Thermal,morphological, mechanical and aging properties of polylactide blends with poly(ether urethane) based on chain-extension reaction of poly(ethylene glycol) using diisocyanate

Poly(ether urethane)s(PEU), including PEUI15 and PEUH15, were prepared through chain-extension reaction of poly(ethylene glycol)(PEG-1500) using diisocyanate as a chain extender, including isophorone diisocyanate(IPDI) and hexamethylene diisocyanate(HDI). These PEUs were used to toughen polylactide(PLA) by physical and reactive blending.Thermal, morphological, mechanical and aging properties of the blends were investigated in detail. These PEUs were partially compatible with PLA. The elongation at break of the reactive blends in the presence of triphenyl phosphate(TPP)for PLA with PEUH15 or PEUI15 was much higher than that of the physical blends. The aging test was carried out at-20 °C for 50 h in order to accelerate the crystallization of PEUs. The PEUs in the PLA/PEU blends produced crystallization and formed new phase separation with PLA, resulting in the declined toughness of blends. Fortunately, under the aging condition,although PEUH15 in blends could also form crystallization, the reactive blend of PLA/PEUH15/TPP(80/20/2) had higher toughness than the other blends. The elongation at break of PLA/PEUH15/TPP(80/20/2) dropped to 287% for the aging blend from 350% for the original blend. The tensile strength and modulus of PLA/PEUH15/TPP blend did not change obviously because of the crystallization of PEUH15.     

Synthesis and rheological properties of polylactide/poly(ethylene glycol) multiblock copolymers

Ring-opening polymerization of D,L-lactide was carried out in the presence of poly(ethylene glycol), using Zn powder as catalyst. The hydroxyl-capped PLA-PEG-PLA triblock copolymers were coupled with adipoyl chloride at different molar ratios under mild conditions. N-Dimethylaminopyridine (DMAP) was used as catalyst of the coupling reaction. The resulting PLA/PEG multiblock copolymers were characterized by various analytical techniques such as IR, 1H NMR, SEC, and DSC. Sol-gel transition properties of the multiblock copolymers were investigated by mechanical rheology. The data showed that the sol-gel transition temperature and the transition modulus increased with increasing molecular weight and the solution concentration of the multiblock copolymers. [Graph: see text] Variation of storage modulus (G') and loss modulus (G') as a function of temperature for a 20% sample of MB3.     

Improvement in Toughness of Polylactide by Melt Blending with Bio-based Poly（ester）urethane

Polylactide （PLA） was successfully toughened by blending with bio-based poly（ester）urethane （TPU） elastomers which contained bio-based polyester soft segments synthesized from biomass diols and diacids. The miscibility, mechanical properties, phase morphology and toughening mechanism of the blend were investigated. Both DSC and DMTA results manifested that the addition of TPU elastomer not only accelerated the crystallization rate, but also increased the final degree of crystallinity, which proved that TPU has limited miscibility with PLA and has functioned as a plasticizer. All the blend samples showed distinct phase separation phenomenon with sea-island structure under SEM observation and the rubber particle size in the PLA matrix increased with the increased contents of TPU. The mechanical property variation of PLA/TPU blends could be quantitatively explained by Wu＇s model. With the variation of TPU, a brittle-ductile transition has been observed for the TPU/PLA blends. When these blends were under tensile stress conditions, the TPU particles could be debonded from the PLA matrix and the blends showed a high ability to induce large area plastic deformation before break, which was important for the dissipation of the breaking energy. Such mechanism was demonstrated by tensile tests and scanning electron microcopy （SEM） observations.     

New architectures of poly(ethylene glycol) and poly(methylthiirane) in block copolymers

Two synthetic ways were experimented to prepare new architectures of block copolymers made of poly(ethylene glycol) (PEG) and poly(methylthiirane). The coupling of both blocks conveniently end-capped as well as anionic polymerization of methylthiirane initiated by PEG-thiols gave readily the copolymers. Their characterization by ¹H NMR, SEC and IR confirmed the expected structures.     

