Structure and optical properties of sol–gel derived Gd2O3 waveguide films

Pure and rare earth doped gadolinium oxide (Gd₂O₃) waveguide films were prepared by a simple sol–gel process and dip-coating method. Gd₂O₃ was successfully synthesized by hydrolysis of gadolinium acetate. Thermogravimetric analysis (TGA) and differential thermal analysis (DTA) were used to study the thermal chemistry properties of dried gel. Structure of Gd₂O₃ films annealed at different temperature ranging from 400 to 750 °C were investigated by Fourier transform infrared (FT-IR) spectroscopy, X-ray diffraction (XRD) and transmission electron microscopy (TEM). The results show that Gd₂O₃ starts crystallizing at about 400 °C and the crystallite size increases with annealing temperature. Oriented growth of (4 0 0) face of Gd₂O₃ has been observed when the films were deposited on (1 0 0) Si substrate and annealed at 750 °C. The laser beam (λ=632.8 nm) was coupled into the film by a prism coupler and propagation loss of the film measured by scattering-detection method is about 2 dB/cm. Luminescence properties of europium ions doped films were measured and are discussed.     

Preparation of LiMn2O4 thin films by a sol–gel method

LiMn₂O₄ thin films were prepared by a sol–gel method using spin-coating and annealing processes. Anhydrous Mn(CH₃COCHCOCH₃)₃ (manganese acetylacetonate) and LiCH₃COCHCO–CH₃ (lithium acetylacetonate) were chosen as source materials. The film electrochemical properties depended on the drying temperature even when subjected to the same annealing conditions. The discharge capacity of annealed film increased as the drying temperature was increased. However, the rate of capacity fading during cycling increased as the drying temperature was increased.     

Sol–gel preparation and characterisation of dense proton conducting Sr3CaZr0.5Ta1.5O8.75 thin films

Dense proton conducting Sr₃CaZr_0.5Ta_1.5O_8.75 films (1.25 μm, with grain size in the 200–400 nm range) were deposited, using the sol–gel method, on Al₂O₃–8%Y₂O₃-stabilised ZrO₂ plates. The obtained gels were characterised by differential and thermogravimetric thermal analysis (DTA–TGA), X-ray diffraction (XRD) and scanning electron microscopy (SEM). The results of a study of the structural and electrical properties of Sr₃CaZr_0.5Ta_1.5O_8.75 films deposited on the mentioned substrates are presented herein. The structural data for the gels and films were compared with those obtained for the same material prepared by solid state synthesis. Electrical properties of the sandwich-type structure were investigated by AC impedance conductivity measurements at different temperatures, in both dry and wet 5% H₂/Ar atmospheres. A careful analysis of the impedance spectra for this complex structure was performed, using a model with a series of five electrical circuits, having resistance and capacitance coupled in parallel. The specific responses observed in the impedance spectra were assigned to the corresponding substrate and layer contributions. A significant improvement, by an order of magnitude, in the electrode response was observed in the presence of the interleaving Sr₃CaZr_0.5Ta_1.5O_8.75 proton conducting layer, between the electrode and electrolyte. This enhancement is lost at temperatures above that at which the Sr₃CaZr_0.5Ta_1.5O_8.75 dehydrates and its protonic conductivity diminishes. Considering the structural and electrical characterisation results, these Sr₃CaZr_0.5Ta_1.5O_8.75 sol–gel derived films have a potential use for proton conducting electrolyte or intermediate layer in fuel cells.     

Luminescence from porous silicon doped with erbium–ytterbium complexes

The study of photoluminescence (PL) from porous silicon (PS) containing complexes of gadolinium oxychloride with Er³⁺- and Er³⁺–Yb³⁺ is reported. The concentration dependencies of PL intensity of PS with Er³⁺ containing complex have been studied. The dependencies have retained the main features that are characteristic of the pure complex for both IR and visible regions of the PL spectra. This allows interpretation of PL processes in complex-containing PS lthrough the concept of multiplication of low-energy electron excitations and cross-relaxation degradation of higher excited states. It has been shown that introducing Yb³⁺ ions into the complex significantly increases the PL intensity. Mechanisms associated with defect formation, the intrinsic conversion of excitation energy within Yb³⁺, and the conversion within Er³⁺ ions followed by transferring of excitation energy to the Yb³⁺ ions has been considered. The PL polarization with excitation in the visible is reported as well.     

