Determination of two antifouling booster biocides and their degradation products in marine sediments by high performance liquid chromatography-diode array detection

A method for the simultaneous determination of two antifouling booster biocides, diuron [1-(3,4-dichlorophenyl)-3,3-dimethylurea] and irgarol 1051 (2-methylthio-4-tert-butylamino-6-cyclopropylamino-s-triazine) and their degradation products, DCPMU [1-(3,4-dichlorophenyl)-3-methylurea], DCPU [1-(3,4-dichlorophenyl) urea], DCA [3,4-dichloroaniline] and M1 (2-methylthio-4-tert-butylamino-s-triazine), in marine sediments by high performance liquid chromatography-diode array detection (HPLC-DAD) was developed. The extraction of these compounds from sediment was achieved by means of methanolic ultrasonic extraction. The optimization of the extraction procedure included the variation of the volume of the extraction solvent, the amount of the extracted sediment, the duration and the temperature of sonication. C18 solid phase extraction (SPE) cartridges were used for the cleaning of the extracts. The relative standard deviations (R.S.Ds) of the developed procedure was <10% for all the tested compounds, except for DCA, where R.S.Ds up to 15% were obtained. Satisfactory recoveries were obtained (higher than 80% for all substances), except for DCA, which gave a recovery in the range of 35-50%. The limits of detection (LODs) of the substances varied between 1.7 (DCPU) and 4.0 (DCPMU) ng g⁻¹ of dry sediment.     

Effects of ultrasonic irradiation and direct heating on extraction of priority pesticides from marine sediments

Priority pesticides (alachlor, aldrin, γ-chlordane, chlorfenvinphos, chlorpyrifos, dieldrin, 4,4′-DDT, 4,4′-DDD, 4,4′-DDE, α-endosulfan, β-endosulfan, endosulfan sulphate, endrin, α-HCH, β-HCH, γ-HCH, δ-HCH, HCB, HCBD, heptachlor, heptachlor epoxide, isodrin, methoxychlor, mirex, quintozene, terbuthylazine and trifluralin) are a group of toxic substances that are known by their persistency in the aquatic environment. Their screening in marine sediments may provide information on the sources and distribution in the water mass of fresh-transitional and coastal waters. This work proposes a rapid and reliable method to extract multi-residues of priority pesticides by ultrasounds irradiation from marine sediments. Multiple variables have been optimised: ultrasound frequency, sonication intensity, signal operation mode, time of extraction and water bath temperature. After sample clean-up and pre-concentration of the pesticides by stir bar sorptive extraction, the compounds were analysed by gas chromatography-mass spectrometry (GC-MS) using the selective ion monitoring acquisition mode (SIM). Better performance was found for ultrasonic-assisted extractions (UAE) at frequency of 35 kHz and an output intensity of 60% in a sweep mode of operation. An increase of water bath temperature to 80°C had a significant effect on the extraction of pesticides with high octanol-water partitioning coefficients (K_ow). Under optimal conditions, method detection limits (MDLs) and method quantification limits (MQLs) ranged from 0.3 to 4.4 ng g^?1 and from 0.8 to 14 ng g^?1, respectively. Recoveries between 70 and 111%, at high precision levels, were found at different types of marine sediments with a single extraction cycle. Method performance was in good agreement with quality control guidelines.     

Determination of pesticides and their degradation products in soil: critical review and comparison of methods

Pesticides are applied widely to protect plants from disease, weeds and insect damage, and usually come into contact with soil, where they undergo a variety of transformations that provide a complex pattern of metabolites. This article reviews the most relevant analytical methods for determining pesticides and their transformation products in soils. We address some recent advances in sampling and sample-preparation technologies for soil analysis. We discuss and critically evaluate procedures, such as liquid extraction methods (pressurized liquid extraction or microwave-assisted extraction) and solid-phase based methods (headspace solid-phase microextraction, solid-phase microextraction or matrix-solid-phase dispersion). Analysis of pesticides is generally carried out by gas chromatography (GC) or liquid chromatography (LC) coupled to different detectors, especially to mass spectrometers (MSs). However, alternative and/or complementary methods, using capillary electrophoresis (CE), biosensors and bioassays have emerged recently. We also consider the advantages and the disadvantages of the various methodologies.     

