反相乳液中Ag/TiO2纳米杂化粒子的制备及其SERS效应

在反相乳液的微环境中用一步反应法制备了Ag/TiO2纳米杂化粒子,并用TEM,SPS,XPS及XRD等方法进行了表征.结果表明,Ag粒子(5-15nm)已镶嵌在TiO2(30-50nm)结构中,并且具有SERS活性.     

HAS-硅钨杂多酸缔合纳米微粒体系的荧光猝灭

人血清白蛋白;瑞利散射;HAS-硅钨杂多酸缔合纳米微粒体系的荧光猝灭     

Formation and properties of composites based on microgels of a responsive polymer and TiO2 nanoparticles

Organic-inorganic composites were prepared with titanium dioxide (TiO2) nanoparticles embedded within colloidal particles of a cross-linked, thermally responsive polymer. To promote the incorporation of unaggregated nanoparticles of TiO2, temperature responsive microspherical gels (microgels) of N-isopropylacrylamide (NIPAM) with interpenetrating (IP) linear chains of poly(acrylic acid) (PAAc) were synthesized. Dynamic light scattering (DLS) measurements revealed that these microgels reversibly shrink and swell in diameter from 300-400 nm to 600-800 nm with temperature. Two types of nanoparticles of TiO2 were immobilized within the IP-microgels-fine TiO2 nanoparticles synthesized by the hydrolysis of titanium(IV) isopropoxide and commercially available Degussa P25. Characterization of the composite was conducted using transmission electron microscopy (TEM) and UV-vis absorption spectroscopy from which it was determined that the extent of loading of the TiO2 within the colloidal particles can be easily manipulated from a low value of 10% (weight) to a value as high as 75%. The TiO2 nanoparticles were in a dispersed state within the microgels and the composites showed rapid (approximately minutes) sedimentation, which is useful for gravity separations. By using turbidometry to characterize the settling behavior of the organic-inorganic composites, it was found that the settling time decreases as the content of TiO2 increases within the particles.     

Templated nucleation of hybrid iron oxide nanoparticles on polysaccharide nanogels

Novel organic–inorganic hybrid nanoparticles consisting of polymer–hydrogel nanoparticles (nanogels) and iron oxide were developed for potential biomedical applications. Hybrid nanoparticles were prepared by a simple procedure using polysaccharide nanogels as a reactive site for iron oxide formation. The hybrid nanoparticles have a narrow size distribution with a diameter of approximately 30 nm and show high colloidal stability. These nanohybrid particles could be used as a contrast medium for magnetic resonance imaging or for magnetic hyperthermia therapy.     

In situ controlled growth of well-dispersed gold nanoparticles in TiO2 nanotube arrays as recyclable substrates for surface-enhanced Raman scattering

In this paper, well-aligned Au-decorated TiO(2) nanotube arrays with high surface-enhanced Raman scattering (SERS) enhancement were prepared using a facile in situ reduction and controlled growth approach. The gold nanoparticles are well-dispersed and assembled on the mouth surface and the inside of the TiO(2) nanotubes without clogging. The structure and optical properties of the Au-decorated TiO(2) nanotube arrays have been characterized. The Au-decorated TiO(2) nanotube arrays were employed as SERS-active substrates, which exhibit good performance due to long-range coupling between Au nanoparticles, and TiO(2)-assisted enhanced charge-transfer from Au to Rh6G. The SERS activity of the substrates strongly depends on the crystallite size and level of aggregation. The substrates display significant fluorescence quenching ability and uniform SERS responses throughout the whole surface area. Particularly, good recyclability is shown. The photocatalytic property of Au-decorated TiO(2) nanotube array was exploited to recycle the substrate through UV light photocatalytic purification. The experimental results showed that the substrate is featured by high reproducibility and can be used as a highly efficient SERS substrate for multiple detection of different chemical and biological molecules.     

