Hydrothermal synthesis, crystal structure and characterization of [Zn(H2O)4]2 [H2As6V15O42(H2O)]·2H2O

The compound [Zn(H₂O)₄]₂[H₂As₆V₁₅O₄₂(H₂O)]·2H₂O (1) has been synthesized and characterized by elemental analysis, IR, ESR, magnetic measurement, third-order nonlinear property study and single crystal X-ray diffraction analysis. The compound 1 crystallizes in trigonal space group R3, a=b=12.0601(17) Å, c=33.970(7) Å, γ=120°, V=4278.8(12) Å³, Z=3 and R1(wR2)=0.0512 (0.1171). The crystal structure is constructed from [H₂As₆V₁₅O₄₂(H₂O)]⁴⁻ anions and [Zn(H₂O)₄]²⁺ cations linked through hydrogen bonds into a network. The [H₂As₆V₁₅O₄₂(H₂O)]⁶⁻ cluster consists of 15 VO₅ square pyramids linked by three As₂O₅ handle-like units.     

Factors influencing decomposition of H2O2 over supported Pd catalyst in aqueous medium

Since H₂O₂ decomposition can result in selectivity/yield loss in the direct H₂O₂ synthesis process from H₂ and O₂ over supported Pd catalysts, it is important to have an enhanced understanding about the factors affecting the H₂O₂ decomposition reaction. Herein, detailed studies have been undertaken to investigate the influence of different factors, such as (a) nature and concentration of acid in reaction medium, (b) nature and concentration of halide in presence and absence of acid in reaction medium, (c) pretreatment procedures and (d) catalyst modification by incorporation of different halides, on the H₂O₂ decomposition reaction over a 5% Pd/C catalyst in aqueous medium at 25 °C. This study has shown that the H₂O₂ decomposition activity is profoundly influenced by all the above factors. The effectiveness of the acids in suppressing the H₂O₂ decomposition activity decreased in the following order: hydroiodic acid > hydrobromic acid > hydrochloric acid  acetic acid > phosphoric acid > sulfuric acid > perchloric acid. The ability of the acid to decrease the H₂O₂ decomposition activity was found to very strongly depend on the nature of its associated anion. Halides, such as iodide, bromide and chloride were particularly effective in suppressing the H₂O₂ decomposition activity. Oxidation pretreatment of the catalyst was found to strongly suppress its H₂O₂ decomposition activity, while a reduction treatment was found to promote its activity. A gradual decrease in the H₂O₂ decomposition activity of the catalyst was observed with each successive usage due to in situ sub-surface oxidation of Pd by H₂O₂. Halide incorporation either via the reaction medium or prior catalyst modification had a similar qualitative effect on the H₂O₂ decomposition activity.     

V_2O_5/Ti-Ce-PILC在H_2S选择性催化氧化过程中的催化性能

合成了TiO_2-CeO_2柱撑黏土负载V_2O_5催化剂,通过XRD、氮气吸附脱附、TG、FT-IR、H_2-TPR、NH_3-TPD、XPS等方法对其物理化学性质进行了表征,研究了该催化剂在H2S选择性催化氧化反应中的活性。结果表明,负载5%V_2O_5的TiO_2-CeO_2柱撑黏土在180℃下催化效果最好,且尾气中不含SO_2。V_2O_5、TiO_2和CeO_2之间的相互作用提高了催化剂的活性,CeO_2提高了催化剂的热稳定性,同时提供大量晶格氧,加强了V_2O_5的氧化还原作用,降低了反应温度;TiO_2加强了VO_x和CeO_x的再氧化,降低了硫酸盐的覆盖率,从而降低了催化剂的失活速率。     

光催化氧气还原制备H2O2

H2O2广泛应用于化工和环保领域,其分解的唯一产物是水,有利于生产与自然生态系统的协调可持续发展.工业上H2O2的合成主要是通过蒽醌法间接合成,该方法能耗大,污染环境.而直接由H2与O2混合制备H2O2,具有极大的安全风险,且需要消耗大量H2.通过光催化技术将O2和H2O转化成H2O2的方法,避免了H2与O2的直接混合...     

