Stopping and storing light pulses within a fiber optic ring resonator

A simple all optical system for stopping and storing light pulses is demonstrated. The system consists of an erbium-doped fiber amplifier （EDFA）, a semiconductor optical amplifier （SOA）, and a fiber ring resonator. The results show that the multisoliton generation with a free spectrum range of 2.4 nm and a pulse spectral width of 0.96 nm is achieved. The memory time of 15 min and the maximum soliton output power of 5.94 dBm are noted, respectively. This means that light pulses can be trapped, i.e., stopped optically within the fiber ring resonator.     

基于半导体光放大器的可调谐多波长光纤激光器

报道了一种新型环形腔可调谐多波长光纤激光器,腔内以半导体光放大器为增益介质,利用高双折射光纤构成的高双折射环形镜的滤波特性,在室温下,获得了基本符合ITU-T标准100GHz的17个波长以上的稳定多波长输出.各信道峰值功率差小于6 dB,线宽小于0.102 nm,信噪比大于25 dB.通过调节高双折射环形镜内的偏振控制器状态实现了这一组波长整体在50GHz范围内连续可调谐.并利用实验方法,对该光纤激光器应用于掺铒光纤放大器对多信道放大性能测试的可行性进行了初步探讨.     

Performance Evaluation and Characterization of Hybrid Optical Amplifiers for Dwdm Systems at Ultra Narrow Channel Spacing

We study hybrid optical amplifiers (HOAs) for dense wavelength division multiplexed (DWDM) systems at reduced channel spacing (<0.2 nm). The Raman erbium-doped fiber amplifier (EDFA) (R-E) and EDFA-semiconductor optical amplifier (SOA) (E-S) hybrid optical amplifiers (HOAs) are investigated for the first time at 0.05 and 0.1 nm of the channel spacing. We show that the R-E HOA provides better gain (23.9 dB) and induces lesser crosstalk (-14.1 dB) with minimum utilization of the bandwidth. We report that 70 km is the optimum span distance at which the R-E HOA achieves a 2450 km transmission distance with acceptable performance. The theoretical results are found to be in accordance with numerical simulations in terms of the amplifier gain and induced crosstalk.     

混合泵浦两段级联掺铒光纤放大器实验研究

基于内插隔离－耦合环两段级联新结构，采用９８０ｎｍ与１４８０ｎｍ激光二极管混合泵浦方式，研制出在１．５５μｍ波段兼具高增益，大功率，低噪声九特性的掺铒光纤放大器。     

Eleven-wavelength switchable fiber ring laser with a dispersion compensation fiber and a delayed interferometer

We demonstrate a fiber ring laser with a dispersion compensation fiber (DCF) and a delayed interferometer (DI) with temperature control, which is able to switch eleven wavelengths one by one. In ring cavity, DCF supplies different effective cavity lengths for different wavelengths, DI generates a wavelength comb corresponding to the ITU grid, a flat-gain erbium-doped fiber amplifier (EDFA) provides uniform gain for each lasting wavelength, and a semiconductor optical amplifier (SOA) not only acts as active modulator, but also alleviates homogeneous broadening effect of EDFA. Stable pulse trains with a pulsewidth about 40 ps at 10 GHz have been obtained by injecting external optical control signals into the laser. Wavelength switching process among eleven wavelengths is achieved by merely tuning an intracavity optical delay line.     

Simulative investigation the impact of optical amplification techniques on single- and dual-electrode MZM and direct modulator's in single-tone RoF system

