Effect of vinyl acetate content and electron beam irradiation on the flame retardancy, mechanical and thermal properties of intumescent flame retardant ethylene-vinyl acetate copolymer

Ethylene vinyl acetate copolymer (EVA) flame retarded by ammonium polyphosphate (APP) and pentaerythritol (PER) was cross-linked by electron beam irradiation. The effects of vinyl acetate content and electron beam irradiation on the flame retardancy, mechanical and thermal properties of EVA composites were investigated. The volatilized products of EVA/APP/PER composites were characterized by thermogravimetric analysis/infrared spectrometry. As VA content increased, the volatilized products increased in the second decomposition step, but decreased in the third decomposition step. For all samples, the increase of irradiation dose could improve both the gel content and the Limit Oxygen Index (LOI, the minimum oxygen concentration by volume for maintaining the burning of a material) values of irradiated composites. The mechanical and thermal properties of the irradiated EVA composites were also evidently improved at appropriate irradiation dose as compared with those of unirradiated EVA composites, whereas these properties decrease at higher irradiation dose because of the electron beam irradiation-induced oxidative degradation or chain scission.     

Synergistic effects and mechanism of multiwalled carbon nanotubes with magnesium hydroxide in halogen-free flame retardant EVA/MH/MWNT nanocomposites

The synergistic effects and mechanism of multiwalled carbon nanotubes (MWNTs) with magnesium hydroxide (MH) in halogen-free flame retardant EVA/MH/MWNT nanocomposites have been studied by cone calorimeter test (CCT), limiting oxygen index (LOI), thermogravimetric analysis (TGA), torque test, morphological evolution experiment, and scanning electron microscopy (SEM). The data obtained from the CCT, LOI, and TGA show that suitable amount of MWNTs has synergistic effects with MH in the EVA/MH/MWNT nanocomposites. The MWNTs can considerably decrease the heat release rates and mass loss rate by about 50-60%, prolongate the combustion time to near two times, and increase the LOI values by 5% when 2 wt% MWNTs substitute for the MH in the EVA/MH/MWNT samples. The TGA data also show that the synergistic effects of MWNTs with MH apparently increase the thermal degradation temperatures and final charred residues of the EVA/MH/MWNT samples. The experimental observations from the torque, morphological evolution tests, and SEM give positive evidences that the synergistic mechanism of MWNTs with MH can be described to: (i) the increase of melt viscosity because of network structure formation of MWNTs in the EVA/MH matrix; (ii) the enhancement of thermo-oxidation stability due to the MWNTs' mechanical strength and integrity of the charred layers in the EVA/MH/MWNT nanocomposites; (iii) the formation of compact charred layers promoted by MWNTs acted as heat barrier and thermal insulation. All the above-mentioned factors efficiently enhance thermal and flame retardant properties and protect the EVA/MH/MWNT nanocomposite materials to be burning.     

Preparation and characterization of flame retardant and low smoke releasing oil-resistant EVA/NBR blends

Nano-Si O2 and/or Mo O3 were introduced to ethylene-vinyl acetate/nitrile butadiene rubber(EVA/NBR) blends containing magnesium hydroxide(MH) and red phosphorus(RP) to further improve the mechanical properties, oil resistance, smoke suppression and flame retardancy. The results indicated that the tensile strength and oil resistance were significantly improved by incorporating nano-Si O2. Smoke suppression tests for EVA/NBR blend samples showed that both nano-Si O2 and Mo O3 can significantly reduce smoke release amount. The flammability characterization indicated that the blended sample with an LOI value of 33.0 could achieve V-0 level in the UL-94 test. Cone calorimetry test data showed the peak heat release rate was 67% lower than that for pure EVA/NBR. Thermal analysis showed that the presence of both nano-Si O2 and Mo O3 was beneficial to promoting char formation of the EVA/NBR blends. Char residual analysis suggested that Mo O3 aggregated in solid phase during combustion.     