Effect of nanoparticle aggregation at low concentrations of TiO2 on the hydrophilicity, morphology, and fouling resistance of PES-TiO2 membranes

This paper reports the fabrication and characterization of polyethersulfone-TiO(2) (PES-TiO(2)) nanoparticle composite membranes made from synthesis casting solution consisting of various compositions of polymer solvents (DMF and EtOH) and TiO(2) additive. The results also revealed that the membrane permeation and rejection rates, pore size, and porosity were dependent on the TiO(2) and EtOH concentrations. Nanoparticles were characterized by zeta potential measurements, TEM observations, and measurement of particle size distributions. Zeta potential measurements in aqueous solution demonstrated that the TiO(2) particles size is dominated by electric double layer interactions. Addition of EtOH promotes the increase of the clusters size as consequence of a double effect: reduction of the dielectric constant of solution and the depletion of the suspension field determined by the action of the polymer chains. The observed effects as result of EtOH addition and increase of TiO(2) concentration were similar: both procedures provoked an increase of macrovoid dimensions. The modified membranes by TiO(2) incorporation showed a structural change from a sponge-like to a finger-like structure. Strong correlations were observed between the hydrophilicity and the permeability of manufactured membranes. The formation mechanism of TiO(2)-blended membranes was altered, in a similar way, as result of EtOH at different contents of nanoparticles. Fouling resistance of modified membranes was significantly improved showing that EtOH addition is a suitable procedure for the membrane performance improvement. The rejection potential of membranes is hardly affected by the nanoparticles and EtOH incorporation into the polymeric solution.     

Optical modeling of nanocrystalline TiO2 films

The light transmittance, T, in nanocrystalline TiO2 films was studied as a function of the light wavelength, lambda, the nanocrystal radius, a, and the film thickness, d. Two types of TiO2 nanoparticles were employed: a commercial powder (P25) and synthesized particles from titanium isopropoxide (SP). The X-ray diffraction measurements revealed that both P25 and SP are mainly anatase and the average crystal sizes, 2a, of P25 and SP are 50.3 and 23.7 nm, respectively. Despite the visual difference between micron-order thin films of P25 and SP, the light hemispherical transmittance corrected with the surface specular reflectance has a clear dependence of ln(T) = -0.5beta lambda(-4)a(3)d, with beta = 1.5 x 10(3) from visible to near-infrared wavelengths. The dependence and beta value were successfully explained by the simplest model on the basis of the Rayleigh scattering theory. This indicates that the nanocrystalline TiO2 thin films are a typical medium where the simplest scattering model is a good approximation. However, the model was inapplicable to light scattering in relatively thick P25 films of 1.5-3.0 microm because of nonnegligible internal multiple scattering. For the moderate thickness films, ln(T) proportional to lambda(gamma), where gamma increases from -4 in proportion to the film thickness is an alternative approximation. With these light scattering models, the light absorption rate of the TiO2 crystal was successfully evaluated from experimental extinction rates.     

Modification of the morphology of P(S-b-EO) templated thin TiO2 films by swelling with PS homopolymer

For the controlled modification of sol-gel-templated polymer nanocomposites, which are transferred to a nanostructured, crystalline TiO2 phase by a calcination process, the addition of a single homopolymer was investigated. For the preparation, the homopolymer polystyrene (PS) is added in different amounts to the diblock copolymer P(S-b-EO) acting as a templating agent. The homopolymer/diblock copolymer blend system is combined with sol-gel chemistry to provide and attach the TiO2 nanoparticles to the diblock copolymer. So-called good-poor solvent-pair-induced phase separation leads to the formation of nanostructures by film preparation via spin coating. The fabricated morphologies are studied as a function of added homopolymer before and after calcination with atomic force microscopy, field emission scanning electron microscopy, and grazing incidence small-angle X-ray scattering. The observed behavior is discussed in the framework of controlling the block copolymer morphologies by the addition of homopolymers. At small homopolymer concentrations, the increase in homopolymer concentration changes the structure size, whereas at high homopolymer concentrations, a change in morphology is triggered. Thus, the behavior of a pure polymer system is transferred to a more complex hybrid system.     

Bicontinuous ceramics with high surface area from block copolymer templates

Mesoporous polymers with gyroid nanochannels can be fabricated from the self-assembly of degradable block copolymer, polystyrene-b-poly(L-lactide) (PS-PLLA), followed by hydrolysis of PLLA block. Well-defined polymer/ceramic nanohybrid materials with inorganic gyroid nanostructures in a PS matrix can be obtained by using the mesoporous PS as a template for sol-gel reaction. Titanium tetraisopropoxide (TTIP) is used as a precursor to give a model system for the fabrication of metal oxide nanostructures from reactive transition metal alkoxides. By controlling the rates of capillary-driven pore filling and sol-gel reaction, the templated synthesis can be well-developed. Also, by taking advantage of calcination, bicontinuous TiO(2) with controlled crystalline phase (i.e., anatase phase) can be fabricated after removal of the PS template and crystallization of TiO(2) by calcination leading to high photocatalytic efficiency. This new approach provides an easy way to fabricate high-surface-area and high-porosity ceramics with self-supporting structure and controlled crystalline phase for practical applications. As a result, a platform technology to fabricate precisely controlled polymer/ceramic nanohybrids and mesoporous ceramic materials can be established.     

