改性炭黑-LaMnO3复合材料的制备及其共价复合效应对氧还原性能的影响

以VulcanXC-72炭黑为载体,通过对炭载体石墨化处理和表面化学修饰,将其与化学沉淀法制备的纳米级LaMnO₃颗粒共混,再经特定温度下煅烧,制备出改性炭黑-LaMnO₃复合材料.X射线光电子能谱和热重分析表明,当煅烧温度在300℃时,炭载体与LaMnO₃纳米颗粒之间形成了大量C-O-M（M=La,Mn）化学键.扫描电子显微镜和高分辨透射电子显微镜分析发现,纯相LaMnO₃纳米颗粒主要呈现短棒、三支棒或竹节棒的形貌特征,炭载体则为具有完整石墨层的空心球结构,LaMnO₃均匀分散在炭载体上.在25℃,1mol/LNaOH溶液中的电化学测试结果表明,成分比（LaMnO₃：C）为2：3的复合材料具有很高的氧还原电催化活性,氧还原反应电子数为3.81,中间产物H₂O₂产率为9.5%,其活性接近商业Pt/C催化剂（E-TEK）.高的氧还原电催化活性主要归因于LaMnO₃纳米颗粒与炭载体之间形成了大量共价键.     

Carbon-supported Fe/Co-N electrocatalysts synthesized through heat treatment of Fe/Co-doped polypyrrole-polyaniline composites for oxygen reduction reaction

In this paper,we synthesized cathode catalysts(PANI-PPYR,Fe/PANI-PPYR,Co/PANI-PPYR and Fe-Co/PANI-PPYR)with high performance oxygen reduction by using a simple heat treatment process.These catalysts were fabricated by directly calcining the Fe and/or Co doped polyaniline(PANI)-polypyrrole(PPYR)composites.Their electrocatalytic activity for ORR both in acidic and in alkaline media was investigated by voltammetric techniques.Among the prepared catalysts,Co/PANI-PPYR presents the most positive ORR onset potential of 0.62 V(vs.SCE)in 0.5 mol/L H2SO4 solution or?0.09 V(vs.SCE)in 1 mol/L NaOH solution.In addition,the Co/PANI-PPYR catalyst shows the largest limiting-diffusion current density for ORR,which is 4.3 mA/cm2@0.2 V(vs.SCE)in acidic and 2.3 mA/cm2@?0.3 V(vs.SCE)in alkaline media.In acidic media,a four-electron reaction of ORR on the Co/PANI-PPYR and Fe/PANI-PPYR catalysts is more dominant than a two-electron reaction.In alkaline media,however,a four-electron and a two-electron mechanisms are co-present for the ORR on all the prepared catalysts.Co/PANI-PPYR catalyst also presents good electrocatalytic activity stability for ORR both in acidic and in alkaline media.     

纳米碳纤维的表面性质和微结构对氧还原催化活性的影响

采用超声处理的方法分别对管式纳米碳纤维(t-CNF)和鱼骨式纳米碳纤维(f-CNF)进行了表面化学处理. XPS结果表明, 在混酸(浓硫酸+浓硝酸)和氨水中进行超声化学处理可以在CNF表面分别引入含氧官能团和含氮官能团. 电化学测试结果表明, 2种不同微结构CNF的氧还原催化活性都遵循相同的趋势, 即CNF-P相似文献   

High performance Fe and N-codoped graphene quantum dot supported Pd3Co catalyst with synergistically improved oxygen reduction activity and great methanol tolerance

