Development of a tubular fluoride potentiometric detector for flow analysis: evaluation and analytical applications

In this work a construction procedure for tubular fluoride electrode to be used in flow systems is outlined. The electrode was constructed from a commercially available, LaF₃ single crystal. Principal advantages of the flow detector presented include simplicity of construction, robustness, durability, low cost and easy coupling into any point of a flow manifold.Evaluation of the intrinsic working characteristics of the potentiometric detector in a low dispersion manifold is presented with respect to analytical and dynamic parameters. The constructed detector has similar working characteristics to those of the conventional fluoride electrodes, namely the detection limit, lower limit of linear response and operational pH range.The analytical usefulness of the constructed device was assessed in a flow system developed for fluoride determination in toothpaste, tablet, collutory and water samples for which the reference procedures suggest the determination of fluoride ion with a conventional ion selective electrode.     

Development of a potentiometric flow cell with a stainless steel electrode for pH measurements. Determination of acid mixtures using flow injection analysis

In this work a stainless steel electrode was prepared, characterised and used as indicator electrode in a potentiometric flow cell. Due to its versatility, it was possible to study different electrode geometries and flow cell arrangements. After optimising the system, mixtures of succinic and oxalic acids were determined by titration. Partial least squares (PLS) regression as multivariate calibration tool was applied for data treatment. The predicted results obtained in a test set showed a relative error of 4.3% for succinic acid and 5.5% for oxalic acid.     

On-line flow injection solid sample introduction, leaching and potentiometric determination of fluoride in phosphate rock

A flow injection method with on-line solid sample dissolution was developed for the determination of fluoride in phosphate rock. The fluoride was selectively leached (98-102.4 % recovery) from a 50-mg powdered phosphate rock sample with 0.50 M citric acid. Using the zone sampling technique the fluoride in the buffered leachate was determined by injecting 87 μL into the carrier stream using a fluoride ion-selective electrode detector. The sensing element of the electrode was housed in a home-made sleeve-type flow-through cell. On-line solid sample digestion with 0.50 M citric acid at 55 °C resulted in minimum dissolution of interfering iron and aluminum ions with improved accuracy and calibration linearity. The incorporation of relatively high level of fluoride in the carrier stream (40 μg mL⁻¹) facilitated the determination of high levels of fluoride in phosphate rock (up to 4.1%) with out the need for excessive on-line dilution.The optimized flow system was applied for the determination of fluoride in phosphate rocks samples and a reference material at a rate of nine samples per hour with a relative standard deviation (n = 5) of 2.95-4.0 %. Comparison of the proposed flow injection method with the standard method, which involves steam distillation from sulfuric acid solution and manual titration with thorium nitrate, showed no evidence of bias at the 95% confidence level.     

Trace enrichment and determination of silver by immobilized DDTC microcolumn and flow injection atomic absorption spectrometry

Flow injection (FI) system incorporating a microcolumn of immobilized diethyldithiocarbamate (DDTC) on surfactant-coated alumina was combined with atomic absorption spectrometry for on-line trace enrichment and determination of silver in different matrices. Silver was deposited on the microcolumn by processing a standard or solution of analyte at pH 3-4 on the column. Injection of 250 μl of ethanol then served to elute the retained species to atomic absorption spectrometry (AAS). A sample volume of 20 ml resulted in a pre-concentration factor of 125, and precision at the 20 μg l⁻¹ was 4% (R.S.D.). The procedure was applied to tap water, well water, rain water, sea water, radiology film, and lead concentrate samples. The accuracy was assessed through recovery experiments, independent analysis by furnace-AAS, and analysis of certified reference material.     

Microwave-assisted on-line derivatization for sensitive flow injection fluorometric determination of formaldehyde in some foods

A rapid and sensitive flow injection fluorometry has been developed for the determination of formaldehyde based on the microwave on-line accelerating its Hantzsch reaction with cyclohexane-1,3-dione. Under the optimized conditions, the fluorescent intensity is proportional to formaldehyde content in the range from 0.05 ng/mL to 2.000 μg/mL. The detection limit (S/N = 3) is 0.02 ng/mL and the analytical frequency is 28 injections per hour. The relative standard deviations are 2.2% and 3.1% for eleven injections of 0.100 and 0.001 μg/mL of formaldehyde, respectively. With the assistance of microwave irradiation, a best sensitive fluorometry was established for the determination of formaldehyde at a high analytical frequency. This method was successfully applied to food analysis without requiring any sample pretreatment, and the determination results were correlated well with those obtained by the standard method with a sample pretreatment of steam distillation.     

