Die Additionsmethode in der Photometrie

Standard curves for the photometric determination of Cu²⁺, Ni²⁺, Co²⁺, Fe³⁺ and Cr³⁺, using the colour of their aqueous solutions, are not suitable if the composition of the solutions is unknown. It is more useful, to determine the respective absorption coefficient of the ions in the present solution by adding an known amount of the element. Fe³⁺ is reduced to Fe²⁺, then the absorption of Fe²⁺ is measured at 920 nm. Cr³⁺ must be oxidized to CrO ₄ ^2? and then be reduced again. The standard deviation of the procedures described exceeds 1% only in a few cases. The possibility to determine in the same manner two or three compounds in presence of each other is mentioned.     

Quantum dot-based "turn-on" fluorescent probe for detection of zinc and cadmium ions in aqueous media

Health or environmental issue caused by abnormal level of metal ions like Zn²⁺ or Cd²⁺ is a worldwide concern. Developing an inexpensive and facile detection method for Zn²⁺ and Cd²⁺ is in urgent demand. Due to their super optical properties, fluorescent quantum dots (QDs) have been developed as a promising alternative for organic dyes in fluorescence analysis. In this study, a CdTe QDs-based sensitive and selective probe for Zn²⁺ and Cd²⁺ in aqueous media was reported. The proposed probe worked in fluorescence “turn-on” mode. The initial bright fluorescence of CdTe QDs was effectively quenched by sulfur anions (S²⁻). The presence of Zn²⁺ (or Cd²⁺) can “turn-on” the weak fluorescence of QDs quenched by S²⁻ due to the formation of ZnS (or CdS) passivation shell. Under optimal conditions, a good linear relationship between the fluorescence response and concentration of Zn²⁺ (or Cd²⁺) could be obtained in the range from 1.6 to 35 μM (1.3–25 μM for Cd²⁺). The limit of detection (LOD) for Zn²⁺ and Cd²⁺ were found to be 1.2 and 0.5 μM, respectively. Furthermore, the present probe exhibited a high selectivity for Zn²⁺ and Cd²⁺ over other metal ions and was successfully used in the detection of Zn²⁺ or Cd²⁺ in real water samples.     

Metal Ion Interaction of Two New Tritopic N2O13 Macrobicycles with B15C5 Moieties in Acetonitrile Solution

The synthesis of two new tritopic crown ligands (L1 and L2) bearing two benzo-15-crown-5 lateral moieties linked through a dibenzo-trioxa chain together with their interaction with metal ions, in acetonitrile and acetonitrile–water (50%, v/v) solutions is reported. The influence of K⁺, Na⁺, Li⁺, Ca²⁺, Ba²⁺, Cu²⁺, Zn²⁺, Cd²⁺, Pb²⁺ and Al³⁺, on the spectroscopic properties of these diaza-polyoxa ligands was investigated by absorption spectrophotometry and in some cases by fluorescence emission spectroscopy. Coordination with alkaline (Na⁺, K⁺ and Li⁺) and alkaline earth (Ca²⁺and Ba²⁺) metal ions is assumed to be weak with both macrobicyclic ligands, while the interaction with both imine and amine derivatives causes a minor effect in the absorption spectra. Coordination with Cu²⁺, Zn²⁺ and Pb²⁺ in acetonitrile solution causes a major change in the absorption spectra of the chromophores. In the case of Cu²⁺, addition of the metal to L1 or L2 leads to a blue–violet complex in solution with an absorbance maximum centred at 590 nm. Interaction of the Schiff-base L1 with Pb²⁺ leads to a short wavelength shift in the absorption bands, comparable with the ZnL1 complex. Presence of transition metal ions such as Co²⁺, Ni²⁺and Cd²⁺ do not remarkably affect the absorption spectra of L1 and L2 in solution. Trivalent aluminium has a modest effect in the absorption bands of both N₂O₁₃ donor set bismacrocyclic ligands. The fluorescence study of L2 in the presence of Na⁺, K⁺, Ca²⁺, Ba²⁺, Co²⁺, Cu²⁺, Ni²⁺, Pb²⁺ and Al³⁺shows that Cu²⁺, Pb²⁺ and Al³⁺ complexes form non-fluorescent complexes.     