Optical properties of γ-Fe2O3 nanoparticles dispersed on sol–gel silica spheres

Two types of γ-Fe₂O₃ nanoparticles, pure γ-Fe₂O₃ and γ-Fe₂O₃ dispersed on sol–gel silica spheres (γ-Fe₂O₃/SiO₂) in thin film form were prepared by the sol–gel technique. Transmission electron microscopy, X-ray diffraction, optical transmittance and FTIR studies along with photoluminescence measurements were carried out for characterizing the samples. The X-ray diffraction patterns of both γ-Fe₂O₃ nanoparticles and γ-Fe₂O₃/SiO₂ indicated their phase-pure forms which were supported by the FTIR spectra. The average sizes of the nanoparticles obtained from transmission electron microscopy studies were 4 nm for both types of samples. Optical transmittance studies indicated direct allowed transitions with two band gaps at 2.43 and 3.07 eV. Although both types of samples showed excitonic luminescence at 2.38 eV (at room temperature), the luminescence intensity of the γ-Fe₂O₃/SiO₂ was higher than that of pure γ-Fe₂O₃.     

Up-conversion luminescence saturation under pulsed excitation of erbium-doped, SiO2–TiO2 sol–gel powders

The intensity of erbium up-conversion luminescence could be limited by a saturation effect due to increased pump power. We studied the luminescence saturation of the 550 nm emission on erbium-doped, SiO₂–TiO₂ sol–gel powders under pulsed excitation at 979 and 1532 nm. From the latter, the up-converted luminescence intensity decreased with increasing excitation power, whereas no saturation was observed at 979 nm excitation. We proposed that the saturation effect is determined by the pump power, the erbium content and the lifetime of the corresponding first excited states at different pumping schemes.     

Synthesis and characterization of monodispersed CdS nanoparticles in SiO2 fibers by sol–gel method

Cadmium sulfide (CdS) has been synthesized by a sol–gel route in order to obtain chemically protected, stable nanoparticles. The CdS nanoparticles in the SiO₂ gel matrix were dried to form monoliths of 1 in. diameter. The TEOS:H₂O:HCl:C₂H₅OH and TEOS/Cd mole ratios were varied to obtain narrow size distributed CdS nanoparticles. The UV absorption measurements indicated sharp absorption at 260 and 350 nm for different precursor compositions. SiO₂ gel containing the CdS nanoparticles was spin coated onto substrates in order to monitor the surface morphology of the samples. Scanning electron microscope measurements revealed formation of CdS nanoparticles within the branches of gel-network. Depending upon the mole ratio of additives and drying method, fibers or monolithic tablets of CdS nanoparticles could be produced.     

Studies of sol–gel TiO2 and Pt/TiO2 catalysts for NO reduction by CO in an oxygen-rich condition

The textural properties, morphological features, surface basicity and oxygen reduction behaviours of titania and Pt supported titania catalysts synthesized via a sol–gel method were studied by means of N₂ physisorption, SEM, TEM, CO₂-TPD and H₂-TPR techniques. Mesostructured TiO₂ shows a very narrow pore size distribution that uniformly centred at about 4 nm. High resolution TEM images confirmed that most of Pt particles on Pt/TiO₂-SG had a size smaller than 2 nm. Both the titania support and Pt loaded catalysts chiefly contained weak basic sites with small amount of strong basic sites. Loading Pt did not significantly alter the surface reduction characters of titania, indicating a weak interaction between Pt metals and titania support. Catalytic evaluation revealed that the selectivity of NO reduction over titania was insensitive to variation of textural property. On the bare titania, low NO conversion but high selectivity to N₂O was obtained. However, the Pt/TiO₂-SG catalysts exhibited high NO conversion and high selectivity to N₂, which is assumed to relate to NO dissociation catalysed by the metallic Pt clusters. In addition, when the reaction temperature was above 200 °C, 3–11% NO₂ was yielded over the Pt/TiO₂-SG catalysts, which was discussed on a basis of reaction competition, metal-support interaction and NO dissociation.     