Determination of atrazine, its degradation products and metolachlor in runoff water and sediments using solid-phase extraction

In order to determine the fate of the herbicides atrazine (as well as some of its degradation products) and metolachlor in water and sediments, a method was developed to extract and analyse these compounds. The two matrices were separated completely by centrifugation followed by filtration using nylon filters (0.45 mum). Sediments were extracted with a mixture of methanol-0.1N hydrochloric acid (50:50, v/v) using a wrist-action shaker. Filtered water and extracts of sediments were adjusted to pH 4, then concentrated and purified onto two solid-phase extraction cartridges using in tandem C(18) bonded phase column atop sulfonic acid bonded column (SCX). Atrazine, deethylatrazine, deisopropylatrazine and metolachlor retained by the C(18) column were eluted with ethyl acetate. Chlorodiaminotriazine and hydroxyatrazine retained by the SCX column were eluted with a 50:50 (v/v) acetonitrile-0.1M Na(2) HPO(4) aqueous solution (pH 8.5). The extracts were quantified by high performance liquid chromatography with diode array detector (HPLC-DAD) and by gas chromatography with nitrogen-phosphorus detector (GC-NPD). Overall percent recoveries were about 75% and detection limits were between 0.05 and 0.15 microg/l., and 0.5 and 1.5 microg/kg for water and sediments, respectively.     

超声辅助碱解萃取-气相色谱-电子捕获检测器测定海洋沉积物中8种多溴联苯醚

将超声辅助碱液分解杂质与溶剂萃取相结合,采用气相色谱-电子捕获检测(GC-ECD)建立了一种快速高效净化、萃取海洋沉积物中8种常见多溴联苯醚(PBDEs)的分析方法。样品在2.00 mol/L NaOH甲醇溶液中超声30 min,经正己烷萃取、单层硅胶净化、正己烷洗脱、旋蒸浓缩后定容至100 μL,采用GC-ECD分析。结果表明,PBDEs各单体的加标回收率为63.6%~110.3%,相对标准偏差(RSD)为1.7%~15.5%(n=5);十溴联苯醚(BDE-209)的检出限为0.097 ng/g,其他7种单体的检出限为0.002~0.011 ng/g(信噪比为3)。该方法的准确度和精密度较高,稳定性和回收率良好,可满足沉积物中PBDEs的分析要求。利用建立的方法测定了渤海表层沉积物中PBDEs的含量,8种PBDEs总含量在1.566~6.760 ng/g之间,其中BDE-209的含量为1.461~6.438 ng/g,总体呈现出由近岸向远岸递减的趋势,表明人为活动、表层冲刷和陆地河流的输入对渤海地区PBDEs的含量有重要影响。     

超声提取-超声波辅助固相微萃取色谱法测定蔬菜中的有机氯、菊酯类农药残留量

建立了一种USE-SPME-GC联用测定蔬菜中有机氯和菊酯类农药残留量的新方法,并对分析条件进行优化和探讨,实验表明,萃取液中基体杂质和色素对分析结果干扰较大,我们提出稀释的方法较好的解决这个问题。对实际蔬菜样品进行了测定和分析。     

Separation of chlorophylls and their degradation products in marine phytoplankton by reversed-phase high-performance liquid chromatography

Summary An RP-HPLC procedure which separates chlorophylls and their degradation products is described. By employing an amonium acetate buffered mobile phase and a linear gradient elution, complex mixtures of chloroand phaeopigments are separated in less than 30 minutes. The method has been applied to the control of chlorophyll enzymatic degradation in cultures of two algal species, and has also been successfully used in the analysis of algal xanthophylls.     

超声提取-气相色谱/质谱法测定皮革及纺织品中18种多环芳烃

采用超声波萃取技术对样品进行提取,气相色谱联用质谱(GC-MS)选择离子监测(SIM)模式采集数据,建立了皮革及纺织品中18种多环芳烃(PAHs)的分析方法.对色谱、质谱分析条件以及样品前处理条件进行研究与优化.在最优条件下,18种PAHs浓度在一定范围内与其峰面积呈现良好的线性关系,相关系数(R2)为0.9991～0...     