On-line preconcentration and determination of cobalt by chelating microcolumns and flow injection atomic spectrometry

A simple and sensitive flow injection analysis-atomic absorption spectrometric procedure is described for the determination of cobalt. The method is based upon on-line preconcentration of cobalt on a microcolumn of 2-nitroso-1-naphthol immobilized on surfactant coated alumina. The trapped cobalt is then eluted with ethanol (250 μl) and determined by flame atomic absorption spectrometry. The analytical figures of merit for the determination of cobalt are as follows: detection limit (3 S), 0.02 ng ml⁻¹; precision (RSD), 2.8% for 20 ng ml⁻¹ and 1.7% for 70 ng ml⁻¹ of cobalt; enrichment factor, 125 (using 25 ml of sample). The method has been applied to the determination of cobalt in water samples, vitamin B₁₂ and B-complex ampoules and accuracy was assessed through recovery experiment and independent analysis by furnace AAS.     

Reversed flow injection and sandwich sequential injection methods for the spectrophotometric determination of copper(II) with cuprizone

Two new flow methods, flow injection analysis (FIA) and sequential injection analysis (SIA), for the spectrophotometric determination of Cu(II) in water at trace levels have been developed and optimised. Both methods are based on the reaction with oxalic acid bis(cyclohexylidene hydrazide) (cuprizone) in alkaline media. The two procedures have been developed for the final aim to compare their performances and to offer new rapid heavy metals analysis tools, avoiding the use of extraction steps. A detailed study of the physico-chemical parameters affecting the systems performances has been carried out. The reversed FIA and sandwich SIA approaches offered the best sensitivity. In both cases, an extremely good linearity has been obtained within the range 0.06-4 μg ml⁻¹ (correlation coefficient r=0.9999), whereas the observed detection limits were 0.013 and 0.004 μg ml⁻¹, for FIA and SIA, respectively. Furthermore, due to the great similarity of the diffusion zones in the reaction slugs, our approach offers the opportunity to compare the two methods in analogous conditions. This SIA method, besides keeping its typical reagent saving features, offered analytical performances equivalent to those of FIA. To obtain these results, an original “stop-flow like” method was successfully employed in the SIA approach. Both methods were validated by analysis of real water samples, after copper addition, and certified reference samples of fortified and waste waters.     

On-line ion-exchange preconcentration in a flow injection system coupled to capillary electrophoresis for the direct determination of UV absorbing anions

On-line ion-exchange preconcentration, performed in a flow injection analysis system, has been integrated with capillary electrophoresis via a specially designed interface, and a sensitive and selective method for the determination of nitrite, nitrate, bromide and iodide using direct UV absorbance detection has been developed. Fivefold enrichment of these aforementioned anions can be realised. Separation conditions such as carrier electrolyte and concentration of electroosmotic modifier were investigated. Limits of detection were ca. 10 ng ml⁻¹ for nitrite and nitrate in aqueous samples, and the overall relative standard deviation was about 5%.     

Solid-phase iodine as an oxidant in flow injection analysis: determination of ascorbic acid in pharmaceuticals and foods by background correction

A flow injection analysis (FIA)-background correction method comprising two solid-phase reactors and spectrophotometry for determination of ascorbic acid (AsA) is proposed. A polyethylene mini-column filled with solid iodine (30% m/m suspended on silica gel beads), reactor 1, and other column filled only with silica gel, reactor 2, which are then incorporated in a flow system so that solid iodine reagent in reactor 1 is affected as the sample passes through the column. The sample blank is produced by the oxidation of the AsA by iodine to form dehydroascorbic acid, insensitive to ultraviolet at 267 nm. AsA in samples is determined after injected in reactor 2; the difference in two analytical signal observed is related to amount of AsA. The linear range of the system is up to 50 μg ml⁻¹ with a detection limit of 0.08 μg ml⁻¹, R.S.D. of better than 1.0% and sampling frequency of 110 sample h⁻¹. The method is successfully applied to the determination of AsA in pharmaceuticals and foods.     

