Simultaneous coupling of capillary supercritical fluid chromatography and high temperature glass capillary gas chromatography to a mass spectrometer

The coupling of glass capillary supercritical fluid chromatography to a high temperature GC/MS system via a micrometeradjustable glass capillary interface including an integrated pressure restrictor is described. With this coupling device, both complementary capillary chromatographic methods retain their full independence and flexibility. It is shown that in supercritical fluid chromatography glass fulfils all the requirements of a suitable support material. The preparation of narrow bore glass capillary columns (0.06 mm i.d.), coated with chemically bonded and crosslinked fluids with a film thickness of about 0.6 μm, which exploit the merits of OHterminated polysiloxanes as stationary phases is discussed. The application of glass capillary SFC is demonstrated and compared with examples given in the literature.     

Open tubular column supercritical fluid chromatography/mass spectrometry on a benchtop mass spectrometer

A benchtop SFC/MS system is described which utilizes supercritical carbon dioxide in a 50 micron diameter open tubular column interfaced directly to an unchanged commercially available benchtop capillary GC/MS system equipped with a chemical ionization (CI) source. A small amount of methane reagent gas was admitted co-axially to a capillary restrictor at the exit of the capillary chromatographic column. This make-up gas served as the CI reagent gas and appeared to optimize the sensitivity of the system while providing abundant (M+1) ions for the analytes investigated in this study. Good chromatographic intergrity was obtained for the GC/MS test compound, decafluorotriphenylphosphine (DFTPP), but the capillary restrictor appeared to cause some tailing of the ion current profiles resulting from low nanogram levels of caffeine and some fatty acid esters. Improvements in the SFC/MS capillary restrictor interface and the pumping system of the benchtop GC/MS system should increase the capability of this system for future applications.     

Analysis of pyrethrins using capillary supercritical fluid chromatography and capillary gas chromatography with fourier transform infrared detection

The six insecticidally active components in a commercial preparation of pyrethrin extract are separated by capillary gas chromatography (GC) and by capillary supercritical fluid chromatography (SFC). Thermal degradation of pyrethrin I and II are observed under the GC conditions required to separate the pyrethrin components. The use of shorter columns and thinner stationary phase coatings reduce the amount of degradation but cannot eliminate degradation of pyrethrin II. The SFC chromatograms, obtained under thermally mild conditions, show that all components including pyrethrin II elute without degradation. Infrared spectra of cinerin I & II, jasmolin I & II, and pyrethrin I & II are obtained using a flow through SFC/IR detection cell. Spectra clearly reveal the structural differences needed to distinguish and identify the components in the extract.     

Reviews on recent trends in chromatography/mass spectrometry coupling. Part IV. Reasons why supercritical fluid chromatography is not so easily coupled with mass spectrometry as originally assessed

Summary When SFC was rediscovered in the early 1980s, it was frequently estimated that a strong driving force to its development would be the ease of devising a simple SFC/MS interface. This was believed to be easily achieved if analytical conditions were limited to capillary SFC columns as a general separation tool, and to the choice of neat CO₂ as the unique supercritical fluid. The low flow rate of mobile phase delivered by capillary columns was easy to accommodate by the vacuum equipment of standard mass spectrometers, and the specific physical properties of CO₂ made possible solute ionization by different ion-molecule reactions, especially charge exchange ionization. This approach has lived up to all of its promises. The major causes of the observed mismatch are the large variations of the MS source pressure as a result of the CO₂ pressure gradient at the SFC column inlet, the low sensitivity of charge exchange ionization at these high MS source pressures, and the inability to handle polar and nonvolatile molecules. Adaptation of LC/MS interfaces, such as the thermospray interface or the particle beam interface, to SFC/MS conditions was a step forward, but these devices have their own limitations. Alternative methods to direct SFC/MS coupling have been investigated recently. They are based on the use of packed columns rather than capillaries, and on solute ionization at atmospheric pressure rather than under a vacuum, by means of either gas-phase corona discharge ionization or liquidphase electrospray ionization. These new developments may revive research into the design of reproducible and sensitive SFC/MS systems where the number of recent studies is still low compared with other chromatography/mass spectrometry coupling studies.See [1] for part III     

Direct coupling of capillary supercritical fluid chromatography to high resolution mass spectrometry with minimum modification

