Research on field emission mechanism of nano-structured carbon film

The field emission (FE) characteristics of nano-structrued carbon films (NSCFs) are investigated. The saturation behaviour of the field emission current density found at high electric field E cannot be reasonably explained by the traditional Fowler-Nordheim (F-N) theory. A three-region E model and the curve-fitting method are utilized for discussing the FE characteristics of NSCFs. In the low, high, and middle E regions, the FE mechanism is reasonably explained by a modified F-N model, a corrected space-charge-limited-current (SCLC) model and the joint model of F-N and SCLC mechanism, respectively. Moreover, the measured FE data accord well with the results from our corrected theoretical model.     

Research on the field emission mechanism of nano-structured carbon film

The field emission(FE) characteristics of nano-structured carbon films(NSCFs) are investigated.The saturation behaviour of the field emission current density found at high electric field E cannot be reasonably explained by the traditional Fowler-Nordheim(F-N) theory.A three-region E model and the curve-fitting method are utilized for discussing the FE characteristics of NSCFs.In the low,high,and middle E regions,the FE mechanism is reasonably explained by a modified F-N model,a corrected space-charge-limited-current(SCLC) model and the joint model of F-N and SCLC mechanism,respectively.Moreover,the measured FE data accord well with the results from our corrected theoretical model.     

纳米晶ZrO2:Er3+-Yb3+的制备及其室温上转换发射

用化学共沉淀法制备了ZrO₂:Er³⁺-Yb³⁺纳米晶粉体，所制备的纳米晶粉体具有较强的室温上转换发射和红外发射.研究了样品的晶体结构和上转换发光性质随着Yb³⁺掺杂浓度和煅烧温度的变化关系.通过X射线衍射谱分析发现，经800℃煅烧2h后得到的ZrO₂:Er³⁺-Yb³⁺纳米晶是四方相和单斜相的混合结构，经950℃煅烧2h后得到的样品以单斜相为主，随着Y     

Annealing effects on the structure and electrical characteristics of amorphous Er2O3 films

Amorphous Er 2 O 3 films are deposited on Si (001) substrates by using reactive evaporation.This paper reports the evolution of the structure,morphology and electrical characteristics with annealing temperatures in an oxygen ambience.X-ray diffraction and high resolution transimission electron microscopy measurement show that the films remain amorphous even after annealing at 700 C.The capacitance in the accumulation region of Er 2 O 3 films annealed at 450 C is higher than that of as-deposited films and films annealed at other temperatures.An Er 2 O 3 /ErO x /SiO x /Si structure model is proposed to explain the results.The annealed films also exhibit a low leakage current density (around 1.38 × 10 4 A/cm 2 at a bias of 1 V) due to the evolution of morphology and composition of the films after they are annealed.     

超薄类金刚石膜生长和结构特性的分子动力学模拟

利用分子动力学模拟方法研究了2—3nm厚的类金刚石(DLC)薄膜在金刚石基体(100)表面上的生长过程. 分析了用来表征沉积后无定型碳膜质量的重要结构特性，如sp³杂化比例、薄膜密度、径向分布函数等，计算结果和现有的实验结果基本一致. 不同入射原子能量对结构特性进而对薄膜性能有重要影响，入射原子能量在20—60eV时，薄膜可以获得最优性能. 载能原子入射是生长均匀、连续、致密固体薄膜的前提，稳定的中间区域对于保证薄膜优良的力学性质是必需的. 关键词： DLC膜 分子动力学模拟 3杂化比例')" href="#">sp³杂化比例     

Upconversion emission enhancement of TiO2 coated lanthanide-doped Y2O3 nanoparticles

To investigate the upconversion emission,this paper synthesizes Tm3+ and Yb3+ codoped Y2O3 nanoparticles,and then coats them with TiO2 shells for different coating times.The spectral results of TiO2 coated nanoparticles indicate that upconversion emission intensities have respectively been enhanced 3.2,5.4,and 2.2 times for coating times of 30,60 and 90 min at an excitation power density of 3.21×102 W.cm 2,in comparison with the emission intensity of non-coated nanoparticles.Therefore it can be concluded that the intense upconversion emission of Y2O3:Tm3+,Yb3+ nanoparticles can be achieved by coating the particle surfaces with a shell of specific thickness.     