Y-shaped block copolymers of poly(ethylene glycol) and poly(N-isopropylacrylamide) synthesized by ATRP

Novel Y-shaped block copolymers of poly(ethylene glycol) and poly(N-isopropylacrylamide),PEG-b-(PNIPAM)_2,were successfully synthesized through atom transfer radical polymerization(ATRP).A difunctional macroinitiator was prepared by esterification of 2,2-dichloroacetyl chloride with poly(ethylene glycol) monomethyl ether(PEG).The copolymers were obtained via the ATRP of N-isopropylacrylamide(NIPAM) at 30℃with CuCl/Me_6TREN as a catalyst system and DMF/H_2O(v/v = 3:1) mixture as solvent.The resulting copo...     

Photocurable biodegradable poly(ɛ-caprolactone)/poly(ethylene glycol) multiblock copolymers showing shape-memory properties

Biodegradable multiblock copolymers were synthesized by a polycondensation of poly(ɛ-caprolactone) (PCL) diols of molecular weight (MW)=3,000 and poly(ethylene glycol)s (PEG) of MW=3,000 with 4,4′-(adipoyldioxy)dicinnamic acid (CAC) dichloride as a chain extender in diphenyl ether at 180 °C for 2 h, and were characterized by GPC, ¹H-NMR, FTIR, UV, DSC, and WAXS. These photosensitive copolymers were irradiated by a 400-W high-pressure mercury lamp (λ>280 nm) from 5–60 min to form a network structure. The gel contents increased with irradiation time, and attained ca. 90% after 60 min for all copolymers. The degree of swelling in a distilled water at ambient temperature, and the rate of degradation in a phosphate buffer solution (pH 7.2) at 37 °C increased with increasing PEG components. The shape-memory tests were performed by a cyclic thermomechanical experiments for the photocured CAC/PCL/PEG (75/25) films. The film with a gel content of 57% showed the best shape-memory property with strain fixity rate of 100% and strain recovery rate of 88%.     

Supercritical carbon dioxide assisted synthesis of amphiphilic graft copolymers based on poly(styrene-co-maleic anhydride) with methoxyl poly(ethylene glycol) side chains

Supercritical carbon dioxide（scCO₂） was used as a reaction medium in synthesizing amphiphilic graft copolymers composed of poly（styrene-co-maleic anhydride）（SMA） backbones and methoxyl poly（ethylene glycol）（MPEG） side chains via esterification.The synthesized copolymers were characterized by Fourier transform infrared spectroscopy（FTIR）,gel permeation chromatography（GPC）,¹H-NMR,thermo-gravimetric analysis（TGA） and differential scanning calorimetric analysis（DSC）.The gelation phenomenon was suppressed effectively by tuning reaction conditions.The influences of scCO₂ temperature and pressure on the conversion of anhydride were investigated.It was found that the highest conversion ratio occurred at 80℃under a constant pressure of 14 MPa or 26 MPa.With the increase of scCO₂ pressure,the conversion ratio increased first,and then leveled off.The conversion ratio of anhydride could be controlled by regulating the reaction conditions.It was also revealed that using low molecular weight MPEG brought a high conversion ratio of anhydride.     

Viscosity reduction and disentanglement in ultrahigh molecular weight polyethylene melt: Effect of blending with polypropylene and poly(ethylene glycol)

A significant reduction in melt viscosity of ultrahigh molecular weight polyethylene (UHMWPE) was obtained by blending with polypropylene (PP) and poly(ethylene glycol) (PEG). The mechanism of viscosity reduction was investigated from the view of disentanglement effect. Dynamic mechanical analysis indicated that the pseudoequilibrium modulus (E′) of UHMWPE/PP(80/20) blend in the rubbery plateau was much lower than that of UHMWPE. Accordingly, the calculated entanglement density (ν_e) of UHMWPE/PP (80/20) blend was smaller than that of UHMWPE. Further reduction in E′ and ν_e of the blend was obtained by the incorporation of 1 phr PEG. Slow DSC analysis showed that the high temperature endotherm and exotherm for UHMWPE at slow temperature ramp diminished and increased, respectively when 5 phr PEG was added. It also revealed that the entanglement level of UHMWPE decreased with the addition of a small amount of PEG.     