Since the introduction of erbium-doped fiber amplifier (EDFA) in optical fiber communication systems at 1550 nm, the fiber loss is no longer considered as the limiting factor but the fiber dispersion and chirp parameters play an important role in degrading the performance of optical communication systems. Further, the invention of external modulators of Mach-Zehnder (MS) type minimizes the transmission power penalty due to fiber chromatic dispersion as these modulators are consider almost chirp-free modulators. Also, better suppression of nonlinear distortions consists of harmonic distortions (HDs) and intermodulation distortions (IMDs) were achieved by using Mach-Zehnder external modulator [8]. In this work, a simulation comparison of external- and direct-modulation schemes using different optical amplifiers; SOA and EDFA in single-tone RoF system is reported. A single-tone channel of 20 GHz is transmitted over single-mode fiber (SMF) either externally modulated by using single-electrode (SEMZM) - and dual-electrode (DEMZM) - Mach-Zehnder modulator or by direct-modulation scheme. Better improvements in the measurement of received RF power of a 20 km linked single-tone RoF system are achieved by using SEMZM with EDFA, which means maximum optical link is achieved between Central Office (CO) and Base Station (BS). Further, this scheme provides better BER as compare to other schemes discussed in this paper.     

Multiwavelength fiber laser using S-band erbium-doped fiber amplifier and semiconductor optical amplifier

A multiwavelength fiber ring laser that is based on an S-band erbium-doped fiber amplifier (EDFA) and a semiconductor optical amplifier (SOA) is developed. An optical switch is used to switch the multiwavelength fiber laser between S-band and L-band. This fiber laser can stably lase seven wavelengths in the S-band or 28 wavelengths in the L-band. Additionally, the lasing wavelengths with a signal-to-noise ratio of over 33 dB and a wavelength spacing of 100 GHz are demonstrated experimentally. The average powers of the lasing wavelength in the S-band and the L-band are −7.53 and −12.15 dBm, respectively.     

Remotely Pumped Hybrid Amplifiers for Extended Bidirectional Passive Optical Networks

In this contribution, we optimize design parameters of hybrid optical amplifiers utilizing distributed Raman amplification in transmission fiber and gain of discrete, remotely pumped erbium-doped fiber amplifier (EDFA) for wideband, bidirectional operation in metropolitan area networks (MAN). The design is based on an application of a numerical model, which takes into account pump-to-pump and signal-to-signal interactions and generation of amplified spontaneous emission in the Raman amplifier and solves the standard rate-propagation equations in an erbium-doped fiber (EDF). We predict 12 dB gain across 72 nm of optical bandwidth with gain ripple better than 10%. The recently proposed serial topology of EDFA is considered; this enables the wideband, bidirectional operation of a hybrid amplifier with only two pump laser diodes emitting in the 1430 and 1480 nm bands.     

有源循环式光脉冲复制系统的输出特性研究

改进并验证了一种基于有源循环光纤延迟线的模拟光脉冲信号复制技术.实验系统采用低增益掺铒光纤放大器补偿循环损耗.进行了光脉冲信号复制的仿真和实验,在掺铒光纤放大器增益为6.774 dB,光滤波器－3 dB,带宽为0.8 nm时,测得第500个复制光脉冲的信噪比为31 dB.仿真和实验结果表明,选用小增益掺铒光纤放大器可以实现低于3 dB的噪音系数,降低掺铒光纤放大器的放大自发辐射噪音并提高输出脉冲序列的信噪比,有望成为提高光脉冲复制器性能的一种新方法.在系统中插入窄带光滤波器等手段也是改善信噪比的有效措施.     

包含两个半导体光放大器的锁模光纤环形激光器数值研究

采用自再现理论,对一种包含两个半导体光放大器的锁模光纤环形激光器进行了数值研究.研究结果表明：为了提高谐波锁模输出脉冲的质量,调制半导体光放大器应当保持高直流偏置,对自发辐射信号进行调制并提供锁模脉冲克服腔损耗所需的增益,而此时的增益半导体光放大器则被低直流偏置充当增益补偿器维持较窄的净增益窗口;与之相反,为了获得振幅均衡的有理数谐波锁模输出脉冲,调制半导体光放大器则应当偏置在较低的电流上,而增益半导体光放大器应当保持较高的偏置电流以提供足够的常量增益克服腔损耗.此外,还必须提高注入光信号的峰值功率.     

