Underpotential deposition of Cu on partially oxidized Rh electrodes

The underpotential deposition (UPD) of copper on partially oxidized rhodium electrodes was studied in acid medium using potentiodynamic techniques. The process was analyzed as a function of the potential and time of deposition. The potentiodynamic I-E patterns for the oxidative dissolution of Cu provide evidence for the existence of a chemical reaction between Cu and oxygen existing on the electrode surface. Redistribution of the active sites is also possible when appreciable quantities of oxidized species are simultaneously reduced by the UPD process. The partially oxidized rhodium electrodes were prepared by cyclic voltammetry and anodic polarization. The later method provided the most oxidized surfaces, but, even in this case, the degree of oxygen surface coverage was lower than that corresponding to a monolayer. Received: 11 July 1997 / Accepted: 10 February 1998     

Underpotential deposition studies of copper on glassy carbon

Studies on the deposition and dissolution of copper from 0·5 M sulphuric acid solutions onto glassy carbon (GC) using potential sweep techniques indicated that an additional peak occurs at higher positive potentials than the bulk stripping peak. This peak is identified as due to the stripping of underpotential deposited (UPD) copper. Results of investigations on the effect of sweep rate, deposition potential and time of deposition on the peak characteristics of UPD and bulk deposited copper are also reported.     

Glucose biosensor based on graphite electrodes modified with glucose oxidase and colloidal gold nanoparticles

The electrochemistry of glucose oxidase (GOx) immobilized on a graphite rod electrode modified by gold nanoparticles (Au-NPs) was studied. Two types of amperometric glucose sensors based on GOx immobilized and Au-NPs modified working electrode (Au-NPs/GOx/graphite and GOx/Au-NPs/graphite) were designed and tested in the presence and the absence of N-methylphenazonium methyl sulphate in different buffers. Results were compared to those obtained with similar electrodes not containing Au-NPs (GOx/graphite). This study shows that the application of Au-NPs increases the rate of mediated electron transfer. Major analytical characteristics of the amperometric biosensor based on GOx and 13 nm diameter Au-NPs were determined. The analytical signal was linearly related to glucose concentration in the range from 0.1 to 10 mmol L^?1. The detection limit for glucose was found within 0.1 mmol L^?1 and 0.08 mmol L^?1 and the relative standard deviation in the range of 0.1–100 mol L^?1 was 0.04–0.39%. The τ_1/2 of V _max characterizes the storage stability of sensors: this parameter for the developed GOx/graphite electrode was 49.3 days and for GOx/Au-NPs/graphite electrode was 19.5 days. The sensor might be suitable for determination of glucose in beverages and/or in food.     

Underpotential deposition of copper on electrochemically treated polycrystalline Au surfaces

Cyclic voltammetric responses of electrochemically treated polycrystalline gold surfaces have been examined using Cu-UPD probe reactions (UPD-underpotential deposition). The treatment procedure used appears to induce preferential crystal orientation of the Au surface with a very small roughness factor and affords a simple method to obtain well-defined surfaces for electrochemical studies.     

Stripping voltammetry of copper and lead using gold electrodes modified with self-assembled monolayers

One problem associated with using bare solid metal electrodes, such as gold and platinum, in stripping analysis to determine heavy metal ions such as lead and copper ions in dilute solutions is that underpotential deposition (UPD) gives multiple stripping peaks in the analysis of mixtures. These peaks are often overlapped and cannot be conveniently used for analytical purposes. Bifunctional alkylthiols, such as 3-mercaptopropionic acid, with an ionizable group on the other terminal end of the thiol can form self-assembled monolayers (SAMs) on the surface of the gold electrode. It is shown that such an SAM-modified gold electrode minimizes the UPD effects for the stripping analysis of lead and copper. The anodic peak potential shifts and the peak shape changes, indicating that the SAM changes the deposition and stripping steps of these heavy metal ions. Thus, the sensitivity levels for both single species and mixtures can be significantly improved for the conventional solid electrodes. The mechanism of the deposition reaction at the SAM-modified gold electrodes is discussed. Received: 29 May 1997 / Accepted: 24 June 1997     

Underpotential deposition of thallium, lead, and cadmium at silver electrodes modified with self-assembled monolayers of (3-mercaptopropyl)trimethoxysilane

