液相色谱-质谱法同时测定塑料制品中的双酚A和四溴双酚A

建立了高效液相色谱-质谱同时测定塑料制品中的双酚A(BPA)和四溴双酚A(TBBP-A)的方法。采用超声波萃取技术萃取样品。系统地考察了前处理条件、色谱条件和质谱参数。实验表明,在50 ℃条件下,加入20 mL二氯甲烷对塑料样品中的BPA和TBBP-A超声提取60 min可获得较好的提取效果。以甲醇和水为流动相,采用液相色谱-质谱联用分离和检测BPA和TBBP-A。该方法的线性范围为0.1～2.0 mg/L; BPA和TBBP-A检出限分别为0.01 mg/kg和0.02 mg/kg;回收率为85.4%～97.6%。该方法分离时间短,操作简便,实用性强,灵敏度高,适用于塑料制品中双酚A和四溴双酚A的残留分析。     

高效液相色谱法测定建筑用胶黏剂中的游离苯酚

建立了建筑用胶黏剂中游离苯酚的高效液相色谱测定方法。对提取方法、色谱条件及检测波长的选择进行了研究。结果表明,采用甲醇超声提取样品15 min可获得良好的提取效果,该方法的定量限(LOQ,以信噪比为10计)为10 mg/kg,线性范围为0.5～100 mg/L,相关系数为0.999 9。在1倍LOQ、2倍LOQ、10倍LOQ添加水平下平均回收率在89.28%～99.27%之间。实际样品测定结果表明,双酚A型环氧树脂存在游离苯酚残留的风险。     

超高效液相色谱-质谱法测定环氧树脂粘结剂中双酚A

提出了环氧树脂粘结剂中双酚A的超高效液相色谱-质谱测定方法。样品用乙醇超声提取后,离心分离,取上清液过0.22μm有机滤膜,滤液经ZORBAX SB-C18色谱柱分离,用不同比例的水和乙腈的混合溶液作为流动相梯度淋洗,采用电喷雾负离子源,多反应监测模式。双酚A的质量浓度在2～1 000μg.L-1范围内与其峰面积呈线性关系,测定下限(10S/N)为0.5mg.kg-1。以空白环氧树脂粘结剂为基体,进行加标回收试验,测得回收率在89.3%～93.2%之间,测定值的相对标准偏差(n=6)在1.8%～3.3%之间。     

玩具中苯酚和双酚A的高效液相色谱-荧光检测方法研究

采用高效液相色谱分离,荧光检测器检测,建立了三种不同类型的玩具中苯酚和双酚A的测定方法.用超声提取的方式处理样品,对提取溶剂和提取时间进行选择,确定以甲醇-水(65:35,V/V)作为提取溶液,超声提取20 min.苯酚和双酚A分别在0.012～1.0 mg/L、0.03～2.5 mg/L范围内线性良好,相关系数均达到0.9999,检出限分别为0.6 mg/kg和1.5 mg/kg,不同加标水平的回收率为90.5%～104.3%,其相对标准偏差为0.4%～3.8%.该方法操作简便,灵敏度高、重现性好,能有效提取和测定三类玩具中的苯酚和双酚A.     

磁性石墨烯分散固相萃取结合液相色谱-串联质谱法测定水基胶中的双酚A和烷基酚

建立了超高效液相色谱-串联质谱(UPLC-MS/MS)与磁性石墨烯相结合测定水基胶中双酚A、壬基酚和辛基酚的方法。样品提取后,以磁性石墨烯分散固相萃取净化,经BEH C18色谱柱分离。分析物的回收率在81.5%～97.9%之间,日间相对标准偏差(RSDs)小于8.0%。所有化合物均获得了良好的线性系数(r≥0.9996),检出限(LOD)和定量限(LOQ)范围分别为3～8μg/kg和10～26μg/kg。采用该方法对20个水基胶实际样品进行检测,仅有1个样品检出4-正壬基酚。该方法可用于测定水基胶中双酚A和4种烷基酚的含量。     

气相色谱-质谱法测定奶瓶中双酚A含量

提出了气相色谱-质谱法测定奶瓶中双酚A含量的方法。取剪碎的样品经二氯甲烷溶解,甲醇提取后,所得净化液中双酚A与N,O-双(三甲基硅烷基)三氟乙酰胺-三甲基氯硅烷(99+1)溶液进行衍生化反应,产物用乙酸乙酯定容。在气相色谱分离中用DB-5MS毛细管柱为固定相,在质谱分析中采用选择离子监测模式。双酚A的质量浓度在10.0～200.0μg·L-1范围内与峰面积呈线性关系,测定下限(10S/N)为1.0mg·kg-1。方法用于奶瓶中双酚A的测定,回收率在77.5%～95.1%之间,相对标准偏差(n=6)为3.9%。     

