Preparation and modification of collagen-based porous scaffold for tissue engineering

In the effort to generate cartilage tissues using mesenchymal stem cells, porous scaffolds with prescribed biomechanical properties were prepared. Scaffolds with interconnected pores were prepared via lyophilisation of frozen hydrogels made from collagen modified with chitosan nanofibres, hyaluronic acid, copolymers based on poly(ethylene glycol) (PEG), poly(lactic-co-glycolic acid) (PLGA), and itaconic acid (ITA), and hydroxyapatite nanoparticles. The modified collagen compositions were cross-linked using N-(3-dimethylamino propyl)-N′-ethylcarbodiimide hydrochloride (EDC) combined with N-hydroxysuccinimide (NHS) in water solution. Basic physicochemical and mechanical properties were measured and an attempt to relate these properties to the molecular and supermolecular structure of the modified collagen compositions was carried out. Scaffolds containing hydrophilic chitosan nanofibres showed the highest swelling ratio (SR = 20–25) of all the materials investigated, while collagen modified with an amphiphilic PLGA-PEG-PLGA copolymer or functionalised with ITA exhibited the lowest swelling ratio (SR = 5–8). The best resistance to hydrolytic degradation was obtained for hydroxyapatite containing scaffolds. On the other hand, the fastest degradation rate was observed for synthetic copolymer-containing scaffolds. The results showed that the addition of hydroxyapatite or hyaluronic acid to the collagen matrix increases the rigidity in comparison to the collagen-chitosan scaffold. Collagen scaffold modified with hyaluronic acid presented reduced deformation at break while the presence of hydroxypatatite enhanced the scaffold deformation under tensile loading. The tensile elastic modulus of chitosan nanofibre collagen scaffold was the lowest but closest to the articular cartilage; however, the strength and deformation to failure increased up to 200 %. Presented at the 1st Bratislava Young Polymer Scientists Workshop, Bratislava, 20–23 August 2007.     

Physical–chemical characterization studies of ketoprofen for orodispersible tablets

The objective of this work was to investigate the thermal, morphological, spectroscopic and cytotoxicity of hydroxyapatite–wollastonite powders obtained via sol–gel synthesis and of biocomposites chitosan–hydroxyapatite–wollastonite. A mixture of wollastonite, calcium nitrate tetrahydrate and ammonium dihydrogen phosphate with a ratio of 1:2:1.2 or 2:2:1.2, respectively, was produced following drying and heat treatment where the final composite was macerated. These powders were added to a chitosan solution where it was further dried and neutralized. The ceramic loads were used in various ratios. The materials were characterized by TG, DSC, DRX, MEV, FTIR and cytotoxicity. Based on the studied properties, it can be said that the sol–gel process proved to be effective in obtaining hydroxyapatite–wollastonite powders. By TG, it was verified that the thermal stability of the powders increased when a greater percentage of wollastonite was used. For biocomposites with higher percentages of load, there was increase in thermal stability, probably attributed to the higher compaction of the biocomposites when compared to the pure. By DSC, there was a tendency of displacement of the endothermic and exothermic peaks, suggesting that the biocomposite with higher load has greater capacity of retention and interaction stronger with molecules of water, but also has greater thermal stability. The samples present biomaterial potential with prospects of endodontic use, which showed cell viability in L929 fibroblast cell culture above 70.00%.     

Biocomposites of nanohydroxyapatite with collagen and poly(vinyl alcohol)

Biocomposites of hydroxyapatite, HAp, in conjunction with various binders including poly(vinyl alcohol), PVA, and collagen have the potential of serving in various tissue engineering applications, such as in bone repair and reconstruction tasks, especially if the nanoparticles of hydroxyapatite are used. Here, hydroxyapatite nanoparticles (n-HAp) were synthesized at the ultimate size range of 10-50 nm and then incorporated into PVA or in situ synthesized in collagen/PVA. The biocomposites of HAp with PVA exhibited relatively high elasticity (as revealed by the linear viscoelastic material functions, characterized upon small-amplitude oscillatory shear) especially upon cryogenic treatment. The incorporation of the collagen into the PVA/HAp biocomposite provided internal porosity to the biocomposite with the pores in the 50-100 nm range for collagen/HAp and 50-500 nm for the collagen/HAp/PVA.     