GaP/GaPN核壳纳米线阵列修饰的硅光阴极的光电化学制氢反应（英文）

能够大规模同时提升电极的催化效率和稳定性对光电化学分解水系统的开发具有重要意义.硅是一种地球储量丰富且成熟的工业材料,由于其合适的带隙(1.1 eV)和优异的导电性,已被广泛用于光电化学制氢反应.然而,缓慢的表面催化反应和在电解液中的不稳定性限制了其在太阳能制氢中的实际应用.III-IV族半导体材料也具有较高的载流子传输特性且被广泛用于光电器件.其中,GaP的直接带隙和间接带隙分别为2.78和2.26 eV,可与硅组成串联型光电极用于光电化学分解水.然而,GaP的光腐蚀电位位于禁带中,很容易在光电催化过程中发生光腐蚀而导致性能大幅下降.本文报道了一种新型的GaP/GaPN核/壳纳米线修饰的p型硅(p-Si)串联型光阴极,同未修饰的p-Si相比,其光电化学制氢性能更高.这可归因于以下几点:(1)p-Si和GaP纳米线之间形成的p-n结促进了电荷分离;(2)GaPN相对于GaP具有更低的导带边位置,进一步促进了光生电子向电极表面的转移;(3)纳米线结构既缩短了光生载流子的收集距离,又增加了比表面积,从而加快了表面反应动力学.此外,在GaP中引入氮元素还提高了体系的光吸收和稳定性.我们所提出的高效、简便的改进策略可应用于其他的太阳能转换体系.利用简单的化学气相沉积法制备GaP/GaPN核/壳纳米线修饰的p-Si光阴极.首先在p-Si衬底上利用Au纳米颗粒作为催化剂生长GaP纳米线;然后,去除Au催化剂,并在氨气中退火便形成了GaP/GaPN核壳纳米线.高分辨透射电子显微镜,拉曼光谱和X射线光电子谱的表征结果均证实了氨气退火使得GaP纳米线表面形成了GaPN的薄壳层,同时证明了GaP/GaPN核壳纳米线具有可调的核壳结构.在模拟太阳光下作为光阴极用于光解水制氢反应时,GaP/GaPN核壳纳米线修饰的p-Si光阴极的起始电位为~0.14 V,而未修饰的p-Si电极的起始电位大约在?0.77 V.而且,GaP/GaPN核/壳纳米线修饰的p-Si光阴极比未修饰的p-Si光阴极具有更高的光电流密度,在水的还原电位下,其光电流密度为?0.3 mA cm^-2,且饱和光电流密度在?0.76 V时达到了?8.8 mA cm^-2.此外,GaP/GaPN核/壳纳米线修饰的p-Si光阴极的光电化学活性在10 h内没有发生明显下降.由此可见GaP/GaPN核/壳纳米线可以规模化有效地提升Si光电极的催化效率和稳定性.     

Synergistic effect of zeolite 4A on thermal,mechanical and flame retardant properties of intumescent flame retardant HDPE composites

The combination of synergistic agent with intumescent flame retardant (IFR) systems provides a promising way to prepare high performance IFR composites. In this study, the effects of the synthetic zeolite 4 A in combination with the IFR system consisting of ammonium polyphosphate (APP) and tris (2-hydroxyethyl) isocynurate (THEIC) on thermal degradation, mechanical properties, flame retardancy and char formation of high-density polyethylene composites were investigated by limiting oxygen index (LOI) measurement, cone calorimetry, scanning electron microscopy and laser Raman spectroscopy. The LOI value of HD/FR/Z-0.5 composite with an optimum content of 0.5 wt. % zeolite 4 A and 25 wt. % of total flame retardant reaches 26.3 %. A low loading of zeolite 4 A can improve the bench-scale combustion performance as determined by cone calorimetry, and promote the formation of more compact char residue with a highly graphitic structure. However, a low loading of zeolite in combination with the IFR system consisting of APP and THEIC produces no significant changes in mechanical performance.     

