Ultradeep Hydrodesulfurization of Dibenzothiophene (DBT) Derivatives over Mo-Sulfide Catalysts Supported on TiO2-Coated Alumina Composite

The present paper reviews in detail the different studies now being conducted by our research team concerning the ultradeep hydrodesulfurization (HDS) of dibenzothiophene (DBT) derivatives over Mo/TiO₂ and Mo/TiO₂–Al₂O₃ catalysts. First, a detailed characterization of Mo/TiO₂ (P-25 Degussa, 50 m²/g) catalysts prepared by equilibrium adsorption technique shows that Mo- species are highly and uniformly dispersed on the surface of titania up to 6.6 wt% MoO₃ loading. Above this value, some aggregation of Mo occurs, leading to the formation of bulk MoO₃. Below 6.6 wt% MoO₃ loading, the Raman spectroscopy data of the calcined samples show that the supported Mo-species possess a highly distorted octahedral MoO₆ structure. TiO₂–Al₂O₃ composites were prepared by chemical vapor deposition (CVD) using TiCl₄ as a precursor. Using several characterization techniques, we demonstrated that the support composite presents a high dispersion of TiO₂ over -Al₂O₃ without forming precipitates up to ca. 11 wt% loading. Moreover, the textural properties of the composite support are comparable to those of alumina. Under the present sulfidation conditions (673 K, 5%H₂S/95%H₂), Mo-species supported on TiO₂ are better sulfided than on alumina, as demonstrated using XPS. This can be attributed to the relatively lower interaction between Mo-species and titania. The state of sulfide species supported on the composite support can be considered as a transition state between TiO₂ and Al₂O₃. However, at relatively higher TiO₂ loadings (ca. 11 wt%), Mo/TiO₂–Al₂O₃ catalysts exhibit sulfidability similar to that of Mo/TiO₂. The HDS tests conducted in both the laboratory and in industry show that sulfide catalysts supported on TiO₂–Al₂O₃ (ca. 11 wt% TiO₂) are more active than those supported on TiO₂ or Al₂O₃.     

TiO2–carbon nanotube heterojunction arrays with a controllable thickness of TiO2 layer and their first application in photocatalysis

TiO₂–carbon nanotube (CNT) heterojunction arrays on Ti substrate were fabricated by a two-step thermal chemical vapor deposition (CVD) method. CNT arrays were first grown on Ti substrate vertically, and then a TiO₂ layer, whose thickness could be controlled by varying the deposition time, was deposited on CNTs. Measured by electrochemical impedance spectroscopy (EIS), the thickness of the TiO₂ layer could affect the photoresponse ability significantly. About 100 nm thickness of the TiO₂ layer proved to be best for efficient charge separation among the tested samples. The optimized TiO₂–CNT heterojunction arrays displayed apparently higher photoresponse capability than that of TiO₂ nanotube arrays which was confirmed by surface photovoltage (SPV) technique based on Kelvin probe and EIS. In the photocatalytic experiments, the kinetic constants of phenol degradation with TiO₂–CNT heterojunctions and TiO₂ nanotubes were 0.75 h⁻¹ (R² = 0.983) and 0.39 h⁻¹ (R² = 0.995), respectively. At the same time, 53.7% of total organic carbon (TOC) was removed with TiO₂–CNT heterojunctions, while the removal of TOC was only 16.7% with TiO₂ nanotubes. These results demonstrate the super capability of the TiO₂–CNT heterojunction arrays in photocatalysis with comparison to TiO₂-only nanomaterial.     