Water clustering by the surface of a vitreous body/hydroxyapatite nanocomposite

Low-temperature ¹H NMR spectroscopy was used to examine the effect of external factors (temperature and environment) on the hydrate properties of nanocomposite powder materials based on hyaluronic acid and hydroxyapatite. Thermodynamic parameters of layers of strongly and weakly bound water and the nanocompositewater interface energy were determined.     

Modulation of metal-azolate frameworks for the tunable release of encapsulated glycosaminoglycans

Glycosaminoglycans (GAGs) are biomacromolecules necessary for the regulation of different biological functions. In medicine, GAGs are important commercial therapeutics widely used for the treatment of thrombosis, inflammation, osteoarthritis and wound healing. However, protocols for the encapsulation of GAGs in MOFs carriers are not yet available. Here, we successfully encapsulated GAG-based clinical drugs (heparin, hyaluronic acid, chondroitin sulfate, dermatan sulfate) and two new biotherapeutics in preclinical stage (GM-1111 and HepSYL proteoglycan) in three different pH-responsive metal-azolate frameworks (ZIF-8, ZIF-90, and MAF-7). The resultant GAG@MOF biocomposites present significant differences in terms of crystallinity, particle size, and spatial distribution of the cargo, which influences the drug-release kinetics upon applying an acidic stimulus. For a selected system, heparin@MOF, the released therapeutic retained its antithrombotic activity while the MOF shell effectively protects the drug from heparin lyase. By using different MOF shells, the present approach enables the preparation of GAG-based biocomposites with tunable properties such as encapsulation efficiency, protection and release.

Clinical and pre-clinical GAG-based biotherapeutics were encapsulated within three metal-azolate frameworks (ZIF-8, ZIF-90, and MAF-7). The resulting MOF biocomposites show different loading capacity, biopreservation properties and release profiles.     

Enhanced interfacial adhesion,mechanical, and thermal properties of natural flour-filled biodegradable polymer bio-composites

This study examined the interfacial adhesion, mechanical, and thermal properties of compatibilizing agent-treated and non-treated biocomposites as a function of the type of compatibilizing agent. The tensile strength, interfacial adhesion, and heat deflection temperature (HDT) of maleic anhydride-grafted poly(butylene succinate) (PBS-MA) and maleic anhydride-grafted poly(lactic acid) (PLA-MA)-treated biocomposites are greater than those of untreated maleic anhydride-grafted poly(styrene-b-ethylene-co-butylene-b-styrene) triblock copolymer (SEBS-MA) and maleic anhydride-grafted polypropylene (MAPP)-treated biocomposites. The storage modulus (E′) values and the tan δ_max temperatures (T _g) of PBS-MA and PLA-MA-treated biocomposites were slightly higher than that of the untreated biocomposites.     

Synthesis and characterization of grafted nanohydroxyapatites using functionalized surface agents

Synthetic hydroxyapatite, HA [Ca10(PO4)6(OH)2], is a bioactive material that is chemically similar to biological apatite, the mineral phase of bone (a nanocomposite material). Synthetic biocomposites, comprising a polymer and hydroxyapatite that are used for bone replacement, have limitations when loaded under fatigue in that the weak mechanical bond between the two phases can result in failure at the interface. Chemical coupling of the HA and polymer matrix may provide a means of improving the interfacial bonding between the polymer and HA phases. Herein, we report our first steps toward developing chemically coupled nano-biocomposites via a two-step process. We describe the synthesis and characterization of surface-grafted hydroxyapatite (SG-HA), which possesses a reactive C=C functional group. In future work, we will report on the second step, namely the coupling of this functional group to a polymer by a copolymerization reaction to give a chemically coupled nano-biocomposite. The SG-HA reported herein was characterized by a range of methods including 31P and 13C magic-angle spinning (MAS)-NMR, Fourier transform infrared (FTIR), and Raman spectroscopy.     

