P3HT/CdS/TiO2/ZnO一维有序核壳式纳米棒阵列的构制及其在杂化太阳电池中的应用研究

采用恒电位法在铟锡氧化物导电玻璃(ITO)上制备了高度有序一维ZnO纳米棒阵列,将ZnO纳米棒阵列在TiO2溶胶中采用提拉法制备出了一维TiO2/ZnO核壳式纳米棒阵列.在一维TiO2/ZnO核壳式纳米棒阵列上电沉积CdS纳米晶得到一维CdS/TiO2/ZnO核壳式纳米棒阵列,然后在一维CdS/TiO2/ZnO核壳式纳米棒阵列上电沉积聚3-己基噻吩(P3HT)薄膜得到P3HT/CdS/TiO2/ZnO核壳式纳米结构薄膜.以该纳米结构薄膜电极为光阳极制备出新型纳米结构杂化太阳电池,研究了该类电池的光电转换性能,初步探讨了该类电池的工作机理.     

种子层对TiO2纳米棒阵列取向生长及界面态的影响

利用水热法制备了金红石相的单晶TiO2纳米棒阵列, 利用扫描电子显微镜(SEM)、Ｘ射线衍射仪(XRD)、紫外可见分光光度计(UV-Vis)以及表面光电压谱仪(SPS)研究了其形貌、结构以及光电性质. 通过不同生长基底对比实验发现F掺杂SnO2导电玻璃基底和种子层对纳米棒阵列的生长起决定作用, TiO2种子层与SnO2:F基底晶格匹配, 有利于晶体外延生长, 使TiO2纳米棒阵列的取向性更强. 根据场调制表面光电压测量结果, 金红石相的TiO2与基底界面处的能带向上弯曲, 在FTO/TiO2界面存在大量界面态, 这些界面态可能成为光生载流子的复合中心. 实验结果表明引入种子层不仅有利于TiO2纳米棒的取向生长, 而且极大地减少界面态, 有望提高电荷的收集效率.     

Rectangular bunched rutile TiO2 nanorod arrays grown on carbon fiber for dye-sensitized solar cells

Because of their special application in photovoltaics, the growth of one-dimensional single-crystalline TiO(2) nanostructures on a flexible substrate is receiving intensive attention. Here we present a study of rectangular bunched TiO(2) nanorod (NR) arrays grown on carbon fibers (CFs) from titanium by a "dissolve and grow" method. After a corrosion process in a strong acid solution, every single nanorod is etched into a number of small nanowires. Tube-shaped dye-sensitized solar cells are fabricated by using etched TiO(2) NRs-coated CFs as the photoanode. An absolute energy conversion efficiency of 1.28% has been demonstrated under 100 mW cm(-2) AM 1.5 illumination. This work demonstrates an innovative method for growing bunched TiO(2) NRs on flexible substrates that can be applied in flexible devices for energy harvesting and storage.     

Rutile TiO2 nano-branched arrays on FTO for dye-sensitized solar cells

Hierarchical TiO(2) nanostructures would be desirable for preparing dye-sensitized solar cells because of their large amount of dye adsorption and superior light harvesting efficiency, as well as efficient charge separation and transport properties. In this study, rutile TiO(2) nano-branched arrays grown directly on transparent conductive glass (FTO) were prepared by a facile two-step wet chemical synthesis process, using a simple aqueous chemical growth method involving immersing the TiO(2) nanorod arrays in an aqueous TiCl(4) solution as seeds, which were prepared by a hydrothermal method. The dye-sensitized solar cells based on the TiO(2) nano-branched arrays which were only about 3 μm in length show a short-circuit current intensity of 10.05 mA cm(-2) and a light-to-electricity conversion efficiency of 3.75%, which is nearly three times as high as that of bare nanorod arrays, due to the preferable nanostructure, which not only retains the efficient charge separation and transport properties of the nanorod arrays, but also can improve the amount of dye adsorption due to the increased specific surface area from the nanobranches.     