Preparation of highly uniform Ag/TiO2 and Au/TiO2 supported nanoparticle catalysts by photodeposition

Photodeposition of Ag nanoparticles on commercial TiO2 particles and nanoparticles was performed in order to provide direct visualization of the spatial distribution of photoactive sites on sub-micrometer-scale and nanoscale TiO2 particle surfaces and to create materials for potential catalytic applications. HRTEM (high-resolution transmission electron microscopy) and HAADF-STEM (high-angle annular dark-field scanning transmission electron microscopy) were used to characterize these materials. The size and spatial distributions of the Ag nanoparticles on the commercial TiO2 were not uniform; the concentration of Ag was higher on grain boundaries and at the edges of these submicrometer particles. In the case of TiO2 nanoparticles, the size distribution of the Ag nanoparticles deposited was relatively uniform and independent of irradiation time and photon energy. The amount of Ag deposited on TiO2 nanoparticles was at least 6 times higher than that on the commercial samples for comparable irradiation conditions. Compared to the case of Ag photodeposition, the difference in the amount of Au photodeposited on TiO2 particles and nanoparticles was even greater, especially at low precursor concentrations. Photodeposition on TiO2 nanoparticles is suggested as a potential method for the preparation of Au/TiO2 catalysts, as loadings in excess of 10 wt % of uniform 1 nm metal particles were achieved in this work.     

TiO_2-SiO_2纳米粒子的合成及二级散射光谱法测定核糖核酸

采用溶胶-凝胶法制备了TiO2-SiO2纳米粒子.通过X-射线衍射谱、透射电子显微镜等对纳米粒子进行了表征.研究了TiO2-SiO2纳米粒子与核糖核酸(RNA)的相互作用,建立了基于纳米粒子与RNA吸附反应,二级散射光谱法测定痕量RNA的新方法.方法的线性范围是0.005～5 mg/L; 检出限为1.46 μg/L.方法用于RNA合成样品的测定,回收率为99.4%～103.9%;相对标准偏差为019%～0.24%.     

Agglomeration and sedimentation of TiO2 nanoparticles in cell culture medium

The physicochemical characterization of nanoparticles in suspension is a prerequisite for the adequate assessment of their potential biological effect. Little is known to date about the colloidal stability of TiO2 nanoparticles in cell culture medium. This study investigates the effect of particle concentration, ionic strength, pH, and the presence of fetal bovine serum (FBS) and human serum albumin (HSA) on the colloidal stability of TiO2 nanoparticles in RPMI cell culture medium, by sedimentation measurements, dynamic light scattering, and electrokinetic measurements (zeta-potential). TEM revealed that the particles were polydisperse, with diameters ranging from approximately 15 to approximately 350 nm. The agglomeration rate and sedimentation rate increased with particles' concentration. The size of the agglomerates at 100 mg/L TiO2 was significantly reduced, from 1620+/-160 to 348+/-13 and 378+/-15 nm, upon the addition of 10% (v/v) FBS and 1% (w/w) HSA, respectively. The isoelectric point of TiO2 in water was 2.9 and the measured zeta-potential in RPMI was -16+/-2 mV at pH 7.4. A slight increase in the zeta-potential of TiO2 in RPMI was observed upon the addition of FBS and HSA. The addition of FBS and HSA prevented high agglomeration, leading to a stable dispersion of TiO2 nanoparticles for at least 24 h, possibly due to steric stabilization of the particles.     