Qualitative and quantitative 1H NMR spectroscopy for determination of divalent metal cation concentration in model salt solutions,food supplements,and pharmaceutical products by using EDTA as chelating agent

This paper introduces an ¹H NMR method to identify individual divalent metal cations Be²⁺, Mg²⁺, Ca²⁺, Sr²⁺, Zn²⁺, Cd²⁺, Hg²⁺, Sn²⁺, and Pb²⁺ in aqueous salt solutions through their unique signal shift and coupling after complexation with the salt of ethylenediaminetetraacetic acid (EDTA). Furthermore, quantitative determination applied for the divalent metal cations Ca²⁺, Mg²⁺, Hg²⁺, Sn²⁺, Pb²⁺, and Zn²⁺ (limit of quantification: 5–22 μg/ml) can be achieved using an excess of EDTA with aqueous model salt solutions. An internal standard is not required because a known excess of EDTA is added and the remaining free EDTA can be used to recalculate the quantity of chelated metal cations. The utility of the method is demonstrated for the analysis of divalent cations in some food supplements and in pharmaceutical products.     

Dielectric dispersion in optical electron transfer in solution

Dielectric dispersion causes the outer-sphere reorganization free energy to vary with photon energy in optical electron transfer. The resulting distortion of the spectral response for photoelectron emission may yield misleading evidence about the emission yield versus photon energy relationship. Dispersion is taken into account in the calculation of emission threshold energies and the correlation between optical and thermal electron transfer. Results are given for V²⁺, Cr²⁺, Mn²⁺, Fe²⁺, Co²⁺, Fe(CN)₆^4?.     

Optimal Geometrical Configuration of Cobalt Cations in Spinel Oxides to Promote Oxygen Evolution Reaction

MgCo₂O₄, CoCr₂O₄, and Co₂TiO₄ were selected, where only Co³⁺ in the center of octahedron (Oh), Co²⁺ in the center of tetrahedron (Td), and Co²⁺ in the center of Oh, can be active sites for the oxygen evolution reaction (OER). Co³⁺(Oh) sites are the best geometrical configuration for OER. Co²⁺(Oh) sites exhibit better activity than Co²⁺(Td). Calculations demonstrate the conversion of O* into OOH* is the rate‐determining step for Co³⁺(Oh) and Co²⁺(Td). For Co²⁺(Oh), it is thermodynamically favorable for the formation of OOH* but difficult for the desorption of O₂. Co³⁺(Oh) needs to increase the lowest Gibbs free energy over Co²⁺(Oh) and Co²⁺(Td), which contributes to the best activity. The coexistence of Co³⁺(Oh) and Co²⁺(Td) in Co₃O₄ can promote the formation of OOH* and decrease the free‐energy barrier. This work screens out the optimal geometrical configuration of cobalt cations for OER and gives a valuable principle to design efficient electrocatalysts.     

A New Mode of Energy Transfer between Mn2+ and Eu2+ in Nitride‐Based Phosphor SrAlSi4N7 with Tunable Light and Excellent Thermal Stability

In this work, reciprocal energy transfer between Mn²⁺ and Eu²⁺ ions in nitride SrAlSi₄N₇ has been found and investigated in detail. In contrast to Mn²⁺‐ and Eu²⁺‐activated oxide‐based phosphors, the red light centered at 608 nm is ascribed to 4f–5d transitions of Eu²⁺ ions and Mn²⁺‐activated SrAlSi₄N₇ emits a cyan light peaking at 500 nm. Additionally, the special broad excitation band of SrAlSi₄N₇:Mn²⁺ centered at 362 nm has been covered by that of Eu²⁺ ions ranging from 300 to 550 nm. The overlap of the energy level of Mn²⁺ and Eu²⁺ ions creates the conditions for reciprocal energy transfer between Eu²⁺ and Mn²⁺ ions. A series of SrAlSi₄N₇:0.002 Mn²⁺,xEu²⁺ (0≤x≤005) with tunable light emission have been synthesized and the decay curves of samples prove the reciprocal occurrence of the energy transfer between Mn²⁺ and Eu²⁺ ions. This mode of energy transfer not only prevents the loss of energy, but also improves the thermal stability, and the intensity of SrAlSi₄N₇:Mn²⁺,Eu²⁺ at 150 °C is still beyond 92 % of the initial intensity. The results provide a new mode of energy transfer, which is expected to reduce the drawbacks existing in energy transfer.     

