Milk and serum standard reference materials for monitoring organic contaminants in human samples

Four new Standard Reference Materials (SRMs) have been developed to assist in the quality assurance of chemical contaminant measurements required for human biomonitoring studies, SRM 1953 Organic Contaminants in Non-Fortified Human Milk, SRM 1954 Organic Contaminants in Fortified Human Milk, SRM 1957 Organic Contaminants in Non-Fortified Human Serum, and SRM 1958 Organic Contaminants in Fortified Human Serum. These materials were developed as part of a collaboration between the National Institute of Standards and Technology (NIST) and the Centers for Disease Control and Prevention (CDC) with both agencies contributing data used in the certification of mass fraction values for a wide range of organic contaminants including polychlorinated biphenyl (PCB) congeners, chlorinated pesticides, polybrominated diphenyl ether (PBDE) congeners, and polychlorinated dibenzo-p-dioxin (PCDD) and dibenzofuran (PCDF) congeners. The certified mass fractions of the organic contaminants in unfortified samples, SRM 1953 and SRM 1957, ranged from 12 ng/kg to 2200 ng/kg with the exception of 4,4′-DDE in SRM 1953 at 7400 ng/kg with expanded uncertainties generally <14 %. This agreement suggests that there were no significant biases existing among the multiple methods used for analysis.

Production of standard reference material

Summary Deviations were reproduced repeatedly between certified and observed low phosphorus values in commercial standard reference steel samples when being analyzed thoroughly by photometry of the yellow phosphorus vanadato molybdenum complex after extraction by methyl isobutyl ketone. The values observed were by 14 ppm (min 2, max 26) lower as certified. The accuracy of these results on a choice of those samples was achieved and proved by primary calibration with pure substances with an interval of uncertainty of only 1.4ppm (95% confidence interval). As demonstrated this fact demands imparatively the documented application of primary calibration substances and suitable calibration methods when standard reference material is produced.

---

Zur Herstellung von StandardreferenzmaterialÜberprüfung des Phosphorgehaltes in Standardreferenzstählen im Bereich von 59–125 ppm P durch Primäreichung

Zusammenfassung Aufgrund von wiederholten und reproduzierbaren Abweichungen zwischen den Soll- und Ist-Gehalten niedriger Phosphorwerte in käuflichen Standardreferenzstählen wurde eine Auswahl dieser Proben sorgfältig durch Photometrie des gelben Phosphorvanadatomolybdänkomplexes nach MIBK-Extraktion untersucht. Die Richtigkeit der Ergebnisse, die etwa 14 ppm (min. 2, max. 26) unter den Angaben der Zertifikate liegen, wurde durch Primäreichung mit Reinsubstanzen mit einem Unsicherheitsbereich von nur 1,4 ppm (P=95%) nachgewiesen. Dieser Sachverhalt legt, wie gezeigt wird, die dokumentierte Anwendung von primären Eichsubstanzen und geeigneten Eichmethoden bei der Untersuchung künftiger Standardreferenzproben zwingend nahe.

---

---

The author thanks E. Weichert for efficient assistance with the practical work.     

Development of a gas standard reference material containing eighteen volatile organic compounds

Summary A procedure to prepare primary gas cylinder standards for eighteen volatile organic compounds (VOC's) at the 1–15 nmol/mol (ppb) level was developed. The gas standards that were prepared by this procedure were intercompared by using gas chromatography with flame ionization detection (GC-FID) and electron capture detection (GC-ECD). The data, gravimetric concentration of the standards versus the respective GC peak area response, were plotted for each compound and fitted using linear regression. The regression analysis showed excellent agreement among the standards for each compound. These gas standards were evaluated over a period of 2 years and were determined to be stable and accurate. This research resulted in the development of Standard Reference Material (SRM) 1804, which contains these 18 volatile organic compounds in nitrogen at a nominal concentration of 5 nmol/mol for each compound. A batch of cylinders containing the mixture was procured from a commercial supplier. Each cylinder in the batch was analyzed for each of the 18 components. The data showed that the batch was homogeneous and stable for 15 of the 18 organic compounds, resulting in certification and issuance of SRM 1804.     