Pluronics‐Stabilized Gold Nanoparticles: Investigation of the Structure of the Polymer–Particle Hybrid

Hybrid gold–polymer nanoparticles are obtained by self‐assembly of amphiphilic copolymers (Pluronics) in solutions containing preformed gold nanoparticles (diameter ca. 12 nm). Dynamic light scattering, TEM, cryo‐TEM, and small‐angle neutron scattering experiments with contrast variation are used to characterize the structure of the gold–polymer particles. Five Pluronics (F127, F68, F88, F108, P84) with different molecular weights and hydrophilic/hydrophobic balances are investigated. Gold nanoparticles are individually embedded within globules of polymer, even under conditions for which Pluronics micelles do not form in solution. The hybrid particles are several tens of nanometers in size (larger than micelles of the corresponding Pluronics), and the size can be tuned by changing the temperature.     

On the morphology and stability of Au nanoparticles on TiO2(110) prepared from micelle-stabilized precursors

The morphology and stability of well-ordered, nanostructured Au/TiO2(110) surfaces, prepared by deposition of Au loaded micelles on TiO2(110) substrates and subsequent oxidative removal of the polymer shell in an oxygen plasma, was investigated by noncontact AFM, SEM and XPS. The resulting arrays of Au nanoparticles (particle sizes 1-5 nm) form a nearly hexagonal pattern with well-defined interparticle distances and a narrow particle size distribution. Particle size and particle separation can be controlled independently by varying the Au loading and the block-copolymers in the micelle shell. The oxygen plasma treatment does not affect the size and distance of the Au nanoparticles; the latter are fully metallic after subsequent UHV annealing (400 degrees C). The particles are stable under typical CO oxidation reaction conditions, up to at least 200 degrees C, making these surfaces ideally suited as defined model systems for catalytic studies. Significant changes in the height distributions of the Au nanoparticles are found upon 400 degrees C annealing in O2. For adlayers with small interparticle distances, this leads to a bimodal particle size distribution, which together with the preservation of the lateral order points to Ostwald ripening.     

Rational design of 3D dendritic TiO2 nanostructures with favorable architectures

Controlling the morphology and size of titanium dioxide (TiO(2)) nanostructures is crucial to obtain superior photocatalytic, photovoltaic, and electrochemical properties. However, the synthetic techniques for preparing such structures, especially those with complex configurations, still remain a challenge because of the rapid hydrolysis of Ti-containing polymer precursors in aqueous solution. Herein, we report a completely novel approach-three-dimensional (3D) TiO(2) nanostructures with favorable dendritic architectures-through a simple hydrothermal synthesis. The size of the 3D TiO(2) dendrites and the morphology of the constituent nano-units, in the form of nanorods, nanoribbons, and nanowires, are controlled by adjusting the precursor hydrolysis rate and the surfactant aggregation. These novel configurations of TiO(2) nanostructures possess higher surface area and superior electrochemical properties compared to nanoparticles with smooth surfaces. Our findings provide an effective solution for the synthesis of complex TiO(2) nano-architectures, which can pave the way to further improve the energy storage and energy conversion efficiency of TiO(2)-based devices.     

Self‐emulsion polymerization of amphiphilic monomers—a green route to synthesis of polymeric nanoscaffolds

Self‐emulsion polymerization (SEP), a green route developed by us for the polymerization of amphiphilic monomers, does not require any emulsifier or an organic solvent except that the water‐soluble initiators such as 2,2′‐azobis[2‐(2‐imidazolin‐2‐yl)propane]dihydrochloride (VA‐044) and potassium persulfate (KPS) are only used. We report here the polymer nanoscaffolds from a number of amphiphilic monomers, which can be used for in situ encapsulation of a variety of nanoparticles. As a demonstration of the efficacy of these nanoscaffolds, the synthesis of a biocompatible hybrid nanoparticle (nanohybrid), prepared by encapsulating Fe₃O₄ magnetic nanoparticle (Fe₃O₄ MNPs) in poly(2‐hydroxyethyl methacrylate) in water, for MRI application is presented. The nanohybrid prepared following the SEP in the form of an emulsion does not involve the use of any stabilizing agent, crosslinker, polymeric emulsifier, or surfactant. This water‐soluble, spherical, and stable nanohybrid containing Fe₃O₄ MNPs of average size 10 ± 2 nm has a zeta potential value of ?41.89 mV under physiological conditions. Magnetic measurement confirmed that the nanohybrid shows typical magnetic behavior having a saturation magnetization (Ms) value of 32.3 emu/g and a transverse relaxivity (r2) value of 29.97 mM^?1 s^?1, which signifies that it can be used as a T2 contrast agent in MRI. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2019     

Enhanced photocatalytic degradation of C.I. Basic Violet 2 using TiO2-SiO2 composite nanoparticles