Rapid capillary zone electrophoresis method for the determination of metal cations in beverages

A rapid and reliable capillary zone electrophoresis method for the determination of inorganic cations was developed. The complete separation of K⁺, Ba²⁺, Ca²⁺, Na⁺, Mg²⁺, Mn²⁺, Ni²⁺, Cd²⁺, Li⁺ and Cu²⁺ can be achieved in 4 min with a simple electrolyte composed by 10 mM imidazole as the carrier buffer and background absorbance provider and acetic acid as the complexing agent (pH 3.60). Injection was performed hydrostatically by elevating the sample at 10 cm for 30 s. The running voltage was +25 kV at room temperature. Indirect UV-absorption detection was achieved at 185 nm. The detection limit was in the range between 0.06 mg/l (Mg²⁺) and 0.57 mg/l (K⁺) and the quantification limits ranged from 0.10 mg/l (Ni²⁺) to 0.80 mg/l (Cu²⁺). The calibration graphs were linear in the concentration range from the quantification limit till at least 1 g/l in K⁺, 10 mg/l in Ba²⁺, Ca²⁺, Mg²⁺, Mn²⁺, Ni²⁺ and Cd²⁺, 40 mg/l in Na⁺ and 12 mg/l in Li⁺ and Cu²⁺. The repeatability, intraday and interday analysis were ≤1.55% and ≤3.64% for migration time and ≤3.38% and ≤3.63% for peak area. The method developed has been applied to several beverage samples with only a simple dilution and filtration treatment of the sample. The proposed method is simple, fast, cheap and it is achieved with common products in either laboratory. For these reasons, it is a very useful method for routine analysis.     

The mechanism of electroreduction of nitrobenzene and 3-nitropyridine in DMF in the presence of divalent cations

The differences in electrochemical behaviour of nitrobenzene and 3-nitropyridine connected with a change of supporting electrolyte are discussed. It is shown that in the presence of alkaline earch metal cations a deposit of composition (NB^?. Me²⁺) is formed at the electrode surface. The cations: Ba²⁺, Ca²⁺ and Mg²⁺ cause the instability of the nitrobenzene radical anion formed in the first electroreduction step. It was found that in the presence of Ba²⁺ and Ca²⁺ the NOB/NO^?. couple is stabilized.     

Role of Calcium in Photodynamically Induced Cell Damage of Human Fibroblasts

Photodynamically induced changes in the cytoplasmic free calcium concentration ([Ca²⁺]_i) and its role in cell damage were investigated in human skin fibroblasts using confocal laser microscopy. Fluorescence and absorbance spectrophotometry measurements indicate that the photosensitizer aluminum phthalocyanine tetrasulfonate (AlPcS₄) binds to the plasma membrane and only after irradiation is able to enter the cells, causing massive morphologic alterations. Upon irradiation of sensitizer-treated cells, the increase in [Ca²⁺]_i is related to the amount of light and extracellular [Ca²⁺]_e. The increase in [Ca²⁺]_i was substantially reduced in the absence of [Ca²⁺]_e. Cell damage or death after photodynamic treatment was prevented and shifted toward higher fluence by increasing [Ca²⁺]_i at high [Ca²⁺]_e and was greater at low [Ca²⁺]_e. Application of Ca²⁺ channel blockers, such as Co²⁺, Cd²⁺ or verapamil, could not prevent the increase of [Ca²⁺]_i. Our results indicate that activation of the photosensitizer, AlPcS₄, causes an influx of Ca²⁺, which protects cells from photodamage. At low [Ca²⁺]_e and high fluence values, release of Ca²⁺ from internal stores probably as a protective measure occurs in order to increase the [Ca²⁺]_i.     