Designing high-performance and durable non-platinum catalysts as oxygen reduction reaction (ORR) catalysts is still a major barrier of fuel cell commercialization. In this work, simple hydrothermal and impregnation routes were applied to prepare non-platinum Pd-Co bimetallic nano-catalysts such as Fe-N doped graphene quantum dot (Fe-N-GQD) supported Pd₃Co (Pd₃Co/Fe-N-GQD 10 wt%), carbon supported Pd₃Co/C (10 wt%), graphene quantum dot supported Pd₃Co/C (10 wt%). The synthesized catalysts were physico-chemically characterized by X-ray diffraction (XRD), Raman spectroscopy, transmission electronmicroscopy (TEM), and X-ray photoelectron spectroscopy (XPS). The electrochemical investigation was carried out in three electrode half-cell system to evaluate the catalyst activity for oxygen reduction reaction (ORR), the tolerance to methanol crossover and durability. In comparison to commercial Pt/C (ETEK, 20 wt%), the Pd₃Co/Fe-N-GQD with lower weight percentage catalyst (∼10 wt%) displayed comparable electrocatalytic activity toward ORR with even higher methanol-tolerance capability and durability. The fabricated Pd₃Co/Fe-N-GQD with (10 wt %) metal loading exhibited only 20% lower activity than Pt/C (ETEK, 20 wt%) toward ORR. Nevertheless the durability study of the catalyst in acidic media showed that the Pd₃Co/Fe-N-GQD preserve 40% of its activity while Pt/C (ETEK, 20 wt%) exhibited only 20% of its initial catalytic activity for ORR. Moreover the activity loss in the presence of methanol (0.1 M) was obtained for Pt/C (ETEK, 20 wt%) and Pd₃Co/Fe-N-GQD 35% and 14%, respectively. To investigate the role of catalyst support, catalytic activities of Pd₃Co/Fe-N-GQD, Pd₃Co/C, Pd₃Co/GQD and Pd/Fe-N-GQD were compared. The results demonstrated superior catalytic activity of Pd₃Co/Fe-N-GQD which could be related to the cocatalytic role of Fe-N-GQD due to the presence numerous of active sites exposed to the reactants.     

Electrochemical performance of annealed cobalt-benzotriazole/CNTs catalysts towards the oxygen reduction reaction

One of the major limitations yet to the global implementation of polymer electrolyte membrane fuel cells (PEMFCs) is the cathode catalyst. The development of efficient platinum-free catalysts is the key issue to solve the problem of slow kinetics of the oxygen reduction reaction (ORR) and high cost. We report a promising catalyst for ORR prepared through the annealing treatment under inert conditions of the cobalt-benzotriazole (Co-BTA) complex supported on carbon nanotubes (CNTs). The N-rich benzotriazole precursor was chosen based on its ability to complex Co(II) ions and generate under annealing highly reactive radicals able to tune the physicochemical properties of CNTs. X-Ray photoelectron spectroscopy (XPS) was used to follow the surface structure changes and highlight the active electrocatalytic sites towards the ORR. To achieve further evaluation of the catalysts in acidic medium, voltamperometry, rotating disk electrode (RDE), rotating ring-disk electrode (RRDE) and half-cell measurements were performed. The resulting catalysts (Co/N/CNTs) all show catalytic activity towards the ORR, the most active one resulting from annealing at 700 °C. The overall electron transfer number for the catalyzed ORR was determined to be ～3.7 with no change upon the catalyst loading, suggesting that the ORR was dominated by a 4e(-) transfer process. The results indicate a promising alternative cathode catalyst for ORR in fuel cells, although its performance is still lower (overpotential around 110 mV evaluated by RDE and RRDE) than the reference Pt/C catalyst.     

Mn-N-C催化剂的制备及其在碱性介质中对氧还原反应的电催化性能

选用壳聚糖(CS)为原料制备了壳聚糖水杨醛席夫碱锰配合物(Mn-CS-sal)。将Mn-CS-sal配合物负载于石墨碳上得到碳载配合物(Mn-CS-sal/C),后经高温热处理得到Mn-N-C目标催化剂(Mn-N-C-t,t=200、400、600、800、1 000℃)。采用FT-IR、XRD、XPS和电化学等方法对催化剂的组成和结构进行了表征,对其在氧还原反应中的电催化性能进行了研究。结果表明,所得到的Mn-N-C催化剂对氧还原反应(ORR)具有很好的催化作用,但以600℃热处理制备的催化剂其活性最好。催化剂中Mn-N-C结构是催化ORR的活性位。采用循环伏安法获得了Mn-N-C-t催化ORR的动力学参数,即总的转移电子数n和电子传递系数αnα;具有最佳活性的Mn-N-C-600催化剂的总转移电子数为3.63,说明在此条件下,Mn-N-C-600催化ORR主要以4e转移途径为主,由此提出了可能的氧还原反应的机理。     

Electrocatalysis of oxygen reduction on multi-walled carbon nanotube supported copper and manganese phthalocyanines in alkaline media