Determination of impurities in pesticides and their degradation products formed during the wine-making process by solid-phase extraction and gas chromatography with detection by electron impact mass spectrometry. I. Vinclozoline, procymidone and fenitrothion

The presence of degradation products of vinclozoline, procymidone and fenitrothion, and of impurities from their commercial formulations, was studied in white and red wines elaborated from spiked must. After solid-phase extraction the nature of the residues was established by gas chromatography with mass spectrometric detection. The structures of several degradation products and impurities are discussed and elucidated on the basis of their electron impact spectra. In elaborated wines the concentrations of the degradation products and impurities are lower than those of the original active ingredients. Aminofenitrothion and acetylamino-formyl-fenitrothion-oxon are the main residues of fenitrothion in wine. For dicarboximides, an alcohol derivative of vinclozoline was found in addition to 3,5-dichloroaniline.     

Determination of210Pb in sediments by extraction chromatography

A selective method is described for the determination of²¹⁰Pb in sediments, based on the separation of the daughter²¹⁰Bi by extraction chromatography with Microthene 710-tri-n-octylphosphine oxide (TOPO) and on a final source counting with a low background -counter. The average chemical yield is 92.0%. The detection limit for 2 g samples is 19 Bq kg^–1. An IAEA reference sediment sample was analyzed to check the reliability of the method.     

微波辅助萃取法测定烟草中有机氯类农药残留量

建立了一种微波辅助萃取-固相萃取净化测定烟草中17种有机氯类农药残留量的新方法. 样品用V(正己烷):V(乙酸乙酯)＝1:1提取, 提取液经Florisil固相萃取柱净化后, 采用气相色谱-电子捕获检测器(GC-μECD)进行检测. 17种有机氯农药的0.01、 0.05 mg/kg和0.5 mg/kg加标回收率均在82%以上, RSD在0.11%～8.2%之间, 能满足当前烟草中有机氯农药残留的检测要求.     

Determination of polycyclic aromatic hydrocarbons in marine sediments using a new ASE-SFE extraction technique

In order to determine PAHs in marine sediment samples by GC/MS(SIM) a new extraction approach of ASE-SFE was evaluated using combined accelerated solvent extraction (ASE, dynamic and static mode) and supercritical fluid extraction (SFE, dynamic mode) without further purification of the sample. The solvents used for ASE-SFE were methylene chloride and carbon dioxide. The recovery data, precision and accuracy of the whole method were evaluated statistically. The average recoveries of PAHs, based on deuterated internal standards were 77% for 2–3-ring PAHs, 85% for 4-ring PAHs, 88% for ¶5-ring PAHs and 97% for 6-ring PAHs. The extraction time required for the ASE-SFE technique was 30 min, which is longer than in the case of independent use of ASE and shorter compared to SFE. ASE-SFE recoveries of PAHs from SRM marine sediment are comparable for (2–3-ring, 4-ring PAHs) or higher (5-ring, 6-ring PAHs) than reported for the conventional extraction methods of ASE and SFE. Method detection limits of (MDL) were statistically estimated. MDL values obtained for 15 PAHs compounds vary between 0.06 ngg^?1 and 3.54 ngg^?1.     

Determination of polycyclic aromatic hydrocarbons in marine sediments using a new ASE-SFE extraction technique

In order to determine PAHs in marine sediment samples by GC/MS(SIM) a new extraction approach of ASE-SFE was evaluated using combined accelerated solvent extraction (ASE, dynamic and static mode) and supercritical fluid extraction (SFE, dynamic mode) without further purification of the sample. The solvents used for ASE-SFE were methylene chloride and carbon dioxide. The recovery data, precision and accuracy of the whole method were evaluated statistically. The average recoveries of PAHs, based on deuterated internal standards were 77% for 2-3-ring PAHs, 85% for 4-ring PAHs, 88% for 5-ring PAHs and 97% for 6-ring PAHs. The extraction time required for the ASE-SFE technique was 30 min, which is longer than in the case of independent use of ASE and shorter compared to SFE. ASE-SFE recoveries of PAHs from SRM marine sediment are comparable for (2-3-ring, 4-ring PAHs) or higher (5-ring, 6-ring PAHs) than reported for the conventional extraction methods of ASE and SFE. Method detection limits of (MDL) were statistically estimated. MDL values obtained for 15 PAHs compounds vary between 0.06 ngg(-1) and 3.54 ngg(-1).     