Energy transfer from UO22+ to Sm3+ in phosphate glass

Energy transfer from UO₂²⁺ to Sm³⁺ is described. The transfer efficiencies are calculated from the decrease of donor luminescence and lifetimes and from the increase of the acceptor fluorescence. It is shown that the transfer is nonradiative. The energy transfer efficiencies are greater when the donor is excited at higher energy levels due to stronger overlap between electronic levels of donor UO₂²⁺ and acceptor Sm³⁺. From the comparison of energy transfer efficiencies from UO₂²⁺ to Sm³⁺ and Eu³⁺ it is deduced that the overlap between excitation levels of donor and acceptor is a sufficient condition for the transfer.     

A hybrid mesoporous material functionalized by 1,8-naphthalimide-base receptor and the application as chemosensor and absorbent for Hg2+ in water

A novel hybrid material (SBA-P1) is prepared through the functionalization of mesoporous silica (SBA-15) with a 1,8-naphthalimide-based dye by sol-gel reaction. The characterization results of elemental analysis (EA), X-ray powder diffractometer (XRD) and spectroscopic methods demonstrate the fluorescence dye P1 is successfully grafted onto the inner surface of SBA-15 and the organized structure is preserved. SBA-P1 can detect Hg²⁺ with high selectivity to Cu²⁺, Zn²⁺, Cd²⁺, Pb²⁺, Mn²⁺, Ni²⁺, Co²⁺, Ag⁺, Cr³⁺, and Mg²⁺, Ca²⁺, Li⁺, Na⁺, K⁺ in water and sensitivity to environmentally relevant mercury in complex natural samples. The quenching fluorescence detection is also reversible by treating with EDTA/base. Furthermore, its fluorescence intensity keeps stable in the physiologically relevant pH range. The extraction ability of SBA-P1 is also estimated by inductively coupled plasma source mass spectrometer (ICP), showing that approximately 90% of the Hg²⁺ ion is extracted. These results imply that the hybrid material has potential application for sensing and removing of Hg²⁺ ions in waste water and working as toxicide for acute mercury poisoning.     

Time-resolved fluorescence microscopy for quantitative Ca2+ imaging in living cells

Calcium (Ca²⁺) is a ubiquitous intracellular second messenger and involved in a plethora of cellular processes. Thus, quantification of the intracellular Ca²⁺ concentration ([Ca²⁺]_i) and of its dynamics is required for a comprehensive understanding of physiological processes and potential dysfunctions. A powerful approach for studying [Ca²⁺]_i is the use of fluorescent Ca²⁺ indicators. In addition to the fluorescence intensity as a common recording parameter, the fluorescence lifetime imaging microscopy (FLIM) technique provides access to the fluorescence decay time of the indicator dye. The nanosecond lifetime is mostly independent of variations in dye concentration, allowing more reliable quantification of ion concentrations in biological preparations. In this study, the feasibility of the fluorescent Ca²⁺ indicator Oregon Green Bapta-1 (OGB-1) for two-photon fluorescence lifetime imaging microscopy (2P-FLIM) was evaluated. In aqueous solution, OGB-1 displayed a Ca²⁺-dependent biexponential fluorescence decay behaviour, indicating the presence of a Ca²⁺-free and Ca²⁺-bound dye form. After sufficient dye loading into living cells, an in situ calibration procedure has also unravelled the Ca²⁺-free and Ca²⁺-bound dye forms from a global biexponential fluorescence decay analysis, although the dye's Ca²⁺ sensitivity is reduced. Nevertheless, quantitative [Ca²⁺]_i recordings and its stimulus-induced changes in salivary gland cells could be performed successfully. These results suggest that OGB-1 is suitable for 2P-FLIM measurements, which can gain access to cellular physiology.