Three new mussel tissue standard reference materials (SRMs) for the determination of organic contaminants

Three new mussel tissue standard reference materials (SRMs) have been developed by the National Institute of Standards and Technology (NIST) for the determination of the concentrations of organic contaminants. The most recently prepared material, SRM 1974b, is a fresh frozen tissue homogenate prepared from mussels (Mytilus edulis) collected in Boston Harbor, Massachusetts. The other two materials, SRMs 2977 and 2978, are freeze-dried tissue homogenates prepared from mussels collected in Guanabara Bay, Brazil and Raritan Bay, New Jersey, respectively. All three new mussel tissue SRMs complement the current suite of marine natural-matrix SRMs available from NIST that are characterized for a wide range of contaminants (organic and inorganic). SRM 1974b has been developed to replace its predecessor SRM 1974a, Organics in Mussel Tissue, for which the supply is depleted. Similarly, SRMs 2977 and 2978 were developed to replace a previously available (supply depleted) freeze-dried version of SRM 1974a, SRM 2974, Organics in Freeze-Dried Mussel Tissue. SRM 1974b is the third in a series of fresh frozen mussel tissue homogenate SRMs prepared from mussels collected in Boston Harbor starting in 1988. SRM 1974b has certified concentration values for 22 polycyclic aromatic hydrocarbons (PAHs), 31 polychlorinated biphenyl congeners (PCBs), and 7 chlorinated pesticides. Reference values are provided for additional constituents: 16 PAHs, 8 PCBs plus total PCBs, 6 pesticides, total extractable organics, methylmercury, and 11 trace elements. PAH concentrations range from about 2 ng g^–1 dry mass (cyclopenta[cd]pyrene) to 180 ng g^–1 dry mass (pyrene). PCB concentrations range from about 2 ng g^–1 dry mass (PCB 157) to 120 ng g^–1 dry mass (PCB 153). The reference value for total PCBs in SRM 1974b is (2020 ± 420) ng g^–1 dry mass. Pesticide concentrations range from about 4 ng g^–1 dry mass (4,4-DDT) to 40 ng g^–1 dry mass (4,4-DDE). SRM 2977 has certified values for 14 PAHs, 25 PCB congeners, 7 pesticides, 6 trace elements, and methylmercury. Reference values for 16 additional PAHs and 9 inorganic constituents are provided, and information values are given for 23 additional trace elements. SRM 2978 has certified and reference concentrations for 41 and 22 organic compounds, respectively, and contains contaminant levels similar to those of SRM 1974b. Organic contaminant levels in SRM 2977 (mussels from Guanabara Bay, Brazil) are typically a factor of 2 to 4 lower than those in SRM 1974b and SRM 2978. The organic contaminant concentrations in each new mussel tissue SRM are presented and compared in this paper. In addition, a chronological review of contaminant concentrations associated with mussels collected in Boston Harbor is discussed as well as a stability assessment of SRM 1974a.Electronic Supplementary Material Supplementary material is available in the online version of this article at . A link in the frame on the left on that page takes you directly to the supplementary material.     

Two new marine sediment standard reference materials (SRMs) for the determination of organic contaminants

Two new marine sediment standard reference materials (SRMs), SRM 1941b Organics in Marine Sediment and SRM 1944 New York/New Jersey Waterway Sediment, have been recently issued by the National Institute of Standards and Technology (NIST) for the determination of organic contaminants including polycyclic aromatic hydrocarbons (PAHs), polychlorinated biphenyl (PCB) congeners, and chlorinated pesticides. Both sediment SRMs were analyzed using multiple analytical methods including gas chromatography/mass spectrometry (GC/MS) on columns with different selectivity, reversed-phase liquid chromatography with fluorescence detection (for PAHs only), and GC with electron capture detection (for PCBs and pesticides only). SRM 1941b has certified concentrations for 24 PAHs, 29 PCB congeners, and 7 pesticides, and SRM 1944 has certified concentrations for 24 PAHs, 29 PCB congeners, and 4 pesticides. Reference concentrations are also provided for an additional 58 (SRM 1941b) and 39 (SRM 1944) PAHs, PCB congeners, and pesticides. SRM 1944, which was collected from multiple sites within New York/New Jersey coastal waterways, has contaminant concentrations that are generally a factor of 10–20 greater than SRM 1941b, which was collected in the Baltimore (Maryland) harbor. These two SRMs represent the most extensively characterized marine sediment certified reference materials available for the determination of organic contaminants.Electronic Supplementary Material Supplementary material is available in the online version of this article at . A link in the frame on the left on that page takes you directly to the supplementary material.     

