ACF-SPME检测海洋水体中的多环芳烃

使用新型活性炭纤维(ACF)作为固相微萃取(SPME)技术的萃取纤维,检测了海水中的多环芳烃。得到ACF-SPME萃取多环芳烃的最优条件为:在搅拌条件下,盐浓度10%,pH3,温度60℃水浴中直接萃取40min。并确定16种多环芳烃的RSD(n=5)为1.8%～10%、线性范围为0.1～500μg/L、检出限为0.1～100μg/L。对东海近海海水进行了分析,结果表明海水中PAHs浓度在检测限以下,同时进行加标回收实验,得到16种多环芳烃的回收率在80%～128%。     

超临界CO_2萃取/气相色谱-质谱联用测定纺织品中邻苯二甲酸酯

采用超临界CO_2萃取技术(SFE-CO_2)从纺织品中萃取了邻苯二甲酸酯类增塑剂。探讨了不同萃取条件(萃取压力、萃取温度、萃取时间、共溶剂种类、收集溶剂种类)对邻苯二甲酸酯萃取率的影响,建立了超临界CO_2流体萃取/气相色谱-质谱联用(SFE-CO_2/GC-MS)法测定纺织品中13种邻苯二甲酸酯的检测方法。研究表明:采用正己烷为共溶剂和接收剂,萃取温度60℃、压力35 MPa,萃取时间60 min的条件最佳,萃取物经GC-MS测定,邻苯二甲酸二异癸酯在10～1000μg/mL范围内线性关系良好,其余12种邻苯二甲酸酯在1～500μg/mL范围内线性关系良好,相关系数为0.9917～0.9994,加标回收率在80.0%～117.2%之间,RSD在1.1%～7.2%之间。     

固相微革取-气相色谱-质谱联用测定海水与沉积物中邻苯二甲酸酯类污染物

邻苯二甲酸酯(PAEs)是塑化剂产品中使用最广泛的一类化合物,准确分析海洋中邻苯二甲酸酯的种类、组成及浓度水平,对认识PAEs在海洋环境的迁移变化及生态效应具有重要意义.本研究建立了固相微萃取-气相色谱-质谱联用技术分析海水与沉积物中PAEs的方法,确定了萃取时间、萃取温度等最佳实验条件.本方法测定海水与沉积物中PAEs含量的精密度为±10%,检出限分别为0.04~0.32 ng/L和0.12~1.60μg/kg;除邻苯二甲酸二甲酯(DMP)外,海水中PAEs回收率为68.0%~114.0%,沉积物中PAEs回收率为76.4%~105.0%.利用本方法测得长江口及其邻近海域水体与沉积物中PAEs的浓度分别为0.270~1.39μg/L和0.79~34.8μg/kg.实验表明,本方法操作简单,准确度高,大大缩减了海水萃取体积,能够应用于近岸海水与沉积物中PAEs含量的准确分析.     

顶空液相微萃取-气相色谱法测定盐酸雷尼替丁中二氯甲烷和三氯甲烷的残留量

采用顶空液相微萃取与气相色谱联用技术测定雷尼替丁中二氯甲烷和三氯甲烷的残留量。自制了萃取液保护装置。考察了萃取溶剂的种类、萃取时间、萃取温度、萃取液的体积对二氯甲烷和三氯甲烷萃取效果的影响。以正十三烷为萃取剂,在60 ℃下萃取30 min,萃取液滴体积2 μL。二氯甲烷含量在1～10 μg/g范围内与色谱峰高呈线性关系,相关系数(r2)为0.9733;三氯甲烷含量在1～10 μg/g范围内与色谱峰高呈线性关系,r2为0.9724。二氯甲烷和三氯甲烷的最低检出限分别为0.0273 μg/g和0.0410 μg/g,加标回收率分别为93.6%～102%和98.1%～103%。方法简便易行,测定结果准确。     

固相萃取-反相高效液相色谱法测定水中的邻苯二甲酸酯

建立了固相萃取-反相高效液相色谱法检测水中3种邻苯二甲酸酯类物质邻苯二甲酸二甲酯、邻苯二甲酸二(2-乙基己基)酯、邻苯二甲酸二正辛酯的方法. 考察了固相萃取柱、洗脱溶剂、洗脱体积、上样速度以及洗脱速度对萃取效率的影响. 通过综合分析, 选定SupelcleanLC-18 SPE Tube固相萃取柱, 甲醇为洗脱剂, 洗脱体积2 mL, 上样速度为4 mL/min, 洗脱速度为1 mL/min. 在此萃取条件下, 萃取回收率在83.4%～121.2%之间. 邻苯二甲酸二甲酯、邻苯二甲酸二(2-乙基己基)酯、邻苯二甲酸二正辛酯质量浓度在2～100 mg/L之间均为线性. 经萃取后, 方法的最低检出限分别为邻苯二甲酸二甲酯0.06 μg/L, 邻苯二甲酸二(2-乙基己基)酯0.16 μg/L, 邻苯二甲酸二正辛酯0.08 μg/L. 方法的精密度在10%～15%之间. 应用该方法测定自来水中酞酸酯类化合物的含量, 加标回收率为83.6%～110.2%.     