Correlating interface heterostructure, charge recombination, and device efficiency of poly(3-hexyl thiophene)/TiO2 nanorod solar cell

The charge recombination rate in poly(3-hexyl thiophene)/TiO(2) nanorod solar cells is demonstrated to correlate to the morphology of the bulk heterojunction (BHJ) and the interfacial properties between poly(3-hexyl thiophene) (P3HT) and TiO(2). The recombination resistance is obtained in P3HT/TiO(2) nanorod devices by impedance spectroscopy. Surface morphology and phase separation of the bulk heterojunction are characterized by atomic force microscopy (AFM). The surface charge of bulk heterojunction is investigated by Kelvin probe force microscopy (KPFM). Lower charge recombination rate and lifetime have been observed for the charge carriers in appropriate heterostructures of hybrid P3HT/TiO(2) nanorod processed via high boiling point solvent and made of high molecular weight P3HT. Additionally, through surface modification on TiO(2) nan,orod, decreased recombination rate and longer charge carrier lifetime are obtained owing to creation of a barrier between the donor phases (P3HT) and the acceptor phases (TiO(2)). The effect of the film morphology of hybrid and interfacial properties on charge carrier recombination finally leads to different outcome of photovoltaic I-V characteristics. The BHJ fabricated from dye-modified TiO(2) blended with P3HT exhibits 2.6 times increase in power conversion efficiency due to the decrease of recombination rate by almost 2 orders of magnitude as compared with the BHJ made with unmodified TiO(2). In addition, the interface heterostructure, charge lifetime, and device efficiency of P3HT/TiO(2) nanorod solar cells are correlated.     

TiO2/Au纳米棒阵列的制备及其光催化性能

采用电沉积和旋转涂膜相结合的方法成功制备了高度有序的TiO2/Au纳米棒阵列催化剂.扫描电镜和透射电镜结果表明,TiO2薄膜均匀地包覆在Au纳米棒的表面,形成核壳型的一维阵列结构.X射线衍射分析表明所获得TiO2为(101)晶面优先生长的锐钛矿晶相.紫外-可见漫反射光谱显示,由于Au和TiO2间肖特基结的存在造成吸收红...     

Preparation of dye-sensitized solar cells using template free TiO2 nanotube arrays for enhanced power conversion

Journal of Sol-Gel Science and Technology - By using the vertically aligned ZnO nanorod arrays (NRAs), TiO2 nanoparticles attached ZnO nanorods (TiO2@ZnO) and TiO2 nanotube arrays (NTAs) were...     

A novel photoanode architecture of dye-sensitized solar cells based on TiO2 hollow sphere/nanorod array double-layer film

A novel TiO(2) double-layer (DL) film consisting of TiO(2) hollow spheres (HSs) as overlayer and single-crystalline TiO(2) nanorod arrays (RAs) as underlayer was designed as the photoanode of dye-sensitized solar cells (DSSCs). This new-typed TiO(2) HS/RA DL film could significantly improve the efficiency of DSSCs owing to its synergic effects, i.e. the relatively large specific surface area of TiO(2) HSs for effective dye adsorption, enhanced light harvesting capability originated from TiO(2) RA film, and rapid interfacial electron transport in one-dimensional TiO(2) nanorod arrays. The overall energy-conversion efficiency of 4.57% was achieved by the formation of TiO(2) DL film, which is 16% higher than that formed by TiO(2) HS film and far larger than that formed by TiO(2) RA film (η=0.99%). The light absorption and interfacial electron transport, which play important roles in the efficiency of DSSCs, were investigated by UV-vis absorption spectra and electrochemical impedance spectra.     