Investigation of the underpotential deposition (UPD) of three metals-Tl, Pb, and Cd-on Ag surfaces modified with self-assembled monolayers (SAMs) of (3-mercaptopropyl)trimethoxysilane (3MPT) is reported. On the basis of the observation of negative potential shifts for their UPD processes, Tl and Pb undergo UPD directly on the underlying Ag surface by insertion between the Ag-S bond. This process is proposed to occur by penetration of the 3MPT monolayer by hydrated metal ions through spaces in six-membered siloxane rings that form at the terminus of the 3MPT layer after hydrolysis and condensation. In contrast, Cd does not undergo similarly facile UPD at 3MPT-modified Ag electrodes due to a hydrated ion size too large to fit through these openings. The voltammetric evidence that suggests that the hydrated metal cation size, as described by the Stokes diameter, is the primary determinant of Ag electrode accessibility for UPD through the cross-linked 3MPT layer is further supported by molecular mechanics energy minimization computations of six-membered siloxane rings on each of the three low-index faces of Ag. Finally, the 3MPT monolayer is shown to be exceptionally stable to repeated UPD/stripping cycles of Tl and Pb in contrast to SAMs of similar thickness formed from normal alkanethiols.     

ToF-secondary ion mass-spectrometric study of copper deposition and stripping on directly heated screen-printed gold electrodes

We report about a new kind of directly heated gold electrode. All electrodes including a directly heated gold loop electrode, a Ag pseudo reference, and a carbon counter electrode have been screen-printed on a ceramic alumina substrate. Thermal behaviour was studied by potentiometry using either an external or the integrated reference electrode. Stripping voltammetric copper signals were greatly improved at elevated deposition temperature. Secondary ion mass spectrometric studies (ToF-SIMS) revealed that different negative ionic species of copper complexes can be found on the gold electrode surface as a result of ion bombardment during SIMS analysis like Cu^?, CuCl^? and CuCl₂ ^?. SIMS surface imaging using a fine focussed ion beam over the surface allowed us to obtain ion images (chemical maps) of the analyzed sample. SIMS depth profile analysis of the gold loop electrode was performed after copper deposition at room temperature (23 °C) and at 60 °C. CuCl₂ ^? ion was used for the depth profile studies as it has shown the highest intensity among other observed species. Surface spectroscopic analysis, surface imaging and depth profile analysis have shown that the amount of deposited copper species on the gold loop electrode was increased upon increasing electrode temperature during the deposition step. Therefore, the presence of chloride in the solution will hinder underpotential deposition of Cu(0) and lead to badly defined and resolved stripping peaks.     

Layer-by-layer immobilization of horseradish peroxidase on a gold electrode modified with colloidal gold nanoparticles

An amperometric biosensor, based on layer-by-layer self-assembly of colloidal gold nanoparticles, cysteine and horseradish peroxidase on Nafion modified electrode surface by electrostatic adsorption, has been used for the determination of hydrogen peroxide. The electrochemical behavior of the multilayer film was studied by cyclic voltammetry, linear sweep voltammetry and chronoamperometry. The step layer-by-layer adsorption interface morphology was further characterized by means of electrochemical impedance spectroscopy and cyclic voltammetry. The performance and factors influencing the resulted biosensor were studied in detail. The sensor displayed an excellent electrocatalytic response to the reduction of H₂O₂ without the aid of an electron transfer mediator. Linear response to H₂O₂ was obtained for the concentration range from 1.6 μM to 2.4 mM under optimized conditions. The detection limit of the biosensor was 0.5 μM (S/N = 3), and the sensor achieved 95% of the steady-state current within 10 s. The sensor exhibited high sensitivity, selectivity and stability. Correspondence: Yan Liu, College of Chemistry, Chongqing Normal University, Chongqing 400047, P.R. China     

Highly enantioselective discrimination of amino acids using copper deposition on a gold electrode modified with homocysteine monolayer

An extremely enhanced enantioselectivity was achieved for the detection of enantiomers of alanine (Ala), leucine (Leu), and 3,4-dihydroxyphenylalanine (DOPA) based on the voltammograms for the deposition of Cu from Cu complexes of the amino acids at an Au electrode modified with a self-assembled monolayer (SAM) of l-homocysteine (Hcy). The enantioselective current density peak for the Cu deposition was found to change with increasing number of potential cycles after the addition of Cu(II), and the highest enantioselectivity was observed immediately after the addition of Cu(II). Besides, enantioselectivity was not observed with proline, whose five-membered ring contains the nitrogen atom of a secondary amino group, while some amino acids with a primary amine group such as Ala, Leu, and DOPA exhibited enantioselectivity. These results suggest that the chiral ligand exchange reaction at the l-Hcy SAM-modified Au electrode, namely, the enantioselective formation of diastereomeric complexes of Cu(II) with target enantiomers and l-Hcy self-assembled on the Au electrode, plays an important role in the chiral discrimination based on the Cu deposition.     