The comparison of physic-chemical properties of chitosan/collagen/hyaluronic acid composites with nano-hydroxyapatite cross-linked by dialdehyde starch and tannic acid

Scaffolds based on chitosan, collagen and hyaluronic acid, cross-linked by dialdehyde starch with hydroxyapatite were obtained with the use of the freeze-drying method. Scaffolds were cross-linked by tannic acid or dialdehyde starch addition. Composites were characterized by different analyses, e.g. SEM images, porosity, density, liquid uptake, and mechanical tests. In addition, the adhesion and proliferation of human osteosarcoma SaOS-2 cells were examined on the obtained scaffolds.The results showed that the properties of the scaffolds based on chitosan, collagen, and hyaluronic acid can be modified by cross-linkers addition. The compressive modulus for the scaffolds cross-linked by dialdehyde starch was higher than for those cross-linked by tannic acid. The porosity of scaffolds cross-linked by starch was higher than those in which tannic acid was applied. However, the former presented lower density. SEM images showed the homogeneous scaffold structure with interconnected pores. Scaffolds cross-linked by tannic acid exhibited higher biocompatibility than those cross-linked by dialdehyde starch. However, the results showed that both scaffolds, cross-linked by dialdehyde starch and by tannic acid can provide the support required in tissue engineering and regenerative medicine. The scaffolds presented here may be easily operated to fit such small bone defects without causing adverse reactions.     

Mechanical and thermal characterization of sisal fiber reinforced polylactic acid composites

The advantages of green composites are including, but not limited to their environmental friendly nature, lightweight, reduction of production energy and costs, and recyclability. This work focuses on the mechanical, thermal, and dynamic mechanical properties of biocomposites. For that purpose, biosourced polymers were used, namely polylactic acid (PLA) and sisal fiber, and biocomposites were extruded and then injection molded with different contents of sisal fibers (5%, 10%, 15%). The results show that the increase of the rate of reinforcement improves the mechanical and dynamic mechanical properties of the biocomposites made. By the increase of the sisal fiber content, the degree of crystallinity of the matrix was increased from 47% to 61%, as sisal fibers were acted as a nucleating agent for the PLA.     

Concentration and degradation of hyaluronic acid in knee synovial fluid from carrageenin-induced rabbit arthritis

The concentration and degradation of hyaluronic acid in the synovial fluid of carrageenin-induced arthritic joints of rabbits was studied. A 0.5-ml volume of 1% lambda-carrageenin was intra-articularly injected three times into a right knee joint, and saline into a left. After 5 d from the last injection, inflammatory changes were observed in the synovial membrane and synovial fluid, but not in the articular cartilage. In the inflammatory synovial fluid, lipid peroxide content, phosphatase activity and cell counts were significantly increased, but the copper concentration was not changed. Concentration of polymeric hyaluronic acid and total hyaluronic acid were determined by high-performance liquid chromatography using gel-permeation columns. Total hyaluronic acid was appreciably decreased in the inflammatory fluid. The polymeric hyaluronic acid determined was 38% of the total hyaluronic acid in the inflammatory fluid and 74% in the control fluid. This suggests that in the inflammatory fluid, molecular weights of hyaluronic acid are distributed in the broader range. The concentration of chondroitin sulphates was similar in both the inflammatory fluid and the control fluid, but the content ratio of chondroitin sulphates to hyaluronic acid was higher in the inflammatory fluid. In the inflamed synovial membrane, synthesis of hyaluronic acid as measured by incorporation of [14C]glucosamine into glycoconjugates was increased by about twice that in the control membrane.     