Pt/DNA-MWCNTs/GC电极制备及其H2O2还原的电催化活性

将DNA功能化多壁碳纳米管（MWCNTs）复合材料修饰于玻碳基底（GC）表面制得DNA-MWCNTs/GC电极,并在此基础上电沉积负载Pt纳米颗粒构建了一种新型无酶H₂O₂传感电极. 利用扫描电子显微镜（SEM）表征制得的修饰电极,同时通过循环伏安法和计时电流法研究了该传感电极的H2O2响应性能. 结果表明,该传感电极的H₂O₂检测在0.04 ~ 18.07 mmol·L^-1浓度范围内成线性相关,检出限3.85 μmol·L^-1（S/N = 3）,且有良好的重现性、稳定性与选择性.     

H2O2-responsive theranostic nanomedicine

This review summarizes and discusses the very-recent developments of H₂O₂-responsive theranostic nanoplatforms for versatile biomedical applications, including diagnostic imaging, attenuating tumor hypoxia, enhancing the therapeutic effi ciency of photodynamic therapy/radiation therapy/chemotherapy and theranostic of inflammation/diabetic. It is highly believed that H₂O₂-responsive theranostic nanomedicine will be extensively developed a new specifi c and effi cient theranostic modality to benefi t the personalized biomedicine in the near future.     

Fe2O3/Al2O3氧载体用于甲烷化学链燃烧：负载量与制备方法的影响

以不同方法制备了系列Fe₂O₃/Al₂O₃氧载体,采用XRD、H₂-TPR、CH₄-TPR、O₂-TPD和BET等分析技术对氧载体进行了表征。研究了不同Fe₂O₃负载量氧载体的甲烷化学链燃烧性能,考察了不同制备方法对Fe₂O₃/Al₂O₃氧载体结构、反应性和产物选择性的影响。结果表明,Fe₂O₃负载量对氧载体活性及产物中CO₂选择性的影响较大,负载量较低时氧载体活性较低且引起甲烷部分氧化产物CO含量增加。制备方法亦对氧载体与甲烷的反应活性有所影响,整体上共沉淀法制备的质量分数60％Fe₂O₃/Al₂O₃氧载体具有较高的氧化活性和化学链循环稳定性。其在反应温度850℃、反应时间15 min、30次循环后甲烷转化率及产物中CO₂选择性均未见明显降低。     

MOF derived Co3O4/N-doped carbon nanotubes hybrids as efficient catalysts for sensitive detection of H2O2 and glucose

Developing enzyme-free sensors with high sensitivity and selectivity for H2O2 and glucose is highly desirable for biological science.Especially,it is attractive to exploit noble-metal-free nanomaterials with large surface area and good conductivity as highly active and selective catalysts for molecular detection in enzyme-free sensors.Herein,we successfully fabricate hollow frameworks of Co3O4/N-doped carbon nanotubes(Co3O4/NCNTs)hybrids by the pyrolysis of metal-organic frameworks followed by calcination in the air.The as-prepared novel hollow Co3O4/NCNTs hybrids exhibit excellent electrochemical performance for H2O2 reduction in neutral solutions and glucose oxidation in alkaline solutions.As sensor electrode,the Co3O4/NCNTs show excellent non-enzymatic sensing ability towards H2O2 response with a sensitivity of 87.40μA(mmol/L)^-1 cm^-2,a linear range of 5.00μmol/L-11.00 mmol/L,and a detection limitation of 1μmol/L in H2O2 detection,and a good glucose detection performance with 5μmol/L.These excellent electrochemical performances endow the hollow Co3O4/NCNTs as promising alternative to enzymes in the biological applications.     