Excimer laser deposition of thin amorphous carbon films

A new carbon film deposition technique, based upon excimer laser vaporization of graphite in a flowing gas system has been developed. The low temperature vapor (LTV) technique alleviates high temperatures occurring in most other deposition methods. In this technique the UV laser ablation occurs in an inert flowing gas atmosphere. Atoms and molecules evaporated from graphite are cooled by gas entrainment before condensing on a substrate. The resulting films of amorphous carbon or hydrogenated amorphous carbon are free from strain. Measurement of the optical band gap of these films shows that E_g can be controlled by the hydrogen content of the carrier gas.     

金刚石薄膜的结构特征对薄膜附着性能的影响

在不同实验条件下，用微波等离子体化学气相沉积设备在硬质合金(WC+6%Co)衬底上沉积了 具有不同结构特征的金刚石薄膜.用Raman谱表征薄膜的品质和应力，用压痕实验表征薄膜的 附着性能，考察了薄膜中sp²杂化碳含量、形核密度、薄膜厚度对薄膜附着性能 的影响.结 果表明：sp²杂化碳的缓冲作用使薄膜中sp²杂化碳的含量对薄膜中 残余应力有较大的影 响，从而使薄膜压痕开裂直径统计性地随sp²杂化碳含量的增加而减小；仅仅依 靠超声遗 留的金刚石晶籽提高形核密度并不能有效改变薄膜与硬质合金基体之间的化学结合状况，从 而不能有效提高薄膜在衬底上的附着性能；在薄膜较薄时，晶粒之间没有压应力的存在，开 裂直径并不明显随厚度增加而增加，只有当薄膜厚度增加到一定值，晶粒之间才有较强压应 力存在，开裂直径随厚度的增加而较为迅速地增加. 关键词： 金刚石薄膜 附着性能 2杂化碳')" href="#">sp²杂化碳 成核密度 薄膜厚度     

氟化非晶碳薄膜的光学带隙分析

研究了CHF3C6H6沉积的氟化非晶碳(αC∶F)薄膜的光学带隙.发现αC∶F薄膜光学带隙的大小取决于薄膜中C—F,CC的相对含量.这是由于CC形成的窄带隙π键和C—F形成的宽带隙σ键含量的相对变化,改变了带边态密度分布的结果.在微波功率为140—700W、沉积气压为01—10Pa、源气体CHF3∶C6H6流量比为1∶1—10∶1条件下沉积的αC∶F薄膜,光学带隙在176—398eV之间 关键词： 氟化非晶碳(αC∶F)薄膜 光学带隙 键结构     

Electron emission studies of CNTs grown on Ti and Ni containing amorphous carbon nanocomposite films

Carbon nanotubes (CNTs) were grown successfully on the as-deposited dual metal (Ti and Ni) embedded films using a radio frequency plasma-enhanced chemical vapor deposition system. The microstructure of CNTs grown on the dual metal films proved to be heavily dependent on the percentages of metals included, varying both in size and in density. Electron emission tests carried out on the films with CNTs grown showed that the threshold field was dependent on the surface morphology of the CNTs, with the lowest threshold field at 3.5 V/μm from 2.5% Ti/Ni film with CNTs. The field enhancement factor, β, of the emitting tips was also calculated from the Fowler–Nordheim plots, where CNTs from the 2.5% Ti/Ni film gave the highest field enhancement factor. However, it was observed that films with a single metal of either Ti or Ni did not manage to grow CNTs, possibly due to a lack of catalyst centres at the surface of the films. It was believed that the Ni nanoclusters acted as catalysts centres giving a rather uniform but randomly orientated type of CNTs. Results obtained pointed that the fabricated nanocomposite material could be a possible choice for cold cathode emitters and the Ti/Ni mixture could be an effective composite for controlling the CNT density.     

Synchrotron radiation photoelectron spectroscopy and near-edge X-ray absorption fine structure study on oxidative etching of diamond-like carbon films by hyperthermal atomic oxygen

Surface structural changes of a hydrogenated diamond-like carbon (DLC) film exposed to a hyperthermal atomic oxygen beam were investigated by Rutherford backscattering spectroscopy (RBS), synchrotron radiation photoelectron spectroscopy (SR-PES), and near-edge X-ray absorption fine structure (NEXAFS). It was confirmed that the DLC surface was oxidized and etched by high-energy collisions of atomic oxygen. RBS and real-time mass-loss data showed a linear relationship between etching and atomic oxygen fluence. SR-PES data suggested that the oxide layer was restricted to the topmost surface of the DLC film. NEXAFS data were interpreted to mean that the sp² structure at the DLC surface was selectively etched by collisions with hyperthermal atomic oxygen, and an sp³-rich region remained at the topmost DLC surface. The formation of an sp³-rich layer at the DLC surface led to surface roughening and a reduced erosion yield relative to the pristine DLC surface.     