Certified reference materials for inorganic and organic contaminants in environmental matrices

Chemical measurements often constitute the basis for informed decision-making at different levels in society; sound decision-making is possible only if the quality of the data used is uncompromised. To guarantee the reliability and comparability of analytical data an intricate system of quality-assurance measures has to be put into effect in a laboratory. Reference materials and, in particular, certified reference materials (CRMs) are essential for achieving traceability and comparability of measurement results between laboratories and over time. As in any other domain of analytical chemistry, techniques used to monitor the levels and fate of contaminants in the environment must be calibrated using appropriate calibration materials, and the methods must be properly validated using fit-for-purpose matrix-matched CRMs, to ensure confidence in the data produced. A sufficiently large number of matrix CRMs are available for analysis of most elements, and the group of chemicals known as persistent organic pollutants, in environmental compartments and biota. The wide variety of analyte/level/matrix/matrix property combinations available from several suppliers enables analysts to select CRMs which sufficiently match the properties of the samples they analyse routinely. Materials value-assigned for the so-called emerging pollutants are scarce at the moment, though an objective of current development programmes of CRM suppliers is to overcome this problem.     

Applicability of 0.05 mol kg potassium hydrogen phthalate as reference value pH standard in water–organic solvent mixtures

The applicability of 0.05 mol kg⁻¹ potassium hydrogen phthalate (KHPh(S), S=the solvent under study) as reference value pH standard (RVS) was studied in water–organic solvent mixtures. Phthalic acid in various aqueous organic solvent mixtures was titrated potentiometrically with Bu₄NOH (MeOH), using a pH-ISFET and a glass electrode as pH-sensors, and the buffer capacity of the HPh⁻ solution was roughly estimated from the difference between the first and second half-neutralization potentials. The influence of potassium ion to the buffer capacity was also studied, titrating KHPh and Et₄NHPh with CF₃SO₃H and Bu₄NOH (MeOH) and comparing the titration curves. The KHPh solution loses its buffer capacity if the solvent mixture has an aprotic property. For aqueous mixtures of protophilic aprotic solvents (e.g. DMSO and DMF), it is unsuitable as RVS if the water content is less than ca. 40 (v/v)%. The necessity of selecting subsidiary pH standard(s) is suggested for the solvent systems in which KHPh is inapplicable.     

A new river sediment standard reference material

The collection, processing and certification of a new sediment Standard Reference Material (SRM), SRM 2704, is described. Collected from the bottom of the Buffalo River in New York State during the fall of 1986, SRM 2704 is certified for 25 elements with information provided on another 22 elements. Improvements in analytical methods as well as the application of well-defined quality-control procedures for collection, processing and analysis have resulted in a reference material that is more completely characterized than previous NIST sediment reference materials.     

Analysis of urban particulate standard reference materials for the determination of chlorinated organic contaminants and additional chemical and physical properties

A previously issued National Institute of Standards and Technology (NIST) Standard Reference Material (SRM), SRM 1649, Urban Dust/Organics has been analyzed for chlorinated organic contaminants (polychlorinated biphenyls and chlorinated pesticides) to provide certified values for a new class of compounds relative to the former certification. The material will be reissued as SRM 1649a. Four different analytical techniques were used. Specifically, two different methods of extraction (Soxhlet and pressurized fluid extraction) were used in conjunction with sample analysis by gas chromatography with two different columns (5% phenyl-methyl polysiloxane and 50% methyl C-18 dimethyl polysiloxane) that exhibit distinct selectivity, and with two different modes of detection (electron capture detection and mass spectrometry). The results from these techniques were combined to generate certified concentrations for 35 PCB congeners (some in combination) and 8 chlorinated pesticides. Ancillary assessments of additional chemical and physical properties of SRM 1649a include homogeneity, moisture, total organic carbon, extractable mass, and the particle-size distribution. The approach and the results for the certification of the PCB congeners and chlorinated pesticides in SRM 1649a, and the determination of the additional chemical and physical properties are described. In addition, the determination of PCBs and chlorinated pesticides in SRM 1648, Urban Particulate Matter (a particulate material certified for inorganic constituents), is also discussed although certified values are not presented. Received: 8 June 1998 / Revised: 4 September 1998 / Accepted: 26 September 1998     

Analysis of urban particulate standard reference materials for the determination of chlorinated organic contaminants and additional chemical and physical properties