液相色谱-串联质谱法同时测定纺织品和食品包装材料中的壬基酚、辛基酚和双酚A

建立了纺织品和食品包装材料中壬基酚、辛基酚和双酚A的液相色谱-串联质谱分析方法。不同类型的纺织品和食品包装材料样品采用加速溶剂萃取法,以无水乙醇为提取剂,在10.3 MPa和120℃下静态循环提取2次,提取液经Supelclean Envi-Carb石墨化碳黑固相萃取柱净化,收集甲醇-二氯甲烷(1∶4,V/V)洗脱液,采用Waters XBridge C18色谱柱,以甲醇-0.1%氨水溶液为流动相,梯度洗脱分离后,在LC/MS/MS多反应监测模式下进行定性与定量分析。壬基酚、辛基酚和双酚A的方法检出限为0.5μg/kg,在0.5～10μg/kg的3个添加水平范围内,纺织品样品的平均回收率为86.9%～92.5%,相对标准偏差均小于9.1%;食品包装材料样品的平均回收率为87.8%～93.0%,相对标准偏差均小于8.8%。本方法准确、快速、灵敏度高,可用于纺织品和食品包装材料的实际检验。     

气相色谱-质谱法分析食品包装材料中双酚A

建立了气相色谱-质谱联用技术测定食品包装材料中双酚A(BPA)的分析方法.经过对影响双酚A提取条件的优化,实验选用甲醇索氏提取法.方法的线性范围是0.5～2000μg/L;检出限为0.3μg/L;RSD为4.5%.此方法已用于多种日常食品包装材料中双酚A的测定.     

羧基化多壁碳纳米管固相萃取-液相色谱-串联质谱法测定环境水体中四溴双酚A和双酚A

建立了羧基化碳纳米管固相萃取-液相色谱-串联质谱联用检测环境水体中四溴双酚A和双酚A的方法。比较了多壁碳纳米管、C60和羧基化多壁碳纳米管作为固相吸附剂对水体中四溴双酚A和双酚A的吸附效率。固相萃取浓缩后的样品经Thermo Scientific Hypersil C18色谱柱（150 mm×4.6 mm,3 μm）分离,采用串联质谱负离子模式进行检测。结果表明,四溴双酚A和双酚A在0.02~1.0 mg/L范围内具有良好的线性关系（r²≥0.99）,空白样品中的检出限（S/N=3）分别为0.04 μg/L和0.2 μg/L。将所建立的方法应用于实际环境水体中四溴双酚A和双酚A的检测,添加回收率在82%~99%之间,精密度小于5.0%,该方法可用于复杂环境样品中痕量四溴双酚A和双酚A的检测。     

高效液相色谱法对纺织品和食品包装材料中的壬基酚、辛基酚和双酚A的同时测定

建立了高效液相色谱-二极管阵列检测器(DAD)/荧光检测器(FLD)串联技术同时测定纺织品和食品包装材料中壬基酚、辛基酚和双酚A的方法.实验样品采用加速溶剂萃取法,以无水乙醇为提取溶剂,在10.3 MPa和120 ℃下静态循环提取2次,提取液经Supelclean Envi-Carb石墨化碳黑固相萃取柱净化,以Agilent Zorbax SB-Phenyl(250 mm×4.6 mm,5 μm)色谱柱分离后用DAD-FLD串联法进行检测.壬基酚、辛基酚和双酚A的DAD检测波长为225 nm;荧光激发波长为227 nm,发射波长为315 nm.在25、50、500 μg/kg的添加水平下,纺织品样品和食品包装材料样品的平均回收率均为93% ～98%,相对标准偏差分别为2.8% ～7.0%和2.9% ～6.9%.方法准确、简便、快速,可用于纺织品和食品包装材料的实际检验工作.     

双酚A分子印迹聚合物为萃取介质搅拌饼固相萃取的制备及其萃取性能研究

以双酚A为模板,4-乙烯基吡啶为单体,利用整体材料"原位"聚合技术制备分子印迹聚合物为基质的萃取饼,并与利用一次性注射器空管加工而成的萃取器相结合,建立了分子印迹搅拌饼固相萃取(MIP-SCSE)技术。考察了制备条件对MIP-SCSE选择吸附性能的影响。在此基础上,与高效液相色谱-二极管阵列检测器联用,探讨MIP-SCSE对环境水样中双酚A及其它酚类物质的选择萃取性能,考察萃取过程中基底离子强度、pH值以及吸附与解吸时间等萃取条件对萃取性能的影响。结果表明;在最佳萃取条件下,MIP-SCSE对模板分子及其它酚类物质具有一定选择性能和较高的富集能力,对双酚A的线性范围为1.0～200μg/L;检出限LOD(S/N=3)为0.67μg/L;定量限LOQ(S/N=10)为2.24μg/L。在实际水样分析中,模板分子加标回收率为86.2%～112.2%。在MIP-SCSE使用过程中,萃取饼不与容器壁接触,因此具有优良的使用寿命,至少可连续使用600 h。     