Capillary electrophoresis for simultaneous analysis of heparin, chondroitin sulfate and hyaluronic acid and its application in preparations and synovial fluid

A simple and accurate capillary electrophoresis (CE) method was developed to simultaneously separate and quantify heparin, chondroitin sulfate and hyaluronic acid. The relative standard deviations (intra-day) of migration time, peak height and peak area for heparin, chondroitin sulfate and hyaluronic acid were lower than 1.11, 5.45 and 2.82%, respectively. The limits of detection of heparin, chondroitin sulfate and hyaluronic acid were 0.91, 0.12 and 9.04 × 10(-3) mg/mL, respectively. The developed electrophoretic method was successfully applied to the analysis of commercial drug products and biological samples containing chondroitin sulfate and/or hyaluronic acid. The recoveries for chondroitin sulfate and hyaluronic acid were in the range of 95.9 ~107.0%. This was the first time the content of hyaluronic acid in the synovial fluids from osteoarthritic rabbits was investigated by CE. The results suggested that hyaluronic acid in the synovial fluids from osteoarthritic rabbits may be further metabolized and the administration of chondroitin sulfate or hyaluronic acid could affect the content and metabolism of hyaluronic acid in the synovial fluids. The developed CE method was simple to implement without sample pretreatment such as depolymerisation, very repeatable and easily transferred from lab to lab.     

含氟香豆素透明质酸衍生物的合成及其荧光性能

以间氨基苯酚与三氟乙酰乙酸乙酯反应生成4-三氟甲基-7-氨基香豆素,其与氯乙酰氯反应生成-4-三-氟甲基-7-氯乙酰氨基香豆素。 该化合物与透明质酸钠反应得到了含氟香豆素透明质酸衍生物。 利用荧光光谱等分析技术研究了浓度、pH值和温度变化对该透明质酸衍生物荧光强度的影响,同时研究了金属离子对其荧光强度的影响。 结果表明,一定浓度范围内,荧光强度随透明质酸衍生物浓度增大而逐渐增强;在pH值为3.86～8.85范围内,其荧光强度较为稳定;在10～80 ℃范围内,其荧光强度随温度的升高而逐渐减弱;在常见干扰离子存在下,Fe3+对其荧光强度有较为显著的影响,其荧光强度显著降低。 这为探索透明质酸在生命机体内的药物载体机理及其靶向作用提供良好的实验基础。     

Moisture Absorption Effects on the Mechanical Properties of Sandwich Biocomposites with Cork Core and Flax/PLA Face Sheets

The aim of this study was to evaluate the moisture absorption behaviour and its influence on the mechanical properties of newly developed sandwich biocomposites with flax fibre-reinforced poly-lactic acid (PLA) face sheets and soft cork as the core material. Three different types of sandwich biocomposite laminates comprised of different layup configurations, namely, non-woven flax/PLA (Sample A), non-woven flax/PLA and cork as core (Sample B) and non-woven flax/paper backing/PLA, cork as core (Sample C), were fabricated. In order to evaluate the influence of moisture ingress on the mechanical properties, the biocomposites were immersed in seawater for a period of 1200 h. The biocomposites (both dry and water immersed) were then subjected to tensile, flexural and low-velocity falling weight impact tests. It was observed from the experimental results that the moisture uptake significantly influenced the mechanical properties of the biocomposites. The presence of the cork and paper in sample C made it more susceptible to water absorption, reaching a value of 34.33%. The presence of cork in the core also has a considerable effect on the mechanical, as well as energy dissipation, behaviours. The results of sample A exhibited improved mechanical performance in both dry and wet conditions compared to samples B and C. Sample A exhibits 32.6% more tensile strength and 81.4% more flexural strength in dry conditions than that in sample C. The scanning electron microscopy (SEM) and X-ray micro-CT images revealed that the failure modes observed are a combination of matrix cracking, core crushing and face core debonding. The results from this study suggest that flax/PLA sandwich biocomposites can be used in various lightweight applications with improved environmental benefits.     