Fabrication and characterization of TiO<Subscript>2</Subscript>–SiO<Subscript>2</Subscript> composite nanoparticles and polyurethane/(TiO<Subscript>2</Subscript>–SiO<Subscript>2</Subscript>) nanocomposite films

TiO₂–SiO₂ composite nanoparticles were prepared by a sol–gel process. To obtain the assembly of TiO₂–SiO₂ composite nanoparticles, different molar ratios of Ti/Si were investigated. Polyurethane (PU)/(TiO₂–SiO₂) hybrid films were synthesized using the “grafting from” technique by incorporation of modified TiO₂–SiO₂ composite nanoparticles building blocks into PU matrix. Firstly, 3-aminopropyltriethysilane was employed to encapsulate TiO₂–SiO₂ composite nanoparticles’ surface. Secondly, the PU shell was tethered to the TiO₂–SiO₂ core surface via surface functionalized reaction. The particle size of TiO₂–SiO₂ composite sol was performed on dynamic light scattering, and the microstructure was characterized by X-ray diffraction and Fourier transform infrared. Thermogravimetric analysis and transmission electron microscopy (TEM) employed to study the hybrid films. The average particle size of the TiO₂–SiO₂ composite particles is about 38 nm when the molar ratio of Ti/Si reaches to1:1. The TEM image indicates that TiO₂–SiO₂ composite nanoparticles are well dispersed in the PU matrix.     

Preparation of Ag3PO4/TiO2(B) Heterojunction Nanobelt with Extended Light Response and Enhanced Photocatalytic Performance

Photocatalytic degradation, as an emerging method to control environmental pollution, is considered one of the most promising environmental purification technologies. As Tibet is a region with some of the strongest solar radiation in China and even in the world, it is extremely rich in solar energy resources, which is ideal for applying photocatalytic technology to its ecological environment protection and governance. In this study, Na₂Ti₃O₇ nanobelts were prepared via a hydrothermal method and converted to TiO₂∙xH₂O ion exchange, which was followed by high-temperature calcination to prepare TiO₂(B) nanobelts (“B” in TiO₂(B) means “Bronze phase”). A simple in situ method was used to generate Ag₃PO₄ particles on the surface of the TiO₂ nanobelts to construct a Ag₃PO₄/TiO₂(B) heterojunction composite photocatalyst. By generating Ag₃PO₄ nanoparticles on the surface of the TiO₂(B) nanobelts to construct heterojunctions, the light absorption range of the photocatalyst was successfully extended from UV (ultraviolet) to the visible region. Furthermore, the recombination of photogenerated electron–hole pairs in the catalyst was inhibited by the construction of the heterojunctions, thus greatly enhancing its light quantum efficiency. Therefore, the prepared Ag₃PO₄/TiO₂(B) heterojunction composite photocatalyst greatly outperformed the TiO₂(B) nanobelt in terms of photocatalytic degradation.     

p-Aminophenylacetic acid-mediated synthesis of monodispersed titanium oxide hybrid microspheres in ethanol solution

Monodispersed TiO₂ hybrid microspheres were prepared via the hydrolysis of titanium isopropoxide (TTIP) in ethanol solution containing p-aminophenylacetic acid (APA). The effects of the APA:TTIP molar ratio, water content, reaction time and reaction temperature on the morphology of the resultant spheres were investigated. The products were characterized by scanning electron microscopy, transmission electron microscopy, Fourier transform infrared spectroscopy, thermogravimetric analysis, and X-ray diffraction. It was demonstrated that the diameters of the resultant TiO₂ spheres could be tuned in the range of 380–800 nm by changing the APA:TTIP molar ratio (1:3 to 3:1) and water content (1–3 v/v%) in the reaction medium, and that increasing the APA:TTIP molar ratio led to larger TiO₂ hybrid spheres while increasing the water content decreased their size. The loading content of APA in the hybrid spheres could reach 20 wt.% as they were prepared with the APA:TTIP ratio of 3:1. The possible formation mechanism of the hybrid spheres was also investigated. It was found that APA slowed down the hydrolysis rate of the titanium precursor so that resulted in the formation of the TiO₂ spheres. In addition, the APA present in TiO₂ spheres acted as a reducing agent to in situ convert HAuCl₄ into metallic Au on the surface of the TiO₂ spheres. The catalytic activity of the resultant Au/APA–TiO₂ composite was examined using transfer hydrogenation of phenylacetone with 2-propanol, and it was indicated that the catalyst displayed high efficiency for this reaction.     