Multiple Parameters Optical Sensing Using Fiber Ring Laser Based on Fiber Bragg Gratings and 1064 nm Semiconductor Optical Amplifier

Optics and Spectroscopy - In this paper, a semiconductor optical amplifier (SOA) based 1064 nm fiber ring laser with 63.56&nbsp;dB optical signal-to-noise ratio (OSNR) is demonstrated. The...     

A global design of an erbium-doped fiber and an erbium-doped fiber amplifier

A global design of an erbium-doped fiber and an open-loop erbium-doped fiber amplifier (EDFA) in a steady-state operation is discussed by applying genetic algorithms. Taking a signal gain and a bandwidth as objective functions, 7 parameters of the EDFA (erbium concentration, core radius, erbium-doped radius, refractive index difference, fiber length, pumping wavelength and signal power) are optimized by solving optical propagation equations, assuming a homogenous two-level active medium and a single-mode propagation. There is evidence to show that the 1480 nm pump utilized in usual EDFAs is not an optimal choice, which should be chosen around 1460 nm. The optimal core radius ranges 0.465–0.548 μm on pumping power 50–200 mW. Under different design objects and with different pumping powers, however, there are different optimal Er-doped concentrations, reflective index differences and fiber lengths. As a single fiber EDFA, 35 dB signal gain or 35 nm bandwidth is obtained with the 7 optimal parameters, 100 mW pumping power and 0.001 mW input signal power.     

Temperature independent length optimization of L-band EDFAs providing flat gain

In this study, single stage (SS), double-stage (DS), and gain flattened (GF) DS L-band erbium-doped fiber amplifier (EDFA) configurations are designed in order to obtain a flat gain amplifier. Temperature dependence of the mentioned configurations is also analyzed. Maximum spectral dependence of EDFA gain with respect to temperature is obtained for SS EDFA design while smaller spectral dependence of gains is obtained for both DS and GF DS L-EDFA configurations. It is observed that the maximum temperature dependence is in the range of 1570-1580 nm band for all configurations. It has also been found that for all configurations, reducing the temperature has greater effect than raising the temperature on EDFA gain. The overall results show that a temperature independent L-band configuration has not been possible. However, for some signal wavelengths, the erbium-doped fiber (EDF) lengths at which the gain is temperature independent are observed.     

Long-distance fiber Bragg grating sensor system with a high optical signal-to-noise ratio based on a tunable fiber ring laser configuration

A novel tunable fiber ring laser configuration with a combination of bidirectional Raman amplification and dual erbium-doped fiber (EDF) amplification is proposed for realizing high optical signal-to-noise ratio (SNR), long-distance, quasi-distributed fiber Bragg grating (FBG) sensing systems with large capacities and low cost. The hybrid Raman-EDF amplification configuration arranged in the ring laser can enhance the optical SNR of FBG sensor signals significantly owing to the good combination of the high gain of the erbium-doped fiber amplifier (EDFA) and the low noise of the Raman amplification. Such a sensing system can support a large number of FBG sensors because of the use of a tunable fiber Fabry-Perot filter located within the ring laser and spatial division multiplexing for expansion of sensor channels. Experimental results show that an excellent optical SNR of approximately 60 dB has been achieved for a 50 km transmission distance with a low Raman pump power of approximately 170 mW at a wavelength of 1455 nm and a low EDFA pump power of approximately 40 mW at a wavelength of 980 nm, which is the highest optical SNR achieved so far for a 50 km long FBG sensor system, to our knowledge.     

Gain-clamping in two-stage L-band EDFA using an unwanted backward ase from second stage

A gain clamping technique for the long wavelength band erbium-doped fiber amplifier (L-band EDFA) is presented. It uses two circulators and a broad band fiber Bragg grating to route wasted backward C-band ASE from the second stage and launch it back into the input end of the first stage of a two-stage amplifier. The two-stage L-band EDFA has shown a small signal gain improvement of 5.7 dB compared to a single-stage amplifier with a slight noise figure degradation. By utilizing the wasted backward ASE, a L-band gain-clamped EDFA with high gain can be realized. Compared to the unclamped case, this gain-clamping technique is effective in reducing the total gain variation as small as 0.3 dB.     