Determination of bisphenol A in water by isotope dilution headspace solid-phase microextraction and gas chromatography/mass spectrometry without derivatization

The original solid-phase microextraction (SPME) fibers use an epoxy resin adhesive that releases bisphenol A (BPA) during thermal desorption of the fiber. This adversely affects the method detection limit and accuracy when these products are used for the determination of BPA. In this work, 5 new metal alloy SPME fibers that do not use epoxy resins were compared for the extraction of BPA in water. The performance of the optimum SPME fiber with 60 microm carbowax-polyethylene glycol coating for the headspace SPME of BPA in water was investigated systematically under different extraction conditions. Salt was found to increase the partitioning of BPA from water into the headspace until saturation was reached. Partitioning of BPA from water into the headspace also increased at higher extraction temperatures, as did longer extraction times. However, extraction of BPA from water onto the SPME fiber was not improved for solutions adjusted to pH 2 compared to the unadjusted neutral solutions. The new BPA method showed good linearity over the concentration range of 2.5 to 40 microg/L [correlation coefficient (r2) = 0.995] .The method detection limit for BPA was 0.5 microg/L, while the instrument detection limit was as low as 0.05 microg/L. Good repeatability was observed for BPA at levels of 5 and 20 microg/L with relative standard deviation values < 10%. The automated headspace SPME method developed in this work was used to investigate migration of BPA from polycarbonate bottles into water, and levels of BPA in water ranged from 1.7 to 4.1 microg/L.     

亚临界水萃取-高效液相色谱法测定聚碳酸酯水杯中双酚A和苯酚的迁移量

建立了亚临界水萃取-高效液相色谱同时测定聚碳酸酯(PC)水杯中双酚A和苯酚迁移量的方法。选择萃取温度120 ℃、萃取压力6.89 MPa(1000 psi)、静态萃取时间1 h、萃取1次对11种样品进行测定。双酚A的迁移量为6.81～11.16 μg/g。5种样品中未检出苯酚,其余样品中苯酚迁移量为3.25～6.08 μg/g。在优化的测定条件下,双酚A和苯酚在8 min内达到基线分离。双酚A和苯酚分别在0.05～20 mg/L和0.02～20 mg/L范围内线性关系良好,相关系数(r)均大于0.9997,检出限分别为7.6 μg/L和2.0 μg/L。日内及日间的重复性(以RSD计)分别小于5.21%及11.63%。传统的浸提法结果表明长时间浸提会使PC材料发生微弱水解。相比传统的浸提法,该方法的萃取效率提高了49～106倍。该方法简便、快速、环保,可用来测定PC水杯中双酚A和苯酚的迁移量。     

分散液-液微萃取/高效液相色谱法测定水样中的痕量双酚A

建立了分散液-液微萃取与高效液相色谱联用技术测定水样中痕量双酚A(BPA)的方法. 通过对实验条件的筛选及优化, 得到最佳条件: 22.5 μL氯苯作萃取剂、0.5 mL丙酮作分散剂、0 min静止萃取时间、调节pH 3.2左右、10%离子强度及9 mL水样体积. 此条件下方法的线性范围为0.5~100 μg/L(R2=0.9941), 检出限为0.10 μg/L. 在BPA质量浓度为1 μg/L条件下, 方法回收率为87.8%~111.0%, 相对标准偏差8.3%(n=5), 富集倍数范围1905~2527. 对添加不同BPA浓度的自来水、地表水及回用中水进行分析, 回收率分别为(108±11.1)%, (107±13.2)%及(81.2±6.2)%(n=3). 在既定的色谱条件下, BPA的测定不受乙炔基雌二醇、雌二醇、雌三醇、雌酮和壬基酚等雌激素的干扰.     

分子印迹聚合物为涂层的吸附萃取搅拌棒在环境水样双酚A含量测定中的应用

以双酚A(BPA)为单体,利用整体材料“原位”聚合技术制备以分子印迹聚合物为涂层的吸附萃取搅拌棒(MIP-SBSE),然后与高效液相色谱(HPLC)-二极管阵列检测器联用,探讨其对环境水样BPA的选择萃取性能。优化萃取过程中吸附和解吸时间、解吸液种类以及基底pH值和离子强度对目标化合物的选择吸附性能。在最佳条件下,MIP-SBSE可对模板分子进行有效的选择吸附,线性范围为1.0～200 μg/L,检出限(S/N=3)和定量限(S/N=10)分别为0.28μg/L和0.94 μg/L。在实际水样分析中,具有良好的加标回收率,其值为96.0%～108.7%。研究结果表明,所建立的方法具有简便、灵敏和环境友好等特点。     