Effects of substitution of Ti for Fe in BiFeO3 films prepared by sol–gel process

Ti substituted BiFe_1−xTi_xO_3+δ films have been prepared on indium–tin oxide (ITO)/glass substrates by the sol–gel process. The films with x=0.00–0.20 were prepared at an annealing temperature of 600 °C. X-ray diffraction patterns indicate that all films adopt R3m structure and the films with x=0 and 0.10 show pure perovskite phase. Cross-section scanning shows the thickness of the films is about 300 nm. Through 0.05 Ti substitution, the 2P_r increases to 8.30 μC/cm² from 2.12 μC/cm² of the un-substituted BiFeO₃ film and show enhanced ferroelectricity at room temperature. The 2P_r values are 2.63 and 0.44 μC/cm² for the films with x=0.01 and 0.2, respectively. Moreover, the films with x=0.05 and 0.10 show enhanced dielectric property since the permittivity increases near 150 at the same measuring frequency. Through the substitution of Ti, the leakage conduction is reduced for the films with x=0.05–0.20.     

Electrical and optical characteristics of porous silicon impregnated with LaF3 by a novel chemical bath technique

The structural, electrical and optical characteristics of porous silicon (PS) due to the impregnation of LaF₃ into PS by a novel chemical-bath deposition (CBD) technique have been investigated in this article. Without removing the PS from the anodization chamber the impregnation with LaF₃ has been done by reacting LaCl₃ with HF in the same chamber at room temperature. The impregnation of LaF₃ was confirmed by the SEM on the cross-section of the LaF₃/PS/Si system and EDX. The modification of PS surface by LaF₃ had direct influence on the electrical and optical properties of PS. Electrical properties of Ag/LaF₃/PS/p-Si/Ag structures were studied through the current-voltage (I-V) and capacitance-voltage (C-V) characteristics. Formation of metal-insulator-semiconductor (MIS) diode was evident whose forward current increased with annealing. A diode factor of about 2.4 has been obtained for the annealed heterostructure indicating a high density of trap states. The C⁻²-V curves of all samples showed negative flat band voltage of around −2 V confirming a large number of fixed positive charges in the LaF₃. The photoluminescence (PL) intensity of the LaF₃-impregnated PS showed aging for the as-deposited samples, but when annealed PS structure recovered the PL intensity. Experimental results show that the optimized chemical bath passivation process for the LaF₃ on porous silicon could enable the porous silicon to be an important material for photonic application.     

Luminescence of rare earth-doped Si–ZrO2 co-sputtered films

Er-doped Si-yttria-stabilized zirconia (YSZ) thin film samples were prepared by rf co-sputtering. Chemical composition of the samples was determined using energy-dispersive spectroscopy (EDS) and the structure of the films by X-ray diffraction (XRD). The samples were annealed to 700 °C. Photoluminescence (PL) measurements were performed for the visible and infrared. By exciting with the 488-nm-laser line the Er³⁺ emissions ²H_11/2→⁴I_15/2, ⁴S_3/2→⁴I_15/2, ⁴F_9/2→⁴I_15/2 and a narrow ⁴I_13/2→⁴I_15/2 emission were observed. The ⁴I_11/2→⁴I_15/2 emissions for the same excitation wavelength were weak. Excitation wavelength dependence of the ⁴I_13/2→⁴I_15/2 emissions indicated that the emissions were due to a combination of energy transfer from Si nanoparticles (np) to Er ions and energy transfer from defects in the matrix to the Er ions for excitations resonant with the energy levels of such defects. ⁴I_13/2→⁴I_15/2 emission decay measurements show two decaying populations of Er ions according to their locations with respect to other ions or any non-radiative defects. ⁴I_11/2→⁴I_15/2 emission dependence on ⁴I_13/2→⁴I_15/2 emission showed that the former was possibly due to a combination of downconversion from higher levels of the Er ions, energy transfer from Si nanoparticles and upconversion transfer processes. We concluded that Er-doped Si-YSZ is a promising material for photonic applications being easily broadband excited using low-pumping powers.     