Preparation and characterization of micron-sized polystyrene/polysiloxane core/shell particles

A procedure has been developed to coat micron-sized polystyrene (PS) spheres with a smooth layer of polysiloxane by a sol–gel process of methyl trimethoxylsilane (MTMS) without using silane coupling agents. The thickness of the shells can be easily varied with different polystyrene seeds and methyl trimethoxysilane feed ratio. When we used PS particles with diameters of 2.09 μm prepared by conventional dispersion polymerization as seeds, the thickness of the polysiloxane shells can be varied from 0.11 to 0.21 μm. The particle size, size distribution, thermal decomposition, and solvent resistance were investigated by scanning electron microscope (SEM), transmission electron microscope (TEM), size analyzer, and TG, respectively.     

Size-controlled synthesis of monodisperse core/shell nanogels

Small, monodisperse nanogels (∼50-nm radius) were synthesized by free-radical precipitation polymerization and were characterized using a suite of light scattering and chromatography methods. Nanogels were synthesized with either N-isopropylacrylamide or N-isopropylmethacrylamide as the main monomer, with acrylic acid or 4-acrylamidofluorescein as a comonomer and N,N′-methylenebis(acrylamide) as a cross-linker. By varying the surfactant and initiator concentrations, particle size was controlled while maintaining excellent monodispersity. An amine-containing shell was added to these core particles to facilitate subsequent bioconjugation. Successful conjugation of folic acid to the particles was demonstrated as an example of how such materials might be employed in a targeted drug delivery system.     

Preparation of gel‐silica/ammonium polyphosphate core‐shell flame retardant and properties of polyurethane composites

A novel intumescent gel‐silica/ammonium polyphosphate core‐shell flame retardant (MCAPP), which contains silicon, phosphorus, and nitrogen, has been prepared by in situ polymerization. The structure of MCAPP was characterized by Fourier transform infrared (FTIR) and X‐ray photoelectron spectroscopy (XPS). The properties of MCAPP were investigated by water solubility, hydrophilicity, and morphological determination. The flame retardancy and thermal stability of polyurethane (PU) composite with MCAPP were evaluated by limiting oxygen index (LOI), UL‐94 test, cone calorimetry, and thermogravimetric analysis (TGA). The results showed that MCAPP could decrease the heat release rate (HRR) and increase the thermal stability of PU materials greatly. Finally, water‐resistant properties of PU/FR composites were also studied. Copyright © 2010 John Wiley & Sons, Ltd.     

Precisely installing gold nanoparticles at the core/shell interface of micellar assemblies of triblock copolymers

Two reduction-cleavable ABA triblock copolymers possessing two disulfide linkages, PMMA-ss-PMEO₃MA-ss-PMMA and PDEA-ss-PEO-ss-PDEA were synthesized via facile substitution reactions from homopolymer precursors, where PMMA, PMEO₃MA, PDEA, and PEO represent poly(methyl methacrylate), poly(tri(ethylene glycol) monomethyl ether methacrylate, poly(2-(diethylamino)ethyl methacrylate), and poly(ethylene oxide), respectively. Spherical micelles were obtained through supramolecular self-assembly of these two triblock copolymers in aqueous solutions. The resultant micelles with abundant disulfide bonds could serve as soft templates and precisely accommodate gold nanoparticles in the core/shell interface as a result of the formation of Au-S bonds.     

CTAB-assisted fabrication of mesoporous composite consisting of wormlike aluminosilicate shell and ordered MSU-S core

Novel mesoporous composites comprised of aluminosilicate shell with wormhole framework structure and well-ordered MSU-S core have been firstly prepared via treatment of MSU-S with NaAlO₂ solution in the presence of cationic surfactant cetyltrimethylammonium bromide (CTAB). The obtained products were thoroughly characterized by XRD, HRTEM, N₂ sorption isotherm, TG-DSC, ²⁷Al MAS NMR and ²⁹Si MAS NMR, etc. Characterization results based on these techniques revealed that the introduction of CTAB during the treatment process played a crucial role in the formation of mesoporous composite, otherwise the parent ordered MSU-S would be completely destroyed. Furthermore, aluminum content in the final product determined by ICP and EDAX was significantly increased compared to the parent MSU-S, thus assuming that CTAB added in this modification process led a key role in the introduction of Al into the final solid via self-assembly with additionally added AlO₂⁻ and partly dissolved silicate species from the parent MSU-S particles. In addition, acidity and catalytic performance of the prepared mesoporous composite were also substantially improved in comparison to the parent MSU-S sample.     

