Poly(imide ether sulphone) as new soluble high performance polymer

Poly(imide ether sulphone) as novel high-performance polymer has been obtained by the condensation polymerization of 4,4'-bis(4-fluorophthalimido) diphenyl ether with 4,4'-sulfonyldiphenol via aromatic nucleophilic substitution reaction. Its structure was confirmed by means of FTIR and NMR spectroscopy, elemental analysis. Differential scanning calorimetry and thermal analysis measurements showed that synthesized polymer possessed high glass transition temperature (T_g = 210°C) and good thermal stability with high decomposition temperatures (T_d > 480°C). Prepared polymer film showed good light transmittance and mechanical strength.     

Synthesis and properties of novel heat-resistant fluorescent conjugated polymers with bisindolylmaleimide

Novel conjugated polymers with bisindolymaleimide were synthesized via simple metal-free condensation polymerization. The polymers exhibited high glass transition temperatures and decomposition temperatures with considerable luminescent properties.     

Co oxidation with oxygen in the presence of hydrogen on CoO/CeO<Subscript>2</Subscript> and CuO/CoO/CeO<Subscript>2</Subscript> catalysts

The catalytic activity of the CoO/CeO₂ and CuO/CoO/CeO₂ systems in selective CO oxidation in the presence of hydrogen at 20–450°C ([CuO] = 1.0–2.5%, [CoO] = 1.0–7.0%) is reported. The maximum CO conversion (X) decreases in the following order: CuO/CoO/CeO₂ (X = 98–99%, T = 140–170°C) > CoO/CeO₂ (X = 67–84%, T = 230–240°C) > CeO₂ (X = 34%, T = 350°C). TPD, TPR, and EPR experiments have demonstrated that the high activity of CuO/CoO/CeO₂ is due to the strong interaction of the supported copper and cobalt oxides with cerium dioxide, which yields Cu-Co-Ce-O clusters on the surface. The carbonyl group in the complexes Co^δ+-CO and Cu⁺-CO is oxidized by oxygen of the Cu-Co-Ce-O clusters at 140–160°C and by oxygen of the Co-Ce-O clusters at 240°C. The decrease in the activity of the catalysts at high temperatures is due to the fact that hydrogen reduces the clusters on which CO oxidation takes place, yielding Co⁰ and Cu⁰ particles, which are inactive in CO oxidation. The hydrogenation of CO into methane at high temperatures is due to the appearance of Co⁰ particles in the catalysts.     

Synthesis and properties of novel soluble poly(aryl amine ketone)s as high-performance polymers

A series of poly(aryl amine ketone)s have been obtained by the condensation polymerization of different aromatic dibromides with different primary aromatic diamines via palladium-catalyzed aryl amination reaction. The structures of polymers are characterized by means of FT-IR, 1H NMR spectroscopy, and elemental analysis. The results show an agreement with the proposed structures. DSC and TG measurements show that polymers possess high glass transition temperature (Tg>170℃) and good thermal stability with high decomposition temperatures (TD>450℃). These novel polymers also exhibit good mechanical behaviors and good solubility.     

Novel hyperbranched polymers as host materials for green thermally activated delayed fluorescence OLEDs

A series of novel hyperbranched polymers(HBPs) consisting of a 2,7-subsituted 9-(heptadecan-9-yl)-9H-carbazole unit(A_2+A_2') and a tetra-substituted green thermally activated delayed fluorescence(TADF) dye of 2,3,5,6-tetra(9Hcarbazol-9-yl)-4-pyridinecarbonitrile(4CzCNPy, B4) have been synthesized via Suzuki cross-coupling reaction following an "A2+A2'+B_4" method. The polymers are named according to the polymerization ratio of 4CzCNPy monomer(5 mol%, 10 mol% and 15 mol% for HBPs of P2-P4 respectively, and 0 mol% for the control linear polymer P1). Their thermal, optoelectronic and electrochemical properties have been characterized by a combination of techniques. All the polymers exhibit high thermal stability with the decomposition temperatures(Td) above 400 ℃ and glass transition temperatures(Tg) up to 98 ℃. Unfortunately, the incorporation of TADF moiety into these HBP materials induced non-TADF characteristics. However, when the HBPs functionalized as the host for our previously developed 4CzCNPy TADF dopant in solution processed devices, maximum external quantum efficiency of 5.7% and current efficiency of 17.9 cd/A have been achieved in P3-based device, which is significantly higher than those of 1.5% and 4.2 cd/A for the linear polymer P1.     