A reactive electrode (reactrode) for the voltammetric determination of heavy metals in laboratories and for use as a passive monitor in remote analysis

The use of a reactive electrode (reactrode) consisting of graphite, a solid ion exchanger (HYPHAN) and paraffin for the batch analysis of Cd²⁺, Cu²⁺, Pb²⁺ and Hg²⁺ in aqueous samples and as a passive monitor for these metal ions is described. The metal ions are accumulated on the reactrode surface at an open-circuit potential in an ion-exchange reaction. After the accumulation, the ion exchanger-bonded metal ions are reduced to the metals which remain on the electrode surface. In a following step, the metals are anodically dissolved which is recorded by differential-pulse voltammetry. The 3s detection limits for the analysis of drinking water are: 1.1×10^-7 mol/l for Pb²⁺, 5×10^-8 mol/l for Hg²⁺ and 2.4×10^-7 mol/l for Cu²⁺.The reactrode developed can be used for the passive monitoring of heavy metals in aqueous streams if the reactrode is mounted in a wall-jet cell which is part of a flow-through system. Using this arrangement, it has been possible to determine Hg²⁺, Cu²⁺ and Pb²⁺ in drinking water after 20 hours of accumulation.     

Metal ion complexation in acetonitrile by upper-rim allyl-substituted, di-ionized calix[4]arenes bearing two dansyl fluorophores

The influence of Li⁺, Na⁺, K⁺, Rb⁺, Cs⁺, Mg²⁺, Ca²⁺, Sr²⁺, Ba²⁺, Ag⁺, Cd²⁺, Co²⁺, Fe²⁺, Hg²⁺, Mn²⁺, Pb²⁺, Zn²⁺ and Fe³⁺ on the spectroscopic properties of two dansyl (1-dimethylaminonaphthalene-5-sulfonyl) groups linked to the lower rims of a series of three, structurally related, di-ionized calix[4]arenes is investigated by means of absorption and emission spectrophotometry. Di(tetramethylammonium) salts of the di-ionized ligands, L, L1, and L2, which differ in having no, two and four allyl groups, respectively, on the upper rim of the calix[4]arene scaffold, are utilized for the spectrofluorimetric titration experiments in MeCN. On complexation by alkaline earth metal cations, the emission spectra undergo marked red shifts and quenching of the dansyl fluorescence. These effects are weaker with alkali metal cations. Transition metal cations and Pb²⁺ interact strongly with the ligands. In particular, Fe³⁺, Hg²⁺ and Pb²⁺ cause greater than 99% quenching of the dansyl fluorescence.     

Polarographic studies on tributyltin oxide in dichloromethane and tetrahydrofuran with application to antifouling paint

In the presence of tributyltin oxide, (Bu₃Sn)₂O, an oxidation process is observed at mercury electrodes in non-aqueous solvents. On the polarographic time-scale, the oxidation involves the mercury electrode and is believed to occur according to the following reaction scheme: 2Bu₃SnOSnBu₃ + 2Hg?[Bu₃SnHgSnBu₃]²⁺ + Hg (OSnBu₃)₂ + 2e^? Hg(OSnBu₃)₂+2Hg?[BuSnHgSnBu₃]²⁺ + 2HgO+2e^? to give the overall process Bu₃SnOSnBu₃+2Hg?[Bu₃SnHgSnBu₃]²⁺ + HgO+2e^?. On the time scale of controlled-potential electrolysis, [Bu₃SnHgSnBu₃]²⁺ is unstable and additional electron transfer occurs. The oxidation process forms the basis of a specific high-performance liquid chromatographic method for the determination of tributylin oxide in antifouling paint. A static mercury drop electrode in the hanging drop mode is used as an amperometric detector in a flow-cell configuration.     