Manganese phthalocyanine (MnPc) and copper phthalocyanine (CuPc)-modified electrodes were prepared using multi-walled carbon nanotubes (MWCNTs) as a support material. The catalyst materials were heat treated at four different temperatures to investigate the effect of pyrolysis on the oxygen reduction reaction (ORR) activity of these electrocatalysts. The MWCNT to metal phthalocyanine ratio was varied. Scanning electron microscopy (SEM) was employed to visualise the surface morphology of the electrodes and the x-ray photoelectron spectroscopic (XPS) study was carried out to analyse the surface composition of the most active catalyst materials. The ORR was studied in 0.1 M KOH solution employing the rotating disk electrode (RDE) method. Glassy carbon (GC) electrodes were modified with carbon nanotube-supported metal phthalocyanine catalysts using Tokuyama AS-4 ionomer. The RDE results revealed that the highest electrocatalytic activity for ORR was achieved upon heat treatment at 800 °C. CuPc-derived catalyst demonstrated lower catalytic activity as compared to the MnPc-derived counterpart, which is in good agreement with previous literature, whereas the activity of MnPc-based catalyst was higher than that reported earlier.     

弱磁性Co0.85Se纳米片负载碳纳米管作为电催化析氢催化剂

氢气是一种环境友好可再生的清洁能源,电解水无疑是一种很好的制氢方法.然而,电催化分解水析氢受到其缓慢的动力学过程、较低的催化性能和较差的稳定性的限制.为了使整个过程更节能,具有高电流密度和低的过电势的高效电催化剂被广泛研究.非化学计量相硒化钴(Co0.85Se)作为一种重要的金属硫属化合物具有优异的催化性能而广受关注.但是低维的Co0.85Se活性位点少,分散性差,电子传递能力低,导致其电催化剂活性差.多壁碳纳米管(MWCNTs)具有多种电性能,包括金属导电性和电子存储能力等.因此,MWCNTs的特殊结构和高导电性可以有效地促进电子从电催化剂向碳纳米管的转移,实现高效电分解水制氢性能.本文在不使用表面活性剂和模板的情况下,通过一步水热溶剂热法合成弱磁性Co0.85Se纳米片负载碳纳米管电催化剂.采用磁滞回线研究Co0.85Se和MWCNTs/Co0.85Se的磁性能,结果表明其有弱顺磁性,Co0.85Se纳米片之间的空间距离增强导致粒子间偶极相互作用减弱,从而使MWCNTs/Co0.85Se纳米复合材料的矫顽力值增加到158 Oe.随着微晶尺寸的减小和纳米颗粒间距的增大,MWCNTs/Co0.85Se催化剂的比表面积增大,有利于提高其电催化活性.扫描电镜和透射电镜展示出Co0.85Se纳米片分散性较差,且团聚现象严重,而MWCNTs/Co0.85Se纳米复合催化剂显示Co0.85Se纳米片均匀分散在MWCNTs表面,且纳米片尺寸明显减小,有利于Co0.85Se纳米片暴露更多的活性位点.线性扫描伏安曲线测量表明,在酸性溶液中Co0.85Se纳米片在电流密度为10 mA cm?2时,其过电势为319 mV(vs.RHE),30 wt%MWCNTs/Co0.85Se的过电势为266 mV(vs.RHE).Co0.85Se和MWCNTs/Co0.85Se的Tafel斜率分别为92.6和60.5 mV dec?1.此外,MWCNTs/Co0.85Se的电流交换密度(j0)为0.07 mA cm?2.较小的Tafel斜率和高的电流交换密度表明,MWCNTs/Co0.85Se具有良好的反应动力学和快速的质子分离速率.交流阻抗谱表明MWCNTs/Co0.85Se比Co0.85Se电阻更小,电子传输速率更快.电化学活性表面积与双电层在固液界面处的电容测量值成正比.结果显示,30 wt%MWCNTs/Co0.85Se的双电层电容为0.22 mF cm^-2,高于Co0.85Se和15 wt%的rGO/Co0.85Se(0.04 mF cm^-2,0.17 mF cm^-2),这表明较大的电化学活性表面积有利于析氢反应进行.30 wt%MWCNTs/Co0.85Se的循环稳定测试表明其具有较好的稳定性.综上,本文介绍了通过一步水热法合成具有弱磁性的Co0.85Se和MWCNTs/Co0.85Se电催化剂,碳纳米管作为一种高导电性材料被引入Co0.85Se纳米片中以减少Co0.85Se的团聚,使Co0.85Se的活性位点增加,进而提高电催化制氢性能.     