Luminescence and circularly polarized luminescence of macrocyclic Eu(III) and Tb(III) complexes embedded in xerogel and sol–gel SiO2 glasses

Luminescence, time-resolved luminescence, circularly polarized luminescence (CPL) and decay profiles of Ln(III)(15-crownether-5) (Ln=Ce, Sm, Eu, Tb) and Tb(III)-(R),(S)-cyclen derivative complexes doped in xerogel and sol–gel silica glasses are measured at temperatures down to 10 K to characterize luminescence properties and the electronic structure in the excited states. Luminescence spectral profiles and calculation of crystal field parameters (B₀⁽²⁾,B₂⁽²⁾) in the ⁵D₀→⁷F_J(J=1,2) transition give evidence of the fact that the pentagonal and planar structure of Eu(III) (15-crownether-5) does hold in xerogel and sol–gel glasses prepared at temperatures below 100°C. As annealing temperatures are increased from 80°C to 750°C, Eu(III) complexes in sol–gel glasses are found to decompose gradually to SiO₂:Eu³⁺. Tb(III)-(R) and (S)-cyclen derivative complexes in xerogel reveal at room temperature and 10 K sharp CPL spectra with luminescence dissymmetry factors g_lum=−0.1 and 0.1, respectively. These complexes doped in sol–gel glasses represent luminescence characteristics of rare earth ions encapsulated in the nano-porous host.     

Raman spectroscopy of sol–gel derived titanium oxide thin films

Raman spectra of TiO₂ films prepared via the sol–gel process were studied by UV and visible Raman spectroscopy. The evolution of the phases of TiO₂ films during annealing was investigated, and the relative intensities of the Raman bands excited with 325 nm were found to be distinct from those of the bands excited with 514 nm. The transmittance and FTIR spectra of the films annealed at different temperatures were characterized. The crystallization process of the powders and thin films treated by different annealing methods were also studied with Raman spectroscopy. The results show that the change in the relative intensities is caused by the resonance Raman effect. The anatase to rutile transition of the powder occurs at 700 °C, while that of the thin film occurs at 800 °C. The analysis of Raman band shape (peak position and full width at half‐maximum) after conventional furnace annealing and rapid thermal annealing indicates the influence of the non‐stoichiometry and phonon confinement effect. Copyright © 2011 John Wiley & Sons, Ltd.     

Synthesis of self-assembly BaTiO3 nanowire by sol–gel and microwave method

Self-assembly ferroelectric BaTiO₃ nanowires were fabricated using sol–gel and microwave method. The X-ray diffraction patterns show that BaTiO₃ nanowires belong to the tetragonal perovskite structure. An increase in the intensity of (1 1 0) peak was observed as the annealing time increased. The shape of BaTiO₃ nanowires microwave-annealed for different minutes was investigated using atomic force microscopy. It is found that nanowires of BaTiO₃ annealed for 2.5 min are very clear-cut, orderly and almost uninterrupted. The height of nanowire is near to the film thickness. However, nanowires of BaTiO₃ annealed for 5 min are lesser, shorter and lower, and the distances among these nanowires are wider and well-proportioned. The origin of the distinct differences due to the remotion of atoms obtained enough energy was discussed.     

Structural characterization of the sol–gel oxide powders from the ZnO–TiO2–SiO2 system

This work is a study that deals with the synthesis by the sol–gel method and the structural characterization of the oxide powders belonging to the ternary system ZnO–TiO₂–SiO₂ (ZTS). The sol–gel synthesis starts from inorganic precursors, which have been processed under the variation of different technological parameters. We have investigated the dependence of the gelling time on pH and on the temperature of synthesis as well as on water and ammonia amounts. In the case of ZTS samples, the shortest gelling duration appears for low pH values when ZnO content is increased and at small ammonia concentrations when the ZnO content is decreased, respectively. On the contrary, ZTS samples containing high amounts of TiO₂ provide evidence of a short gelling time for high pH and large ammonia amounts. X-ray diffraction (XRD) and Fourier transform infrared (FTIR) spectroscopy provided structural information on these ternary oxide powders. These analyses revealed that relative high amounts of ZnO yields in a change from octahedral [ ZnO₆] units to tetrahedral [ ZnO₄] units in the powder structure. Optical phonons specific for SiO₂ and TiO₂ in both octahedral and tetrahedral groups are shown. High thermal and chemical stability was put in evidence by differential thermal analysis (DTA) and thermo-gravimetric analysis (TGA) in the 20–1000 C temperature range.     