Ce3+对Er3+/Yb3+共掺TeO2-WO3-ZnO玻璃发光性能的影响

在Er³⁺/Yb³⁺共掺TeO₂-WO₃-ZnO玻璃中引入Ce³⁺，研究了Ce³⁺对Er³⁺1.5μm发射性能及其上转换发光性能的影响。结果表明，随Ce³⁺浓度的增加Er³⁺1.5μm波段的荧光强度先增强后降低，优化的Ce³⁺掺杂浓度在2.07×10²⁰/cm³左右；1.5μm波段的荧光寿命则随Ce³⁺浓度的增加有轻微降低，从3.4ms降到3.0ms，但Ce³⁺浓度的增加对1.5μm波段的荧光半高宽基本无影响；Er³⁺/Ce³⁺间的交叉弛豫Er³⁺(⁴I_11/2)+Ce³⁺(²F_5/2)→Er³⁺(⁴I_13/2)+Ce³⁺(²F_7/2)使玻璃的上转换发光强度大大降低，但在过高的Ce³⁺浓度下，Er³⁺/Ce³⁺间的另一交叉弛豫Er³⁺(⁴I_13/2)+Ce³⁺(²F_5/2)→Er³⁺(⁴I_15/2)+Ce³⁺(²F_7/2)则使Er³⁺⁴I_13/2能级粒子数减少，导致1.5μm波段荧光强度和荧光寿命降低. 关键词： 碲钨酸盐玻璃 发光性能 3+离子')" href="#">Er³⁺离子 3+离子')" href="#">Ce³⁺离子 交叉弛豫     

Blue light emission from Eu ions in sol-gel-derived Al2O3-SiO2 glasses

Blue light-emitting glasses were successfully prepared by doping Eu²⁺ ions in the system Al₂O₃-SiO₂. The Al₂O₃-SiO₂ glasses doped with Eu³⁺ ions were synthesized using a sol-gel method, followed by heating in hydrogen gas atmosphere to reduce into the Eu²⁺ ions. The obtained glasses exhibited emission spectra with peak at ∼450 nm due to 4f⁶5d→4f⁷ (⁸S_7/2) transition, the intensities of which strongly changed depending on their glass composition and heating conditions. The emission quantum efficiency of 48% was achieved by heating the glass with the ratio of Al³⁺ to Eu³⁺ at about 6 at 1000 °C in hydrogen gas atmosphere. It was found that the Al₂O₃-SiO₂ glasses were appropriate not only for homogeneously doping the Eu³⁺ ions in glass structure but also reducing to Eu²⁺ ions, resulting in enhanced blue light-emission properties.     

Hydrophilicity of amorphous TiO2 ultra-thin films

The UV-light-induced hydrophilicity of amorphous titanium dioxide thin films obtained by radio frequency magnetron sputtering deposition was studied in relation with film thickness. The effect of UV light irradiation on the film hydrophilicity was fast, strong and did not depend on substrate or thickness for films thicker than a threshold value of about 12 nm, while for thinner films it was weak and dependent on substrate or thickness. The weak effect of UV light irradiation observed for the ultra-thin films (with thickness less than 12 nm) is explained based on results of measurements of surface topography, UV-light absorption and photocurrent decay in vacuum. Comparing to thicker films, the ultra-thin films have a smoother surface, which diminish their real surface area and density of defects, absorb partially the incident UV light radiation, and exhibit a longer decay time of the photocurrent in vacuum, which proves a spatial charge separation. All these effects may contribute to a low UV light irradiation effect on the ultra-thin film hydrophilicity.     