高温处理对碳载吡啶钴催化氧还原性能的影响

利用碳黑(Vulcan XC-72R) 中加入硫酸钴和吡啶(Py)作为催化剂前躯体, 经溶剂分散热处理构建了一类新型的高效氧还原CoPy/C复合催化剂. 运用循环伏安法和旋转圆盘电极(RDE)技术研究了不同温度(600~900 ℃)处理CoPy/C催化剂在碱性介质中对氧还原的电催化性能. 结果表明, 热处理能显著提高CoPy/C的催化活性, 活性次序为800 ℃>900 ℃>600 ℃>未处理. 其中800 ℃处理的15%Co25%Py/C(质量分数)复合催化剂表现出最佳的氧还原催化性能, 以其制备的气体扩散电极在3.0 mol/L KOH 电解质溶液(O₂气氛)中的半波电位为-0.069 V(相对于标准可逆氢电极), 起峰电位为0.026 V, 同时表现出明显的极限扩散电流. 利用透射电镜、 能谱分析和X射线衍射技术对催化剂的微观形貌、 颗粒大小和活性位结构的研究结果表明, 所制备的碳黑负载吡啶钴催化剂(15%Co25%Py/C)平均粒径为17 nm, 经800 ℃处理后吡啶结构发生了坍塌, 形成了其它价态的钴氧化合物、 硫化物和单质钴, 并协同吡啶中的氮对氧起催化还原作用. RDE结果表明, O₂在CoPy/C催化剂上的反应动力学主要通过4e^-过程还原成H₂O.     

直接甲酸燃料电池氧还原碳载Au-Ir催化剂的电催化性能

用四氢呋喃(THF)络合还原法分别合成并比较了碳载金(Au/C)、碳载铱(Ir/C)、碳载金-铱(Au-Ir/C)催化剂对氧气还原和甲酸氧化的电催化活性.发现3种催化剂对甲酸氧化都没有电催化活性;Au-Ir/C催化剂对氧还原的电催化活性要远好于Au/C和Ir/C催化剂.表明Au-Ir/C催化剂适合作为直接甲酸燃料电池(DFAFC)的阴极催化剂.     

Synthesis and characterization of iron‐ and nitrogen‐functionalized graphene catalysts for oxygen reduction reaction

Iron‐ and nitrogen‐functionalized graphene (Fe‐N‐G), as well as iron‐ and nitrogen‐functionalized oxidized graphene (Fe‐N‐Gox) catalysts were synthesized as non‐noble metal electrocatalysts for oxygen reduction reaction (ORR). The physical properties of the resultant catalysts were characterized using nitrogen adsorption measurements, X‐ray diffraction, Raman and X‐ray photoelectron spectroscopies and transmission electron microscopy. Subsequently, ORR activities of the catalysts were determined electrochemically using a conventional three‐electrode cell via cyclic voltammetry with a rotating disc electrode, the results of which indicated that the synthesized catalysts had a marked electrocatalytic activity towards ORR in acid media. Among the synthesized catalysts, that functionalized using 2,4,6‐tris(2‐pyridyl)‐1,3,5‐triazine as nitrogen source had the highest electrocatalytic activity with the highest onset potential (0.98 V/SHE) and limiting current density (5.12 mA cm⁻²). The findings are particularly important to determine a non‐precious metal catalyst for ORR activity in fuel cells.     

Thermodynamic guidelines for the design of bimetallic catalysts for oxygen electroreduction and rapid screening by scanning electrochemical microscopy. M-co (M: Pd, Ag, Au)

We propose guidelines for the design of improved bimetallic (and related) electrocatalysts for the oxygen reduction reaction (ORR) in acidic media. This guide is based on simple thermodynamic principles assuming a simple mechanism where one metal breaks the oxygen-oxygen bond of molecular O(2) and the other metal acts to reduce the resulting adsorbed atomic oxygen. Analysis of the Gibbs free energies of these two reactions guides the selection of combinations of metals that can produce alloy surfaces with enhanced activity for the ORR when compared to the constituent metals. Selected systems have been tested by fabricating arrays of metallic catalysts consisting of various binary and ternary combinations of Pd, Au, Ag, and Co deposited on glassy carbon (GC) substrates. The electrocatalytic activity of these materials for the ORR in acidic medium was examined using scanning electrochemical microscopy (SECM) in a new rapid-imaging mode. This was used to rapidly screen arrays covering a wide range of catalyst compositions for their activity for the ORR in 0.5 M H(2)SO(4). Using the SECM technique, we have identified combinations of metals with enhanced electrocatalytic activities when compared with the constituent, pure metals. Addition of Co to Pd, Au, and Ag clearly decreases the ORR overpotential, in agreement with the proposed model. Catalyst spots that exhibited enhanced electrocatalytic activity in the SECM screening technique were then examined using classical rotating disk electrode (RDE) experiments. The activity of carbon black supported catalyst mixtures on a GC RDE and the electrocatalytic activity determined using the SECM screening technique showed excellent agreement. C/Pd-Co electrodes (10-30% Co) exhibited remarkable activity for ORR catalysis, close to that of carbon-supported Pt.     

