Design of single polarization single mode dispersion compensating photonic crystal fiber

In this paper, we present a photonic crystal fiber based on hexagonal structure for improved negative dispersion as well as high birefringence in the telecom wavelength bands. It is demonstrated that it is possible to obtain negative dispersion coefficient of −712 ps/(nm km) and relative dispersion slope (RDS) perfectly match to that of single mode fiber (SMF) of about 0.0036 nm⁻¹ at the operating wavelength 1550 nm. The proposed fiber exhibits high birefringence of the order 2.11 × 10⁻² with nonlinear coefficient about 57.57 W⁻¹ km⁻¹ at 1550 nm. Moreover, it is confirmed that the designed fiber successfully operates as a single mode in the entire band of interest.     

Deep ultraviolet femtosecond laser tuning of fiber Bragg gratings

A deep ultraviolet femtosecond laser operating at wavelength 258 nm was demonstrated to be effective in trimming fiber Bragg gratings in telecommunication fibers. A smooth tunable resonance wavelength shift of up to 0.52 nm has been observed, corresponding to a refractive index change of ∼5 × 10⁻⁴ after an accumulated laser fluence of 63.3 kJ/cm² at a single pulse fluence of 124 mJ/cm². The ultrafast laser enhancement of ultraviolet photosensitivity response and modification of anisotropic index profile in silica fiber is a powerful technique to precise control of the performance of fiber Bragg grating devices for applications in optical filtering and polarization mode dispersion management.     

Maintaining single polarization and dispersion compensation with modified rectangular microstructure optical fiber

In this paper, we propose and numerically demonstrate a highly birefringent microstructure optical fiber which shows negative dispersion coefficient of about −288 to −550 ps/(nm km) covering S to L wavelength bands and −425 ps/(nm km) at the excitation wavelength 1550 nm. This proposed design successfully compensate the dispersion covering S to L communication bands ranging from 1460 to 1625 nm along with relative dispersion slope (RDS) perfectly matched to that of single mode fiber of about 0.0036 nm⁻¹. Apart from dispersion compensation, the designed MOF offers high birefringence of 2.94 × 10⁻² at 1550 nm and better compensation ratio with design simplicity due to circular air-holes in the fiber cladding.     

High birefringence and low loss circular air-holes photonic crystal fiber using complex unit cells in cladding

We propose a high birefringence and low loss index-guiding photonic crystal fiber (PCF) using the complex unit cells in cladding by the finite-element method. Results show that the birefringence and confinement loss in such PCF fiber is determined not only by the whole cladding asymmetry but also the shape of the PCF core. The maximal modal birefringence and lowest confinement loss of our proposed structures at the excitation wavelength of λ = 1550 nm can be achieved at 8.7 × 10⁻³ and 5.27 × 10⁻⁵ dB/km, respectively.     

A novel double-Brillouin-frequency spaced multi-wavelength Brillouin erbium-doped fiber laser based on non-linear amplified fiber loop mirror

In the paper, a ring double-Brillouin-frequency spaced multi-wavelength Brillouin erbium-doped fiber laser based on non-linear amplified fiber loop mirror filter is demonstrated, in which the non-linear amplified fiber loop mirror (AFLMF) is used as a filter. At the 980 nm pump power of 10.29 dBm, the tunable laser source center wavelength of 1563 nm and power of −3 dBm, up to 12 even output channels with 0.16 nm spacing are achieved. At the same time, we study the influence of 980 nm pump power, the polarization controller and the tunable laser source center wavelength on the number of Stokes light wave.     

Design and analysis of a photonic crystal fiber with four-hole unit

A novel photonic crystal fiber (PCF) based on a four-hole unit is proposed in order to meet the requirements of high birefringence, negative dispersion and confinement loss in fiber-optic communication. The proposed design has been simulated based on the full vector finite element method (FVFEM) and anisotropic perfectly matched layers (APML). Analysis results show that the proposed PCF can achieve a high birefringence to the order of 10⁻² at the wavelength of 1.55 μm, a large negative dispersion over a wide wavelength range and confinement losses lower than 10⁻⁹ dB/m simultaneously, which has important applications in polarization-maintaining (PM) fibers, single-polarization single-mode (SPSM) fibers, dispersion compensation fibers and so on.     

Simultaneous measurement of curvature and temperature based on PCF-based interferometer and fiber Bragg grating

A sensor head consisting of a photonic crystal fiber (PCF)-based Mach-Zehnder interferometer (MZI) and a fiber Bragg grating (FBG) is proposed and experimentally demonstrated for simultaneous measurement of curvature and temperature. The MZI fabricated by splicing a short length of PCF between two single-mode fibers with the air-hole structure that completely collapsed near the splicing points, is sensitive to fiber bending and surrounding temperature, while the FBG is only sensitive to the later. Simultaneous measurement of curvature and temperature is therefore obtained. Sensitivities of 4.06 nm/m^− 1 and 6.30 pm/°C are achieved experimentally for curvature and temperature, respectively. And the corresponding resolutions are 5.2 × 10^− 4 m^− 1 and 1.25 °C for curvature and temperature, respectively, based on the wavelength measurement resolution of 10 pm.     