Eu2+,Mn2+在BaZnP2O7中的发光及Eu2+→Mn2+能量传递

采用高温固相法合成了BaZnP₂O₇:Eu²⁺,Mn²⁺荧光粉,并对其发光性质及Eu²⁺对Mn²⁺的能量传递机理进行了研究.Eu²⁺和Mn²⁺在380 nm和670nm的发射峰分别由Eu²⁺的5d—4f跃迁和Mn²⁺的⁴T₁(^{4关键词： 磷酸盐 2+}')" href="#">Eu²⁺ 2+')" href="#">Mn²⁺ 能量传递     

Synthesis and field emission of diamond-like carbon nanorods on TiO2/Ti nanotube arrays

Highly ordered TiO₂/Ti nanotube arrays were fabricated by anodic oxidation method in 0.5 wt% HF. Using prepared TiO₂/Ti nanotube arrays deposited Ni nanoparticles as substrate, high quality diamond-like carbon nanorods (DLCNRs) were synthesized by a conventional method of chemical vapor deposition at 750 °C in nitrogen atmosphere. DLCNRs were analyzed by filed emission scanning electron microscopy and Raman spectrometer. It is very interesting that DLCNRs possess pagoda shape with the length of 3–10 μm. Raman spectra show two strong peaks about 1332 cm⁻¹ and 1598 cm⁻¹, indicating the formation of diamond-like carbon. The field emission measurements suggest that DLCNRs/TiO₂/Ti has excellent field emission properties, a low turn-on field about 3.0 V/μm, no evident decay at 3.4 mA/cm² in 480 min.     

Eu2+,Mn2+在BaZnP2O7中的发光及Eu2+→Mn2+能量传递

采用高温固相法合成了BaZnP₂O₇:Eu²⁺,Mn²⁺荧光粉，并对其发光性质及Eu²⁺对Mn²⁺的能量传递机理进行了研究.Eu²⁺和Mn²⁺在380 nm和670nm的发射峰分别由Eu²⁺的5d—4f跃迁和Mn²⁺的⁴T₁(^{4相似文献}   

类金刚石和碳氮薄膜的电化学沉积及其场发射性能研究

利用电化学方法在室温下成功地沉积了类金刚石(DLC)薄膜和非晶CN_x薄膜，并 对制备条件进行了讨论.通过扫描电子显微镜、傅里叶变换红外光谱技术，分析了薄膜的表面形貌和化学结合状态.场发射测量结果表明：DLC膜和非晶CN_x的开启场分别为88和 10V/μm；并且在23V/μm的电场下，DLC膜和非晶CN_x膜的发射电流密度分别达到10 和037mA/cm². 关键词： 电化学沉积 类金刚石薄膜 x薄膜')" href="#">CN_x薄膜 场致电子发射     

The study of ion mixed amorphous carbon films on single crystal silicon by C ion implantation

Amorphous-carbon (a-C) films were deposited on a single-crystal silicon substrate by vacuum vapor deposition system and these amorphous carbon films were implanted with 110 keV C⁺ at fluences of 1 × 10¹⁷ ions/cm². The effect of ion mixing on the surface morphology, friction behavior and adhesion strengths of amorphous carbon films was examined making use of atomic force microscopy (AFM), ball-on-disk reciprocating friction tester, nano-indentation system and scanning electron microscope (SEM). The changes in chemical composition and structure were investigated by using X-ray photoelectron spectroscopy (XPS). The results show that the anti-wear life and adhesion of amorphous carbon films on the Si substrates were significantly increased by C ion implantation. The SiC chemical bonding across the interface plays a key role in the increase of adhesion strength and the anti-wear life of amorphous carbon film. The friction and wear mechanisms of amorphous carbon film under dry friction condition were also discussed.     

Analytical potential energy function for the electronic states 2^∏1/2 and 2^∏3/2 of O^x2 （x=＋1, -1）

The splitting of potential energy levels for ground state X^2∏g of O^x2 （x = ＋1,-1） under spin-orbit coupling （SOC） has been calculated by using the spin-orbit （SO） multi-configuration quasi-degenerate perturbation theory （SO-MCQDPT）. Their Murrell-Sorbie （M S） potential functions are gained, and then the spectroscopic constants for electronic states 2^∏1/2 and 2^∏3/2 are derived from the M S function. The vertical excitation energies for O^x2 （x = ＋1,-1） are v[O2＋1^（2∏3/2→X^2∏1/2）] =195.652cm^-1, and v[O2^-1（2^∏1/2 →X^2∏3/2）] =182.568cm^-1, respectively. All the spectroscopic data for electronic states 2^∏1/2 and 2^∏3/2 are given for the first time.