Summary The coupling of a capillary supercritical fluid chromatograph with a high resolution double focusing mass spectrometer has been accomplished without any modifications to the pumping or ion source systems. The interface utilizes a direct insertion probe (DIP), which was originally designed for the direct analysis of solid samples, together with a trit restrictor as a decompression device. The DIP is placed opposite to the SFC restrictor, and it provides sufficient heat to prevent cluster formation and cooling resulting from the expansion of the supercritical fluid into the vacuum environment. Excellent mass spectra of standard polycyclic aromatic hydrocarbons under chemical-ionization (CI) conditions using methane as the reagent gas, and under charge-exchange (CE) conditions using CO₂ as the charge exchange medium were obtained.     

Columns in analytical-scale supercritical fluid chromatography: From traditional to unconventional chemistries

Within this review, we thoroughly explored supercritical fluid chromatography (SFC) columns used across > 3000 papers published from the first study carried out under SFC conditions in 1962 to the end of 2022. We focused on the open tubular capillary, packed capillary, and packed columns, their chemistries, dimensions, and trends in used stationary phases with correlation to their specific interactions, advantages, drawbacks, used instrumentation, and application field. Since the 1990s, packed columns with liquid chromatography and SFC-dedicated stationary phases for chiral and achiral separation are predominantly used. These stationary phases are based on silica support modified with a wide range of chemical moieties. Moreover, numerous unconventional stationary phases were evaluated, including porous graphitic carbon, titania, zirconia, alumina, liquid crystals, and ionic liquids. The applications of unconventional stationary phases are described in detail as they bring essential findings required for further development of the supercritical fluid chromatography technique.     

Chromatography with dense gases

Summary A capillary restrictor for supercritical fluid chromatography (SFC) with CO₂ was made by using a micro torch and fine emery cloths or grinding blocks. This restrictor could be drawn out either directly from the end of the analytical capillary column, or from a short piece of any capillary, which was then connected to the analytical column by standard techniques. It was found that the base current of a flame ionisation detector (FID) depends strongly on the position of the capillary end with respect to the FID flame tip and on the CO₂ grade, of course. Best results have been achieved at around 5 to 7 mm distance between the restrictor and the flame tip ends, and using SFC grade CO₂.     

Unified gas and supercritical fluid chromatography on 50 μm i.d. Columns

A unified approach to sequential gas and supercritical fluid Chromatography using 50 μm i.d. open tubular columns is described. Sample introduction is performed by means of a rotary injection valve. In order that linear velocities can be optimized independently, a second rotary valve in the chromatographic oven is used to direct the flow of column eluate to the flame ionization detector through either fused silica tubing in GC, or a frit restrictor in SFC. Applications of sequential GC-SFC on a 50 μm i.d. open tubular column are demonstrated, and comparisons made between sequential GC-SFC on 50 and 100 μm i.d. columns.     

Supercritical fluid chromatography of imidazole derivatives

Summary The aim of this work was to use SFC to separate simple, slightly basic, imidazole derivatives which are used for the synthesis of more complex molecules with therapeutic properties. Control of their purity utilizes separation techniques and this paper shows what SFC can do in comparison with LC which requires derivatization before detection and with GC where peak tailing can be a problem. Our results concern the use of sub-critical mixtures of CO₂ and polar modifiers because imidazole derivatives react with neat CO₂, thus failing to elute from packed columns, and are only partially resolved on capillary columns with neat N₂O. Therefore, separations with CO₂-alcohol-amine-water mixtures on aminopropyl-bonded silica with UV detection are discussed. The resolution and sensitivity limits allow real sample analysis within a very short time.     

Partition of supercritical n-pentane into SE-54 and SE-30 stationary phases in capillary supercritical fluid chromatography

Summary The mass spectrometric tracer pulse (MSTP) chromatography method was used to measure the amount of supercritical n-pentane dissolved or adsorbed into SE-54 and SE-30 capillary columns. Partition data were measured above the critical point of n-pentane at temperatures from 200 ° to 300 °C and pressures between 35.04 and 54.42 atm. The data obtained provide evidence for mobile fluid solubility or adsorption into the stationary phase under the conditions of supercritical fluid chromatography (SFC). At 220 °C, solubility and/or adsorption of supercritical n-pentane decreases by increasing the pressure and reaches a minimum at approximately 45.00 atm. The effect of mobile-fluid pressure on its solubility or adsorption becomes limited at temperatures over 260 °C. This study demonstrates the unique experimental capabilities of the MSTPC method for quantitative measurement of the physico-chemical interaction of the complex multicomponent system encountered in SFC which is not possible by any other technique. An innovative instrumental design for modification of GC/MS systems for SFC, GC/MS operation is also described.