A general approach for the growth of metal oxide nanorod arrays on graphene sheets and their applications

In the fabrication of flexible devices, highly ordered nanoscale texturing, such as semiconductor metal oxide nanorod arrays on flexible substrates, is critical for optimal performance. Use of transparent conducting films, metallic films, and polymer substrates is limited by mechanical brittleness, chemical and thermal instability, or low electrical conductivity, low melting point, and so on. A simple and general nanocrystal-seed-directed hydrothermal route has now been developed for large-scale growth of nanorod arrays of various semiconductor metal oxides (MO), including TiO(2), ZnO, MnO(2), CuO, and ZrO(2) on both sides of flexible graphene (G) sheets to form sandwichlike MO/G/MO heterostructures. The TiO(2)/G/TiO(2) heterostructures have much higher photocatalytic activity than TiO(2) nanorods, with a photocatalytic degradation rate of methylene blue that is four times faster than that of the TiO(2) nanorods, and are thus promising candidates for photocatalytic decontamination.     

Self-organized TiO2 nanorod arrays on glass substrate for self-cleaning antireflection coatings

Herein we report the direct fabrication of TiO(2) subwavelength structures with 1-dimensional TiO(2) nanorods on glass substrate through solvothermal process to form self-cleaning antireflection coatings. TiO(2) precursor solutions with different solvent constituents create TiO(2) nanorods with much different morphologies grown on glass substrates. Apiculate TiO(2) nanorods with vertical orientation are grown on the glass substrate which is solvothermally treated in the precursor solution containing ethylene glycol. This glass substrate exhibit the highest transmittance of 70-85% in the range of 520-800 nm and negligible absorption in visible light region (400-800 nm). Furthermore, the TiO(2) nanorod arrays show high hydrophobicity and photocatalytic degradation ability which offer the glass substrate self-cleaning properties for both hydrophilic and oily contaminants.     

Characteristics of diluted magnetic semiconductor based on Mn-doped TiO2 nanorod array films

Journal of Solid State Electrochemistry - In this work, un-doped and Mn-doped TiO2 nanorod (NR) array films were successfully prepared by hydrothermal method that deposited on FTO substrate at...     

Nanoparticle and nanorod TiO2 composite photoelectrodes with improved performance

A novel nanoparticle-nanorod composite TiO(2) photoelectrode is fabricated. A 3.20% efficiency is achieved by using a 2.1 μm-thick as-prepared photoelectrode, which is about 3 times of that obtained by a nanorod array electrode (1.05%). The results demonstrate that the composite nanostructure can take advantage of both fast electron transport (nanorod) and high surface area (nanoparticle).     

纳米结构ZnO在TiO_2薄膜上的电化学沉积及其表征

在三电极体系中,以硝酸锌水溶液作为电解液,采用阴极还原电沉积法成功实现了一维纳米结构ZnO阵列在TiO2纳米粒子/ITO导电玻璃薄膜基底上的沉积,并通过XRD、SEM、EDS和PL光谱等方法对样品进行了表征.重点研究了薄膜基底、电解液浓度、沉积时间、六次亚甲基四胺(HMT)的引入对ZnO沉积及其发光性质的影响.结果显示:与ITO玻璃基底相比,ZnO更易于在TiO2纳米粒子薄膜上实现电化学沉积.ZnO属于六方晶系的铅锌矿结构,并且沿着c-轴方向表现出明显的择优化生长,以形成垂直于基底的ZnO纳米棒阵列.延长沉积时间、增加电解液浓度和引入一定量的HMT等均对ZnO的生长有促进作用,进而使其纳米棒的结晶度和取向程度提高,进而解释了所得的薄膜分别约在375和520nm处表现出ZnO的强而窄的带边紫外光发射峰和弱而宽的表面态绿光发射带.     