Simultaneous potentiometric and fluorimetric determination of diclofenac in a sequential injection analysis system

Two independent methods for the determination of diclofenac were simultaneously implemented in an automated analytical system, based on the concept of sequential injection analysis, providing real-time assessment of results quality. The potentiometric detection was carried out with an ion-selective electrode based on a cyclodextrin while for the fluorimetric determination the sample was previously subject to in-line irradiation with UV light. The potentiometric and photochemical-fluorimetric determinations exhibited linear working ranges of 5×10⁻⁶ to 1×10⁻² and 1×10⁻⁶ to 1×10⁻⁴ mol dm⁻³, respectively. Relative standard errors of 0.5% for the potentiometric determination and 0.6% for the photochemical-fluorimetric determination were obtained after 10 consecutive injections of a 5×10⁻⁵ mol dm⁻³ diclofenac standard solution. The sampling rate was about 32 samples h⁻¹. Both methods were applied in the analysis of pharmaceutical formulations. The quality of results obtained was evaluated by comparison to the reference method, with no statistically significant differences for a 95% confidence level.     

Rapid determination of lead extracted by acetic acid from glazed ceramic surfaces by flow injection on-line preconcentration and spectrophotometric detection

A rapid method has been developed for the determination of lead extracted by acetic acid from glazed ceramic surfaces by flow injection analysis without any pretreatment. An aliquot of 4% acetic acid solution, which has been kept in a teacup for 24 h in the dark, is injected into a carrier solution (1 M nitric acid) and passed through a Pb-Spec resin column. After washing the column with an ammonium nitrate solution, the lead adsorbed on the column is eluted with an ammonium oxalate solution and then merged with a 4-(2-pyridylazo)resorcinol (PAR) solution, followed by measurement of the absorbance of the lead-PAR complex at 530 nm. The detection limit, concentration giving a signal equal to three times the standard deviation of the blank signal, is 8 ng ml⁻¹. The relative standard deviation of measurements at the 0.8 μg ml⁻¹ level is 0.35% (n = 5). The sample throughput is 12 per hour.     

Flow injection potentiometric sensor for determination of phenylpropanolamine hydrochloride

A new polymeric membrane electrode has been constructed for the determination of phenylpropanolamine hydrochloride. The electrode was prepared by solubilizing the phenylpropanolamine-phosphomolybdate ion associate into a polyvinyl chloride matrix plasticized by dibutylphthalate as a solvent mediator. The electrode showed near-Nernstian response over the concentration range of 1 × 10^?5–1 × 10^?2 M with low detection limit of 6.3 × 10^?6 M. The electrode displays a good selectivity for phenylpropanolamine with respect to a number of common inorganic and organic species. The electrode was successfully applied to the potentiometric determination of phenylpropanolamine ion in its pure state and its pharmaceutical preparation in batch and flow injection conditions.     

Flow injection analysis methods for determination of diffusion coefficients

Two flow injection analyses (FIA) methods for the determination of diffusion coefficients in a straight single tube FIA system were developed. Based on the analytical solution of the convection-diffusion equation, linear relationships of the logarithmic values of the dispersion coefficient (D) and the half-peak width (W_1/2) with the diffusion coefficient (D_m) were obtained. Experiments were designed to verify these methods. For example, for potassium hexacyanoferrate (III) a D_m value of 0.72 × 10⁵ cm² s⁻¹ was found versus a literature value of 0.76 × 10⁵ cm² s⁻¹ (error, 5%). For potassium hexacyanoferrate (II) a D_m value of 0.67 × 10⁵ cm² s⁻¹ was obtained versus a literature value of 0.63 × 10⁵ cm² s⁻¹ (error, 6%). The diffusion coefficients of some important biomedical compounds, such as dopamine, epinephrine, norepinephrine and ascorbic acid, were then determined. The values of 10⁵ D_m/cm² s⁻¹ are 0.60 ± 0.03, 0.44 ± 0.02, 0.60 ± 0.01 and 0.68 ± 0.06, respectively.     

New flow injection potentiometric graphite coated ion-selective electrode for the determination of VO ions

A new coated ion-selective electrode for the determination of trace vanadyl ions (VO²⁺) by flow injection potentiometry (FIP) with a home-made flow cell has been developed. The PVC-based membrane was coated on a graphite electrode with an effective area of 4.90 mm². The optimum membrane contains 5 wt.% 1,8-diaminonaphtalene as ionophore, 35 wt.% plasticizer 2-nitrophenyl octyl ether, 55 wt.% PVC and 5 wt.% additive potassium tetrakis (p-chlorophenyl) borate. The electrode in flow injection potentiometry resulted in well defined peaks for vanadyl ions with a very high sampling rate (180 injections/h). Linear calibration was obtained from 1.14×10⁻⁷ to 1.14×10⁻¹ M vanadyl ions, with a slope of 28.3±0.3 mV per decade change in vanadyl concentration, and very low detection limit of 1.14×10⁻⁷ M and the electrode can be used for at least 1 months without any considerable change in potential response. Selectivity coefficients for several ions were obtained by the matched potential method with respect VO²⁺ ions. The flow cell is simple to construct and free from memory effect problems over long periods of use. The sensor was used for the recovery of trace VO²⁺ ions from tap water and the determination of VO²⁺ in synthetic sample.     

