对-RTlnKco=ΔrGmo(T,co)的理论探讨

应用热力学特性函数、齐次函数定理和勒让德变换等概念和方法从理论上探讨了热力学公式RTlnKco=ΔrGmo（T,co）在推导和应用方面的问题。严格的数学论证表明该式是背离热力学原理的,它近似地适用于液相,但应用于气相则可能产生较大偏差。     

LixNi0.8-yCo0.2ZnyOp的合成及电化学性能研究

A series of single-phase Li_xNi_0.8-yCo_0.2Zn_yO_p(0.96 ≤x≤ 1.10， 0 ≤y≤ 0.05， 2 ≤p≤ 2(1+y) ) (different in the y values) were synthesized by a two-step solid state reaction method， in which LiOH·H₂O， Zn-doped spherical Ni(OH)₂ and Co₂O₃ were used as the precursors. The ICP-AES analyses proved that the Zn-doped compounds synthesized had the nonstoichiometric form. The results of the XRD， SEM identified that the uniform particles of the as-prepared materials having a good layered structure were fine， narrowly distributed and well crystallized. The electrochemical performance test was carried out and the results showed that the as-prepared Zn-doped materials had not only a high capacity， but also a better cycling stability characterization than the un-doped one. The Li_1.06Ni_0.75Co_0.22Zn_0.03O_2.03 material has an initial reversible capacity as high as 160.5mAh·g^-1; and a first discharge efficiency 89.2%， and exhibits satisfactory cyclic stability with 90% retainable capacity after 50 cycles.     

Zr1-xMxWMoO8-x/2和Zr1-xMxW2O8-x/2固溶体的晶胞参数与晶格畸变的关系

合成了Zr1-xMxWMoO8-x/2(M=Er,Tm,Yb,Sc,In,Ga,Al)和Zr1-xMxW2O8-x/2(M=Eu,Er,Yb,Sc,In,Ga,Al)2个系列的固溶体,前者具有β-ZrW2O8结构类型(简称β相);后者具有α-ZrW2O8结构类型(简称α相)。建立了相和相的晶胞参数与M3+离子浓度的Vegard方程,测定了上述固溶体的固溶度。讨论了M3+离子的化学性质与Vegard斜率SV的关系。分析了α相的SαA与β相的SβA的关系;揭示了α-Zr1-xMxW2O8-x/2晶格中2[WO4]四面体对的取向有序程度对晶格畸变的贡献。提出上述固溶体的晶胞参数随溶质浓度增加而减小,主要是由于氧空位缺陷相互作用的结果。     

钙钛矿型LaxSr1－xNi1－yCoyO3光电催化活性研究

用甘氨酸-硝酸盐燃烧合成法, 制备La_xSr_1－xNi_1－yCo_yO₃复合氧化物的陶瓷粉末, 对钙钛矿氧化物进行了XRD结构分析. 在通氧或不通氧下测试氧还原和氧析出的循环伏安曲线. 结果表明: 该氧电极具有双功能催化特性, 但不完全可逆. 利用汞灯作为激发光源, 进行几种水溶性染料和五种混合染料光解实验, 利用紫外-可见、红外以及人工神经网络光度法研究La_xSr_1－xNi_1－yCo_yO₃的催化性能. 结果表明: La_xSr_1－xNi_1－yCo_yO₃ (x＝0.7, 0.9, 1; y＝0.3, 0.75)复合氧化物都具有较强光催化特性; La_xSr_1－xNi_1－yCo_yO₃的光催化活性高于La_xSr_1－xNiO₃, 这与B位离子(Ni^2—, Co^2－)的电子构型有关; Co^2＋的加入可使La_xSr_1－xNiO₃的光催化活性有所提高.     

Af-AaDd型氢键体系的网络结构参数

利用溶胶-凝胶分配理论对氢键溶液的模型体系进行研究, 给出了凝胶点后氢键网络中各结构参数的计算方案, 并进行相应的数值计算. 结果表明, 因受体基团本身的性质及两类质子受体基团的数量比不同, 受体基团的竞争作用对网络结构有明显影响, 这提供了控制氢键网络结构特征的可能方法.     

LixZryOz三元化合物的制备及表征

采用高温固相法制备了4种高纯度晶相组成的LixZryOz三元化合物,研究了焙烧温度、时间、反应物的种类和初始反应物物质的量比对产物组成的影响,进一步用XRD、SEM及BET分析方法对产物的晶相结构、表面形貌及比表面积进行了表征.实验结果表明,Li2CO3与ZrO2在适当条件下可以合成得到单斜相Li3ZrO3;以LiOH替代Li2CO3,在适当条件下可以分别合成得到四方相Li2ZrO3和三斜/单斜相Li6Zr2O7;进一步以Zr(NO3)4·5H2O代替Zr02,可将单斜相Li6Zr2O7的制备时间由96 h缩短至24 h.SEM照片显示产物硬团聚明显,粒径分布在1～10μm间,BET分析表明样品比表面积处于1.0～9.0 m2·g-1间分布,反应过程中锂的过量以及长时间高温焙烧是引起产物粒径长大和产生硬团聚的主要原因.     