1.54 μm Emission of pulsed-laser deposited Er-doped films on Si

We investigate the photoluminescence properties of Er-doped SiO₂ and glass films fabricated by pulsed-laser deposition (PLD) for different deposition parameters and erbium host materials. The luminescence yield of SiO₂ : Er films increases strongly with increasing oxygen background pressure during laser ablation. We compare SiO₂ and soda-lime glass as host materials for erbium ions. Under identical growth conditions and the same erbium concentrations in both targets, films deposited from the soda-lime glass show a much higher luminescence yield. This enhancement is attributed to a higher concentration of optically active erbium in the multicomponent glass environment.     

Effect of C doping on the structural and optical properties of sol–gel TiO2 thin films

Undoped and C-doped TiO₂ thin films have been prepared by sol–gel process. Their structure and optical properties have been investigated by X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), and UV–vis spectroscopy. It has been observed that C dopants retard the transformation from anatase-to-rutile phase. Namely, C doping effect is attributed to the anatase phase stabilization. The optical analyses show that the optical band gap of anatase C-doped TiO₂ decreases with increasing amount of C. Also, it is founded that C dopants have been shown to make TiO₂ have a visible light photoresponse.     

Effect of pore size on ferroelectric properties of multiferroic BiFeO3 films prepared on porous silicon

The ferroelectric properties of BiFeO₃ (BFO) films spray deposited on porous silicon have been studied. The analysis of XRD and FESEM investigations show that the crystalline strain in the BFO films increases with pore size. The BFO films on porous silicon substrate showed improvement in ferroelectric fatigue behavior, remanent polarization and ferroelectric switching time. A maximum memory window of 5.54 V at 1 MHz and a large remanent polarization (P_r) of 13.1 μC/cm² have been obtained at room temperature. The improvement in the ferroelectric properties of these films has been correlated to the crystalline strain.     

Crystallization behavior and origin of c-axis orientation in sol–gel-derived ZnO:Li thin films on glass substrates

Preferentially, c-axis-oriented lithium-doped zinc oxide (ZnO:Li) thin films were prepared on Pyrex borosilicate glass substrates by a sol–gel method starting from zinc acetate dihydrate, lithium chloride, 2-methoxyethanol and monoethanolamine. Decomposition and crystallization behavior of dip-coated amorphous precursor films during post-annealing treatments were investigated by thermogravimetry–differential thermal analysis (TG–DTA), X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), optical transmittance measurements, field emission scanning electron microscopy (FESEM) and atomic force microscopy (AFM). It was revealed that the films contained the organic compounds at temperatures up to 300°C, which was the key to the transformation from the amorphous to the crystalline state. Thermodynamical consideration of nucleation and crystal growth was made taking account of surface energies of the film and the glass substrate and an interfacial energy between them. Mechanisms underlying the c-axis orientation were proposed based upon the initial orientation due to nucleation and final growth orientation.     

Fabrication of three-dimensionally ordered macroporous Ta2O5 films through aqueous organic gel process

Ta₂O₅ thin films have been prepared in the forms of three-dimensionally ordered macroporous (3-DOM) materials through aqueous organic gel process guided by polystyrene (PS) colloidal templates. The structure of the films was strongly affected by the infiltration process. This suggests that the infiltration process which aims at introducing desired materials into the interstitial spaces between the PS templates is of critical importance. Dip-drawing method was adopted for infiltration in this article. However, excess precursor worked as a capping agent for films prepared from the precursor of high concentration. Spin-coating method can efficiently remove the excess precursor by high speed rotating, which makes it a promising process for the infiltration of Ta-citric precursor with concentration higher than 0.5 mol/L. X-ray diffraction (XRD) pattern showed that the products can crystallize at 600 °C and had a pure orthorhombic phase. The chemical composition of the product was also studied by X-ray photoelectron spectroscopy (XPS).