Simultaneous on-line preconcentration and determination of trace metals in environmental samples using a modified nanometer-sized alumina packed micro-column by flow injection combined with ICP-OES

A novel organic reagent 3-(8-quinolinylazo)-4-hydroxybenzoic acid (QAHBA) was synthesized for chemically modified nanometer-sized alumina, and it was characterized with infrared spectrum and ¹H NMR spectra. By using modified nanometer-sized alumina as micro-column packing material, a new method of flow injection (FI) on-line preconcentration coupled to ICP-OES was developed for simultaneous determination of trace metals (Ag, Pd, Au, Ga, In and Nb) in geological and environmental samples. The effects of pH, sample flow rate, sample volume, elution and interfering ions on the recovery of the analytes have been investigated. Under the optimized operating conditions, the adsorption capacity of the modified nanometer-sized alumina for Ag, Pd, Au, Ga, In and Nb were found to be 5.1, 7.6, 17.7, 15.6, 8.1 and 12.3 mg g⁻¹, respectively. With 4 min preconcentration time and 24 s elution time, the enrichment factor was 10 and the sample frequency was 10 h⁻¹. The detection limits of this method for Ag, Pd, Au, Ga, In and Nb were 0.12, 0.44, 0.27, 0.19, 0.54 and 0.18 μg l⁻¹, respectively, while the R.S.D.s were 1.6, 2.3, 4.5, 1.6, 1.9 and 1.7% (n = 7, c = 50 ng ml⁻¹), respectively. The proposed method has been applied to the determination of these trace metals in geological-certified reference materials and natural water samples with satisfactory results.     

Construction and performance characterization of ion-selective electrodes for potentiometric determination of phenylpropanolamine hydrochloride applying batch and flow injection analysis techniques

New phenylpropanolamine hydrochloride (PPA.Cl)-selective electrodes of the conventional polymer membrane type, based on incorporation of phenylpropanolamine-tetraphenylborate (PPA-TPB) ion-pair or phenylpropanolamine-phosphotungstate (PPA-PT) ion-associate in a poly(vinyl chloride) (PVC) membrane plasticized with dioctylphethalate (DOP) or dibutylphethalate (DBP), have been constructed. The electrodes were fully characterized in terms of the membrane composition, temperature, and pH. The electrodes were applied to the potentiometric determination of PPA.Cl in pure solutions and in pharmaceutical preparations under batch and flow injection conditions. The sensors showed fast, stable, and Nernstian slope over the concentration ranges 1.0×10⁻⁵ to 8.91×10⁻³ M and 10⁻⁵ to 10⁻² M in the case of PPA-TPB applying batch and flow injection analysis (FIA), respectively, and 5.01×10⁻⁶ to 1.25×10⁻³ M and 10⁻⁵ to 10⁻² M in the case of PPA-PT for batch and FIA systems, respectively. The electrodes exhibited good selectivity for PPA.Cl with respect to a large number of inorganic cations, sugars, amino acids, and components other than phenylpropanolamine of the mixed drugs. The effect of temperature on the electrodes was also studied.     

Method for on-line derivatization and separation of aspartic acid enantiomer in pharmaceuticals application by the coupling of flow injection with micellar electrokinetic chromatography