Sol-Gel Poly-Component Nano-Sized Oxide Powders

Nano-sized, amorphous and monodispersed poly-component powders in the Al₂O₃–TiO₂–MgO and Al₂O₃–TiO₂–SiO₂ systems have been obtained by the sol-gel method. These powders have been characterized by XRD, IR spectroscopy, DTA/TGA and EDAX spectrometry. This last method confirmed the composition of the ternary powders, which are formed during the gelation process.The powders were tested as precursors for obtaining advanced ceramics, as tialite, Al₂TiO₅. The samples prepared with powders obtained by sol-gel method have shown a high reactivity, and the formation of tialite was improved.     

Photocatalytic activities of C–N-doped TiO2 nanotube array/carbon nanorod composite

A C–N-doped TiO₂ nanotube (NT)/carbon nanorod composite is fabricated by chemical vapor deposition (CVD). Carbon nanorods are grown from the TiO₂ NTs, and partly graphitized, while TiO₂ is in the mixture of anatase and rutile. The C–N doping shifts the absorption edge of TiO₂ NTs to the visible light region; the formed carbon nanorods promote the charge carrier transfer from the TiO₂ surface to the electrolyte. Under the simulated solar light irradiation, the C–N-doped TiO₂ NTs show higher photocatalytic activity in the degradation of methyl orange (MO) than the undoped TiO₂ NTs.     

Photocatalytic hydrogen evolution over mesoporous TiO2/metal nanocomposites

Na⁺ complex with the dibenzo-18-crown-6 ester was used as a template to synthesize mesoporous titanium dioxide with the specific surface area 130–140 m²/g, pore diameter 5–9 nm and anatase content 70–90%. The mesoporous TiO₂ samples prepared were found to have photocatalytic activity in Cu^II, Ni^II and Ag^I reduction by aliphatic alcohols. The resulting metal–semiconductor nanostructures have remarkable photocatalytic activity in hydrogen evolution from water–alcohol mixtures, their efficiency being 50–60% greater than that of the metal-containing nano-composites based on TiO₂ Degussa P25.The effects of the thermal treatment of mesoporous TiO₂ upon its photocatalytic activity in hydrogen production were studied. The anatase content and pore size were found to be the basic parameters determining the photoreaction rate. The growth of the quantum yield of hydrogen evolution from TiO₂/Ag⁰ to TiO₂/Ni⁰ to TiO₂/Cu⁰ was interpreted in terms of differences in the electronic interaction between metal nanoparticles and the semiconductor surface. It was found that there is an optimal metal concentration range where the quantum yield of hydrogen production is maximal. A decrease in the photoreaction rate at further increment in the metal content was supposed to be connected with the enlargement of metal nanoparticles and deterioration of the intimate electron interaction between the components of the metal–semiconductor nanocomposites.     

Au-TiO2/Chit modified sensor for electrochemical detection of trace organophosphates insecticides

In this paper, Au–TiO₂/Chit modified electrode was prepared with Au–TiO₂ nanocomposite (Au–TiO₂) and Chitosan (Chit) as a conjunct. The Au–TiO₂ nanocomposite and the films were characterized by electrochemical and spectroscopy methods. A set of experimental conditions was also optimized for the film's fabrication. The electrochemical and electrocatalytic behaviors of Au–TiO₂/Chit modified electrode to trace organophosphates (OPs) insecticides such as parathion were discussed in this work. By differential pulse voltammetry (DPV) measurement, the current responses of Au–TiO₂/Chit modified electrode were linear with parathion concentration ranging from 1.0 ng/ml to 7.0 × 10³ ng/ml with the detection limit of 0.5 ng/ml. In order to evaluate the performance of the detection system, we also examined the real samples successfully in this work. It exhibited a sensitive, rapid and easy-to-use method for the fast determination of trace OPs insecticides.     