Highly selective stir bar coated with dummy molecularly imprinted polymers for trace analysis of bisphenol A in milk

A water compatible molecularly imprinted polymers (MIPs) coated stir bar for bisphenol A(BPA) was prepared with 3,3',5,5'-tetrabromobisphenol A as the dummy template molecule in this study. The dummy molecularly imprinted polymers coated stir bar (DMIPs-SB) showed better selectivity than the bars coated with polydimethylsiloxane or non-imprinted polymers when used to extract BPA and its three analogues. The saturated adsorption amount of the DMIPs coating was 3.0 times over that of the non-imprinted polymers coating. To achieve the optimum extraction performance, several parameters, including extraction and desorption time, pH value, adsorption temperature and stirring speed were investigated. The high-performance liquid chromatography combined with the DMIPs-SB was employed in the analysis of BPA in aqueous solution. The linear range of BPA concentration in aqueous medium was 0.0228-2.28 ng/mL with correlation coefficient of 0.9994 and the detection limit was about 6.84 × 10(-3) ng/mL based on three times ratio of signal to noise. This method was directly applied to the determination of trace BPA in milk with satisfactory results.     

Quantification of the xenoestrogens 4-tert.-octylphenol and bisphenol A in water and in fish tissue based on microwave assisted extraction, solid-phase extraction and liquid chromatography-mass spectrometry

Extraction methods were developed for quantification of the xenoestrogens 4-tert.-octylphenol (tOP) and bisphenol A (BPA) in water and in liver and muscle tissue from the rainbow trout (Oncorhynchus mykiss). The extraction of tOP and BPA from tissue samples was carried out using microwave-assisted solvent extraction (MASE) followed by solid-phase extraction (SPE). Water samples were extracted using only SPE. For the quantification of tOP and BPA, liquid chromatography mass spectrometry (LC-MS) equipped with an atmospheric pressure chemical ionisation interface (APCI) was applied. The combined methods for tissue extraction allow the use of small sample amounts of liver or muscle (typically 1 g), low volumes of solvent (20 ml), and short extraction times (25 min). Limits of quantification of tOP in tissue samples were found to be approximately 10 ng/g in muscle and 50 ng/g in liver (both based on 1 g of fresh tissue). The corresponding values for BPA were approximately 50 ng/g in both muscle and liver tissue. In water, the limit of quantification for tOP and BPA was approximately 0.1 microg/l (based on 100 ml sample size).     

Selective Solid‐phase Extraction of Bisphenol A Using a Novel Stir Bar Based on Molecularly Imprinted Monolithic Material

In this paper, a novel monolithic stir bar based on molecularly imprinted polymer (MIP) was firstly developed by filling modified neodymium magnet (Nd₂Fe₁₄B) powders into a glass tube (60 × 4 mm), followed by the imprinted grafting with bisphenol A (BPA) as the template molecule by thermal polymerization. It has been successfully used for the stir bar sorptive extraction (SBSE) and its extraction performance illustrated that the MIP‐encapsulated stir bar had stronger affinity to the template molecule, compared with the stir bar based on the non‐imprinted molecularly polymer (NIP). Under the optimal extraction conditions, a simple method based on the coupling of MIP‐SBSE with high performance liquid chromatography (HPLC) was used for the selective determination of the model mixtures of BPA, 4‐phenylphenol (PP) and phenol (P) in bottled water. The recoveries of BPA, PP and P were in the range of 88.5‐96.1%, 78.2‐89.7%, 81.3‐89.5% at three spiked levels, respectively, demonstrating that higher extraction and the specific absorption occurred between the template molecule and the prepared MIP stir bar.     

分子印迹磁性固相萃取/液相色谱法检测奶制品中的双酚A

以双酚A(BPA)为模板分子,磁性二氧化硅(Fe_3O_4@SiO_2)为载体,4-乙烯基吡啶(4-VP)为功能单体,采用表面分子印迹技术制备了双酚A磁性分子印迹聚合物微球(Fe_3O_4@SiO_2-MIPs)。通过红外光谱、透射电镜等对Fe_3O_4@SiO_2-MIPs进行了结构和形貌的表征。将制得的Fe_3O_4@SiO_2-MIPs作为磁性吸附剂,分离富集奶制品中的BPA,建立了分子印迹磁性固相萃取/液相色谱法测定奶制品中BPA的新方法。结果表明,在优化条件下,Fe_3O_4@SiO_2-MIPs对BPA具有良好的选择性,最大吸附容量达13.50 mg/g,在0.05~5.0 mmol/L浓度范围内有良好的线性关系(r2=0.993 4),方法检出限为0.037μg/L,样品加标回收率为86.2%~93.1%,相对标准偏差为2.9%~3.8%。该方法高效快速,选择性好,可用于牛奶样品中痕量BPA的检测。