Crystallization behavior and biodegradation of poly(3-hydroxybutyrate) and poly(ethylene glycol) multiblock copolymers

Block copolymerization by using isocyanates is an effective method for incorporating PHB and PEG because it can prepare copolymers with good properties, such as toughness, strength, and so on. In this study, we adopted soil suspension system to estimate the biodegradability of a series of PHB/PEG multiblock copolymers with different compositions and block lengths. In the degradation process, the changes in weight loss, molecular weight, and tensile strength were periodically measured to determine the biodegradability, and the surface morphology was also observed by SEM. In contrast to pure PHB, the weight loss of the copolymer was relatively lower. On the other hand, the tensile strength and molecular weight experienced apparent decrease, and for BHG1000-3-1, they reached 46.7% and 77.7% of the initial value, respectively. SEM observation showed that the surface was covered with numerous erosion pits. All these indicate that the degradation indeed took place and long-chain molecules have been hydrolyzed into shorter ones. The crystallization behavior was also investigated by DSC and WAXD. The results showed that both the segments, PEG and PHB, can form crystalline phases at lower PHB contents ranging from 29% to 44%, and when PHB component was more than 60%, only PHB phase can crystallize.     

New approach on the development of plasticized polylactide (PLA): Grafting of poly(ethylene glycol) (PEG) via reactive extrusion

In this work, new ways of plasticizing polylactide (PLA) with low molecular poly(ethylene glycol) (PEG) were developed to improve the ductility of PLA while maintaining the plasticizer content at maximum 20 wt.% PLA. To this end, a reactive blending of anhydride-grafted PLA (MAG-PLA) copolymer with PEG, with chains terminated with hydroxyl groups, was performed. During the melt-processing, a fraction of PEG was grafted into the anhydride-functionalized PLA chains. The role of the grafted fraction was to improve the compatibility between PLA and PEG. Reactive extrusion and melt-blending of neat and modified PLA with PEG did not induce any dramatic drop of PLA molecular weight. The in situ reactive grafting of PEG into the modified PLA in PLA/PEG blends showed a clear effect on the thermal properties of PLA. It was demonstrated by DSC that the mobility gained by PLA chains in the plasticized blends yielded crystallization. The grafting of a fraction of PEG into PLA did not affect this process. However, DSC results obtained after the second heating showed an interesting effect on the T_g when 20 wt.% PEG were melt blended with neat PLA or 10 wt.% MAG-PLA. In the latter case, the T_g displayed by the reactive blend was shifted to even lower temperatures at around 14 °C, while the T_g of neat PLA and PLA blended with 20 wt.% PEG was around 60 and 23 °C, respectively. Regarding viscoelastic and viscoplastic properties, the presence of MAG-PLA does not significantly influence the behavior of plasticized PLA. Indeed, with or without MAG-PLA, elastic modulus and yield stress decrease, while ultimate strain increases with the addition of PEG into PLA.     

Determination of poly(ethylene glycol)s by both normal-phase and reversed-phase modes of high-performance liquid chromatography

A normal-phase HPLC system using an amino column has been developed to characterise oligomers of poly(ethylene glycol)s (PEGs) of average M_r 400 to 2000 with derivatisation by dinitrobenzoate. Normal-phase HPLC with gradient elution using ternary solvents of hexane, dichloromethane and methanol has produced a baseline resolution for oligomers of PEG 400, 600 and 1000, while PEG 1000 and 2000 were analysed by using binary solvents of acetonitrile and water. Mixtures of PEGs have been determined by these HPLC systems. PEG 400 in a textile finish has also been determined with satisfactory recovery. It has been found that the hydroxyl group of solvents in normal-phase HPLC plays an important role in resolution and retention of PEG oligomers. Derivatisation efficiency for PEGs by dinitrobenzoyl chloride and quantitative determination of derivatised PEGs by HPLC have been studied. A reversed-phase (RP) mode of HPLC was examined for determination of PEG 400 oligomers. The normal-phase system provided greater resolution for oligomers of PEGs.     

Segmented block copolymers of poly(ethylene glycol) and poly(ethylene terephthalate)

A new series of segmented copolymers were synthesized from poly(ethylene terephthalate) (PET) oligomers and poly(ethylene glycol) (PEG) by a two‐step solution polymerization reaction. PET oligomers were obtained by glycolysis depolymerization. Structural features were defined by infrared and nuclear magnetic resonance (NMR) spectroscopy. The copolymer composition was calculated via ¹H NMR spectroscopy. The content of soft PEG segments was higher than that of hard PET segments. A single glass‐transition temperature was detected for all the synthesized segmented copolymers. This observation was found to be independent of the initial PET‐to‐PEG molar ratio. The molar masses of the copolymers were determined by gel permeation chromatography (GPC). © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 4448–4457, 2004     