原位合成H2O2在水处理技术中的应用研究进展

从过氧化氢(H₂O₂)的原位生成技术角度总结了近年来利用原位合成H₂O₂处理水中污染物的研究,分析了当前可充当氢源材料的种类及不同的氢源材料对于提高H₂O₂产率的影响,以及不同的催化剂材料和催化反应环境提高H₂O₂利用率对污染处理效果的影响因素,并对原位合成H₂O₂在水处理领域中面临的挑战和发展前景做了展望,从而为该技术的大规模应用提供指导和借鉴。     

Protein nanoparticles containing Cu(II) and DOX for efficient chemodynamic therapy via self-generation of H2O2

Chemodynamic therapy (CDT) refers to generating hydroxyl radical (^·OH) in tumor sites via hydrogen peroxide (H₂O₂) catalyzed by transition metal ions in cancer cells under acidic environment. However, H₂O₂ content is not enough for effective CDT, although H₂O₂ content in cancer cells is higher than that of normal cells. Herein, we synthesized DOX@BSA-Cu NPs (nanoparticles) for effective CDT by providing enhanced content of H₂O₂ in cancer cells. The results proved Cu²⁺ in NPs could be reduced to Cu⁺ by glutathione (GSH) and effectively converted H₂O₂ to ^·OH. Moreover, the loaded low-dose doxorubicin (DOX) in the NPs could improve the content of H₂O₂ and resulted in more efficient generation of ^·OH in cancer cells. Thus DOX@BSA-Cu NPs exhibited higher cytotoxicity to cancer cells. This research may provide new ideas for the further studies on more effective Cu(II)-based CDT nanoagents.     

超临界水热极速合成异质结构H4SiW12O40/Bi2WO6光催化剂及其脱氮性能

采用超临界水热合成方式极速合成一种H_4SiW_(12)O_(40)/Bi_2WO_6光催化剂,通过X射线衍射(XRD)、场发射扫描电子显微镜(SEM)、透射电子显微镜(TEM)、比表面积及孔隙度(BET)测定对所合成催化剂的结构和性质进行了考察,并以吡啶含量为15 mg/g的模拟油对光催化剂的脱氮效果进行评价。结果表明,该光催化剂为二维纳米片自组装成的三维球状结构,其中,H_4SiW_(12)O_(40)与Bi_2WO_6不是简单的固载关系而是在超临界水热条件下生成一种新的晶相,正是由于这种晶相的存在,使得H_4SiW_(12)O_(40)牢固固载在Bi_2WO_6光催化剂本体上的同时,对光生载流子进行了有效疏导,提升了H_4SiW_(12)O_(40)/Bi_2WO_6光催化剂的使用寿命和光催化活性。本研究针对光催化剂制备周期与晶形发育的矛盾,将超临界水热技术与光催化剂模板导向合成技术有机结合,在获得良好晶形异质结构H_4SiW_(12)O_(40)/Bi_2WO_6光催化剂的同时明显缩短了光催化剂的制备周期,从而降低了催化剂的制备成本,攻克了光催化剂工业化应用的主要矛盾,所制备的H_4SiW_(12)O_(40)/Bi_2WO_6光催化剂轻质油脱氮效率达97%以上。     

化学链制氢中Fe2O3/LaFeO3载氧体的性能研究

采用柠檬酸络合法制备Fe₂O₃/LaFeO₃复合氧化物,将该氧化物作为化学链制氢过程的载氧体,在反应温度为900 ℃、常压下,对Fe₂O₃/CH₄（剂烷比）、进水量、金属负载量进行了考察。结果表明,剂烷比为2：1、进水量为0.1 mL、质量分数15%Fe时载氧体性能最好,甲烷转化率达到60%,单次循环氢气产量为45 mL。将该评价结果与XRD和H₂-TPR表征结果进行关联发现,反应过程的活性位不是金属氧化物,而是吸附氧,而且吸附氧越容易还原,甲烷转化率和氢气产量越高。通过连续60次还原-氧化循环发现,该载氧体上甲烷转化率和氢气产量比较稳定,循环后仍然保持钙钛矿结构。     