Designed synthesis of ZnO/PEDOT core/shell hybrid nanotube arrays with enhanced electrochromic properties

Designed growth of zinc oxide (ZnO)/poly(3,4-ethylenedioxythiophene) (PEDOT) core/shell hybrid nanotube arrays has been achieved by electropolymerization technique. The ZnO/PEDOT hybrid nanotubes electropolymerized for 2000-second display enhanced electrochromic properties of the contrast ratio up to 31.3%, a lot higher than those of the pure PEDOT and ZnO/PEDOT hybrid nanorods. Moreover, the coloring efficiency of the hybrid nanotubes increases from 105.2 cm² C⁻¹ of ZnO/PEDOT hybrid nantotube with the electrodeposition time of 1000 seconds to 122.2 cm² C⁻¹ of 2000 seconds at 520 nm. Therefore, the hybrid composite nanotubes fabricated by the in situ electrodeposition techniques may demonstrate huge potential applications in energy-saving technologies such as smart windows.     

TiC/C core/shell nanowires arrays as advanced anode of sodium ion batteries

High-perfo rmance anodes of sodium ion batteries(SIBs)largely depends on rational architecture design and binder-free smart hybridization.Herein,we report TiC/C core/shell nanowires arrays prepared by a one-step chemical vapor deposition(CVD)method and apply it as the anode of SIBs for the first time.The conductive TiC core is intimately decorated with carbon shell.The as-obtained TiC/C nanowires are homogeneously grown on the substrate and show core/shell heterostructure and porous architecture with high electronic conductivity and reinforced stability.Owing to these merits,the TiC/C electrode displays good rate performance and outstanding cycling performance with a capacity of 135.3 mAh/g at 0.1 A/g and superior capacity retention of 90.14%after 1000 cycles at 2 A/g.The reported strategy would provide a promising way to construct binder-free arrays electrodes for sodium ion storage.     

Synthesis and properties of organo-fly ash/polyaniline with core/shell structure based on emulsion polymerization

Organo-fly ash(OFA) was prepared with pretreated fly ash(FA) and hexadecyltrimethyl ammonium bromide (HDTMAB),and the composites composed of OFA and polyaniline were obtained by emulsion polymerization at different OFA weight ratios(2.0 wt%,5.0 wt%,10.0 wt%,15.0 wt%and 20.0 wt%) in the presence of dodecylbenzenesulfonic acid as dopant and emulsifier.A polymerization procedure was supposed.The electrical conductivities of the composites were tested by the four-probe technique.The chemical structure and crystallinity of the composites were confirmed by FT-IR and X-ray diffraction,respectively.Morphologies of FA,OFA and the composites were observed by SEM.The element analysis was performed by energy dispersive spectrometry.The thermal stability of the composites was analyzed by TGA.The results showed that the electrical conductivity of the composites decreased with increasing the feed weight ratio of OFA,and the lowest value was 0.62 S/cm.HDTMAB and PAn were just adsorbed on the surface of FA and OFA,respectively according to the physical adsorption without destroying the crystalline structure of FA or OFA.The surface became smoother after organification of FA by using HDTMAB,and its content on FA surfaces was about 26.9 wt%.The core/shell structure of the composite was observed by SEM analysis.The composites showed a higher thermal stability than pure PAn by introduction of OFA into this polymerization system,the heat stability of PAn was increased by decreasing 31.8 wt%of weight loss after introducing 20 wt%of OFA.     