Synthesis and properties of polymer brushes composed of poly(diphenylacetylene) main chain and poly(ethylene glycol) side chains

Novel cylindrical polymer brushes consisting of poly(diphenylacetylene) main chain and poly(poly(ethylene glycol) methyl ether monomethacrylate) (PPEGMA) side chains were synthesized by the diphenylacetylene macromonomer or side chain initiated atom transfer radical polymerization (ATRP) of poly(ethylene glycol) methyl ether monomethacrylate (PEGMA) from an bromo isobutyryl-bearing poly(diphenylacetylene) (poly(BrDPA)) method. The diphenylacetylene macromonomer, namely, DPA-PPEGMA, were prepared by the ATRP of PEGMA from bromo isobutyryl-bearing diphenylacetylene. DPA-PPEGMA was polymerized successfully with WCl₆-Ph₄Sn catalyst to give high molecular weight polymer brushes poly(DPA-PPEGMA). Meanwhile, polymer brushes (PDPA-g-PPEGMA) were obtained by ATRP of PEGMA from poly(BrDPA). The molecular weight of the side chains of PPEGMA could be controlled simply by modulating the ATRP time. The macromonomer and polymer brushes are soluble in nonpolar solvents such as toluene and chloroform. The polymers of poly(BrDPA) and poly(DPA-PPEGMA) absorb in the longer wavelength region, with two peaks at around 370 and 414 nm. The polymers are thermally stable and exhibit double crystallization and melting peaks during the cooling and heating scans.     

Crystallization of photo-chain extended poly(ethylene glycol)

Coumarin-functionalized poly(ethylene glycol) (PEG) monols and diols were isothermally crystallized at temperatures between 20 and 35 °C before and after exposure to approximately 110 J cm⁻² of ultra-violet A (λ > 300 nm, UVA) irradiation. Irradiation dimerized the coumarin groups and chain-extended the coumarin-functionalized PEG oligomers. The higher molecular weights reduced the crystal growth rate by as much as 50% compared to the non-irradiated coumarin-functionalized PEG oligomers under ambient crystallization conditions. Hoffman’s kinetic nucleation theory was utilized to evaluate the types of nucleation that occurred for the coumarin-functionalized PEG diols (COU-PEG-COU). Crystallization regimes II and III were observed for the coumarin-modified PEG oligomers before and after exposure to UVA light.     

Complement activation by sulfonated poly(ethylene glycol)-acrylate copolymers through alternative pathway

Previously, novel poly(ethylene glycol) (PEG) and sulfonated PEG acrylate (PEG-SO₃A/OA) copolymers were prepared as coating and/or blending materials for biomedical applications. Surfaces modified with copolymers exhibited increased anti-coagulation properties and decreased plasma adsorption level due to increased hydrophilic properties and reorientation characteristics of PEG/PEG-SO₃A chains in water phase. As continuation study, anti-complement effects of PEG-SO₃/OA copolymers were investigated in vitro, and compared with those of low-density polyethylene (LDPE) and PEG/OA. C3 activation by PEG-SO₃/OA samples was lower than that by PEG/OA samples, which was attributed to decreased surface nucleophile level of samples. PEG-SO₃/OA samples increased inhibition of Bb production, resulting in decreased C5 activation. Owing to reduced activations of C3 and C5, PEG-SO₃/OA samples markedly decreased SC5b-9 levels in plasma.     

Photocrosslinked hydrogels based on copolymers of poly(ethylene glycol) and lysine