Electrochemical evaluation of lectin-sugar interaction on gold electrode modified with colloidal gold and polyvinyl butyral

In this work, ConA and CramoLL lectins were immobilized on gold nanoparticles (AuNp) with polyvinyl butyral (PVB), and adsorbed on the surface of gold (Au) electrodes. Electrochemical impedance spectroscopy (EIS), in the frequency range from 100mHz to 100KHz, and cyclic voltammetry (CV), from -0.2 to 0.7V, were performed on these electrodes, in phosphate buffer (PBS) solution containing 10mM K(3)[Fe(CN)(6)]/K(4)[Fe(CN)(6)] (1:1) mixture as a redox probe. EIS and CV measurements showed that redox probe reactions on the modified Au electrodes were partially blocked due to the adsorption of AuNp-ConA-PVB and AuNp-CramoLL-PVB. SEM images showed the presence of aggregates of AuNp-ConA on PVB spherules in a tridimensional structure on the surface of the Au electrode. Bovine serum albumin (BSA) was adsorbed on the AuNp-Lectin-PVB modified electrode in order to block the remaining free gold sites. Both EIS and CV techniques yielded results that confirm positive responses of the lectins to ovalbumin agglutination. These results indicate an improvement of the sensitivity for detection of sugars that can be applicable to construction of a biosensor sensitive to glycoproteins in solution.     

Underpotential deposition and involved alloy formation of cadmium on silver particles modified HOPG substrates

Cadmium underpotential deposition (UPD) on Ag particles modified highly ordered pyrolytic graphite (HOPG) surfaces, and the involved alloy formation were studied by conventional electrochemical techniques. Voltammetric results indicated that the Cd UPD followed an adsorption behavior different from that observed for massive Ag electrodes and Ag particles supported on vitreous carbon. Nanometer-sized bimetallic Cd–Ag particles were characterized by ex situ atomic force microscopy (AFM). Initially, AFM images show Ag deposits of similar size distributed preferably on HOPG step edges. No remarkable morphological changes are observed on the surface after the subsequent Cd deposition, suggesting that the Cd particles are deposited selectively over the Ag crystals. From the analysis of desorption spectra, employing different polarization times, and density functional theory (DFT) calculations, the formation of a Cd–Ag surface alloy could be inferred.     

Electron transfer of hemoglobin at electrodes modified with colloidal clay nanoparticles

Nanostructured sodium montmorillonite was prepared via a colloidal chemical approach and deposited onto glassy carbon electrodes (GCE). Subsequently, hemoglobin was spontaneously adsorbed onto the clay membrane-modified electrode. The colloidal clay nanoparticles and the adsorbed protein were characterized by scanning electron microscopy (SEM) and atomic force microscopy (AFM). The electrochemical impedance behavior of the system was studied using a microlithographically fabricated interdigitated microsensor electrode (IME). The interaction of the clay nanoparticles with hemoglobin was investigated by UV-VIS spectroscopy and electrochemical methods. The heme protein adsorbed in this way displayed a well-defined electrode process and the electron transfer was confirmed to originate from its heme site. Furthermore, nitric oxide affects the hemoglobin electrochemistry.     

Anguler-resolved raman spectroscopy of pyridine on copper and gold electrodes

The surface enhanced Raman scattering from pyridine molecules adsorbed on smooth copper or gold electrodes exhibits a similar strong enhancement as for pyridine on Ag. The intensity is very sensitive to the angle of incidence, and the signal is detectable only in a narrow angular range, when only monolayer amounts of the metals have been dissolved and redeposited electrochemically.     

