculations reveal an insertion-elimination mechanism. The insertion reaction of O（^1D） and C2H5Cl produces two energy-rich intermediates, IM1 and IM2, which subsequently decompose into various products. The calculations of the branching ratios of various products formed through the two intermediates were carried out using RRKM （Rice-Ramsperger-Kassel-Marcus） theory at the collision energies of 0, 20.9, 41.8, 62.7, 83.6, 104.5, and 125.4 kJ/mol. HCl is the main decomposition product for IM1; CH2OH is the main decomposition product for IM2. Since IM1 is more stable than IM2, HCl is probably the main product of the O（^1D）＋C2H5Cl reaction.     

CH3SS与OH自由基反应机理的理论研究

应用密度泛函理论(DFT)对CH3SS与OH自由基单重态反应机理进行了研究.在B3PW91/6-311+G(d,p)水平上优化了反应通道上各驻点(反应物、中间体、过渡态和产物)的几何构型,用内禀反应坐标(IRC)计算和频率分析方法对过渡态进行了验证.在QCISD(T)/6-311++G(d,p)水平上计算了各物种的单点能,并对总能量进行了零点能校正.研究结果表明,CH3SS与OH反应为多通道反应,有5条可能的反应通道.反应物首先通过不同的S—O键相互作用形成具有竞争反应机理的中间体IM1和IM2.再经过氢迁移、脱氢和裂解等机理得到主要产物P1(CH2SS+H2O),次要产物P2(CH2S+HSOH),P3(CH3SH+1SO)和P4(CH2SSO+H2),其中最低反应通道的势垒为174.6kJ.mol-1.     

三氟化氯和环氧丙烷反应的理论研究

应用密度泛函理论对三氟化氯和环氧丙烷反应产生C3H5O和C1F2自由基的机理进行了研究。在B3PW91/6-31+G(d,p)水平优化了12个不同反应通道上各驻点(反应物、中间体、过渡态和产物) 的几何构型,并计算了它们的振动频率和零点振动能。采用CCSD(T)/6-31+ G(d,p) // B3PW91/6-31+G(d,p)单点能计算方法求得各物种的能量,并作了零点能校正。计算结果表明,三氟化氯和环氧丙烷反应可经过不同的反应路径引发C3H5O自由基和C1F2自由基,其中,三氟化氯呈对称的F原子与环氧丙烷的C(1)上与CH3在同一侧的上的H原子结合的活化能最低,仅为16.81 kJ/mol。     

CH3S与HO2气相反应机理的理论研究

采用密度泛函理论的B3LYP方法, 在6-311＋＋G(d,p)基组水平上研究了CH3S自由基与HO2自由基的微观反应机理, 全参数优化了反应势能面上各驻点的几何构型, 振动分析和内禀反应坐标(IRC)分析结果证实了中间体和过渡态的真实性, 计算所得的键鞍点电荷密度的变化情况也确认了反应过程. 找到了五条可能的反应通道, 对结果的分析表明: 单线态反应通道(5) CH3S＋HO2→CH3SOOH (1P), 是所有通道中的主要反应通道. 该通道不需要克服过渡态能垒, 属于放热反应, 在动力学和热力学上都是最为有利的. 对于三线态反应通道来说, 通道(1)CH3S＋HO2→COM11→TS1→COM12→CH3SH＋O2 (3P)为主要反应通道, 控制步骤的活化能为53.5 kJ/mol, 能垒最低, 属于放热反应, 在动力学和热力学上都是有利的.     

CF3O2自由基和NO反应机理的理论研究

用密度泛函理论(DFT)的B3LYP方法, 分别在6-31G、6-311G、6-311+G(d)基组水平上研究了CF3O2自由基和NO反应机理. 研究结果表明, CF3O2自由基和NO反应存在三条可行的反应通道, 优化得到了相应的中间体和过渡态. 从活化能看, 通道CH3O2+NO→IM1→TS1→IM2→TS2→CF3O+ONO的活化能最低, 仅为70.86 kJ•mol-1, 是主要反应通道, 主要产物是CF3O和NO2. 而通道CH3O2+NO→IM1→TS3→CF3ONO2和CH3O2+NO→TS4→IM3→TS5→IM4→TS6→CF3O+NOO的活化能较高, 故该反应难以进行.     

Mechanism for the gas‐phase reaction between OH and 3‐methylfuran: A theoretical study

The mechanism for the OH + 3‐methylfuran reaction has been studied via ab initio calculations to investigate various reaction pathways on the doublet potential energy surface. Optimizations of the reactants, products, intermediates, and transition structures are conducted using the MP2 level of theory with the 6‐311G(d,p) basis set. The single‐point electronic energy of each optimized geometry is refined with G3MP2 and G3MP2B3 calculations. The theoretical study suggests that the OH + 3‐methylfuran reaction is dominated by the formation of HC(O)CH?C(CH₃)CHOH (P7) and CH(OH)CH?C(CH₃)C(O)H (P9), formed from two low‐lying adducts, IM1 and IM2. The direct hydrogen abstraction pathways and the S_N2 reaction may play a minor or negligible role in the overall reaction of OH with 3‐methylfuran. © 2008 Wiley Periodicals, Inc. Int J Quantum Chem, 2008