甲基异丁酮碘萃合物-水界面上的循环伏安法间接测定水溶液中氧化性金属离子

利用甲基异丁酮(MIBK)作为萃取剂,等体积法将水中的碘萃取到有机相中,微量进样器将20～40μL有机溶液注入玻璃微管中,使它处于界面上。利用经典的三电极系统研究该有机相在液/液界面的伏安特性。实验结果表明,该过程是一个受扩散控制的不可逆过程。有机相中碘的含量和峰电流大小在一定范围内成正比。利用这一特性可以间接测定水溶液中具有氧化性的金属离子(如Cr2O72-、Cu2 等)的含量,检出限为10-5mol/L。     

液/液界面萃取循环伏安法测定Pb2+离子研究

本文利用吡咯烷二硫代氨基甲酸铵（APDC）作为螯合剂,甲基异丁酮（MIBK）作为萃取剂,将水相中的Pb2+萃取到有机相中,利用经典的三电极系统研究该有机相在液/液界面的伏安特性。实验结果表明,该电化学过程是一个由扩散控制的不可逆过程,Pb2+的萃取物从有机相转移到水相。铅萃取物的转移峰在0.16V vs.SCE处,并且在1.0×10-5~ 9.0×10-5mol/L范围内与峰电流大小成正比。这一方法为工业废水中铅的在线、现场测定提供了可靠、灵敏的监测方法。     

小分子亲水有机溶剂液-液萃取技术在分析化学中的应用进展

介绍了小分子亲水有机溶剂液-液萃取技术的基本原理、影响因素并对小分子亲水有机溶剂液-液萃取技术的发展前景进行了展望,引用文献20篇.     

液/液界面萃取循环伏安法测定Pb2+离子

利用吡咯烷二硫代氨基甲酸铵作为螯合剂,甲基异丁酮作为萃取剂,将水相中的Pb2+萃取到有机相中,利用经典的三电极系统研究该有机相在液/液界面的伏安特性.实验结果表明,该电化学过程是一个不可逆过程,Pbα的萃取物从有机相转移到水相.铅萃取物的转移峰在0.16 V vs.SCE处,并且在1.0×10-5～9.0×10-5mol/L范围内与峰电流大小成正比.这一方法为工业废水中铅的在线、现场测定提供了可靠、灵敏的监测方法.     

三相电极法及其在液/液界面铬(Ⅵ)离子转移研究中的应用

将含有氧化还原探针的硝基苯溶液滴到边平面热解石墨(EPPG)电极上,然后将该电极插入到电解质水溶液中,从而使硝基苯、石墨表面以及水溶液形成一个三相接界线,即形成了EPPG三相电极。利用循环伏安法对EPPG三相电极法的原理进行了研究,得到了比文献报道更理想的液/液界面离子转移热力学数据。本研究还观察到铬(Ⅵ)离子在水相/硝基苯相界面上的转移反应,并测定了铬(Ⅵ)的离子转移热力学数据;同时还分别利用方波伏安法和傅里叶变换-方波伏安法结合"准可逆最大"现象对铬(Ⅵ)在水相/硝基苯相界面上的离子转移动力学进行了比较研究。     

新配体4,6-二甲基-2-嘧啶硫乙酸的合成、电化学性质及离子识别性能研究

合成了一个新配体4,6-二甲基-2-嘧啶硫乙酸(Hdmpytaa)。用循环伏安法(CV)和差示脉冲伏安法(DPV)研究了4,6-二甲基-2-嘧啶硫乙酸的电化学行为。结果表明:该化合物在玻碳电极表面存在吸附特性,在0.1 mol/L四丁基高氯酸铵(TBAP)的N,N-二甲基甲酰胺底液中于-0.83 V(vs.SCE)处有一灵敏的还原峰,其电极反应过程是单电子转移,传递系数α为0.74。利用循环伏安法还研究了该化合物对过渡金属离子的识别作用,发现该化合物在一定浓度下对Cu2 和Pb2 有较好的选择识别性。     

羟基新戊醛在PbO2-SPE组合电极上的电氧化研究

采用热压-电镀法制得PbO₂-固体高聚物电解质(SPE)组合电极. 通过伏安曲线和槽压与过电位曲线的测量, 研究羟基新戊醛在该组合电极上电氧化行为. 通过PbO₂-SPE组合电极在阳极液中有、 无液相支持电解质及不同阴极液情况下的循环伏安曲线和线性伏安曲线比较, 证明该组合电极对羟基新戊醛氧化有较好的电催化作用.     