In this report, TiO(2) -SiO(2) composite nanoparticles were prepared by the thermal hydrolysis method using titanium tetrachloride and tetraethylorthosilicate as TiO(2) and SiO(2) precursors, respectively. The prepared nanoparticles were characterized by X-ray powder diffraction (XRD), Fourier-transform infrared spectroscopy (FT-IR), scanning electron microscopy (SEM), energy dispersive X-ray spectroscopy (EDX), nitrogen adsorption/desorption and UV-Vis diffuse reflectance spectroscopy (DRS). The results indicated that, in comparison with pure TiO(2), TiO(2)-SiO(2) composite nanoparticles had a higher thermal stability, which prevents phase transformation from anatase to rutile. In addition, the TiO(2)-SiO(2) nanoparticles had a higher specific surface area, larger pore volume, greater band gap energy and smaller crystallite size. Thus, the surface area of TiO(2)-40% SiO(2) composite nanoparticles was about 17 times higher than that of pure TiO(2) nanoparticles. The photocatalytic activity of TiO(2)-SiO(2) composite nanoparticles in the photodegradation of C.I. Basic Violet 2 was investigated. The photodegradation rate of Basic Violet 2 using TiO(2)-40% SiO(2) nanoparticles calcined at 600°C was much faster than that using pure TiO(2) and Degussa P25 TiO(2) by 10.9 and 4.3 times, respectively. The higher photoactivity of the TiO(2)-SiO(2) composite nanoparticles was attributed to their higher surface area, larger pore volume, greater band-gap energy and smaller crystallite size compared with pure TiO(2).     

Gold-Titanium(IV) Oxide Plasmonic Photocatalysts Prepared by a Colloid-Photodeposition Method: Correlation Between Physical Properties and Photocatalytic Activities

Colloidal gold (Au) nanoparticles were prepared and successfully loaded on titanium(IV) oxide (TiO(2)) without change in the original particle size using a method of colloid photodeposition operated in the presence of a hole scavenger (CPH). The prepared Au nanoparticles supported on TiO(2) showed strong photoabsorption at around 550 nm due to surface plasmon resonance (SPR) of Au and exhibited a photocatalytic activity in mineralization of formic acid in aqueous suspensions under irradiation of visible light (>ca. 520 nm). A linear correlation between photocatalytic activity and the amount of Au loaded, that is, the number of Au nanoparticles, was observed, indicating that the activity of Au/TiO(2) plasmonic photocatalysts can be controlled simply by the amount of Au loading using the CPH method and that the external surface area of Au nanoparticles is a decisive factor in mineralization of formic acid under visible light irradiation. Very high reaction rates were obtained in samples with 5 wt % Au or more, although the rate tended to be saturated. The CPH method can be widely applied for loading of Au nanoparticles on various TiO(2) supports without change in the original size independent of the TiO(2) phase. The rate of CO(2) formation also increased linearly with increase in the external surface area of Au. Interestingly, the TiO(2) supports showed different slopes of the plots. The slope is important for selection of TiO(2) as a material supporting colloidal Au nanoparticles.     

Nanoparticle self-assembled hollow TiO(2) spheres with well matching visible light scattering for high performance dye-sensitized solar cells

Submicrometer-sized hollow TiO(2) spheres are directly self-assembled from TiO(2) nanoparticles without using any template or surfactant as a scattering layer for dye-sensitized solar cells, showing good visible light scattering match to significantly improve the photoconversion efficiency.     

Determining the hydrodynamic radii of AOT micelles with silver nanoparticles by means of photon correlation spectroscopy

The possibility of determining the sizes of micelles of sodium di(2-ethylhexyl)sulfosuccinate (AOT) with silver nanoparticles in decane against the background of a large excess of empty micelles by means of photon correlation spectroscopy with unimodal analysis of the autocorrelation function is demonstrated. Contributions from all components to the light scattering are estimated by measuring the static (Rayleigh) light scattering and allowing for partial absorption of the laser radiation by silver nanoparticles. Areas of the correct determination of the hydrodynamic radius of the micelles with nanoparticles are determined via unimodal analysis of the autocorrelation function in dependence on the nanoparticle size (10–2 nm) and silver concentration (1–30 mM) at a constant AOT concentration (0.25 mol/L) and aqueous pseudophase content (1 vol %).