离子液体/H_2O_2体系脱硫实验研究

选取四种不同种类离子液体(ILs),1-丁基-3-甲基咪唑溴化物([Bmim]Br)、1-丁基-3-甲基咪唑四氟硼酸盐([Bmim]BF_4)、1-丁基-3-甲基咪唑硫酸氢盐([Bmim]HSO_4)、1-丁基-3-甲基咪唑磷酸二氢盐([Bmim]H_2PO_4)与30%H_2O_2溶液在温和条件下对两种高硫脱灰煤样(LS、QX)进行脱硫实验研究。用化学法测定脱硫前后煤样形态硫含量,并利用傅里叶变换红外光谱(FT-IR)、X射线光电子能谱(XPS)、扫描电子显微镜(SEM)及热重(TG)对脱硫前后的煤样进行表征。结果表明,离子液体的加入使H_2O_2氧化脱硫能力增强,煤中硫铁矿硫和有机硫化物硫被显著脱除;经ILs/H_2O_2体系作用后的煤样中小粒径的颗粒减少,颗粒间的缝隙增大,煤表面的凹坑明显,热重实验结果表明,ILs/H_2O_2体系作用后的煤样相对于原煤热失重增大,部分挥发性物质释放峰温提前。     

Catalytic decomposition of H2O2 on Co3O4 doped with MgO and V2O5

The effects of doping of Co₃O₄with MgO (0.4–6 mol%) and V₂O₅ (0.20–0.75 mol%) on its surface and catalytic properties were investigated using nitrogen adsorption at −196°C and decomposition of H₂O₂ at 30–50°C. Pure and doped samples were prepared by thermal decomposition in air at 500–900°C, of pure basic cobalt carbonate and basic carbonate treated with different proportions of magnesium nitrate and ammonium vanadate. The results revealed that, V₂O₅ doping followed by precalcination at 500–900°C did not much modify the specific surface area of the treated Co₃O₄ solid. Treatment of Co₃O₄ with MgO at 500–900°C resulted in a significant increase in the specific surface area of cobaltic oxide. The catalytic activity in H₂O₂ decomposition, of Co₃O₄ was found to suffer a considerable increase by treatment with MgO. The maximum increase in the catalytic reaction rate constant (k) measured at 40°C on Co₃O₄ due to doping with 3 mol% MgO attained 218, 590 and 275% for the catalysts precalcined at 500, 700 and 900°C, respectively. V₂O₅-doping of Co₃O₄ brought about a significant progressive decrease in its catalytic activity. The maximum decrease in the reaction rate constant measured at 40°C over the 0.75 mol% V₂O₅-doped Co₃O₄ solid attained 68 and 93% for the catalyst samples precalcined at 500 and 900°C, respectively. The doping process did not modify the activation energy of the catalyzed reaction but much modified the concentration of catalytically active constituents without changing their energetic nature. MgO-doping increased the concentration of CO³⁺–CO²⁺ ion pairs and created Mg²⁺–CO³⁺ ion pairs increasing thus the number of active constituents involved in the catalytic decomposition of H₂O₂. V₂O₅-doping exerted an opposite effect via decreasing the number of CO³⁺–CO²⁺ ion pairs besides the possible formation of cobalt vanadate.     