质子交换膜燃料电池Pd修饰Pt/C催化剂的电催化性能

通过对Pt催化剂表面进行Pd修饰提高质子交换膜燃料电池阴极催化剂的氧还原反应(ORR)活性. 采用乙二醇还原法制备了不同比例的Pd修饰Pt/C催化剂. 透射电镜(TEM)和X射线衍射(XRD)测试结果表明, 制备的催化剂贵金属颗粒粒径主要分布在1.75～2.50 nm之间, 并均匀地分散在碳载体表面. 循环伏安方法(CV)研究表明Pd修饰Pt/C催化剂的电化学活性面积低于传统的Pt/C催化剂. 但通过旋转圆盘电极(RDE)测试研究发现, 制备的催化剂具有比传统Pt/C催化剂高的ORR活性.     

制备条件对甲醇电氧化催化剂PtRu/CAs性能的影响

本文利用液相浸渍还原的方法制备了PtRu/C催化剂, 其中Pt质量百分含量分别为15%, Pt和Ru的原子比为2:1. 研究了金属前驱体于不同介质（CH3COOH、H2O及CH3COONa）中浸渍所制备的催化剂组成, 结构以及活性方面的区别. 同时比较分析了不同载体（碳纳米管CNTs与碳气凝胶CAs）对催化剂性能的影响. 催化剂的物化性质通过XRD, TEM以及EDS来表征, 并采用循环伏安法测试其电化学性能. 结果表明以碳气凝胶为载体,均匀分散于异丙醇与水混合溶液后, 加入CH3COOH, 使金属前驱体在酸性介质中浸渍, 再用NaOH调节pH值至碱性, 同时生成CH3COONa作为稳定剂, 然后再用NaBH4还原所制得的催化剂具有更高的电催化活性, 其峰电流密度达到38.24 mA/cm2, 远高于本文中在其他条件下制备的催化剂.     

Formation of a supported cobalt catalyst for the synthesis of carbon nanofibers on aluminum oxide

Comparative studies of the effect of the physicochemical characteristics of a support (aluminum oxide) on the formation of a supported Co catalyst and its activity in the pyrolysis of alkanes (propane-butane) were performed. The effect of the crystalline modification of alumina on the yield of catalytic filamentous carbon (CFC) ((g CFC)/(g Co)) was studied. The surface morphologies of Co-containing catalysts and synthesized carbon deposits were studied by scanning electron microscopy. It was found that carbon deposits with a well-defined nanofiber structure were synthesized by the pyrolysis of a propane-butane mixture in the presence of hydrogen at 600°C on supported Co catalysts prepared by homogeneous precipitation on macroporous corundum (α-Al₂O₃). The yield of CFC was no higher than 4 (g CFC)/(g Co). On the Co catalyst prepared by homogeneous precipitation on mesoporous Al₂O₃, the intense carbonization of the initial support; the formation of cobalt aluminates; and, as a consequence, the deactivation of Co⁰ as a catalyst of FC synthesis occurred. The dependence of the yield of CFC on the preheating temperature (from 200 to 800°C) of Co catalysts before pyrolysis was studied. It was found that, as the preheating temperature of supported Co/Al₂O₃ catalysts was increased, the amount of synthesized carbon, including CFC, decreased because of Co⁰ deactivation due to the interaction with the support and coke formation.     

碳载PdPb催化剂的制备及对甲酸氧化的电催化性能

采用液相还原共沉积法制备出高活性纳米电催化剂PdPb/C, 研究发现, 碳载Pd催化剂中加入Pb能够提高催化剂对甲酸的电氧化活性, 并改变甲酸氧化的反应机理. 少量Pb的加入能够提高催化剂中活性粒子的分散度, 且大幅度提高催化剂对甲酸氧化的电催化活性. 当催化剂中Pd与Pb的质量比为8: 1时, 对甲酸的电氧化活性最高, 峰电流密度约为Pd/C催化剂上的180%; 而当Pd与Pb的质量比为2: 1时, 催化剂对甲酸氧化的稳定性最好.     