输出平均功率大于2W的高功率、包层抽运、超短脉冲铒镱共掺光纤激光器

采用主振荡功率放大的方式，研制成功集宽带波长连续可调谐、带宽内输出功率谱均衡、高重复频率和高功率性能于一体的超短脉冲包层抽运铒镱共掺光纤激光器.将优化主振荡器和功率放大器的腔结构与掺铒光纤的饱和增益特性结合起来，实现了1535nm—1570nm(35nm带宽)的输出功率均衡的波长连续可调谐激光输出，在带宽内激光功率的最大波动仅为0.5dBm；带宽内平均输出功率大于2W、脉冲重复频率大于10GHz、脉冲宽度小于30ps.该激光器具有综合性能指标先进、结构简单、全光纤化、使用方便等优点. 关键词： 光纤激光器 包层抽运 短脉冲 高重复频率     

Design and characterization of single mode circular photonic crystal fiber for broadband dispersion compensation

In this paper, we present a single mode circular photonic crystal fiber (C-PCF) for broadband dispersion compensation covering 1400 to 1610 nm wavelength band over the telecommunication windows. Investigations of guiding properties are carried out using finite element method (FEM) with circular perfectly matched layer boundary condition. Numerical study reveals that a negative dispersion coefficient of about −386.57 to −971.44 ps/(nm km) is possible to obtain over the wavelength ranging from 1400 to 1610 nm with a relative dispersion slope (RDS) of about 0.0036 nm⁻¹ at 1550 nm wavelength. In addition, the single mode behaviour of C-PCF is demonstrated by employing V parameter. According to simulation, it is found that the proposed C-PCF acts as a single mode fiber within 1340 to 1640 nm wavelength. Moreover, effective dispersion, relative dispersion slope, birefringence and confinement loss are also presented and discussed.     

Tunable wavelength conversion of picosecond pulses based on cascaded sum- and difference-frequency generation in quasi-phase-matched LiNbO3 waveguides

Tunable wavelength conversion for picosecond pulses is proposed and demonstrated exploiting cascaded sum- and difference-frequency generation in quasi-phase-matched LiNbO₃ waveguides. The influences of initial pulse widths and injected pulse powers on the conversion efficiency and converted pulse width are theoretically analyzed. Arbitrarily tunable wavelength conversion is performed for the signal pulse with the temporal width of 1.57 ps and repetition rate of 40 GHz. Approximately −18.9 dB conversion efficiency and 25 nm variable region of the input signal are achieved under the lower launched signal power. The results imply that simultaneous wavelength conversion and pulse compression can be potentially obtained by using the pulsed control wave or designing longer waveguides.     

Giga-bit optical receiver for plastic optical fibre

An optical receiver with high sensitivity and linearity specially designed for Giga-bit communications over small-bandwidth high-attenuation multimode plastic optical fiber is presented. An automatic gain control transimpedance amplifier and linear post amplifiers are used to maintain a good performance with multilevel modulation. Using multilevel signaling and large-diameter integrated photodiodes make the presented optical receiver suitable for large core plastic optical fiber. For a wavelength of 675 nm, a sensitivity of −26.3 dB m (BER = 10⁻⁹) at 500 Mb/s is presented by a binary signal. A data rate of 1 Gb/s and a sensitivity of −19.8 dB m (BER = 10⁻⁹) are achieved with four-level pulse amplitude modulation.     

Simultaneous measurement of strain and temperature with a long-period fiber grating inscribed Sagnac interferometer

A Sagnac interferometer with a long-period fiber grating (LPG) inscribed in the polarization-maintaining fiber (PMF) is proposed and experimentally demonstrated for simultaneous measurement of strain and temperature. Due to the different responses of the LPG and the Sagnac interferometer to strain and temperature, simultaneous measurement can be achieved by monitoring the wavelength shifts and the intensity changes of a resonance dip of the sensor setup. The experimental results show that the achieved sensitivities to strain and temperature are 6.4 × 10^− 3 dB/με and 0.65 nm/°C, respectively.     

Tunable 19 × 10 GHz L-band FP-SOA based multi-wavelength mode-locked fiber laser

We present a multi-wavelength mode-locked fiber ring laser incorporating a semiconductor optical amplifier (SOA) and a Fabry-Perot semiconductor optical amplifier (FP-SOA). Because the gain of the SOA is depleted by an external injection optical signal, the SOA acts as a loss modulator. The FP-SOA serves as a tunable comb filter. The presented laser source can generate 19 synchronized wavelength channels with the extinction ratio of about 21 dB, each mode-locked at 10 GHz, and mode-locked pulse width is about 40 ps. Oscillation wavelengths band can be tuned by adjusting the bias current of the SOA, and wavelength spacing also can be changed by using a tunable optical delay line (ODL) or a temperature controller. The polarization-insensitive devices ensure that the output power is rather stable. This fiber laser has potential applications in longer waveband (L-band) within the low-attenuation window.     