新型Brnsted-Lewis酸性催化剂LaPW_(12)O_(40)/SiO_2制备及其在催化酯化反应合成生物柴油中的应用

以十二磷钨杂多酸(Tungstophosphoric acid,H_3PW_(12)O_(40))为基体,分别通过普通浸渍法、溶胶凝胶法和超声浸渍法进行了La3+改性作用,合成了三种固体酸催化剂A-LaPW_(12)O_(40)、B-LaPW_(12)O_(40)/Si O2和C-LaPW_(12)O_(40)。采用X射线荧光光谱(XRF)、孔径比表面积测定、X射线粉末衍射(XRD)、透射电镜(TEM)、红外光谱(FT-IR)、热重(TG)、N2吸附-脱附、NH3程序升温脱附(NH3-TPD)、吡啶吸附红外光谱(Py-FTIR)、X射线光电子能谱(XPS)等方法对合成的催化剂进行了表征,并比较了以上催化剂在用于催化以油酸和甲醇为反应物经酯化反应合成生物柴油时的活性和稳定性。结果表明,B-LaPW_(12)O_(40)/Si O2具有最高催化活性,当甲醇与油酸的物质的量比为8∶1,催化剂用量为反应物总质量的2%,反应温度为65℃,反应1 h后,油酸的转化率即高达93%。循环使用B-LaPW_(12)O_(40)/Si O2催化剂六次后,油酸的转化率仍高达86.4%。B-LaPW_(12)O_(40)/Si O2的高催化活性和稳定性可归因于在溶胶凝胶的转化过程中,作为硅源材料的四乙氧基硅(TEOS)易在酸性条件下发生水解反应形成Si O2网络,进而Si O2网络中的硅醇键与H_3PW_(12)O_(40)中的H+发生配位作用,生成具有强静电吸附力的(≡Si-OH2+)(H2PW12O-40)络合物。随着该络合物的形成,促进了La3+在Si O2表面的吸附而堵塞了H_3PW_(12)O_(40)的孔道结构,抑制了H_3PW_(12)O_(40)颗粒在焙烧过程中进一步聚集长大。Si O2将作为载体并以干凝胶状态存在于B-LaPW_(12)O_(40)/Si O2催化剂中,由于Si O2凝胶的高比表面积而使B-LaPW_(12)O_(40)/Si O2具有了较大的比表面积,从H_3PW_(12)O_(40)的1.4 m2/g增加至31.3 m2/g。并且,通过吡啶吸附红外光谱确定B-LaPW_(12)O_(40)/Si O2为Br9nsted-Lewis酸型固体酸,由于Br9nsted酸位易与酯化反应过程中生成的水发生水合反应而失活,因而Lewis酸位的形成有助于减少催化剂的失活现象发生。Lewis酸位的出现可归因于(≡Si-OH2+)(H2PW12O-40)与吸附在其表面的具有强吸电子作用的La3+发生键合作用后生成了LaPW_(12)O_(40)/Si O2。     

Mg-Al LDH的制备及Mg-Al LDH/H2O2体系降解水中环丙沙星的研究

分别以MgO和Al(OH)3为镁源及铝源,采用水热法制备Mg-Al LDH,研究了水热温度和氢氧化钠浓度对水热产物纯度的影响。结果显示在NaOH/MgO/Al(OH)3/(Na₂CO₃)摩尔比为2∶1∶0.5∶0.25,水热反应温度在120~150℃,反应12 h,可以得到纯相Mg-Al LDH。进一步以所制备的Mg-Al LDH为吸附剂,H₂O₂为氧化剂。系统研究了Mg-Al LDH/H₂O₂体系溶液pH、H₂O₂用量、污染物浓度、反应温度、反应时间等因素对Mg-Al LDH/H₂O₂体系降解水体中环丙沙星效果的影响。当Mg-Al LDH用量为0.05 g,H₂O₂用量为2 mL,系统pH为6.98,反应温度为35℃,环丙沙星浓度为30 mg·L^-1时,反应13 min环丙沙星的降解率可达97%。随着反应温度的升高,反应速率及平衡时降解率均有所提高,该过程可以用拟一级动力学方程描述,反应的表观活化能E a为19.29 kJ·mol^-1,指前因子A为0.38×10³ min^-1。Mg-Al LDHs/H₂O₂体系降解环丙沙星过程受反应速率控制,而非受传质控制。     

铈修饰铁基复合载氧体用于化学链甲烷部分氧化重整制合成气研究

以Al₂O₃为惰性载体,利用共沉淀法制备了CeO₂-Fe₂O₃-Al₂O₃复合载氧体,并对载氧体进行了XRD、SEM表征。在固定床反应器中,考察了程序升温、恒温、多循环等操作条件下,载氧体对甲烷部分氧化重整的反应性能。程序升温实验结果表明,在相同温度下,CeO₂含量为30%的载氧体与不含CeO₂的载氧体对比,CH₄转化率、H₂和CO选择性均提高。在恒温实验中,含有CeO₂的两种载氧体,CH₄转化率、H₂和CO选择性上也都明显高于不含CeO₂的载氧体,当反应时间小于1 200 s时,无积炭发生。三种载氧体经过15次循环后,CeO₂含量为30%的载氧体表现出最佳的循环特性。多循环实验中,当反应温度850 ℃、反应时间945 s时,CH₄最大转化率达到91.53%、H₂的最大选择性达到86.36%、CO的最大选择性达到85.12%、H₂与CO的最佳平均物质的量比为2.03。XRD谱图显示,经过多次循环后,三种载氧体的物相没有发生变化,载氧体表现出了很好的稳定性能。     