磷酸三丁酯、4-甲基-2戊酮对铝锂溶液中锂的萃取行为

以磷酸三丁酯(TBP)作为主要萃取剂,4-甲基2-戊酮(MIBK)作为协助萃取剂,三氯化铁(FeCl₃)作为共萃剂,以铝锂溶液体系作为试验对象,全面系统的研究了萃取剂的各组成成分、水相溶液的pH值、铁锂原子比、萃取相比、萃取时间以及静置时间对铝锂溶液中锂的萃取效果的影响。通过正交试验确定了萃取反应的最佳反应参数：萃取相比为5∶2,铁锂原子比为2∶1,pH值为1.5,TBP体积分数为70%,MIBK体积分数为15%,萃取时间为10 min。在此条件下,锂的单级萃取率可达82%,锂铝单级分离因数可达51。对萃取分离过程的反应机理进行了研究,深入探索了铁锂共萃取效应,确定了反应产生的萃合物形态为LiFeCl₄·2TBP·MIBK,并探究了萃合物形成过程中的键合方式。该萃取方法经济高效,适用于铝锂溶液中锂的分离。     

液-液-液微萃取-高效液相色谱法测定人尿液中的美沙酮

建立了液-液-液微萃取与高效液相色谱联用技术快速分析尿样中美沙酮的方法.对有机溶剂种类、体积、样品溶液的pH值、萃取时间、搅拌速度进行了优化.方法的线性范围为0.05～10 mg/L,检出限为0.025 mg/L,相对标准偏差小于5%.     

利用自制的汞离子选择电极测定香烟中汞(Ⅱ)

1 引言 汞及其部分化合物属于剧毒物质,并可在人体内累积引发汞中毒.因此,对汞含量的测定方法研究一直是人们关注的一个重要课题,其含量的测定方法一般采用原子吸收法、动力学分光光度法、流动注射光度法、溶出伏安法、液膜汞离子选择电极法等.本文报道了以氯曲米通(N,N-二甲基-γ-(4-氯苯基)-2-吡啶丙胺顺丁稀二酸盐)与碘汞酸盐缔合物为电活性物,制备了PVC膜汞*"选择电极,并用该电极对香烟中汞含量进行了测定,结果令人满意.     

Development of determination method of trace nickel in natural water by ID-oxygen added nitrogen-MIP-MS with direct measurement of liquid–liquid extracted organic phase

This work introduces the development of a novel determination method of trace nickel (ng l^–1 level) in natural water samples. Nickel in the water samples is liquid–liquid extracted into methyl isobutyl ketone (MIBK) as nickel-diethyldithiocarbamate (DDTC) complex, and isotope dilution-oxygen added nitrogen-microwave induced plasma mass spectrometry (ID-oxygen added nitrogen-MIP-MS) is conducted by direct measurement of the liquid–liquid extracted organic MIBK phase. The accuracy of the proposed method was confirmed by analysing certified reference materials (NRC NASS-5 seawater, NRC SLRS-3 riverine water and NRC SLRS-4 river water), and the analytical results obtained were in good agreement with the certified values. The detection limit for nickel is 1.3?ng?l^?1 when the water sample is 50 times concentrated. The precision as RSD is <4%. The proposed method was applied to clarify the concentration-depth vertical profiles of nickel in Lake Mashu, Japan, as the Baseline Station of the United Nations GEMS/Water (Global Environment Monitoring System/Water) Programme.     