---

Verteilung von superkritischem n-Pentan in den stationären Phasen SE-54 und SE-30 bei der Capillar-Chromatographie mit superkritischen fluiden Phasen

     

Rapid analysis using capillary supercritical fluid chromatography

Capillary supercritical fluid chromatography (SFC) is proving to be a viable and useful separation method for thermally labile and nonvolatile materials. As with other capillary chromatographic techniques, very fast separations can be accomplished by sacrificing total efficiency and optimizing the conditions for rapid analysis. This is achieved using short, small-bore capillary columns, increased mobile phase linear velocities and very fast pressure programming rates. These principles are demonstrated for the rapid separation of selected component systems.     

Serially coupled capillary columns supercritical fluid chromatography with a coupling restrictor.

A serially coupled column system for capillary supercritical fluid chromatography was constructed by connecting two capillary columns of different polarities using or without using a coupling restrictor. The influence of the column sequence, the size of the coupling restrictor and the column temperature on the polarity of the system were studied. The system without a coupling restrictor (the directly coupled system) provided an intermediate polarity between two columns, depending on the column geometry, such as the film thickness and column length, although it slightly shifted to that of the first column. In the system with a coupling restrictor, the contribution of the second column to the overall retention increased with its resistance. The use of a coupling restrictor allowed to control the polarity of the coupled system virtually over the whole range between two columns. The temperature was an additional effective parameter for tuning the polarity of the system.     

Rapid and high resolution capillary supercritical fluid chromatography (SFC) and SFC/MS of trichothecene mycotoxins

The potential application of capillary column supercritical fluid chromatography (SFC) and SFC/mass spectrometry (SFC/MS) for the separation and analysis of mycotoxins of the trichothecene group was examined. Trichothecenes present significant analytical problems for both gas and liquid chromatography with a major difficulty for the latter being the lack of sufficiently sensitive and selective detectors. Supercritical carbon dioxide mobile phases at temperatures up to 100 degrees C were used with deactivated fused silica columns coated with crosslinked stationary phases. Separations were obtained under pressure ramped conditions using long (15 m) 50-micron i.d. columns for several trichothecenes (diacetoxyscirpenol, deoxynivalenol, and T-2 toxin) and related higher molecular weight macrocyclic (roridin and verrucarin) trichothecenes. In addition, new rapid pressure programming techniques with short (less than 2m) 25- to 50-micron i.d. capillary columns were used to obtain fast separations in as little as 1 min. SFC/MS with ammonia chemical ionization provided high selectivity and sensitive detection (with approximately 1-pg detection limits) for trichothecene mixtures. The extension to complex sample matrices is discussed and the application of selective MS/MS detection is demonstrated.     

Supercritical fluid chromatography/mass spectrometry using a simple capillary-direct interface

Summary A simple method for interfacing capillary supercritical fluid chromatography with a commercial quadrupole mass spectrometer (SFC/MS) has been developed that yields good chromatographic peak shapes and good sensitivity. No modification of the mass spectrometer is required, and a single instrument can be used for both SFC/MS and GC/MS with conversion between modes requiring less than 20 min. SFC/MS separations and chemical ionization mass spectra of wax components, a triazine pesticide metabolite, abietic acid, and high molecular weight polycyclic aromatic hydrocarbons are reported.

---

Kombination von Chromatographie mit überkritischen fluiden Phasen und Massenspektrometrie unter Verwendung eines einfachen direkten Capillar-Interface

     

A model for quantitatively describing linear velocity programming in capillary SFC

Summary Linear velocity in capillary SFC is commonly controlled by restricting capillaries. In this paper, a model is described that quantitatively predicts the linear velocity of a supercritical fluid in SFC using tapered or ceramic frittype restrictors. In this model, the flow from the restricting capillary is assumed to be an isentropic expansion. The variation of the linear velocity as a function of pressure, temperature and cross-sectional area of the restricting aperture was predicted by this model. This predictive capability is important to the use of gradient programming in capillary SFC. Finally, the ideal variable restrictor for gradient programming was found to be one that could reversibly increase or decrease the linear velocity independent of the pressure, temperature, and/or density conditions used to create the gradient.     