nFe3+/nSr2+和nOH-/nNO3-对锶铁氧体纳米片结构及磁性能的影响

采用改进的水热法成功合成了单分散的纯相锶铁氧体纳米片。借助DLS、XRD、FTIR、SEM、EDS和VSM等分析测试手段对SrFe₁₂O₁₉铁氧体粉体的粒度、结构、形貌和磁性能进行表征。研究结果表明,在240℃保温5 h,物质的量之比n_Fe³⁺/n_Sr²⁺(R_F/S)和n_OH^-/n_NO^-(R_O/N)分别为5和2时,所得产物为单分散的纯相六角SrFe₁₂O₁₉铁氧体纳米片。随着R_F/S和R_O/N的变化,合成样品中有少量SrCO₃和Fe₂O₃杂相存在,这主要与反应条件和离子比例有关。磁性能测试结果显示,所得纯相的六角SrF₁₂O₁₉铁氧体纳米片具有优异的磁性能,其饱和磁化强度和矫顽力分别达到60.91 emu·g^-1和94.83 kA·m^-1,使其在医疗、催化和生物等高技术领域具有潜在的应用。     

nFe3+/nSr2+和nOH-/nNO3-对锶铁氧体纳米片结构及磁性能的影响

采用改进的水热法成功合成了单分散的纯相锶铁氧体纳米片。借助DLS、XRD、FTIR、SEM、EDS和VSM等分析测试手段对SrFe₁₂O₁₉铁氧体粉体的粒度、结构、形貌和磁性能进行表征。研究结果表明,在240℃保温5 h,物质的量之比n_Fe³⁺/n_Sr²⁺(R_F/S)和n_OH^-/n_NO3^-(R_O/N)分别为5和2时,所得产物为单分散的纯相六角SrFe₁₂O₁₉铁氧体纳米片。随着R_F/S和R_O/N的变化,合成样品中有少量SrCO₃和Fe₂O₃杂相存在,这主要与反应条件和离子比例有关。磁性能测试结果显示,所得纯相的六角SrF₁₂O₁₉铁氧体纳米片具有优异的磁性能,其饱和磁化强度和矫顽力分别达到60.91 emu·g^-1和94.83 kA·m^-1,使其在医疗、催化和生物等高技术领域具有潜在的应用。     

纳米钙钛矿LaxSr1-xFe1-yCoyO3复合氧化物的制备和表征

用甘氨酸-硝酸盐燃烧合成法，制备La_xSr_1-xFe_1-yCo_yO₃复合氧化物的陶瓷粉末，对该钙钛矿型氧化物进行了XRD、IR、紫外漫反射光谱及循环伏安曲线分析。结果表明：该复合氧化物粉体平均晶粒为15.3～29.8 nm,为立方和正交晶系。该氧电极具有双功能催化特性，但不完全可逆。对水溶液染料进行光解实验，利用紫外-可见、人工神经网络光度法研究La_xSr_1-xFe_1-yCo_yO₃的催化性能。结果表明：CO²⁺的加入可使La_xSr_1-xFeO₃的光催化活性有所提高，B位离子(Fe³⁺，CO²⁺)改变与加入，使La_xSr_1-xFe_1-yCo_yO₃(x=0.7，0.3；y=0.3，0.9，1)光催化活性高于La_xSr_1-xFeO₃。同时，对5种染料进行紫外光解，在0.75 h，脱色率大于91%，并为动力学一级反应。     

Solvent extraction separation of In/III/-Tl/III/ and Hg/II/-Cd/II/-Co/II/ with sulphoxides

Solvent extraction studies have been made on some metals: In/III/-Tl/III/ and Hg/II/-Cd/II/-Co/II/, from ammonium thiocyanate solutions by dialkyl sulphoxides. Separation of these metals from one another can be achieved by suitable choice of the extracted conditions. The nature of the extractable metal species has been elucidated.     

Simultaneous propane dehydrogenation andco2hydrogenation overCrOx/SiO2catalyst

Summary Single reverse water-gas shift (RWGS) and dehydrogenation of propane with CO₂(DH-CO₂) reactions in the presence and absence of the CrO_x/SiO₂ catalyst have been studied between 673 and 873 K. It was found that the CrO_x/SiO₂ catalyst is active both in the dehydrogenation of propane and in the RWGS reactions. The obtained results suggest that the dehydrogenation of propane to propene in the presence of CO₂on CrO_x/SiO₂can be facilitated by the RWGS reaction.</o:p>     

Synthesis of chlorobis/β-diketonato/oxotechnetium/V/ and tris/β-diketonato/technetium/III/ complexes

Chlorobis/-diketonato/ oxotechnetium/V/ complexes [TcOCl/-dik/₂, -diketone=acetylacetone, benzoylacetone and dibenzoylmethane] were newly synthesized using macroamount of⁹⁹Tc. These complexes were further separated into geometrical isomers. Furthermore, an improvement of the yields for the syntheses of tris/-dike-tonato/technetium/III/ complexes [Tc/-dik/₃, -diketone=acetylacetone, benzoylacetone and 2-thenoyltrifluoroacetone] was examined using Tc/III/-thiourea complexes as a starting material.     