N-TiO_2/ZnO复合纳米管阵列的掺杂机理及其光催化活性

以ZnO纳米柱阵列为模板,采用溶胶-凝胶法制备出TiO2/ZnO和N掺杂TiO2/ZnO的复合纳米管阵列.扫描电镜(SEM)、X射线光电子能谱(XPS)和紫外-可见漫反射吸收光谱(UV-Vis)的结果表明:两种阵列的纳米管均为六角形结构,直径约为100nm,壁厚约为20nm;在N-TiO2/ZnO复合纳米管阵列中,掺入的N离子主要是以N-Ox、N-C和N-N的形式化学吸附在纳米管表面,仅有少量的N离子以取代式掺杂的方式占据TiO2晶格O的位置;表面N物种形成的表面态能级和取代式掺杂导致带隙的窄化,增强了纳米管阵列的光吸收效率,促进了光生载流子的分离.光催化实验结果表明,N离子的掺杂有利于N-TiO2/ZnO复合纳米管阵列光催化活性的提高.     

电化学制备异质二氧化钛结构增强其在光电分解水中转化效率（英文）

本文描述了一种利用电化学方法合成第二型异质二氧化钛纳米棒结构的方法,这种纳米棒由部分还原的黑色二氧化钛和原始的白色二氧化钛组成.这种异质结结构的半还原的二氧化钛纳米棒与原始的白色二氧化钛和完全还原的黑色二氧化钛纳米棒相比,展现出更好的光电催化性能.这可归结于这种条件下合成的纳米棒具备的协同作用.一方面,这类结构增强了整个太阳光光谱的利用率.底层的黑色二氧化钛能够大量吸收可见光,而上层的白色二氧化钛能够较好的利用太阳光中紫外光的部分.另一方面,因为形成了第二型异质结结构,电荷的激发分离和传输得到了有效的控制.这种简单的制备方法可进一步拓展合成其他金属氧化物,来进一步研究光电分解水的性能.本文利用传统的三电极系统:0.05 mol/L的硫酸作为电解液,在加–0.5 V的偏压下进行.相比与已报道的还原手段,该电解液中质子的浓度相对比较低,可以保证这个还原过程逐步发生.电化学还原曲线可以明显反映二氧化钛还原的过程,尽管从扫描电子显微镜中很难观察到响应的区别,但是在该过程中,电极片的颜色发生了明显的变化.相应的,我们将这个系列的电极进行了光学和晶体学的研究,发现其在还原过程中,能带能够逐步减小.而在X射线衍测试当中,仅最终完全还原的得到的样品在20度左右出现两个额外的峰,可归结为还原状态的二氧化钛.电化学扫描进一步测试其能带的相应位置,证明了黑色被还原的二氧化钛和白色的原始二氧化钛是同时存在的.最后将这个系列光电极光电催化分解水的性能进行了比较,发现在同等的测试条件下,形成异质结结构的二氧化钛具有最高的光催化效率,其值大约是白色二氧化钛的三倍,同时也比纯黑的二氧化钛增长了20%左右.另外,异质结结构的二氧化钛与黑色的相比,在可见光区域有相同的效率的同时具备更好的紫外光转化效率.最后,我们分析了异质结形成以后的相对应的能带结构,该结构能够更好的促进光吸收和转化.     

Dye-sensitized solar cells based on a single-crystalline TiO2 nanorod film

Highly crystalline TiO2 nanorods with lengths of 100-300 nm and diameters of 20-30 nm have been synthesized by a hydrothermal process in a cetyltrimethylammonium bromide surfactant solution. The microstructure measured by X-ray diffraction and high-resolution transmission electron microscopy was a pure highly crystalline anatase phase with a long nanorod shape. The addition of a triblock copolymer poly(ethylene oxide)100-poly(propylene oxide) 65-poly(ethylene oxide)100 (F127) decreased the length of the nanorods and kept the rod shape of the particles even after sintering at high temperatures. The rod shape kept under high calcination temperatures contributed to the achievement of the high conversion efficiency of light-to-electricity as discussed in the paper. A high conversion efficiency of light-to-electricity of 7.29% was obtained with the TiO2 single-crystalline anatase nanorod cell.     