On-line multidimensional supercritical fluid chromatography/capillary gas chromatography

A new analytical technique combining on-line supercritical fluid chromatography with capillary gas chromatography has been developed. The supercritical fluid sample effluent is decompressed through a restrictor directly into a conventional capillary gas chromatographic injection port. This technique allows for not only direct (100%) sample transfer from the supercritical fluid chromatograph to the gas chromatograph but also for selective or multi-step heartcutting of various sample peaks as they elute from the supercritical fluid chromatograph. Heartcut times are determined by monitoring the responses from the flame ionization or ultraviolet absorbance detectors on the supercritical fluid chromatograph. This report describes the operational setup and provides the results of heartcut reproducibility experiments using normal hydrocarbon and aromatic test mixtures. Results from studies where operational parameters were varied, such as GC injector temperature, will also be provided. The potential usefulness of this new technique for selective heartcutting will also be demonstrated using complex hydrocarbon streams.     

Evaluation of an ion mobility detector for supercritical fluid chromatography with solvent-modified carbon dioxide mobile phases

Summary An ion mobility detector (IMD) was evaluated for open tubular column supercritical fluid chromatography (SFC) when organic solvent-modified supercritical CO₂ was used as mobile phase. It was found that the SFC/IMD interface design in which the SFC capillaray restrictor was directly inserted into the ionization region of the IMD was not acceptable because of low sensitivity that resulted from the effect of the modifier on detector temperature and mechanism of detection. A new interface utilizing a heated nebulizer gas to provide heat to the restrictor and to minimize the formation of ion clusters, and a bent nozzle for enhancing the ionization efficiency of the solute in the IMD ion source are described. Using 5% acetonitrile in CO₂, the minimum detectable quantity (S/N=3) for pyrene was improved from 25.2 ng to 2.1 ng with the new detector design. This compares to a minimum detectable quantity of 0.1 ng when using neat CO₂ as mobile phase. The use of molecular connectivity calculations to predict the drift times of selected analytes is also successfully demonstrated.     

Supercritical fluid chromatography: A technology update

Summary Significant advances continue to be made in supercritical fluid chromatography both in the instrumentation and application areas. Both packed and wider bore capillary columns are being extensively investigated. Detector designs and interfaces are being reviewed with a great deal of work also going into restrictor and injection technology. The paper focusses on these current developments and how they impact the role of supercritical fluid chromatography in the analytical laboratory.

---

Chromatographie mit überkritischen fluiden Phasen: Stand der Technik

     

Supercritical fluid chromatography with a slurry-packed capillary column

A versatile system with a slurry-packed capillary column was developed for supercritical fluid chromatography, which is capable of programming both inlet and outlet pressure independently, as well as using a restrictor to apply back pressure. This system revealed the relationships between pressure drop, flow rate, and linear velocity in pressure-programmed supercritical fluid chromatography. In the restrictor system, both the pressure drop and the flow rate increased almost linearly with inlet pressure, while under conditions of constant pressure drop characteristic behavior was observed which depended on the density-viscosity relationships of supercritical fluid. Resolution in the separation of polysiloxane oligomers was found to be increased by increasing the ratio of pressure drop to pressure-programming rate, although the sensitivity decreased due to the increase in peak volume. The system controlling both inlet and outlet pressure has distinct advantages over the restrictor system controlling both inlet and outlet pressure has distinct advantages over the restrictor system in practical in practical operations.     

Application of capillary supercritical fluid chromatography to the analysis of a middle distillate fuel

Summary The application of capillary supercritical fluid chromatography (SFC) to the analysis of a middle distillate fuel is described. Small diameter (50m i.d.) fused-silica capillary columns coated with crosslinked 50% phenyl polymethylphenyl siloxane provided high separation efficiency and good compatibility with flame ionization detection. High resolution separations of the chemical class fractions obtained by adsorption chromatography on alumina were obtained using carbon dioxide as the supercritical mobile phase and simple pressure programming techniques. In addition to the less polar fuel components, supercritical carbon dioxide allowed chromatography of the nitrogen-containing polycyclic aromatic hydrocarbon fraction and the hydroxylated polycyclic aromatic materials.