Influence of the solvent on the extraction of copper(II) from nitrate medium using salicylideneaniline

Different solvents including cyclohexane, dichloromethane, chloroform, toluene, 1-octanol, and methyl isobutyl ketone (MIBK) have been evaluated in extracting copper(II) from nitrate medium by salicylideneaniline. Extracted species differs from solvent to solvent: CuL₂ in cyclohexane, toluene, 1-octanol, and methyl isobutyl ketone. However, in dichloromethane or chloroform, there are two complexes of the type CuL₂ and CuL₂(HL). The extraction constants and percentage of extraction (%E) are calculated for different solvents. Solvent played an important role in recovering copper(II) from the aqueous solution, thus affecting the extraction equilibrium and extraction efficiency. The nonpolar solvent showed better performance than the polar solvent. The maximum extraction efficiency was 85.75% at pH?=?4.5, which was from cyclohexane.     

一种用于鸡蛋中氯霉素残留测定的吡啶类离子液体双水相体系

建立了由亲水性离子液体N-乙基吡啶溴化盐([Epy]Br)和K2HPO4形成的双水相体系对鸡蛋中痕量氯霉素(CAP)检测的高效液相色谱方法.优化了离子液体[Epy]Br和K2HPO4成相的条件,研究了萃取CAP的最佳体系.采用混合溶液(pH=7磷酸盐溶液,NaCl溶液,甲醇)提取样品,离子液体双水相体系富集,V(甲醇):V(水)=30:70为流动相,流速1.0 mL/min,UV检测器,检测波长278 nm,柱温25 ℃,进样量20 μL.对鸡蛋中氯霉素残留进行了测定,在0.05～15 mg/L范围内,CAP的响应峰面积与其相应浓度呈良好相关性(r=0.9994).不同浓度的回收率为90.3%～101.7%,相对标准偏差为1.7%～2.6%.本该法检测鸡蛋中氯霉素残留具有干扰小、速度快、灵敏度高等优点.最低检出限为1 μg/kg.     

Solvent‐vapor‐assisted liquid–liquid microextraction: A novel method for the determination of phthalate esters in aqueous samples using GC–MS

A novel liquid–liquid microextraction method, namely, solvent‐vapor‐assisted liquid–liquid microextraction for the determination of dimethyl phthalate, diethyl phthalate, dibutyl phthalate and bis(2‐ethylhexyl) phthalate in the aqueous samples using gas chromatography with mass spectrometry was developed. In the proposed method, extracting solvent was heated, and solvent vapor as the extracting phase was injected into the sample solution. As a result of the low temperature of the sample solution and higher density of the extracting phase than the aqueous medium, solvent vapor was condensed and an organic‐phase drop formed in the bottom of sample tube. Because of the gas status of the extracting solvent, the surface area between the extracting solvent and the aqueous sample was remarkably high. Under the optimized conditions, tetrachloride carbon was used as an extracting solvent. The method shows high coefficient of determination (R ²) values in the range of 0.5–200 and 1.0–200 ng/mL for the target analytes. Enrichment factors and limits of detection for the studied phthalates are obtained in the ranges of 2800–3000 and 0.15–0.3 ng/mL, respectively. Recoveries and relative standard deviations were in the range of 80.0–100.0 and 2.2–7.8%, respectively. The proposed method successfully used for analysis of several aqueous samples.     

A green procedure for the protection of carbonyl compounds catalyzed by iodine in ionic liquid

Aldehydes and ketones are protected with ethylene glycol in the presence of a catalytic amount of iodine in PEG ionic liquid (IL 400) under mild conditions to afford the corresponding ketals in good yields. The recovery of iodine is facilitated by the ionic liquid. The recovered catalyst was reused six times with consistent activity.     