Biocomposites based on ramie fibers and poly(L‐lactic acid) (PLLA): morphology and properties

We herein report effects of morphology of PLLA and natural fiber on combination properties of biocomposites based on PLLA and ramie fibers. For this purpose, short ramie fiber (FIB), ramie fabric (FAB), PLLA film (FPLLA), and PLLA powder (PPLLA) were used to investigate the structure–property relationship of PLLA biocomposites with 30 wt% ramie fiber prepared by hot compression molding. It is revealed that mechanical properties of biocomposites are strongly dependent on the morphology of PLLA and FAB. DMA test shows that the improved storage modulus was due to the better dispersion of FIB. DSC and POM tests show that PLLA/FIB biocomposites have the highest spherulite growth rate. TGA test shows that char residue at high temperature is affected by the dispersion of PLLA and ramie fiber. SEM images exhibit the different interfacial adhesion character of FIB and FAB in the PLLA matrix after the ramie fiber treated with alkali and silane. PLLA/FAB biocomposites have not only better anti‐dripping properties when burning but also better aging resistance in UV‐irradiation hydrothermal aging, and which can be attributed to fiber bundle and laminated PLLA biocomposites structure. Copyright © 2010 John Wiley & Sons, Ltd.     

Efficient barrier properties of mechanically enhanced agro-extracted cellulosic biocomposites

The objective of this work was to prepare the mechanically stable hydrophobic biocomposites by incorporating the cellulose fibers into the polymer matrices for their applications in biomedical and food packaging. Herein, two different types of biocomposites were prepared by mixing polylactic acid (PLA) and polyhydroxybutyrate (PHB) with the agro-extracted cellulose, separately at 170 °C. The influence of the cellulose fibers on the thermal, mechanical, and barrier properties of polymer matrices (PLA and PHB) was observed. With an increase in the cellulose content in PLA and PHB, the tensile strength of the biocomposite materials significantly improved with the enhancement of 24.45% and 32.08%, respectively, compared with the pure PLA and PHB. Furthermore, a decrease of 74.16% and 73.49% in the water vapor transmission rate and oxygen transmission rate, respectively, was observed for cellulose/PHB biocomposites. This study highlights that adding cellulose fibers significantly improves the mechanical and the barrier properties of PLA and PHB, suggesting their biocomposites for use in biodegradable polymer industries.     

The influence of pre-treatment of Spartium junceum L. fibres on the structure and mechanical properties of PLA biocomposites

Different chemical pre-treatments of Spartium junceum L. fibres using alkali (NaOH), nanoclay (MMT) and Citric acid (CA) with the aim of producing biodegradable composite material are discussed. As environmental requirements in processing technologies have been higher in recent years, the Polylactic acid (PLA) is used in this research as a matrix, due to its renewability, biodegradability and biocompatibility. Biocomposites are prepared by reinforcing PLA with randomly oriented, short Spartium junceum L. fibres in order to increase material strength. The effects of different pre-treatments of Spartium junceum L. fibres on the mechanical properties of final biocomposite material are examined. Fibre tenacity is studied using Vibroscop and Vibrodyn devices. Tensile strength of biocomposite material was measured on the universal electromechanical testing machine Instron 5584. The results indicate that biocomposites reinforced with fibres modified with MMT and CA show upgraded mechanical properties of the final composite material in comparison with the composite materials reinforced with referenced (nontreated) fibres. Infrared spectra of tested fibres and biocomposites were determined with Fourier transform infrared spectroscopy using Attenuated total reflection (FT-IR ATR) sampling technique and the influence of fibre modifications on the fibre/polymer interfacial bonding was investigated. The interface of Spartium/PLA composites was observed with scanning electron microscope (SEM) and it was clearly visible that biocomposites reinforced with fibres modified by MMT and CA showed better interaction of fibres and matrix.     

Thermal characterization and electrical properties of Fe-modified cellulose long fibers and micro crystalline cellulose

Thermal properties of polylactic acid (PLA) filled with Fe-modified cellulose long fibers (CLF) and microcrystalline cellulose (MCC) were studied using thermo gravimetric analysis (TG), differential scanning calorimetry, and dynamic mechanical analysis (DMA). The Fe-modified CLFs and MCCs were compared with unmodified samples to study the effect of modification with Fe on electrical conductivity. Results from TG showed that the degradation temperature was higher for all composites when compared to the pure PLA and that the PLA composites filled with unmodified celluloses resulted in the best thermal stability. No comparable difference was found in glass transition temperature (T _g) and melting temperature (T _m) between pure PLA and Fe-modified and unmodified CLF- and MCC-based PLA biocomposites. DMA results showed that the storage modulus in glassy state was increased for the biocomposites when compared to pure PLA. The results obtained from a femtostat showed that electrical conductivity of Fe-modified CLF and MCC samples were higher than that of unmodified samples, thus indicating that the prepared biocomposites have potential uses where conductive biopolymers are needed. These modified fibers can also be tailored for fiber orientation in a matrix when subjected to a magnetic field.     