添加Cl离子对V_2O_5-WO_3/TiO_2催化剂低温NO转化率的影响

考察添加不同含量Cl离子对浸渍法制备的Cl-V_2O_5-WO_3/TiO_2催化剂低温NO转化率的影响。随着Cl离子质量添加量从0增加到2.5%,Cl-V_2O_5-WO_3/TiO_2催化剂NO转化率先升高后降低,结合在含有SO_2和H2O的SCR实验结果,确定1.5%Cl-V_2O_5-WO_3/TiO_2为性能最优催化剂。在反应温度为149-362℃,NO转化率大于95%;在145-385℃,NO转化率大于90%。采用XRF、BET、XRD、TG、FT-IR和H2-TPR等方法表征了催化剂的物理化学性能和结构。结果表明,在反应气氛中加入SO_2和H2O后,催化剂比表面积和孔容均减小,副反应产物含有NH+4和SO_2-4。适量Cl离子可以抑制硫物种沉积,减少副反应产物生成,增强催化剂抗中毒能力。     

铝源对Ni/Al2 O3催化剂结构及其CO2-CH4重整性能的影响

以三种不同铝源采用溶液燃烧法制备了系列Ni/Al_2O_3催化剂,通过XRD、H_2-TPR、NH_3-TPD、N_2吸附-脱附、TGDTG和TPH等分析方法对反应前后催化剂进行了表征,研究了铝源对Ni/Al_2O_3催化剂结构、表面性质及其CO_2-CH_4重整性能的影响。结果表明,以Al(NO_3)_3·9H_2O为铝源制备的NiNO-AlNO催化剂比表面积较大,达102 m~2/g;高温还原峰面积大,峰型更为弥散;且载体Al_2_O_3具有一定的结晶性。而以Al_2(SO_4)_3·18H_2O和AlCl_3·6H_2O为铝源制备的NiNO-AlSO和NiNO-AlCl催化剂,其载体以无定型Al_2O_3存在,活性组分Ni晶粒粒径大、分散性差,还原峰面积较小,与载体的相互作用较弱。其中,由于硫酸铝较为稳定,需要在更高温度下才能转化为Al_2O_3,且所制备NiNO-AlSO催化剂中残留有含硫物质,使得其表面酸性较强。评价结果显示,NiNO-AlNO催化剂活性较高,稳定性好,CH4转化率为31.21%,CO_2转化率为48.97%。积炭分析结果发现,NiNO-AlNO催化剂表面积炭量最少,沉积炭主要以无定型态存在,具有良好的抗积炭性能。     

Mg改性对Co/γ-Al2O3-TiO2催化燃烧丙烷性能影响

采用分步浸渍法制备了系列Mg改性的Co/γ-Al_2O_3-TiO_2催化剂,通过X射线衍射(XRD)、紫外可见漫反射光谱(DR-UV-vis)、N_2吸附-脱附(BET)、X射线光电子能谱(XPS)和H_2程序升温还原(H_2-TPR)等技术对催化剂进行表征,并考察了其对丙烷燃烧的催化性能。结果表明,Co在原始γ-Al_2O_3-TiO_2载体和Mg改性MgO/γ-Al_2O_3-TiO_2载体上均以Co_3O_4的形式存在;Mg掺入后与Al_2O_3作用形成MgAl_2O_4尖晶石,改善了载体的织构性质,提升了Co_3O_4在催化剂载体表面的暴露数量和分散程度。此外,MgAl_2O_4与Co_3O_4相互作用提升了Co_3O_4颗粒表面Co~(3+)/Co~(2+)和O_(ads)/O_(latt)的比例,并削弱了Co-O键键能,从而提升了其对丙烷的催化燃烧活性。当Mg负载量为15%(质量分数)时,在Co/MgO(15%)/γ-Al_2O_3-TiO_2催化剂上进行丙烷燃烧,丙烷90%转化率的温度比无Mg掺杂的Co/γ-Al_2O_3-TiO_2催化剂的降低了45℃,并且连续反应40 h其活性保持稳定。