Design and analysis of novel octagonal photonic crystal fiber with F-doped elliptical hole core

A design of octagonal photonic crystal fiber (OPCF) with F-doped elliptical hole core is proposed. The proposed design is simulated through an full vector finite element method (FVFEM) and anisotropic perfectly matched layers (APML). Numerical results show that the designed OPCF has the ultra-flattened dispersion of 0 ± 0.4 ps/(nm km) from 1.34 μm to 1.72 μm (380 nm band) which covers S, C and L communication bands, a low confinement loss of less than 10⁻⁷ dB/m in the same wavelength range, and the corresponding birefringence and nonlinear coefficient are about 2.12 × 10⁻² and 50.67 W⁻¹ km⁻¹ at 1.55 μm, respectively. The proposed OPCF may have great potential applications in super-continuum (SC) generation, dispersion compensation, polarization maintaining and so on.     

Tunable all-fiber intracavity wavelength converter without external pumps

A new architecture for tunable broadband wavelength conversion in a dispersion-shifted fiber is presented. Conversion is achieved by using four-wave-mixing in a dispersion-shifted fiber in a single fiber-ring cavity. Wide tunability is achieved by the self-generation of two tunable orthogonal pumps in the cavity. This effect is due to the introduction of two tunable fiber Bragg gratings written in high birefringence fibers which act as selective polarization and wavelength filters. The results show conversion efficiencies up to −2 dB with the signal-to-noise ratio of the converted signal up to 26 dB.     

Photonic crystal fiber with high birefringence and low confinement loss

In this paper, a highly birefringent index-guiding photonic crystal fiber with low confinement loss is proposed by enlarging the central row of air holes in the structure. By employing the multipole method, properties of this structure, including the effective index, birefringence and confinement loss, are investigated. Simulation results indicate that high birefringence of 1.65 × 10⁻³ can be reached at the wavelength of 1.55 μm, and a low confinement loss on the order of 10⁻⁶ dB/km can be achieved at the same wavelength. Moreover, the impacts of air hole sizes on birefringence and confinement loss are also analyzed in detail.     

Broadband Er-Yb co-doped superfluorescent fiber source

In this paper, extensive experimental results on broad-band double cladding Er³⁺-Yb³⁺ co-doped superfluorescent fiber sources (SFSs), characterizing their output power, mean wavelength, and bandwidth (BW) stability with variations of pump power, pump wavelength, and fiber temperature, have been reported. For a 55-cm fiber, SFS power from 3.7755 (maximum BW condition of more than 80 nm) to 9.1837 mW (maximum power condition, BW is about 34 nm) has been achieved. The SFS mean wavelength dependence on pump wavelength is highly pump temperature sensitive, and can be reduced to zero in a chosen pump temperature field. The intrinsic variation of the SFS mean wavelength λ_m with fiber temperature is also measured, and a linear variation from 15 to 45 °C with a slop of −0.053 nm/°C for L_f = 100 cm and −0.04 nm/°C for L_f = 55 cm is found.     

Highly birefrigent photonic crystal fiber with high negative dispersion for broadband dispersion compensation

In this paper, we proposed a dual-enhanced core photonic crystal fiber (PCF) with high birefringence and ultra-high negative dispersion for dispersion compensation in a polarization maintained optical system. Using finite difference time domain (FDTD) method, we presented dispersion compensating PCF (DC-PCF) with negative dispersion between −1650 ps nm⁻¹ km⁻¹ and −2305 ps nm⁻¹ km⁻¹ in C-band and particularly −2108 ps nm⁻¹ km⁻¹ in λ = 1.55 μm wavelength. By this method, we can compensate dispersion in 124 km long span of a conventional single mode fiber (SMF) by 1 km-long of the DC-PCF at λ = 1.55 μm wavelength. Moreover, fundamental mode of the proposed PCF can induce birefringence about 3.5 × 10⁻³ at 1.55 μm wavelength.     

All-optical RZ-to-NRZ data format conversion using spectral broadening effect in a dispersion-shifted fiber

We propose a simple and efficient approach to obtain all-optical RZ-to-NRZ data format conversion using self-phase modulation (SPM) in a dispersion-shifted fiber. By exploiting SPM induced spectral broadening together with group velocity dispersion in the normal regime, a 10 Gb/s return-to-zero data signal has been converted to the non-return-to-zero format. The proposed scheme can work with different signal bit rates and does not require any external pulse duplicator. The 10 Gb/s bit-error-rate (BER) measurement shows a power penalty of less than 1.5 dB at 10⁻⁹ BER level.     

Designing of endlessly single mode polarization maintaining highly birefringent nonlinear micro-structure fiber at telecommunication window by FV-FEM

An endlessly single mode highly polarization maintaining nonlinear microstructure fiber at telecommunication window is reported via full-vector finite element method. By taking three ring hexagonal PCF with suitable fiber parameter such as air hole diameter in cladding region d = 0.8 μm, pitch 2.3 μm and introducing four symmetrical large air holes near core region d′ = 2 μm, single mode (V_eff ≤ π), small effective mode area 2.7 μm², nonlinear co-efficient 44.39 W⁻¹ km⁻¹, high phase birefringence of the order of 10⁻³ and group birefringence of the order of 10⁻⁴ with beat length 0.3 μm at wavelength 1.55 μm are achieved.