Direct determination of several elements in MIBK extract by high-power nitrogen-oxygen mixed gas microwave-induced plasma optical emission spectrometry

A nitrogen-oxygen mixed gas microwave-induced plasma with an Okamoto cavity was employed as an atomization and excitation source for emission spectrometric analysis of organic solvent samples. Nitrogen–oxygen mixed gas produces very a stable microwave-induced plasma that is highly robust to the loading of 4-methyl-2-pentanone (MIBK), possibly because the organic solvent is completely combusted in the oxygen-containing plasma. After extracting test solutions containing Al, Co, Cr(III), Cu, Fe(III), Mo(VI), Ni, Pb with MIBK, both the aqueous phase and the organic phase were aspirated into the microwave-induced plasma, yielding linear calibration curves for both the species in the aqueous phase (Al, Co, Cr, Ni, and Pb) and those in the organic phase (Fe and Mo). These results indicate that Fe and Mo can be extracted with MIBK, which is explained by the partition coefficients of these elements in MIBK.     

Solvent extraction study of protactinium(V) with methyl-iso-butyl carbinol and methyl-iso-butyl ketone

In order to study the extraction pattern of protactinium in different types of extracting agents and compare the similarity of patterns of extraction with dubnium and thereby unraveling its chemistry, solvent extraction of protactinium(V) with methyl-iso-butyl carbinol (MIBC) and methyl-iso-butyl ketone (MIBK) was studied using ²³³Pa as a radiotracer. The extraction efficiencies of Pa were determined as a function of shaking time, concentrations of mineral acids, and extractant concentrations using the two extractants. The results show that MIBK is more suitable for the extraction of protactinium than MIBC in benzene. Furthermore, the effect of the F anion is also discussed. The text was submitted by the authors in English.     

Equilibrium and kinetics of Zn(II) bromide extraction with Amberlite LA-2 and methyl isobutyl ketone

The rates of extraction of Zn(II) from hydrobromic acid solutions into benzene solutions of the liquid anion exchanger Amberlite LA-2 and those into methyl isobutyl ketone (MIBK) have been investigated. The distribution equilibria of this system have been also studied. Under the used experimental conditions the extracted species of Zn(II) have been proposed. The kinetic data indicated a first order reaction with respect to Zn(II) in both systems, nearly one with respect to HBr and from 0–0.38 for LA-2. In case of extraction of Zn(II) with methyl isobutyl ketone, MIBK, the reaction order with respect to MIBK was found to be 4 and with respect to HBr inverse first order. The rate constants of these extraction processes were determined and the rate determining steps were discussed in the light of the obtained results.     

Comparison of three different dispersive liquid–liquid microextraction modes performed on their most usual configurations for the extraction of phenolic,neutral aromatic,and amino compounds from waters

In this work we seek clues to select the appropriate dispersive liquid–liquid microextraction mode for extracting three categories of compounds. For this purpose, three common dispersive liquid–liquid microextraction modes were compared under optimized conditions. Traditional dispersive liquid–liquid microextraction, in situ ionic liquid dispersive liquid–liquid microextraction, and conventional ionic liquid dispersive liquid–liquid microextraction using chloroform, 1‐butyl‐3‐methylimidazolium tetrafluoroborate, and 1‐hexyl‐3‐methylimidazolium hexafluorophosphate as the extraction solvent, respectively, were considered in this work. Phenolic, neutral aromatic, and amino compounds (each category included six members) were studied as analytes. The analytes in the extracts were determined by high‐performance liquid chromatography with UV detection. For the analytes with polar functionalities, the in situ ionic liquid dispersive liquid–liquid microextraction mode mostly led to better results. In contrast, for neutral hydrocarbons without polar functionalities, traditional dispersive liquid–liquid microextraction using chloroform produced better results. In this case, where dispersion forces were the dominant interactions in the extraction, the refractive index of solvent and analyte predicted the extraction performance better than the octanol/water partition coefficient. It was also revealed that none of the methods were successful in extracting hydrophilic analytes (compounds with the log octanol/water partition coefficient <2). The results of this study could be helpful in selecting a dispersive liquid–liquid microextraction mode for the extraction of various groups of compounds.