固相萃取-毛细管气相色谱法测定中草药及其土壤中多种有机氯农药残留量

建立了中草药及其土壤中多种有机氯农药残留量的固相萃取-毛细管气相色谱(SPE-CGC)分析方法,并对7种中草药及其土壤中多种有机氯农药残留量的相关性进行了初步研究。样品以正己烷-丙酮用超声波提取,Florisil(1 g)固相萃取小柱快速净化提取物。采用SPB-5弹性石英毛细管柱分离样品,GC-ECD检测7种中草药及其土壤中的13种有机氯农药的残留量。方法的线性范围为1.26×10-10~2.24×10-7g/mL;检出限为6.4×10-11~6.1×10-10g/mL;加样平均回收率为87.3%~104.4%(RSD为1.1%~7.0%)。     

Metal bioavailability in marine sediments measured by chemical extraction and enzymatic mobilization

In this work we compared metal bioavailable fractions in marine sediments operationally measured by sequential selective extractions (in particular the labile fraction released by acetic acid) and by a biomimetic approach using a commercially available proteolytic enzyme, proteinase K, chosen because of its non-specific behaviour and because it is representative of the enzymes encountered in many deposit-feeding organisms. Different experimental conditions for enzymatic extraction were investigated and the enzyme was employed both untreated and thermally denatured to study metal release mechanisms (i.e. enzymatic hydrolysis and/or complexation). Extractable protein content was also measured to verify possible correlations with some metals.Considering the two sediments used in this work, the available fraction evaluated with a biomimetic approach was often significantly lower than the fraction released by the first step of selective extractions, as expected. Moreover a good correlation was found between the fraction of metal available to the enzyme and enrichment factors in the gut fluids of deposit-feeding organisms, suggesting that enzymatic approach is qualitatively more reliable than chemical extraction in replicating the mechanism of metal mobilization that occurs in the guts of deposit-feeders.     

Metal bioavailability in marine sediments measured by chemical extraction and enzymatic mobilization

In this work we compared metal bioavailable fractions in marine sediments operationally measured by sequential selective extractions (in particular the labile fraction released by acetic acid) and by a biomimetic approach using a commercially available proteolytic enzyme, proteinase K, chosen because of its non-specific behaviour and because it is representative of the enzymes encountered in many deposit-feeding organisms. Different experimental conditions for enzymatic extraction were investigated and the enzyme was employed both untreated and thermally denatured to study metal release mechanisms (i.e. enzymatic hydrolysis and/or complexation). Extractable protein content was also measured to verify possible correlations with some metals.Considering the two sediments used in this work, the available fraction evaluated with a biomimetic approach was often significantly lower than the fraction released by the first step of selective extractions, as expected. Moreover a good correlation was found between the fraction of metal available to the enzyme and enrichment factors in the gut fluids of deposit-feeding organisms, suggesting that enzymatic approach is qualitatively more reliable than chemical extraction in replicating the mechanism of metal mobilization that occurs in the guts of deposit-feeders.     

Determination of linear alkylbenzene sulfonates and their polar carboxylic degradation products in sewage treatment plants by automated solid-phase extraction followed by capillary electrophoresis-mass spectrometry.

Linear alkylbenzene sulfonates (LAS) were determined by solid-phase extraction (SPE), followed by capillary electrophoresis and mass spectrometry detection (CE-MS). The linear range of the proposed method varied from 33 to 316 and from 215 to 2057 micrograms L-1, depending on the compound, with limits of detection ranging from 4.4 to 23 micrograms L-1 when 200 ml of wastewater were preconcentrated. The analysis and confirmation of the polar carboxylic metabolites of LAS, the sulfophenyl carboxylic acids (SPC) was also achieved, and their presence was detected in both, influent and effluents of the sewage treatment plant (STP). [M - H]- ions were used for CE-MS confirmation and quantification. CE-MS diagnostic ions were the same ones used in LC-electrospray (ESI)-MS and corresponded to m/z 297, 311, 325 and 339 for C10LAS, C11LAS, C12LAS and C13LAS, respectively. For SPC identification, diagnostic ions corresponded to m/z 215 to 369 (with 14 mass unit steps) for C2 to C13SPC, respectively. LAS were determined in wastewater samples of the influent and effluent of three sewage treatment plants (STP), two of them using biological treatment with secondary settlement and receiving mainly domestic wastewater whereas one of the plants was operated with physiochemical treatment and received mainly industrial wastewater. The concentration levels of total LAS varied from 1000 to 1900 micrograms L-1 in the influents of STP, whereas in the effluents the concentrations varied from 125 to 360 micrograms L-1.     