固相微萃取-气相色谱法测定白洋淀水样中的邻苯二甲酸酯类化合物

建立了固相微萃取(SPME)-气相色谱法(GC)分析环境水样中痕量邻苯二甲酸酯类化合物(PAEs)的方法。选用100 μm聚二甲基硅烷(PDMS)萃取纤维,在磁力搅拌条件下,对水样中的PAEs萃取富集60 min,然后直接注入GC进样口,在250 ℃温度下解吸4 min后进行分析测定,13种PAEs能得到充分提取和分离。方法的重现性(以相对标准偏差(RSD)计为0.2%～9.7%,检出限为0.02～0.83 μg/L。将本方法应用于白洋淀水样中PAEs的分析检测发现,样品中邻苯二甲酸二异丁酯(DIBP)、邻苯二甲酸二丁酯(DBP)、邻苯二甲酸二(2-乙基己基)酯(DEHP)检出率相对较高。对水样进行两个浓度水平(2.5 μg/L和5.0 μg/L)的加标试验,加标回收率为75.3%～111.0%,RSD为2.1%～8.0%(n=3),能够满足环境水样中痕量PAEs的测定要求。     

顶空-固相微萃取/气相色谱-质谱联用法快速分析海水中13种苯系物

建立了同时测定海水中常见的13种痕量苯系物（BTEX）的顶空-固相微萃取/气相色谱-质谱联用（HS-SPME/GC-MS）检测方法。利用涂有100 μm Polydimethylsiloxane（PDMS）涂层的萃取头顶空萃取海水样品,GC-MS检测和外标定量法对目标物进行分析。实验对萃取纤维头的类型、萃取温度、萃取时间、解吸时间、样品体积等主要萃取条件进行了优化。在优化萃取条件下,13种苯系物的线性范围为0.16~32 μg/L,相关系数为0.999 0~1.000 0,检出限为0.006~0.043 μg/L。在3个加标水平（0.16、1.6、16 μg/L）下,海水样品中13种苯系物的回收率为80.0%~117%,相对标准偏差（RSD,n=6）为2.0%~5.6%。该方法前处理简便易行、灵敏度高,为海水中痕量苯系物的检测提供了一种简便、快捷、环保的测定方法。     

悬浮固化分散液液微萃取-高效液相色谱法测定水体中邻苯二甲酸酯

建立了悬浮固化分散液液微萃取（SFO-DLLME）结合高效液相色谱（HPLC）快速测定水样中6种邻苯二甲酸酯（PAEs）的分析方法。通过对影响萃取效率因素的优化,确定了最佳萃取条件：十二烷醇萃取剂20 μL、萃取温度60℃、离子强度20 g/L、萃取时间1 min。6种PAEs在2~2000 μg/L范围内呈良好的线性关系,相关系数（r）为0.9995~0.9999,检出限（S/N=3）为0.3~0.6 μg/L。对自来水、湖水、江水、污水、海水、市售塑料瓶装纯净水和矿泉水进行测定,能检测到部分PAEs。对加标水样进行回收率试验（10、100和1000 μg/L）,6种PAEs的回收率为84.9%~94.5%,相对标准偏差为4.1%~6.8%（n=5）。该法环保、简单,可用于实际水样中6种PAEs的检测分析。     

计算机拟合技术研究C18柱在富集PAEs时的萃取条件

利用固相萃取技术富集了水中5种邻苯二甲酸酯类(邻苯二甲酸二甲酯(DMP)、邻苯二甲酸二乙酯(DEP)、邻苯二甲酸二丁酯(DBP)、邻苯二甲酸二(2-乙基己基)酯(DEHP)、邻苯二甲酸二辛酯(DOP)).借助均匀设计法及计算机回归建模优化技术对5种PAEs的固相萃取条件进行了设计与优化,得到最佳固相萃取条件为: 洗脱剂配比: V(正己烷)∶V(丙酮)=30∶1,洗脱体积2 mL,洗脱流速为4 mL/min,上样流速8 mL/min.富集后的样品用带电子捕获检测器的毛细管气相色谱检测,方法的线性范围为1～1000 μg/L (DMP,DEP,DOP),0.2～100 μg/L (DBP,DEHP);线性回归方程的相关系数为0.9970～1.000,检出限为0.02～0.4 μg/L,方法回收率为69%～117%,相对标准偏差为2.2%～9.5%.     