Facile Synthesis of AuPd Nanochain Networks on Carbon Supports and Their Application as Electrocatalysts for Oxygen Reduction Reaction

The present work reports the facile synthesis and characterization of carbon‐supported porous Pd shell coated Au nanochain networks (AuPdNNs/C). By using Co nanoframes as sacrificial templates, AuPdNNs/C series have been prepared by a two‐step galvanic replacement reaction (GRR) technique. In the first step, the Au metal precursor, HAuCl₄, reacts spontaneously with the formed Co nanoframes through the GRR, resulting in Au nanochain networks (AuNNs). The second GRR is performed with various concentrations of Pd precursor (0.1, 1, and 10 mM PdCl₂), resulting in AuPdNNs/C. The synthesized AuPdNNs/C series are investigated as electrocatalysts for oxygen reduction reaction (ORR) in alkaline solution. The physical properties of the AuPdNNs/C catalysts are characterized by scanning electron microscopy (SEM), high‐resolution transmission electron microscopy (HRTEM), UV‐vis absorption spectroscopy, and cyclic voltammetry (CV). Rotating disk electrode (RDE) voltammetric studies show that the Au_0.8Pd_0.2NNs/C (prepared using 1 mM PdCl₂) has the highest ORR activity among all the AuPdNNs/C series, which is comparable to commercial Pt catalyst (E‐TEK). The ORR activity of AuPdNNs/C is presumably due to the enhanced Pd surface area and high porosity of Pd nanoshells.     

N,S-Co-Doped Porous Carbon Nanofiber Films Derived from Fullerenes (C60) as Efficient Electrocatalysts for Oxygen Reduction and a Zn–Air Battery

The development of highly efficient metal-free electrocatalysts for the oxygen reduction reaction (ORR) has attracted great attention for the creation of electrochemical energy devices. In this study, one-dimensional (1 D) fullerene nanofibers prepared from liquid–liquid interfacial precipitation are first fabricated into fullerene-derived carbon nanofiber films (FCNFs) through a simple filtration procedure. Then, pyrolysis of the FCNFs in the presence of ammonia and sulfur produces N- and S-co-doped porous carbon nanofiber films (N,S-PCNFs). As excellent metal-free electrocatalysts for the ORR, N,S-PCNFs exhibit remarkable catalytic activity, superior stability, and excellent methanol tolerance in both alkaline and acidic solution. Such a high ORR performance benefits from the robust porous nanofiber network structure with high concentrations of active N- and S- groups and abundant defects. Notably, upon practical use of N,S-PCNFs as catalysts in Zn-air batteries, a high power density and a large operating voltage are achieved, with a performance comparable to that of the commercial Pt/C catalyst. This work presents a facile strategy for the creation of a new class of energy nanomaterials based on fullerenes, demonstrating their practical uses in electrocatalytic ORR processes and Zn-air batteries.     

Oxygen reduction reaction on carbon-supported palladium nanocubes in alkaline media

Carbon-supported Pd nanocubes with the size of 30, 10 and 7 nm were prepared and their electrocatalytic activity towards the oxygen reduction reaction (ORR) in alkaline solution was studied. For comparison carbon-supported spherical Pd nanoparticles and commercial Pd/C catalyst were used. The catalysts were characterised by transmission electron microscopy, electro-oxidation of carbon monoxide and cyclic voltammetry and the ORR activity was evaluated using the rotating disk electrode method. The ORR on all studied Pd/C catalysts proceeded via four-electron pathway where the rate-limiting step was the transfer of the first electron to O₂ molecule. The specific activity of Pd nanocubes was more than two times higher than that of spherical Pd nanoparticles and increased with increasing the particle size.     

大孔碳载Ir催化剂对氨氧化的电催化性能

分别以大孔炭(MC)和Vulcan XC-72炭黑(XC)为载体,制备了Ir/MC和Ir/XC催化剂。 在用X射线能量色散谱(EDS)、X射线衍射(XRD)谱、拉曼光谱对催化剂表征的基础上,用电化学技术研究了2种炭载Ir催化剂对氨氧化的电催化性能,发现氨在Ir/MC催化剂电极上,氧化峰峰电流密度比在Ir/XC催化剂电极上大38.7%左右,而且电催化稳定性明显好于Ir/XC催化剂。 由于Ir/MC和Ir/XC催化剂的Ir粒子平均粒径和相对结晶度相似,因此,这只能归结于MC有大的孔径和孔率及高的石墨化程度引起的高电导率。 所以MC是一种比XC更好的催化剂的炭载体。