A previously issued National Institute of Standards and Technology (NIST) Standard Reference Material (SRM), SRM 1649, Urban Dust/Organics has been analyzed for chlorinated organic contaminants (polychlorinated biphenyls and chlorinated pesticides) to provide certified values for a new class of compounds relative to the former certification. The material will be reissued as SRM 1649a. Four different analytical techniques were used. Specifically, two different methods of extraction (Soxhlet and pressurized fluid extraction) were used in conjunction with sample analysis by gas chromatography with two different columns (5% phenyl-methyl polysiloxane and 50% methyl C-18 dimethyl polysiloxane) that exhibit distinct selectivity, and with two different modes of detection (electron capture detection and mass spectrometry). The results from these techniques were combined to generate certified concentrations for 35 PCB congeners (some in combination) and 8 chlorinated pesticides. Ancillary assessments of additional chemical and physical properties of SRM 1649a include homogeneity, moisture, total organic carbon, extractable mass, and the particle-size distribution. The approach and the results for the certification of the PCB congeners and chlorinated pesticides in SRM 1649a, and the determination of the additional chemical and physical properties are described. In addition, the determination of PCBs and chlorinated pesticides in SRM 1648, Urban Particulate Matter (a particulate material certified for inorganic constituents), is also discussed although certified values are not presented. Received: 8 June 1998 / Revised: 4 September 1998 / Accepted: 26 September 1998     

Determination of polybrominated diphenyl ethers in indoor dust standard reference materials

Polybrominated diphenyl ethers (PBDEs) have been measured for the first time in three different indoor dust Standard Reference Materials (SRMs) prepared by the National Institute of Standards and Technology (NIST). Two of these, SRM 2583 (Trace Elements in Indoor Dust) and SRM 2584 (Trace Elements in Indoor Dust), have been certified previously for lead and other inorganic constituents. A third, SRM 2585 (Organics in Indoor Dust), is a new indoor dust reference material prepared by NIST which will be certified for various organic compounds (polycyclic aromatic hydrocarbons, pesticides and polychlorinated biphenyls) in 2005 including certified concentrations for 16 individual PBDE congeners and reference values for an additional three PBDE congeners. Dust SRMs were analyzed for 30 PBDE congeners using high-resolution gas chromatography combined with low-resolution mass spectrometry operated in both negative chemical ionization (GC/ECNI–MS) and electron impact ionization (GC/EI–MS) modes. Sensitivity was an order of magnitude higher using GC/ECNI–MS relative to GC/EI–MS. These SRMs have been characterized and compared to the three PBDE commercial products (pentaBDE, octaBDE and decaBDE). PentaBDE and DecaBDE were present in all three SRMs and were the dominant commercial products, making up approximately 33% and 58%, respectively. Recent studies suggest that house dust may be a leading source of human exposure to PBDEs. These SRMs are the first reference materials with certified concentrations for PBDEs, which will aid in validating future measurements of PBDEs in house dust and other similar matrices. Electronic Supplementary Material Supplementary material is available for this article at http://dx.doi.org/ 10.1007/s00216-005-0227-y     

Determination of organic acids in Vaccinium berry standard reference materials

Nine organic acids (citric acid, galacturonic acid, glycolic acid, isocitric acid, malic acid, oxalic acid, quinic acid, shikimic acid, and tartaric acid) and two anions (phosphate and sulfate) were determined in a suite of Vaccinium berry-containing dietary supplement standard reference materials (SRMs). Following solvent extraction, three independent methods were utilized in the quantification of these compounds. The first method involved reversed-phase liquid chromatography with ultraviolet absorbance detection at 210 nm and isotope dilution mass spectrometry. The second method utilized ion chromatography with conductivity detection. Finally, gas chromatography with isotope dilution mass spectrometry detection was used following derivatization with N-methyl-N-trifluoroacetamide (MSTFA). The combined data from these methods was used for the assignment of organic acid levels in the seven candidate SRMs.     

Simultaneous extraction of di(2-ethylhexyl) phthalate and nonionic surfactants from house dust. Concentrations in floor dust from 15 Danish schools

Static extraction, supercritical fluid extraction (SFE), pressurized liquid extraction (PLE) and Soxhlet extraction were compared for simultaneous extraction of di(2-ethylhexyl) phthalate (DEHP) and nonionic surfactants from house dust. Homogenized office floor dust from a vacuum cleaner dust bag ("standard dust") was used for the evaluation. One portion of the extracts was used for analysis of nonionic surfactants with LC-MS and another portion was used for DEHP analysis with GC-MS. The extraction yield of DEHP was comparable for all the methods whereas SFE and PLE were the most efficient extraction techniques for the nonionic surfactants. The PLE extraction was found most suitable as a routine method for simultaneous extraction of both types of compounds and was used in a field study of floor dust from 15 Danish schools. The mean concentration of DEHP in the school dust samples was approximately 4 times higher than observed in other studies of dust from homes in different countries. The concentrations of nonionic surfactants were one order of magnitude lower than soap and linear alkylbenzene sulfonates measured in other studies of floor dust from offices and other public buildings. However, for the first time nonionic surfactants have been identified in house dust.     