Study of Kryptofix5 Complexation with La<Superscript>3+</Superscript> Cation in Several Individual and Binary Nonaqueous Solvents Using Conductometric Method

Complexatio of the La³⁺ cation with 1,13-bis(8-quinolyl)-1,4,7,10,13-pentaoxatridecane(Kryptofix5) was studied in pure solvents acetonitrile (AN), methanol (MeOH), nitrobenzene (NB), tetrahydrofuran (THF), methyl acetate (MeOAC) and in various binary solvent mixtures of AN–MeOH, AN–NB, AN–THF, and AN–MeOAC systems at different temperatures using the conductometric method. The stoichiometry of the complex was found to be 1 : 1 (ML). In all cases, the variation of the log kf with composition of the solvent was non-linear. This behavior is probably due to a change in the structure of these binary mixed solvents as the composition of the medium is varied. The stability order of the complex in pure nonaqueous solvents at 25°C increases in the order: AN > THF > MeOAC > MeOH > NB. The values of thermodynamic data (ΔH _c °,ΔS _c °) formation of (Kryptofix5.La)³⁺ complex are definitely solvent dependent.     

High-pressure defect phase La<Subscript>x</Subscript>Cu<Subscript>3</Subscript>V<Subscript>4</Subscript>O<Subscript>12</Subscript>

Perovskite-like nonstoichiometric oxide La _x Cu₃V₄O₁₂ (space group Im \(\bar 3\), Z = 2, a = 7.313–7.354 Å) with cation-site vacancies has been prepared for the first time at high pressures (p = 6.0–8.0 GPa) and high temperatures (T = 700–1100°C). The compound has metal-type conductivity and paramagnetic properties, and undergoes a phase transition.     

Facile synthesis of soluble aromatic poly(amide amine)s via C–N coupling reaction: Characterization,thermal, and optical properties

Aromatic poly(amide amine)s (APAAs), as novel high‐performance polymers, have been obtained by the condensation polymerization of N,N'‐bis(4‐bromobenzoyl)‐p‐phenylenediamine with two different primary aromatic diamines via palladium‐catalyzed aryl amination reaction. The structures of the polymers are characterized by means of FTIR, ¹H NMR spectroscopy, and elemental analysis, the results show a good agreement with the proposed structures. DSC and TGA measurements exhibit that polymers possess high glass transition temperature (T_g > 240 °C) and good thermal stability with high decomposition temperatures (T₅ > 400 °C). These novel polymers also display good solubility. In addition, due to its special structure, APAA‐2 is endowed with significantly strong photonic luminescence in N,N‐dimethylformamide and good electroactivity. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013 , 51, 4845–4852     

High thermal stable polyimide resins derived from phenylethynyl-endcapped fluorenyl oligoimides with low melt viscosities

To improve the processability and thermal stability of polyimide, a series of novel phenylethynyl-endcapped oligoimides(PEPA-oligoimides) with calculated molecular weights(M_nC) were successfully prepared from thermal imidization of 4,4'-(9-fluorenylidene) dianiline(BAFL) as fluorenyl diamine, 4,4′-oxy-diphthalic anhydride(ODPA) as aromatic dianhydride and 4-phenylethynylphthalic anhydride(4-PEPA) acted as reactive end-capping reagent at elevated temperatures. Experiment results indicated that the oligoimides were the mixtures of PEPA-endcapped oligomers with different degrees of polymerization characterized by MALDI-TOF mass spectra. The influence of chemical structures on the melt processabilities of the oligoimides, the thermal, dielectric and mechanical properties of the thermoset resins was studied. The typical oligoimide resin owned minimum melt viscosity of 0.2 Pa·s at around 310 °C and wide melting processing window, suitable for resin transfer molding(RTM). Besides, its corresponding thermal-cured polyimide resin possessed glass transition temperature(T_g) as high as 514 °C. The dielectric constants of polyimide resins decreased from 3.15 to 2.80 by reducing the M_nC. The mechanical properties of the polyimide neat resins were improved gradually with increasing MnC. Finally, the carbon fiber/polyimide(C_f/PI) composite laminates showed excellent mechanical strength retention rate at 350 °C, might be long-term served at extremely high temperature in aerospace and aviation field.     