Part-per-trillion level determination of antifouling pesticides and their byproducts in seawater samples by off-line solid-phase extraction followed by high-performance liquid chromatography-atmospheric pressure chemical ionization mass spectrometry

A new method for the simultaneous determination of antifouling pesticides and some of their byproducts such as dichlofluanid, diuron and its byproducts [demethyldiuron and 1-(3,4-dichlorophenyl)urea], (2-thiocyanomethylthio)ben: zothiazole, chlorothalonil, Sea-nine 211, Irgarol 1051 and one of its byproducts (2-methylthio-4-tert.-butylamino-s-triazine) in seawater was developed. The extraction of these compounds from the filtered seawater samples was performed off-line with different solid-phase extraction sorbents using (I) a 500 mg graphitized carbon black cartridge (ENVI-Carb) and (II) 200 mg polymeric cartridges (LiChrolut EN and Isolute ENV+) and passing 500 ml of the sample through these cartridges. The detection was carried out by reversed-phase high-performance liquid chromatography coupled with atmospheric pressure chemical ionization mass spectrometry both in the negative and positive ion modes. The recovery ranged from 76 to 96% for the whole antifouling group with the ENVI-Carb cartridges and the detection limit was at the part-per-trillion level except for TCMTB. The method utilizing the polymeric cartridge proved to be very useful, time saving and with good recoveries when only Irgarol and its byproduct, Sea-nine 211 and diuron and its byproducts, have to be analyzed. The different cartridges were applied to the analysis of these pesticides in different marinas of the Catalan coast; diuron, dichlofluanid, Sea-nine 211, Irgarol as well as demethyldiuron and the Irgarol byproduct being the must ubiquitous pollutants. Maximum concentration levels were 2-3.5 microg/l of diuron and Sea-nine 211, respectively.     

Fast pressurized liquid extraction with in-cell purification and analysis by liquid chromatography tandem mass spectrometry for the determination of UV filters and their degradation products in sediments

This paper presents the development of a fast and sensitive analytical method for the simultaneous determination of UV filters and degradation products having quite different polarities (log Kow 2.19–6.88) in sediment, by means of pressurized liquid extraction (PLE) with in-cell purification and analysis by ultra-performance liquid chromatography (UPLC) coupled to tandem mass spectrometry (MS/MS). Analytes were simultaneously concentrated and purified by placing aluminium oxide as clean-up sorbent in the extraction cell for a faster sample pre-treatment. Under optimized conditions, quantitative recoveries (only one compound below 80%) and satisfactory precision (RSD, 5–15%) were obtained. Low limits of detection were achieved of 0.5–15 ng/g dry weight (dw). The use of PLE extraction and purification and UPLC technology enabled all the compounds to be separated chromatographically in less than 9 min, and with a total chromatographic analysis time of 18 min. This method significantly decreased the overall time of analysis as compared to those of previously developed. Finally, the optimized methodology was applied to investigate the occurrence of the target UV filters in sediment samples collected along the Ebro river basin (Spain). UV filters were detected in 95% of the sediment samples analysed. Results revealed a widespread presence of octocrylene (OC), reaching concentrations up to 24 × 10² ng/g dw, the highest reported so far. Ethylhexyl dimethyl PABA (OD-PABA) and benzophenone-3 (BP3) were also frequently detected (60–65%), but at lower concentrations (4.4–27 ng/g dw). 4DHB (an estrogenic degradation product of BP3) was present in three samples at concentrations between 12 and 21 ng/g dw. These results constitute the first data on the occurrence of OD-PABA and 4DHB in sediments.