Substrate-free, large-scale, free-standing and two-side oriented single crystal TiO2 nanorod array films with photocatalytic properties

A substrate-free, large-scale, free-standing and two-side oriented single crystal rutile TiO(2) nanorod array film with a thickness of over ten micrometers, self-assembled via a facile hydrothermal reaction of titanium powder in a mixture solution of H(2)O(2) and HCl, exhibits high activity for the photocatalytic degradation of methyl orange.     

Synthesis of hybrid CdS-Au colloidal nanostructures

We explore the growth mechanism of gold nanocrystals onto preformed cadmium sulfide nanorods to form hybrid metal nanocrystal/semiconductor nanorod colloids. By manipulating the growth conditions, it is possible to obtain nanostructures exhibiting Au nanocrystal growth at only one nanorod tip, at both tips, or at multiple locations along the nanorod surface. Under anaerobic conditions, Au growth occurs only at one tip of the nanorods, producing asymmetric structures. In contrast, the presence of oxygen and trace amounts of water during the reaction promotes etching of the nanorod surface, providing additional sites for metal deposition. Three growth stages are observed when Au growth is performed under air: (1) Au nanocrystal formation at both nanorod tips, (2) growth onto defect sites on the nanorod surface, and finally (3) a ripening process in which one nanocrystal tip grows at the expense of the other particles present on the nanorod. Analysis of the hybrid nanostructures by high-resolution TEM shows that there is no preferred orientation between the Au nanocrystal and the CdS nanorod, indicating that growth is nonepitaxial. The optical signatures of the nanocrystals and the nanorods (i.e., the surface plasmon and first exciton transition peaks, respectively) are spectrally distinct, allowing the different stages of the growth process to be easily monitored. The initial CdS nanorods exhibit band gap and trap state emission, both of which are quenched during Au growth.     

Kinetics of electron recombination of dye-sensitized solar cells based on TiO2 nanorod arrays sensitized with different dyes

The performance and electron recombination kinetics of dye-sensitized solar cells based on TiO(2) films consisting of one-dimensional nanorod arrays (NR-DSSCs) which are sensitized with dyes N719, C218 and D205, respectively, have been studied. It has been found that the best efficiency is obtained with the dye C218 based NR-DSSCs, benefiting from a 40% higher short-circuit photocurrent density. However, the open circuit photovoltage of the N719 based cell is 40 mV higher than that of the organic dye C218 and D205 based devices. Investigation of the electron recombination kinetics of the NR-DSSCs has revealed that the effective electron lifetime, τ(n), of the different dye based NR-DSSCs shows the sequence of C218 > D205 > N719. The higher V(oc) with the N719 based NR-DSSC is originated from the more negative energy level of the conduction band of the TiO(2) film. In addition, in comparison to the DSSCs with the conventional nanocrystalline particles based TiO(2) films, the NR-DSSCs have shown over two orders of magnitude higher τ(n) when employing N719 as the sensitizer. Nevertheless, the τ(n) of the DSSCs with the C218 based nanorod arrays is only ten-fold higher than that of the nanoparticles based devices. The remarkable characteristic of the dye C218 in suppressing the electron recombination of DSSCs is discussed.     

Oxide thin films based on ordered arrays of 1D nanostructure. A possible approach toward bridging material gap in catalysis

TiO(2) thin films based on ordered arrays of 1D nanostructures (nanorods, nanotubes) are proposed as suitable model materials in studies for bridging material and complexity gap in catalysis. The samples were prepared by anodic oxidation of Ti foils. By changing the preparation conditions (pH, procedure of application of the potential), different types of 1D nanostructure and different characteristics of the ordered array of these 1D nanostructures could be obtained. This allows studying the effect of nanodimension and 3D nanoarchitecture on the characteristics and reactivity of these catalysts. It is also shown that TiO(2) thin films characterized by a well-ordered array of titania nanorod behave as photonic materials, thus showing unique properties of light harvesting efficiency.