Neutron diffraction study of dehydrogenation of titanium carbohydrides TiC<Subscript><Emphasis Type="Italic">x</Emphasis></Subscript>H<Subscript><Emphasis Type="Italic">y</Emphasis></Subscript>

The possibility of the synthesis of hydrogen-nonstoichiometric cubic titanium carbide ТiС _х of high purity from powdery nonstoichiometric cubic titanium carbohydride ТiС _х H _y or nonstoichiometric titanium carbide with admixture hydrogen by annealing in a continuously maintained vacuum of no worse than 1.33 × 10^–3 Pa at temperatures of 600–750°C for several hours has been shown. Similar annealing at higher temperatures (T ≥ 800°C) does not lead to the complete removal of hydrogen from a sample due to intensive sintering. In this case, it seems that pores between sintered particles are hydrogen traps, and the release of hydrogen through the surface of sintered particles is hindered.     

Dynamic mechanical relaxation effects in some poly(arylene sulfones)

Poly-4,4′-oxydiphenylenesulfonyl and poly-4,4′-methylenediphenylenesulfonyl were synthesized by an electrophilic substitution polymerization of the arylene monosulfonyl chloride monomers. The glass-transition temperatures T_g of these polymers were determined by calorimetric and dynamic mechanical measurements, and the number-average molecular weights were determined by vapor-pressure osmometry. Both polymers were found to have the same T_g at equivalent molecular weight; the limiting value at high molecular weight is 238°C. Both polymers have two dynamic mechanical relaxation peaks at temperatures far below T_g. One is in the neighborhood of 0°C, and the other is at ?110°C. Plausible origins for these relaxations, and the absence of any near 0°C in poly(4,4′-isopropylidenediphenylene-co-4,4′-sulfonyldiphenylene dioxide), are discussed.     

Polyurethanes containing sulfur. I. New thermoplastic polyurethanes with benzophenone unit in their structure

New thermoplastic nonsegmented thiopolyurethanes were obtained from the low-melting aliphatic–aromatic thiodiols 4,4′-bis(2-hydroxyethylthiomethyl)benzophenone (BHEB), 4,4′-bis(3-hydroxypropylthiomethyl)benzophenone (BHPB), and 4,4′-bis(6-hydroxyhexylthiomethyl)benzenophenone(BHHB) as well as hexamethylene diisocyanate (HDI), both by melt and solution polymerization with dibutyltin dilaurate as the catalyst. The effect of various solvents on molecular-weight values was examined. The polymers with the highest reduced viscosities (0.63–0.88 dL/g) were obtained when the polymerization was carried out in a solution of tetrachloroethane, N,N-dimethylacetamide, and N,N-dimethylacetamide or N,N-dimethylformamide for BHEB-, BHPB-, and BHHB-derived polyurethanes, respectively. These polymers with a partially crystalline structure showed glass-transition temperatures (T_g) in the range of −1 to 39 °C, melting temperatures (T_m) in the range of 107 to 124 °C, and thermal stabilities up to 230 to 240 °C. The BHEB-derived polyurethane is a low-elasticity material with high tensile strength (ca. 50 MPa), whereas the BHPB- and BHHB-derived polyurethanes are more elastic, showing yield stress at approximately 16 MPa. We also obtained segmented polyurethanes by using BHHB, HDI, and 20 to 80 mol % poly(oxytetramethylene) glycol (PTMG) of M̄_n = 1000 as the soft segment. These are high-molecular thermoplastic elastomers that show a partially crystalline structure. Thermal properties were investigated by thermogravimetric analysis and differential scanning calorimetry. The increase in PTMG content decreases the definite T_g and increases the solubility of the polymers. These segmented polyurethanes exhibit the definite T_g (−67 to −62 °C) nearly independent of the hard-segment content up to approximately 50 wt %, indicating the existence of mainly phase-separated soft and hard segments. Shore A/D hardness and tensile properties were also determined. As the PTMG content increases, the hardness, modulus of elasticity, and tensile strength decrease, whereas elongation at break increases. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 4140–4150, 1999     

Facile Synthesis of Processable Semi-aromatic Polyamide Containing Thioether Units

A series of processable semi-aromatic polyamides containing thioether units have been developed. They were synthesized through the reaction of 4,4’-bis(4-chloroformylphenylthio)benzene (BPB-DC) and aliphatic diamine by the method of interfacial polycondensation. These polyamides had excellent thermal properties with glass transition temperatures (T_g) of 124–137.9°C, melting temperatures (T_m) of 306.4–324.1°C and initial degradation temperatures (T_d) of 409.5–437°C. They had wider processing windows than traditional semi-aromatic polyamides and can be processed by the melting method. They had better tensile strengths of 61.2–73.7 MPa, low-temperature mechanical properties, low water absorption of 0.17%–0.23%, low dielectric constants of 3.47–3.66 at 100 kHz and better melt flowability properties of 37.3 to 164.4 Pa. s, 48.2 to 281.7 Pa. s and 58.3 to 486.7 Pa. s at different shear rates, respectively. Additionally, these polyamides showed good corrosion resistance, they did not dissolve in solvents such as NMP, DMSO, hydrochloric acid (6 mol/L), H₃PO₄ and solution of NaOH (1 mol/L) etc.     