Certified reference materials for organic contaminants in sewage sludge: a feasibility study

As an answer to the re-evaluation of the European sludge directive, two novel reference materials for organic components in municipal sludge have been produced and test certified for AOX (absorbable organic halogens), PAH (polycyclic aromatic hydrocarbons), NPE (nonylphenol and nonylphenolethoxylates), DEHP (di(2-ethylhexyl)phthalate), bisphenol A, and BFR (brominated flame retardants). The materials were prepared from raw sludge without spiking or mixing of different sludges. The study demonstrated that the technique for the preparation of a suitable reference material, sufficiently homogenous and stable, and with concentration levels that answer the needs of the laboratories and the relevant authorities, can now be presented in detail. The results, furthermore, show there is a need for method validation and standardisation of the measurements of NPEs and certain BFR congeners, and that the development of the laboratory structure in Europe, with fewer and more specialised laboratories, might become a major obstacle when trying to find a sufficient number of laboratories being appropriately proficient for this kind of study in the future.     

Determination of silver in SOIL-7 standard reference material by NAA

IAEA standard reference material SOIL-7 has been analyzed by both instrumental NAA and radiochemical NAA using epithermal neutron activation. These analyses confirm the NAA value of Ag in the intercomparison SOIL-7 which disagrees with some AAS values. Further geostandards were included and compared with literature data.     

Certification of a new NIST fly ash standard reference material

In June 1993 the National Institute of Standards and Technology (NIST) released the third version of Constituent Elements in Coal Fly Ash Standard Reference Material (SRM 1633b). This material is intended for quality assurance purposes in evaluating the analytical methods used for the determination of constituent elements in coal fly ash or in materials with similar matrices. It has been certified for 23 major, minor and trace elements using ten different analytical techniques. For an element to be certified in a NIST SRM, its concentration is usually determined by at least two independent analytical techniques. The concentrations of additional 24 elements are provided for information only purposes in the new fly ash. Current plans are to certify the concentrations of a number of rare earths upon completion of additional analytical work now in progress. Homogeneity testing was accomplished using instrumental neutron activation analysis and X-ray fluorescence. This presentation summarizes the preparation of this new material and the analytical results used for certification.     

Preparation and characterization of standard reference material 3276, carrot extract in oil

The National Institute of Standards and Technology (NIST), the Food and Drug Administration (FDA) Center for Drug Evaluation and Research (CDER) and Center for Food Safety and Applied Nutrition (CFSAN), and the National Institutes of Health (NIH), Office of Dietary Supplements (ODS) are collaborating to produce a series of standard reference materials (SRMs) for dietary supplements. Standard reference material (SRM) 3276 Carrot Extract in Oil is one in this series, with values assigned for trans-alpha-carotene, trans- and total beta-carotene, delta- and gamma-tocopherol, and twelve fatty acids. Results for carotenoids and tocopherols were obtained by use of combinations of liquid chromatography (LC), on columns of differing selectivity, with absorbance and mass spectrometric (MS) detection. Fluorescence detection also was used for the tocopherols. Results for fatty acids were obtained by use of gas chromatography (GC) with both flame-ionization and mass-spectrometric detection. This material is intended for use as a primary control material when assigning values to in-house (secondary) control materials and for validation of analytical methods for measurement of these analytes in similar matrices.     

Standard reference materials (SRMs) for determination of organic contaminants in environmental samples

For the past 25 years the National Institute of Standards and Technology (NIST) has developed certified reference materials (CRMs), known as standard reference materials (SRMs), for determination of organic contaminants in environmental matrices. Assignment of certified concentrations has usually been based on combining results from two or more independent analytical methods. The first-generation environmental-matrix SRMs were issued with certified concentrations for a limited number (5 to 10) of polycyclic aromatic hydrocarbons (PAHs) and polychlorinated biphenyls (PCBs). Improvements in the analytical certification approach significantly expanded the number and classes of contaminants determined. Environmental-matrix SRMs currently available include air and diesel particulate matter, coal tar, marine and river sediment, mussel tissue, fish oil and tissue, and human serum, with concentrations typically assigned for 50 to 90 organic contaminants, for example PAHs, nitro-substituted PAHs, PCBs, chlorinated pesticides, and polybrominated diphenyl ethers (PBDEs). Electronic supplementary material Supplementary material is available in the online version of this article at and is accessible for authorized users.