Analytical applications of gold electrodes modified with monolayers of thiolated cyclodextrins

The sequential method for the preparation of cyclodextrin monolayers is used to prepare modified electrodes responsive towards selected guest molecules: ferrocene, ibuprofen, methylene blue, dopamine and menadione. The inclusion into cyclodextrin cavities is monitored using cyclic voltammetry and the mediating role of the immobilized molecules towards solution species is shown on the example of dopamine oxidation.     

Immobilization of peroxidase glycoprotein on gold electrodes modified with mixed epoxy-boronic Acid monolayers

The development of bioelectronic enzyme applications requires the immobilization of active proteins onto solid or colloidal substrates such as gold. Coverage of the gold surface with alkanethiol self-assembled monolayers (SAMs) reduces nonspecific adsorption of proteins and also allows the incorporation onto the surface of ligands with affinity for complementary binding sites on native proteins. We present in this work a strategy for the covalent immobilization of glycosylated proteins previously adsorbed through weak, reversible interactions, on tailored SAMs. Boronic acids, which form cyclic esters with saccharides, are incorporated into SAMs to weakly adsorb the glycoprotein onto the electrode surface through their carbohydrate moiety. To prevent protein release from the electrode surface, we combine the affinity motif of boronates with the reactivity of epoxy groups to covalently link the protein to heterofunctional boronate-epoxy SAMs. The principle underlying our strategy is the increased immobilization rate achieved by the weak interaction-induced proximity effect between slow reacting oxyrane groups in the SAM and nucleophilic residues from adsorbed proteins, which allows the formation of very stable covalent bonds. This approach is exemplified by the use of phenylboronates-oxyrane mixed monolayers as a reactive support and redox-enzyme horseradish peroxidase as glycoprotein for the preparation of peroxidase electrodes. Quartz crystal microbalance, atomic force microscopy, and electrochemical measurements are used to characterize these enzymatic electrodes. These epoxy-boronate functional monolayers are versatile, stable interfaces, ready to incorporate glycoproteins by incubation under mild conditions.     

Sub-ppt detection limits for copper ions with Gly-Gly-His modified electrodes

An electrochemical metal ion sensor has been developed with a detection limit of less than 0.2 ppt by the covalent attachment of the tripeptide Gly-Gly-His as a recognition element to a 3-mercaptopropionic acid modified gold electrode.     

Electrochemical characterizations of nickel deposition on aromatic dithiol monolayers on gold electrodes

The electronic properties of pristine and cross-linked (CL) self-assembled monolayers (SAMs) of [1,1';4',1' '-terphenyl]-4,4' '-dimethanethiol (TPDMT) on Au were studied by electrochemical measurements, including cyclic voltammetry and impedance spectroscopy. In addition, nickel deposition onto the TPDMT and CL-TPDMT substrates was investigated. In all cases, the TPDMT and CL-TPDMT films were found to be insulators, which effectively blocked the ionic permeation of electrolyte, preventing direct access of ions to the Au electrode. At the same time, CL-TPDMT is a better electric insulator than the pristine TPDMT SAM. The top Ni layer in the Ni/CL-TPDMT/Au arrangement was electrically isolated from the Au substrate, and no short circuits occurred. This layer was found to be conductive and relatively stable in the broad potential range in the electrolyte solution.     

Underpotential deposition of cobalt onto polycrystalline platinum

An electrochemical study of cobalt electrodeposition onto a polycrystalline platinum electrode from an aqueous solution (10⁻² M CoCl₂ + 1 M NH₄Cl (pH 9.5)) was carried out through cyclic voltammetry and potential step techniques. Analysis of the voltammetric data clearly showed that a cobalt adlayer is formed during the application of potential in the underpotential deposition (upd) region. Formation of this cobalt adlayer involved the simultaneous presence of both adsorption and 2D nucleation processes. Cobalt adlayers obtained by linear voltammetry in upd region were analyzed employing diffuse reflectance spectroscopy (DRS). By using theoretical quantum studies at PM6//HF/LANL1MB level, it was possible to assign the peaks obtained by DRS at 328 and 337 nm to the cobalt adsorption on Pt(111) and Pt(100), respectively, while the signals recorded at 355 and 362 nm were related with the clean platinum surfaces Pt(100) and Pt(111). Also, quantum calculations at the PM6 level indicated that the energy formation order is Co-Pt(100) > Co-Pt(111) > Co-Pt(110) > Co-Co(surface).