Comparison of different reactive organophosphorus flame retardant agents for cotton. Part II: Fabric flame resistant performance and physical properties

N-Methylol dimethylphosphonopropionamide (MDPA) is one of the most commonly used durable flame retardant agents for cotton. In our previous research, we developed a new flame retardant finishing system based on a hydroxy-functional organophosphorus oligomer (HFPO) and bonding agents, such as dimethyloldihydroxyethyleneurea (DMDHEU) and trimethylolmelamine (TMM). In this research, we compared the flame resistant performance as well as physical properties of the cotton fabric treated with these two flame retardant finishing systems. The cotton fabric treated with MDPA/TMM has a higher initial limiting oxygen index (LOI) than that of the fabric treated with HFPO/TMM due to higher nitrogen content in the system. The LOI of the cotton fabric treated with the HFPO and MDPA systems becomes identical when the treated fabric contains equal amount of phosphorus and nitrogen. The MDPA/TMM shows higher laundering durability on cotton than HFPO/TMM system. The fabric treated with HFPO/TMM and MDPA/TMM has low wrinkle resistance and low strength loss whereas the fabric stiffness significantly increases when the TMM concentration is increased.     

Effect of ethylene-acrylic acid copolymer on flame retardancy and properties of LLDPE/EAA/MH composites

Halogen-free flame retardant linear low density polyethylene (LLDPE)/ethylene-acrylic acid copolymer (EAA) blends were prepared in a melt process using magnesium hydroxide (MH) as flame retardant. The effect of EAA on flame retardancy and properties of LLDPE/EAA/MH composites was studied. The flammability of composites was investigated using Limiting Oxygen Index (LOI) and Cone calorimeter test. The results showed that the introduction of EAA into composites apparently increased LOI from 28% to 39%, meanwhile, reduced heat release rate (HRR) and smoke production rate (SPR) according to Cone calorimeter results, which was mainly due to the uniform dispersion of MH as a result of hydrogen bonding and acid-base reaction between MH and EAA. This improved interfacial adhesion was confirmed by Scanning Electronic Microscopy (SEM). Thermogravimetric analysis (TGA) showed that EAA could enhance the thermal oxidative stability of composites. It was attributed to the formation of a stable barrier to prevent the heat and mass transfer in fire, which was confirmed by the observation of fire performance with Cone calorimeter. The crystallization and rheological behaviour of composites were studied using Differential scanning calorimeter (DSC) and oscillatory rheological measurements. Mechanical test results indicated that the addition of EAA could increase the elongation at break and impact strength of composites.     

A vanillin-derived flame retardant based on 2-aminopyrimidine for enhanced flame retardancy and mechanical properties of epoxy resin

In order to give epoxy resin good flame retardance, a novel bio-based flame retardant based on 2-aminopyrimidine (referred to as VAD) was synthesized from renewable vanillin as one of the starting materials. Its structure was confirmed by NMR and mass spectra. The epoxy resins containing VAD were prepared by utilizing 4,4-diaminodiphenylmethane (DDM) as a co-curing agent, and their flame-retardant, mechanical and thermal properties and corresponding mechanisms were studied. VAD accelerated the cross-linking reaction of DDM and E51 (diglycidyl ether of bisphenol A). 12.5 wt% VAD made the epoxy resin achieve UL-94 V-0 rating and its limited oxygen index (LOI) value increase from 22.4% to 32.3%. The cone calorimetric testing results revealed the decline in the values of total heat release (THR) and peak of heat release rate (pk-HRR) and the obvious enhancement of residue yield. A certain amount of VAD enhanced the flame inhibition, charring and barrier effects, resulting in good flame retardance of the epoxy resin. Furthermore, the tensile strength, flexural strength and flexural modulus of the epoxy resin with 12.5 wt% loading of VAD were 6.5%, 14.9%, 15.2% higher than those of EP, indicating the strengthening effect of VAD. This work guarantees VAD to be a promising flame retardant for enhancing the fire retardancy of epoxy resin without compromising its mechanical properties.     