Direct synthesis of dimethyl carbonate ?from CH3OH AND CO2 by H3PW12O40/CexTi1-xO2 catalyst

Summary Ce_xTi_1-xO₂ and H₃PW₁₂O₄₀/Ce_xTi_1-xO₂ catalysts were prepared using a sol-gel method, and applied to the direct synthesis of dimethyl carbonate from methanol and carbon dioxide. H₃PW₁₂O₄₀/Ce_xTi_1-xO₂ showed a better catalytic performance than the corresponding Ce_xTi_1-xO₂, due to the bifunctional catalysis of Br?nsted acid sites (provided by H₃PW₁₂O₄₀) and base sites (provided by Ce_xTi_1-xO₂). H₃PW₁₂O₄₀/Ce_0.1Ti_0.9O₂ showed the highest catalytic performance among the H₃PW₁₂O₄₀/Ce_xTi_1-xO₂ catalysts.     

Crystal structure of Na3PO4 · 12H2O

The crystal structure of trisodium monophosphate hemihydrate was determined. The space group is $\text{C2}\text{c}$ and a unit cell contains eight formula units. The unit cell dimensions of $\text{Na}{}_3\text{PO}{}_4\text{·}\text{1}\text{2}\text{H}{}_2\text{O}$ are a = 9.631(3), b = 5.416(2), c = 16.938(8) Å, β = 102.60(5)°. The final R value is 0.027 for a set of 1430 independent reflections. This atomic arrangement is mainly a three-dimensional network of distorted NaO₆ octahedra. The hydrogen bonding scheme is given.     

Synthesis and characterization of Ti1−2xNbxNixO2−x/2 solid solutions

Doped-rutile has been traditionally used in ceramic pigments for its intense optical properties. In this paper, we compare the classical ceramic synthesis of Ti_1−2xNb_xNi_xO_2−x/2 system with the sol-gel methodology, which allows a reduction of the anatase-rutile transformation temperature. The composition was optimised in order to obtain a unique rutile phase with the minimum amount of pollutant Ni(II) and enhanced chromatic coordinates. Incorporation of the doping ions in the rutile structure was corroborated by XRD and Rietveld refinements. The species responsible for the colour mechanism were studied by different techniques. UV-VIS spectroscopy showed the characteristic features of Ni²⁺ ions, whose existence was corroborated by EPR and magnetic measurements. From these results, (Ni,Nb)doped-TiO₂ powder samples can be now shaped as thin films, monoliths, etc. by using sol-gel methodology without modifying their properties. This study introduces new possibilities of coloured TiO₂-based solid solutions in new combined advanced applications (colouring agent and photocatalyst, etc.).     

An investigation of the promotional effect of propylene or propane traces on the activity of sulfatedPt/g-Al2O3andPt-Sn/g-Al2O3inCH4combustion

Summary A strong promoting effect of the presence of C₃H₈or C₃H₆was determined for the combustion of CH₄in excess oxygen, over pre-sulfated 1%Pt/g-Al₂O₃and pre-sulfated 1%Pt-2%Sn/g-Al₂O₃catalysts.</o:p>     

Visible light-sensitive yellow TiO2−xNx and Fe-N co-doped Ti1−yFeyO2−xNx anatase photocatalysts

Nitrogen substituted yellow colored anatase TiO_2−xN_x and Fe-N co-doped Ti_1−yFe_yO_2−xN_x have been easily synthesized by novel hydrazine method. White anatase TiO_2−δ and N/Fe-N-doped samples are semiconducting and the presence of ESR signals at g ∼1.994-2.0025 supports the oxygen vacancy and g∼4.3 indicates Fe³⁺ in the lattice. TiO_2−xN_x has higher conductivity than TiO_2−x and Fe/Fe-N-doped anatase and the UV absorption edge of white TiO_2−x extends in the visible region in N, Fe and Fe-N co-doped TiO₂, which show, respectively, two band gaps at ∼3.25/2.63, ∼3.31/2.44 and 2.8/2.44 eV. An activation energy of ∼1.8 eV is observed in Arrhenius log resistivity vs. 1/T plots for all samples. All TiO₂ and Fe-doped TiO₂ show low 2-propanol photodegradation activity but have significant NO photodestruction capability, both in UV and visible regions, while standard Degussa P-25 is incapable in destroying NO in the visible region The mid-gap levels that these N and Fe-N-doped TiO₂ consist may cause this discrepancy in their photocatalytic activities.