Facile synthesis of heat‐resistant and photoluminescent poly(N‐aryleneindole ether)s via catalyst‐free C?N/C?O coupling reaction

We present here a novel programmable polymerization route for the synthesis of new indole‐based polymers via a catalyst‐free nucleophilic substitution reaction. The polycondensation of 4‐hydroxyindole with different activated difluoro monomers undergoes in N‐methylpyrrolidinone, affording soluble poly(N‐aryleneindole ether)s (PEINs) with high molecular weights (M_w up to 486,000) in high yields (up to 96%). The structures of the polymers are characterized by means of FT‐IR, ¹H NMR spectroscopy and elemental analysis, the results show good agreement with the proposed structures. The resulting polymers are processable and enjoy high glass transition temperatures (T_gs > 180 °C) and thermal stability (T_ds > 420 °C). Thin films of PEINs show great mechanical behaviors with high tensile strength up to 104 Mpa, and good optical transparency. In addition, due to the indole moieties in the main chains, all these PEINs are endowed with significantly strong photonic luminescence in chloroform and display highly solvent‐dependent emission bands. Especially, the polymer PEIN‐3 carrying sulfonyl units, shows outstanding blue‐light emission with high quantum yields (45.2%, determined against quinine sulfate). The results obtained by cyclic voltammetry suggest that PEINs possess good electroactivity. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 313–320     

Layer structures. VI. Chiral sanidic polyesters derived from 2,5-bis (dodecyloxy) terephthalic acids and 4,4′-dihydroxybiphenyl

Copolycondensations of (S,S)-2,5-bis(2-methylbutyloxy) terephthaloylchloride with 2,5-bis(dodecyloxy)terephthaloylchloride and with 4,4′-bistrimethylsiloxybiphenyl yielded a series of novel chiral thermotropic copolyesters. These polyesters were characterized by elemental analyses, inherent viscosities, ¹H-NMR spectroscopy, optical rotations, optical microscopy, DSC measurements, and WAXS powder patterns recorded with synchrotron radiation under variation of the temperature. All homo- and copolyesters formed a solid sanidic layer structure with melting temperatures (T_m) ≥ 200°C. A broad enantiotropic nematic or cholesteric phase is formed above T_m with isotropization temperatures (T_is) in the range of 275–325°C. Yet, the T_m of the chiral homopolyester is so high (378°C) that the melting process is immediately followed by rapid degradation. The cholesteric phases of the copolyesters displayed unusual mobile schlieren textures, but a stable Grandjean texture was never obtained. Cholesteric domains consisting of loose bundles of more or less helical main chains are discussed as supramolecular order responsible for the observed textures and their pronounced temperature dependence. © 1997 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 35: 947–957, 1997     

High Performance Poly(ether-amide)s Derived from 1,1-Bis[4-(4-carboxy methylene phenoxy)-3-methyl phenyl] Cyclopentane and Aromatic Diamines

A series of new methyl substituted poly(ether-amide)s were synthesized by using direct Yamazaki’s phosphorylative polycondensation of novel diacid 1,1-bis[4-(4-carboxymethyl phenoxy)-3-methylphenyl] cyclopentane (BCMMP) with various aromatic diamines. These polymers were characterized by FTIR spectroscopy. Inherent viscosities of these polymers were in the range 0.25 to 0.42 dL/g indicating moderate molecular weight built-up. These polymers exhibited excellent solubility in various polar aprotic solvents such as NMP, DMSO, DMAc, DMF, pyridine, and were insoluble in THF, DCM and chloroform. X-Ray diffraction pattern of polymers showed that incorporation of methyl substituent on aromatic backbone and cardo cyclopentylidene moiety containing ether linkage and methylene spacer would disturb the chain regularity and packing, leading to amorphous nature. Thermal analysis by TGA showed excellent thermal stability of polymers. The glass transition temperature T_g were in the range 195–210°C. The structure-property correlation among this poly(ether-amide)s was studied, in view of these polymer’s potential applications as high performance polymers.     