用楔形柱面光纤微透镜耦合的1.3μm SOA组件

运用激光模式耦合理论分析了半导体光放大器(SOA)与单模通信光纤的连接损耗,并设计制作了楔形柱面光纤微透镜用来实现两者的模斑匹配,有效地降低了器件的光耦合损耗.本文介绍了楔形柱面光纤微透镜耦合的1.3 μm半导体光放大器(SOA)组件及其制作方法.该组件的最大增益不小于14 dB,其偏振灵敏度小于1 dB,增益波动不大于0.5 dB.     

Novel split-band erbium-doped fiber amplifier

In this paper we design a 120 nm bandwidth erbium-doped fiber amplifier using a seed light injection method for the first time. It is shown that when the wavelength of the seed light varies from 1520 to 1570 nm, the gain at 1610 nm reaches maximum near 1553 nm and increases as the seed light power. Based on the method, a novel split-band EDFA configuration is designed. The split-band architecture employs a 1550/1610 nm waveband multiplexer/demultiplexer and two independent sub-bands which pass in parallel through separate branches of the optical amplifier. The signals at independent sub-bands are combined and flattened before output, resulting in a broadband gain-flattened optical amplifier with 120 nm bandwidth.     

A Novel Method for Wavelength Conversion with Dual-pump Four-wave Mixing in a Semiconductor Optical Amplifier

1　Ｉｎｔｒｏｄｕｃｔｉｏｎ　　ＩｎｔｈｅＷＤＭｎｅｔｗｏｒｋ ,ｔｈｅｄｅｓｉｒａｂｌｅｆｅａｔｕｒｅｓｏｆａｎａｌｌ ｏｐｔｉｃａｌｗａｖｅｌｅｎｇｔｈｃｏｎｖｅｒｔｅｒｉｎｃｌｕｄｅｐｏｌａｒｉｚａｔｉｏｎｉｎｓｅｎｓｉｔｉｖｉｔｙ ,ｔｒａｎｓｐａｒｅｎｃｅｔｏｍｏｄｕｌａｔｉｏｎｆｏｒｍａｔａｎｄｂｉｔ ｒａｔｅ ,ｆｕｌｌｔｕｎａｂｉｌｉｔｙ ,ａｃｃｅｐｔａｂｌｅｏｕｔｐｕｔＳＮＲｏｖｅｒｔｈｅｅｎｔｉｒｅｒａｎｇｅｏｆｔｈｅｗａｖｅｌｅｎｇｔｈｓｕｓｅｄｉｎｔｈｅｎｅｔｗｏｒｋ[1] .Ｗａｖｅ…     

超宽带可调谐SOA四波混频波长变换器的实验研究

基于半导体光放大器(SOA)光纤环形激光器中的双泵浦四波混频效应,构成超宽带并且完全透明的波长变换器,成功实现1550nm窗口2.5Gb/s信号的可调谐波长变换,变换效率在50nm范围内保持基本平坦,同时测出了SOA增益和自发辐射(ASE)噪音功率的关系.实验结果表明,在一定限制条件下,提高泵浦功率可以提高变换信号的信噪比.     

Investigation of Hybrid Optical Amplifiers for Dense Wavelength Division Multiplexed System with Reduced Spacings at Higher Bit Rates

Abstract

This article proposes various combinations of optical amplifiers for a dense wavelength division multiplexed system and investigates the impact of reduced channel spacing at high bit rates in terms of quality factor, bit error rate, eye closure, and output power. It is reported that the hybrid optical amplifier (Raman–erbium-doped fiber amplifier [EDFA]) provides better results with a maximum covered single span distance (220 km) at channel spacing of 6.25 GHz. The maximum acceptable bit rate for the 12.5-GHz channel spacing dense wavelength division multiplexed system is also investigated, and the recommendation is provided that for the Raman–EDFA, Raman–EDFA–Raman, EDFA–Raman–EDFA, and EDFA–semiconductor optical amplifier–EDFA, the operating bit rate should not be greater than 20, 16, 19, and 20 Gbps, respectively.