Synthesis of Spherical Titanium Dioxide Particles by Homogeneous Precipitation in Acetone Solution

Titania powders were synthesized by thermal hydrolysis of titanium tetrachloride in a mixed solvent was studied. The dielectric constant was tuned by regulating the acetone/water volume ratio (R/H ratio) and temperature of the solvent. Hydroxypropyl cellulose (HPC) was used as a steric dispersant. The synthesis were carried out at R/H ratios of 0–4, temperatures of 70–90°C, TiCl₄ concentrations of 0.05–0.2 M, HPC concentrations of 0–5 × 10^–3 g/cm³, and synthesis times of 15–60 min. The TiO₂ particles obtained at an R/H ratio of 0, i.e., pure water system, were fine and agglomerated. In contrast, the TiO₂ particles prepared at an R/H ratio of 3 were uniform and spherical. The TiO₂ particle size increased with increasing TiCl₄ concentration. The synthesis temperature did not influence the particle size, but greatly influenced the morphologyof the TiO₂. Adding HPC to the solution yielded more uniform and spherical particles. In addition, the synthesis time should be longer than 30 min to obtain the most uniform and spherical particles. The dielectric constant of the acetone-water mixed solvent at 28 gave the most uniform and spherical TiO₂ particles. The powders prepared at the condition of 0.1 M TiCl₄, R/H ratio of 3, HPC concentration of 0.001 g/cm³, temperature of 70°C, and synthesis time of 1 h exhibited the most uniform and spherical morphology. The as-synthesized powder was anatase and retained the phase below 400°C. It transformed to the rutile phase after calcination at 700°C.     

Reaction of oxygen with adsorbed hydrogen species of a reduced Pt/TiO2 catalyst

Reaction of oxygen with the adsorbed hydrogen species of Pt/TiO₂ catalysts reduced in the temperature range of RT-773 K has been studied by temperature-programmed oxidation (TPO). It is obtained that the Pt-assisted reaction of oxygen with both the surface hydroxy groups and titanium hydride species occurs in the temperature range of 320–450 K; direct oxidation of the surface hydrogen species takes place on the surface of TiO₂ in the temperature range of 500–600 K; and oxygen reacts with the stored hydrogen species in the sublayer and bulk of the TiO₂ support when the temperature was increased to above 600 K.     

Formation of appropriate sites on nanofiltration membrane surface for binding TiO2 photo-catalyst: Performance, characterization and fouling-resistant capability

Titanium dioxide (TiO₂) nanoparticles were assembled on the surface of nanofiltration blend membrane. For settling TiO₂ on the membrane surface, two membrane categories were used: (i) unmodified polyethersulfone (PES)/polyimide (PI) blend membrane, and (ii) –OH functionalized PES/PI blend membrane with different concentrations of diethanolamine (DEA). These membranes were radiated by UV light after TiO₂ depositing with different concentrations. 15 min immersion in colloidal suspension and 15 min UV irradiation with 160 W lamps were used for modification. The modification resulted in the formation of a photo-catalytic property with enhanced membrane hydrophilicity. The self-assembly of TiO₂ nanoparticles was established through coordinance bonds with –OH functional groups on the membrane surface. A comparison between the UV irradiated TiO₂ deposited blend membrane and deposited-functionalized blend membranes showed that –OH groups originate excellent adhesion of TiO₂ nanoparticles on the membrane surface, increase reversible deposition, and diminish irreversible fouling. The membranes were characterized using SEM, FTIR, EDX, contact angle, cross flow filtration, and antifouling measurements. SEM images show that the presence of –OH groups on the DEA-modified membrane surface is the main parameter for extra uniformly settlement of TiO₂ nanoparticles on the membrane surface. This procedure is a superior technique for modification of PES/PI nanofiltration membranes to enhance water flux and minimization membrane fouling.     