Using reversed-phase liquid chromatography to monitor the sizes of Au/Pt core/shell nanoparticles

This paper describes the use of reversed-phase liquid chromatography (RPLC) to rapidly characterize Au/Pt core/shell nanoparticles (NPs) produced through seed-assisted synthesis. We monitored the sizes of Au/Pt core/shell NPs by using a porous silica-based RPLC column (pore size: ca. 100 nm) and 30 mM sodium dodecyl sulfate in deionized water as the mobile phase; the plot of the retention time with respect to the logarithm of the size of the Au NPs was linear (R² = 0.997) for diameters falling in the range from 5.3 to 40.1 nm; from five consecutive runs, the relative standard deviations of these retention times were less than 0.4%. We used the optimal separation conditions of the RPLC system to study the effects that the rate of addition of the reducing agent and the volumes of the seed, shell precursor metal ion, and reducing agent solutions had on the sizes of the Au/Pt core/shell NPs. A good correlation existed between the sizes of the Au/Pt core/shell NPs determined through RPLC and those determined using transmission electron microscopy. RPLC appears to be a useful technique for monitoring the sizes of NPs and nanomaterials in general.     

Synergistic effects of layered double hydroxide with phosphorus-nitrogen intumescent flame retardant in PP/EPDM/IFR/LDH nanocomposites

<正>Synergistic effects of layered double hydroxide(LDH) with intumescent flame retardanct(IFR) of phosphorus-nitrogen (NP) compound in the polypropylene/ethylene-propylene-diene/IFR/LDH(PP/EPDM/IFR/LDH) nanocomposites and related properties were studied by X-ray diffraction(XRD),transmission electron microscopy(TEM),scanning electron microscopy(SEM),limiting oxygen index(LOI),UL-94 test,cone calorimeter test(CCT) and thermo-gravimetric analysis (TGA).The XRD and TEM results show that the intercalated and/or exfoliated nanocomposites can be obtained by direct melt-intercalation of PP/EPDM into modified LDH and that LDH can promote the IFR additive NP to disperse more homogeneously in the polymer matrix.The SEM results provide positive evidence that more compact charred layers can be obtained from the PP/EPDM/NP/LDH sample than those from the PP/EPDM/LDH and PP/EPDM/NP samples during burning.The LOI and UL-94 rating tests show that the synergetic effects of LDH with NP can effectively increase the flame retardant properties of the PP/EPDM/NP/LDH samples.The data from the CCT and TGA tests indicate that the PP/EPDM/NP/LDH samples apparently decrease the HRR and MLR values and thus enhance the flame retardant properties and have better thermal stability than the PP/EPDM/LDH and PP/EPDM/NP samples.     

Magnetite and magnetite/silver core/shell nanoparticles with diluted magnet-like behavior

In the present work is reported the use of the biopolymer chitosan as template for the preparation of magnetite and magnetite/silver core/shell nanoparticles systems, following a two step procedure of magnetite nanoparticles in situ precipitation and subsequent silver ions reduction. The crystalline and morphological characteristics of both magnetite and magnetite/silver core/shell nanoparticles systems were analyzed by high resolution transmission electron microscopy (HRTEM) and nanobeam diffraction patterns (NBD). The results of these studies corroborate the core/shell morphology and the crystalline structure of the magnetite core and the silver shell. Moreover, magnetization temperature dependent, M(T), measurements show an unusual diluted magnetic behavior attributed to the dilution of the magnetic ordering in the magnetite and magnetite/silver core/shell nanoparticles systems.     

Studies on melt flow properties during capillary extrusion of PP/Al(OH)3/Mg(OH)2 flame retardant composites

The apparent melt shear viscosity of polypropylene (PP) composites filled with aluminium hydroxide (Al(OH)₃) and magnesium hydroxide (Mg(OH)₂) was measured by means of a melt flow rate instrument under experimental conditions of temperature ranging from 170 to 195 °C and load varying from 2.16 to 12.5 kg, to identify the effects of particle size and content. The results showed that the melt shear flow of the composites obeyed the power law under the experimental conditions, the dependence of the melt apparent shear viscosity (η_a) on temperature was consistent with the Arrhenius equation, and the sensitivity of the η_a for the composite melts to temperature increased with addition of flame retardant. The η_a of the composites decreased with increasing apparent shear rate. The η_a increased with an increase of the content of flame retardant, but this rate of increase decreased with a rise of temperature or load. When the particle size of flame retardant was smaller than 5 μm, the η_a of the composites increased with increase of particle size of flame retardant, and then reduced with a further increase of particle size of flame retardant.