A group of new, water-soluble poly(ether-urethane)s, derived from poly(ethylene glycol) and the amino acid L -lysine, provide pendent carboxylic acid groups along the polymer backbone at regular intervals. The carboxylic acid groups were utilized for the attachment of acrylate and methacrylate pendent chains (hydroxyethyl acrylate, hydroxyethyl methacrylate, aminoethyl methacrylate, and aminoethyl methacrylamide), leading to functionalized polymers. The pendent chains were attached via ester and/or amide bonds having different degrees of hydrolytic stability. The attachment reactions proceeded with high yields (up to 95%). The functionalized polymers were subsequently photopolymerized (UV irradiation) to obtain crosslinked hydrogels. Crosslinked membranes with the highest degree of mechanical strength were obtained when the crosslinking reaction was performed in dioxane with benzoin methyl ether (0.1 wt %) as the initiator. the crystallinity, thermomechanical properties, and hydrolytic stability of the crosslinked membranes were studied. All membranes were transparent and highly swellable (equilibrium water content: 64–88%). The tensile strength in the swollen state ranged from 0.15 to 1.09 MPa. Under physiological conditions (phosphate buffered water, 0.1M, pH 7.4, 37°C) the hydrolytic stability of the hydrogels varied depending on the bonds used in the attachment of the acrylate pendent chains: Hydrogels with hydroxyethyl acrylate pendent chains dissolved within 30 days, while hydrogels containing aminoethyl methacrylamide pendent chains remained unchanged throughout a 30 day period. Using high molecular weight FITC-dextrans as model compounds, complete release from the swollen hydrogels required between 60 and 150 h. Overall, the evaluation of poly(ethylene glycol)-lysine derived, photocrosslinked hydrogels indicated that these materials provide a range of potentially useful properties. © 1994 John Wiley & Sons, Inc.     

An improved interfacial coacervation technique to fabricate biodegradable nanocapsules of an aqueous peptide solution from polylactide and its block copolymers with poly(ethylene glycol)

ABA block copolymers of polylactide and poly(ethylene glycol) as amphiphilic bioabsorbable polymers were synthesized by the ring-opening polymerization of dl- lactide onto poly(ethylene glycol) (PEG 2000 or PEG 6000) and their structures were characterized on the basis of proton NMR. Biodegradable nanocapsules of an aqueous insulin solution were prepared from the block copolymers and polylactide by an improved interfacial coacervation technique. The results showed that the diameters of the nanocapsules were mainly dependent on the ratio of the two chains in the block polymers. The size of the nanocapsules decreased with an increase in the amount of surfactant used. More insulin solution resulted in an enlargement of the nanocapsules in diameter. In an optimum condition, biodegradable nanocapsules could be achieved with a size around 250 nm with a narrow distribution. The encapsulation percentages of insulin were larger in the nanocapsules from the PEG 2000 copolymers than in those from the PEG 6000 analogs and changed with the ratios of the blocks in the block copolymers. Received: 17 July 2000 Accepted: 24 November 2000     

Preparation, characterization and biocompatibility of poly(ethylene glycol)-poly(n-butyl cyanoacrylate) nanocapsules with oil core via miniemulsion polymerization

A new type of nanocapsules with an oil core, coated by poly(ethylene glycol) (PEG) was designed. The loading efficiency and the biocompatibility of the polymeric nanocapsules were evaluated when it was used as a carrier for hydrophobic agent paclitaxel. The nanocapsules were synthesized through miniemulsion polymerization of butylcyanoacrylate (BCA) with PEG as initiator. The particle size and zeta potential of nanocapsules were influenced by the PEG content in the polymerization system. Fourier transform infrared (FTIR) spectra and ¹H NMR demonstrated the chemical coupling between PEG and poly(butylcyanoacrylate) (PBCA). Thermal characteristics of the copolymer were investigated by differential scanning calorimetry (DSC). The encapsulation efficiency increased concurrently with the increase of the PEG content in the system. The hemolytic assay and the cytotoxicity measurement showed that the PEG coating could significantly reduce the hemolytic potential and cytotoxicity of the nanocapsules. The results showed that the PEG-PBCA nanocapsules could be an effective carrier for hydrophobic agents.     

An analysis of the complexation between poly(aspartic acid) and poly(ethylene glycol)

The compatibility between poly(aspartic acid) and poly(ethylene glycol) for the formation of an interpolymer complex (IPC) was investigated by dynamic rheology and evaluation of zeta potential values. The homogeneity of the realized IPC was observed by near infrared chemical imagistic (NIR-CI) technique. The data were sustained and underlined by the assessment of the compatibility between the polymeric compounds.     

Determination of poly(ethylene glycol) 300 in long chain free fatty acid mixtures by reversed-phase high-performance liquid chromatography

A rapid sensitive method has been developed for the detection and quantitation of poly(ethylene glycol) 300 (PEG 300) in long-chain free fatty acid mixtures that requires minimal sample preparation. The PEG 300 was separated from the free fatty acids by RP-HPLC using a water–tetrahydrofuran gradient. PEG and the free fatty acids were detected using evaporative light scattering detection. The minimum detectable level of PEG in a free fatty acid mixture was 0.0125%.