Supramolecular chemosensor for selective detection of iron in aqueous medium

We have successfully developed a ‘turn-on’ colorimetric chemosensor for Fe³⁺ based on 1,10-phenanthroline. An amide derivative of 1,10-phenanthroline 4 was developed for the selective recognition of Fe³⁺ over Co²⁺, Cr³⁺, Cu²⁺, Mn²⁺, Ni²⁺, Ag⁺ and Zn²⁺ and could measure Fe³⁺ concentration in the range of 15–210 μM by UV–vis spectroscopy. Moreover, the addition of Fe³⁺ to a colourless solution of 4 turned its colour to light pink, indicating that 4 is capable of detecting Fe³⁺ by the naked eye. Compound 4 exhibits a major absorption band centred at 268 which shifted to 278 nm after addition of Fe³⁺, and a shoulder band around 514 nm was also observed. The complexation of Fe³⁺ with 4 was analysed at a different pH and favourable binding was observed at pH 6.2.     

A new phenothiazine-based fluorescence sensor for imaging Hg2+ in living cells

A new phenothiazine-based sensor PHE-Ad for monitoring Hg²⁺ has been designed and synthesized based on the intramolecular charge transfer (ICT) mechanism. The probes were characterized by FTIR, ¹H NMR, and HRMS, and their optical properties were detected by UV and FL. It's showed the probes detection of Hg²⁺ compared to other metal ions (Mg²⁺, Cu²⁺, Hg²⁺, Ag⁺, Co²⁺, Cr³⁺, Al³⁺, Ni²⁺, Zn²⁺, Ca²⁺, Fe³⁺, Fe²⁺, K⁺, Na⁺, and Cd²⁺) based on the test results. Besides, the detection limits were determined to be 2.12 × 10⁻⁸ M through the standard curve plot. In addition, sensor PHE-Ad shows high selectivity and sensitivity for Hg²⁺ with a fast response in a suitable pH range. Furthermore, taking into account its good “turn-on” fluorescent sensing behavior and low cell cytotoxicity, PHE-Ad was successfully applied to detect and image Hg²⁺ in real water samples and living cells, which shows great potentials for application in environmental and biological systems.     

Oberflächenzusammensetzung,Löslichkeit und Ionenaktivitätsprodukt von Calcit in fremdionenhaltigen Lösungen

Surface Composition, Solubility, and the Ion Activity Product of Calcite in Solutions with Auxiliary Ions Using the method of simultaneous ion and isotope exchange the chemical composition of the surface layer of calcite powder in equilibrium with solutions of varying Me/Ca molar ratios is determined (Me = Mg²⁺, Co²⁺, Ni²⁺, and Fe²⁺ ions). The ion exchange isotherms show a marked bend in the surface reactivity when a surface molar ration of ～1 and ～3 is reached. The solubility of calcite initially decreases on the addition of Co²⁺ or Ni²⁺ ions to the solution whereas it increases in the presence of Mg²⁺ or Fe²⁺ ions. The activity product of the pseudo compound, Ca_xMe_(1–x)CO₃, decreases in the Ni²⁺, Co²⁺ or Fe²⁺ exchange experiments, however, it increases considerably in those with Mg²⁺ ions.     

Luminescence properties of Eu2+, Sn2+, and Pb2+ in SrB6O10 and Sr1 − xMnxB6O10

The luminescence properties of Eu²⁺, Sn²⁺, and Pb²⁺ in SrB₆O₁₀ have been studied both at room-temperature and liquid-helium temperature and the decay times of Sn²⁺ and Pb²⁺ in this matrix have been measured and analyzed. According to the emission spectrum of Eu²⁺ there seems to be three different cation sites in SrB₆O₁₀. Europium, tin, and lead were also used as sensitizers for Mn²⁺ and the energy transfer processes were characterized. Eu²⁺-Mn²⁺ energy transfer was inefficient due to the transfer within different Eu²⁺ centers. The sensitization action of Sn²⁺ and Pb²⁺ on Mn²⁺ was different because lead-lead energy transfer occurs (even at 4.2 K) but tin-tin transfer can be neglected. A fast diffusion model for the Pb²⁺ system is suggested.