A novel, easy and accurate capillary electrophoresis (CE) coupled with flow injection (FI) method for the separation and determination of aspartic acid (Asp) enantiomers by on-line derivatization had been developed, and it had been applied to the real sample for the first time. The derivatization reagents were o-phthalaldehyde (OPA) and mercaptoethanol (ME), which were obtained easily, the chiral selector was beta-cyclodextrin (beta-CD), the micellar chemical was sodium dodecyl sulfate (SDS), and the modifier was methanol. By on-line derivatization, aspartic acid enantiomers were automatically and reproducibly converted to the ultraviolet (UV)-absorbing diastereoisomer derivates, which were separated by micellar electrokinetic chromatography (MEKC). According to the factors affecting the separation and sensitivity of aspartic acid enantiomer and other amino acids in the real sample, the pH value and concentration of the buffer, the concentration of beta-CD and SDS, the volume percentage of the methanol (v/v) in the buffer, the applied voltage and the conversion time were selected as the investigating variates. Under the investigated separation conditions, D-aspartic acid (D-Asp), L-aspartic acid (L-Asp) and other four amino acids achieved the baseline separation in not only the standard mixture of amino acids but also the real sample (Compound Amino Acid Injection (6AA)). The repeatability (defined as relative standard deviation (RSD), n = 5) was 4.0% and 4.0% with peak area evaluation, and 4.2% and 3.7% with peak height evaluation for D-Asp and L-Asp in the real sample. Recovery at added standard levels of 1.0, 3.0 and 6.0 mM was 92%, 104% and 109%, respectively.     

A comparison of flow injection methods for sulfide determination based on phenothiazine dyes produced from diverse aromatic amines

In the present work a systematic comparison among spectrophotometric flow injection methods for sulfide determination based on phenothiazine dye production from diverse aromatic p-substituted amines were performed. The behavior of N,N-dimethylphenyl-p-diamine (DMPD), N,N-diethylphenyl-p-diamine (DEPD), phenyl-p-diamine (PPD), p-aminophenol (PAP) and other three aromatic amines was investigated and the chemical parameters of proposed flow methods were optimized by applying central composite design. For each evaluated method the concentration of amine, Fe³⁺ and H₂SO₄ was optimized and after the evaluation of reagents addition order the flow parameters were independently ascertained. Analytical signal was strongly diminished in the presence of iodide for flow methods based on the reaction of sulfide with DMPD, PPD or DEPD while fluoride was considered as an important interference for methods based on the reaction with PPD or PAP. The evaluated aromatic amines have permitted sulfide determination in a wide concentration range from 0.05 to 3.0 mg L^− 1 and limits of detection (3σ) varying from 18.8 to 51.0 μg L^− 1, for DEPD and PPD, respectively. The sensitivity of flow methods based on PPD and DMPD was higher even as PAP has permitted sulfide determination in a large sulfide concentration range. In addition, higher throughput was attained for DMPD method. The proposed methods were applied for sulfide determination in industrial wastewater and the obtained results were in agreement with reference method at 95% confidence level.     

Automatic determination of phylloquinone in vegetables and fruits using on-line photochemical reduction and fluorescence detection via solid phase extraction and flow injection

A very simple, rapid and highly sensitive flow injection fluorimetric method was developed for the determination of phylloquinone. The assay was based on the on-line reduction of phylloquinone in dodecylsulfate micelles after irradiation with UV light. The micellar medium enhanced the fluorescence and stability of the reduced phylloquinone. Under optimum experimental conditions, the range of application of the technique was between 0.09 and 45.0 μg mL⁻¹ and the detection limit was 0.05 μg mL⁻¹. The sample throughput was 90 injections per hour. The reliability of the method for the routine analysis of phylloquinone in vegetables and fruits is demonstrated. Extractions were made with hexane, and an automated solid phase extraction system was used to purify the sample extracts prior to injection into the flow injection manifold.     

A potential high-throughput method for the determination of lipase activity by potentiometric flow injection titrations

Potentiometric FIA titrations were performed to determine enzyme activities of lipase type B from Candida antarctica, CAL-B. Two substrates, triacetin and tributyrin were hydrolyzed in phosphate buffer solutions, and the concentration change of the base component of the buffer was titrated in a carrier solution containing hydrochloric acid and potassium chloride. The system was calibrated with butyric acid and acetic acid, respectively. FIA titration peaks were evaluated with respect to peak height and peak area. Butyric acid and acetic acid could be titrated in the buffer solution from 3 × 10⁻³ mol L⁻¹ to 0.1 mol L⁻¹. The detection limit of enzyme activity was determined to be 0.07 U mL⁻¹ (15 min reaction time) and the minimum activity was calculated to be 0.035 units corresponding to 35 nmol min⁻¹. The specific activities of lipase B for the hydrolysis of tributyrin and triacetin were determined as 16 ± 2 U mg⁻¹ and 2 ± 0.2 U mg⁻¹ (per mg commercial lipase preparation), respectively.