Effect of poly (lactic acid)‐graft‐glycidyl methacrylate as a compatibilizer on properties of poly (lactic acid)/banana fiber biocomposites

The main aim of this study was to synthesis of poly (lactic acid) (PLA)‐graft‐glycidyl methacrylate (GMA) as well as its influence on the properties of PLA/banana fiber biocomposites. PLA‐graft‐GMA graft copolymer (GC) was synthesized by melt blending PLA with GMA using benzoyl peroxide and dicumyl peroxide as initiators. Graft copolymerization was confirmed by FTIR and ¹H‐NMR spectroscopic studies. PLA/silane treated banana fiber (SiB) biocomposites with various GC concentrations were prepared by melt blending followed by injection molding techniques. The influence of GC content on the mechanical, thermal and moisture resistance properties of the composite was investigated. The addition of 15 wt% GC content in the biocomposite provided optimum tensile and flexural strength, which is attributed to the greater compatibility between fiber and PLA matrix. The thermal properties of biocomposites have been evaluated using thermogravimetric analysis which provided evidence of improved interfacial adhesion between SiB and PLA by the addition of GC. Additionally, GC enhanced the moisture absorption resistance of biocomposites. These results indicated that GC is indeed a good candidate as a compatibilizing agent to improve the compatibility in PLA/fiber biocomposites. Copyright © 2015 John Wiley & Sons, Ltd.     

软骨素酶ABC酶解高效液相法测定鱼翅中的透明质酸

 建立了一种测定鲨鱼翅中透明质酸的酶解 高效液相方法。在37℃,0 2mol/LTris HCl缓冲溶液中,鱼翅中的透明质酸被硫酸软骨素酶ABC酶解成透明质酸二糖。条件为:ZORBAX糖分析柱(4 6mmi d ×250mm,5μm)柱;紫外检测波长226nm;流动相为乙腈 0 5%磷酸(体积比为2∶98),流速1mL/min;进样量10μL。透明质酸二糖的线性范围为25g/L～600g/L。将此法应用到鱼翅的实际样品检测中,取得了良好的结果,透明质酸在鱼翅样品中的质量分数为0 86%～1 96%。     

Quantitation of hyaluronic acid and chondroitin sulphates in rabbit synovial fluid by high-performance liquid chromatography of oligosaccharides enzymatically derived thereof

A high-performance liquid chromatographic (HPLC) method for quantifying unsaturated hexasaccharide and tetrasaccharide from Streptomyces hyaluronidase enzyme digestion products of hyaluronic acid was developed using a gel-permeation column packed with a sulphated polystyrene-divinylbenzene gel. For the oligosaccharides, the separation was accomplished in less than 7 min with a detection limit of 65 ng. An unsaturated non-sulphated disaccharide prepared from hyaluronic acid (delta Di-HA) and an unsaturated sulphated disaccharide (delta Di-4S) were analyzed by a HPLC method using a combination of two different gel-permeation columns. The separation of the disaccharides required less than 17 min at a flow rate of 0.7 ml/min with detection limits of as little as 4 ng for delta Di-HA and 5 ng for delta Di-4S. Both chromatographic methods were used for assay of a major component of hyaluronic acid and trace amounts of chondroitin sulphates in rabbit synovial fluid. The resulting contents of hyaluronic acid were compared to the values of polymeric hyaluronic acid directly measured by a HPLC method using two gel-permeation columns packed with a poly(hydroxyalkyl methacrylate) gel and the amounts of hyaluronic acid converted from uronic acid content determined by a colorimetric method.