Hydrothermal synthesis of mesostructured nanocrystalline TiO2 in an ionic liquid–water mixture and its photocatalytic performance

Anatase mesostructured TiO₂ nanocrystalline was prepared in a mixture of 1-butyl-3-methyl-imidazolium tetrafluoroborate (BMIM⁺BF₄⁻) ionic liquid and water by a low temperature hydrothermal method. The obtained materials were characterized by X-ray powder diffraction (XRD), transmission electron microscopy (TEM) and N₂ adsorption–desorption. The existence of BMIM⁺BF₄⁻ enhanced the polycondensation and crystallization rate, which encouraged the formation of anatase crystal. The TiO₂ particles were thermally very stable and thus resistant to anatase-rutile phase transformation during calcination at high temperatures. The anatase TiO₂ showed high photocatalytic activity in the degradation of p-chlorophenol than that of the commercially available TiO₂, Degussa P25. After 2 h reaction under the UV-irradiation of 250 W, the removing rate of p-chlorophenol was up to 96.3%.     

Anodic composite deposition of RuO2·xH2O–TiO2 for electrochemical supercapacitors

This communication demonstrates the first work on anodic composite deposition of oxide nanocomposites. Rutile TiO₂ nanoflowers with an average petal size of ca. 10 nm in diameter and 100 nm in length were synthesized from a TiCl₃ solution purged with air at 25 °C for 12 days prior to the composite deposition. Hydrous ruthenium oxide (RuO₂·xH₂O) and TiO₂ nanoflowers were composite-deposited onto Ti substrates for supercapacitors. In comparing with RuO₂·xH₂O deposits, RuO₂·xH₂O–TiO₂ nanocomposites with a highly porous nature exhibit the weakly mass-dependent specific capacitance and high-power capacitive characteristics.     

Synthesis of bimodal porous structured TiO2 microsphere with high photocatalytic activity for water treatment

In this work bimodal structured titanium dioxide (TiO₂) microsphere has been prepared from commercial TiO₂ powder and nano-sized titania gel via sol–gel spray-coating technique. Crystallization and transformation behavior of titania gel were investigated. The results revealed that the crystallization and transformation of anatase particles were substantially affected by the concentration of solvent and calcination temperature. Anatase crystallite size of 10 nm was obtained at mole ratio of solvent/precursor 50/1 and calcination temperature of 450 °C. The prepared nano-sized titania gel was embedded within the core (commercial TiO₂, P25) during the spraying process. The prepared TiO₂ microsphere was characterized using X-ray diffractometer (XRD), scanning electron microscope (SEM), field emission electron microscope (FESEM) and micropore analysis. The photocatalytic activity was monitored by following the degradation of phenol with activity benchmarked against commercial P25 (Degussa). The increase of photocatalytic activity of TiO₂ microsphere was attributed to the nano-sized anatase crystallite which has been incorporated into the TiO₂ microsphere.     

Fabrication of a graphene–cuprous oxide composite

A composite of graphene–cuprous oxide (Cu₂O) was prepared using copper acetate-adsorbed graphene oxide (GO) sheets as precursors. In this composite, in-situ formed Cu₂O particles were derived from the adsorbed copper acetate which attached to graphene sheets and prevented the aggregation of the reduced graphene oxide sheets. The as-synthesized Cu₂O crystals were cube-like particles distributed randomly on the sheets due to the template effect of GO, consequently forming a graphene–Cu₂O cubes composite. A preliminary study on the electrochemical behavior of the graphene–Cu₂O composite used as anode material for lithium ion batteries was carried out.     