固相萃取-电感耦合等离子体质谱（ICP-MS）法测定海水中6种金属元素

为了实现海水中金属元素的绿色分离和快速检测,建立了新型螯合树脂为填料,固相萃取-电感耦合等离子体质谱（ICP-MS）测定海水中6种金属元素含量的方法。海水中Cu,Pb,Co,Ni,Cr,Mo金属离子与亚氨基二乙酸型螯合树脂形成螯合物,经固相萃取、洗脱,实现金属离子从海水中定量分离富集。在最佳实验条件下,测得方法的相对标准偏差（RSD）为1.7 %～3.6 % ,加标回收率为82.6 %～102 %,检出限为0.03 μg /L～0.15 μg /L。本研究采用亚氨基二乙酸型螯合树脂为填料的固相萃取,实现了海水分析的绿色样品前处理方法,与ICP-MS相结合用于海水标准样品和实际样品的分析,获得了满意的结果。     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives

Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.     

A general and convenient synthesis of 4-(tosylmethyl)semicarbazones and their use in amidoalkylation of hydrogen,heteroatom, and carbon nucleophiles

A general synthesis of previously unknown semicarbazone-based α-amidoalkylating reagents, 4-(tosylmethyl)semicarbazones, has been developed. The synthesis involved three-component condensation of semicarbazones of aliphatic or aromatic aldehydes with the same or other aldehydes and p-toluenesulfinic acid. The scope and limitations of this reaction were investigated. The compounds obtained were demonstrated to be an efficient α-(4-semicarbazono)alkylating agents. They were reacted with H- (sodium borohydride), O- (sodium methylate), S- (sodium phenylthiolate), N- (pyrrolidine, sodium succinimide), P- (trialkyl phosphites), and C-nucleophiles (sodium diethyl malonate) to give the corresponding products of the tosyl group substitution, 4-substituted semicarbazones, including analogues of nitrofurazone. Among the prepared compounds tested in vitro for antibacterial and antifungal activity, three nitrofuryl-containing semicarbazones exhibited high biological activities with minimum inhibitory concentration (MIC) values of 8–32 μg/mL.     

Synthesis of novel chiral bidentate hydroxyalkyl-N-heterocyclic carbene ligands and their application in palladium-catalyzed Mizoroki–Heck couplings and asymmetric addition of diethylzinc to benzaldehyde

A small library of new chiral bidentate hydroxyalkyl-imidazolium salts 1 is conveniently synthesized on multi-gram scale from inexpensive and commercially available chiral pool amino acids. The corresponding carbenes, generated by deprotonation of imidazolium salts 1, in combination with palladium(II) chloride were tested in the Mizoroki–Heck coupling reaction. The most significant results in terms of yields and reactivities were achieved with low catalyst loading. The catalytic activities of these imidazolium salts were also investigated in the asymmetric addition of diethylzinc to benzaldehyde. The use of MgO nanoparticles as an additive in conjunction with these ligands played a crucial role in increasing the efficiency of these reactions.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

Microwave-assisted copper-catalyzed stereoselective ring expansion of three-membered heterocycles with α-diazo-β-dicarbonyl compounds

Microwave-assisted copper-catalyzed ring expansions of three-membered heterocycles with α-diazo-β-dicarbonyl compounds were investigated. Thiiranes generated 3-acyl-5,6-dihydro-1,4-oxathiines in the presence of copper sulfate and trans-3-acyl-5,6-dihydro-1,4-oxathiines as stereospecific products for 1,2-disubstituted cis-thiiranes through an intramolecular S_N2 process. Oxiranes gave rise to 2-acyl-5,6-dihydro-1,4-dioxines under the catalysis of copper hexafluoroacetylacetonate and cis-3-acyl-5,6-dihydro-1,4-dioxines as stereospecific products for 1,2-disubstituted cis-oxiranes via an intimate ion-pair mechanism. The current method provides a direct and simple strategy in efficient preparation of 3-acyl-5,6-dihydro-1,4-oxathiines and 2-acyl-5,6-dihydro-1,4-dioxines, important agents in medicinal and agricultural chemistry, from readily available thiiranes and oxiranes, respectively.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.