Copolymerization of fluorene‐based main‐chain benzoxazine and their high performance thermosets

A series of fluorene‐based benzoxazine copolymers were synthesized from the mixture of 9,9‐bis(4‐hydroxyphenyl)fluorene and bisphenol A, and 4,4′‐diaminodiphenyloxide and paraformaldehyde. And the cured polybenzoxazine films derived from these copolymers were also obtained. Fourier transform infrared spectroscopy (FTIR) and hydrogen nuclear magnetic resonances confirmed the structure of these benzoxazines. Their molecular weight was estimated by gel permeation chromatography. The curing behavior of the precursors was monitored by FTIR and differential scanning calorimetry. Dynamic mechanical analysis and thermogravimetric analysis were performed to study the thermal properties of the cured polymers. The cured polybenzoxazines exhibit excellent heat resistance with glass transition temperatures (T_g) of 286–317°C, good thermal stability along with the values of 5% weight loss temperatures (T₅) over 340°C, and high char yield over 50% at 800°C. The mechanical properties of the cured polymers were also measured by bending tests. Copyright © 2015 John Wiley & Sons, Ltd.     

Highly refractive polymer resin derived from sulfur‐containing aromatic acrylate

New sulfur‐containing polymers with high‐refractive indices and low birefringences have been developed as UV‐curable high‐refractive polymer resins. The polymers derived from 2,7‐bis[(2‐acryloylethyl)sulfanyl]thianthrene (2,7‐BAST) and 4,4′‐bis[(acryloyloxyethylthio)diphenylsulfide (4,4′‐BADS) were prepared by photopolymerization under UV irradiation. Transparent UV‐cured films were obtained in both cases. Both polymers showed good thermal stability, such as a 5% weight‐loss temperature at 355 °C under nitrogen and glass transition temperatures (T_g) in the range of 94–143 °C. They also showed high‐refractive indices of 1.6531 and 1.6645 at 632.8 nm and low birefringences of 0.0039 and 0.0069 in addition to high transparency in the visible region. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 2604–2609, 2010     

Non-Isothermal Crystallization Behavior of β-Nucleated Isotactic Polypropylene/Multi-Walled Carbon Nanotube Composites with Different Melt Structures

In this study, the melt structure status of isotactic polypropylene/multi-walled carbon nanotubes composites (iPP/MWCNTs) nucleated with β-NA was tuned by changing the fusion temperature T _f . The non-isothermal crystallization behavior and subsequent melting behavior of the sample were studied in detail. The results showed that under different cooling rates (2, 5, 10, 20 and 40 deg/min), the crystallization temperature increased gradually with the decrease of T _f , meanwhile, when T _f was in the temperature range of 166–174°C where ordered structures survived in the melt (named Region II), the crystallization activation energy was significantly lower compared with the case T _f > 174°C or T _f < 166°C. On the subsequent melting curves, the occurrence of the melt structure can be observed at all the cooling rates studied; the location of the Region II was constant, which did not show dependency on the cooling rates; low cooling rate and relative low T _f within 166–174°C encouraged the formation of more β-phase triggered by melt structure.     

Catalytic removal of soot particles over MnCo<Subscript>2</Subscript>O<Subscript>4</Subscript> catalysts prepared by the auto-combustion method

Soot removal for exhaust gas from diesel engine has been addressed due to the more stringent legislation and environmental concerns. MnCo₂O₄ catalysts were systematically prepared using glucose as a fuel via the auto-combustion method and applied for soot removal. The as-prepared samples were characterized by X-ray diffraction (XRD), O₂-temperature-programmed oxidation (TPO) reaction and H₂-temperature-programmed reduction reaction (H₂-TPR). The catalytic activities for soot combustion were evaluated by micro activity test (MAT) with a tight contact mode between soot and catalysts. Compared with catalysts prepared by the solid state method without glucose, auto-combustion method in the presence of glucose can decrease the synthetic temperature, avoiding high temperature treatment and sintering. The catalysts prepared with glucose could catalyze soot oxidation effectively and the derived values of T₁₀, T₅₀, and T₉₀ were 326, 408, and 468 °C in a tight contact mode, respectively, showing a significant drop of T₁₀, T₅₀, and T₉₀ by 156, 177, and 178 °C for non-catalytic reaction.