Preparation and properties of SiO2-TiO2 thin films from silicic acid and titanium tetrachloride

The preparation of SiO₂-TiO₂ thin films by the sol-gel method using silicic acid and titanium tetrachloride as starting materials was studied. The homogeneous sols were obtained by the condensation reaction of silicic acid with titanium tetrachloride in methanol-tetrahydrofuran. The dipcoating of slide glasses and silicon wafers followed by heat treatment gave oxide thin films of 88–93% transmittance, 3000–4500 Å thickness, and 1.45–1.80 refractive index, depending on heat-treatment temperature and TiO₂ content. FT-IR measurement showed that the Si-O-Ti bond is formed even in the sol and films. The variations of film thickness and refractive index on transformation from the gels into the oxides were found to be quite low.     

Photocatalytic Activity and Characterization of the Sol-Gel Derived Pb-Doped TiO2 Thin Films

Photocatalytically active Pb-doped TiO₂ thin films were prepared on a soda-lime glass substrate by sol-gel dip-coating technique using TiO₂ sols containing lead(II) nitrate. The thin films were characterized by X-ray photoelectron spectroscopy (XPS), atomic force microscopy (AFM), UV-VIS spectroscopy and X-ray diffraction (XRD). A shift of the UV-VIS absorption towards longer wavelengths was observed, which indicated a decrease in the band-gap of TiO₂ upon Pb doping. XRD results showed both pure and Pb-doped TiO₂ thin films were polycrystalline, anatase type, and oriented predominantly to the (101) plane. A slight shift in the d-spacing for the Pb-doped film indicated the incorporation of Pb into the TiO₂ lattice to form Pb _x Ti_1–x O₂ solid solution. AFM results showed Pb-doped TiO₂ thin films were composed of larger TiO₂ particles and had rougher surface, compared with un-doped TiO₂ thin films. XPS results showed that except for the enrichment of Pb near the surface, Pb exists in the forms of Pb _x Ti_1–x O₂ and PbO. Dimethyl-2,2-dichlorovinyl phosphate (DDVP) was efficiently degraded in the presence of the Pb-doped TiO₂ thin films by exposing the insecticide solution to sunlight. The mechanism of photocatalytic activity enhancement of the Pb-doped TiO₂ thin films was discussed.     

Temperatures and kinetics of anatase to rutile transformation in doped TiO<Subscript>2</Subscript> heated in microwave field

The influence of aliovalent ions such as Mn, Cr, Fe, Mo, and V on the temperature and kinetics of anatase to rutile phase transformation in TiO₂ heated in microwave field was studied in this work. The results indicated that heat treatment method and dopants considerably affected the anatase-to-rutile phase transition temperature and kinetics of transformation. The activation energy for anatase to rutile transformation of TiO₂ derived from the isothermal data was found to be 328.4 kJ mol^–1, which was considerably reduced by the addition of dopants in TiO₂ matrix. The activation energy for Mo, Mn and V doped samples was 252.0, 101.3 and 96.4 kJ mol^–1, respectively.     

Pulsed laser-induced oxygen deficiency at TiO2 surface: Anomalous structure and electrical transport properties

We have studied pulsed laser-induced oxygen deficiencies at rutile TiO₂ surfaces. The crystal surface was successfully reduced by excimer laser irradiation, and an oxygen-deficient TiO_2−δ layer with 160 nm thickness was formed by means of ArF laser irradiation at 140 mJ/cm² for 2000 pulses. The TiO_2−δ layer fundamentally maintained a rutile structure, though this structure was distorted by many stacking faults caused by the large oxygen deficiency. The electrical resistivity of the obtained TiO_2−δ layer exhibited unconventional metallic behavior with hysteresis. A metal–insulator transition occurred at 42 K, and the electrical resistivity exceeded 10⁴ Ω cm below 42 K. This metal–insulator transition could be caused by bipolaronic ordering derived from Ti–Ti pairings that formed along the stacking faults. The constant magnetization behavior observed below 42 K is consistent with the bipolaronic scenario that has been observed previously for Ti₄O₇. These peculiar electrical properties are strongly linked to the oxygen-deficient crystal structure, which contains many stacking faults formed by instantaneous heating during excimer laser irradiation.