超电容器用电极材料氮化钼的改性研究(I)——钒酸氨添加物对电极性能的影响

应用XRD、SEM和循环伏安等方法对γ_氮化钼及其复合电极进行了表征和测量 ,研究了浸渍液中钒酸铵浓度对成膜物质的表面形貌、结晶形态和电容的影响 .结果表明 :添加钒酸铵导致成膜物质中生成四方晶系的VOMoO4 ,这对氮化钼电极的电容特性有重要影响 .其影响机理为VOMoO4 改变了成膜物质的结晶形态和结构 ,导致氮化钼的部分非晶化 ,循环伏安测试显示了氮化钼电极具有良好的电容特性 .掺钒之后 ,电极的工作电势范围拓宽 ,比电容加大 ;浸渍液中钒钼最佳摩尔比为 35∶6 5 .     

Behavior of thin films of poly(oxyethylene)-poly(oxybutylene) copolymers studied by brewster angle microscopy and atomic force microscopy

Surface films of two copolymers of ethylene oxide (E) and butylene oxide (B), namely E23B8 and E87B18, have been examined by Brewster angle microscopy (BAM) and atomic force microscopy (AFM). Isotherms taken on unsupported films of these copolymers at the air-water interface showed a clear gas to liquid phase transition for E57B18 and a barely discernible phase transition for E23B8. The BAM studies showed a gradual brightening of the films as the surface pressure was increased, which was associated with a film thickening and/or a film densification. Several bright spots were also observed within the films, with the number of spots increasing gradually as the film surface pressure was increased. AFM studies of these films did not show any localized ordering, which fits in with the results from our previous X-ray study of these copolymers [Hodges, C. S.; Neville, F.; Konovalov, O.; Gidalevitz, D.; Hamley, I. W.; Langmuir 2006, 22 (21), 8821-8825], where no long-range ordering was observed. AFM imaging showed two sizes of particulates that were irregularly spaced across the film. The larger particulates were associated with silica contaminants from the copolymer synthesis, whereas the smaller particulates were assumed to be aggregated copolymer. An analysis of the semidilute region of the isotherm showed that while both copolymers had intermixed ethylene oxide and butylene oxide units, the lower molecular weight E23B8 copolymer manifested significantly more intermixing than E87B18.     

The in situ characterization and structuring of electrografted polyphenylene films on silicon surfaces. An AFM and XPS study

An atomic force microscope was used so as to structure by nanofriction films of polynitrophenylene electrografted on substrates of n-type silicon (100) with the native oxide on the top of the surface. AFM measurements of thin films thickness have been carried out in the electrolytic solution for different applied potentials during the electrografting. This investigation allows (i) to determine the relationship between the applied potential and the final thickness of electrografted polyphenylene films and (ii) to specify how the thin layers grow. XPS analysis confirmed the AFM observations on (i) the effective shaving of the grafted polymer chains under mechanical stress and (ii) the existence of a potential threshold for electrografting a polyphenylene film on silicon oxide surfaces. The presence of a residual film in the rubbed zone was attributed to stronger interactions between the first electrografted layer and the native oxide of silicon (through Si-C or/and Si-O-C bonds) than those insuring the cohesion of the multilayer (C-C and C-N bonds).     

非化学计量的混合价态氧化钼(VI,V)修饰微电极的电化学制备

在新鲜配制的Na2MoO4的弱酸性水溶液中, 通过循环电位扫描在碳纤维微电极表面可沉积一层均匀的蓝色氧化钼(VI, V)薄膜, 膜的厚度通过电量进行控制。在电沉积之前, 电极的阳极化处理不仅可以加快氧化钼的电沉积, 而且可以改善膜的伏安行为。溶液的pH值对膜的电沉积和伏安行为有极大的影响。膜的阴极过程被认为是产生青钼铜: HxMoO3 (0相似文献   

Surface structure and photoluminescence properties of AZO thin films on polymer substrates

Al‐doped zinc oxide (AZO) thin films were deposited on indium tin oxide (ITO) coated polyethylene terephthalate (PET) substrates by radio frequency (RF) magnetron sputtering method at room temperature. The effects of film thickness on the surface structure and the photoluminescence properties of the films were investigated by atomic force microscopy (AFM), secondary ion mass spectroscopy (SIMS) and room temperature photoluminescence (PL). AFM analysis showed that the surface of all films was extremely flat and uniform at nanoscale. Root mean square (RMS) value of the surface roughness which scanned the surface area of 3 µm by 3 µm and grain size increased with increasing the film thickness. Thus, the surface morphology of the films became rough because of the coarse grains. The depth profile of AZO layers was analyzed by SIMS. It was found that the thickness of the AZO layer is almost same with the desired film thickness. The PL intensity of the dominant peak decreased and shifted slightly towards the shorter wavelengths with increasing the film thickness. According to the relationships between luminescence intensity and crystalline characteristics, it was observed that the intensity of the peak decreased by the increased surface area of the grains. Copyright © 2014 John Wiley & Sons, Ltd.     

The influence of fluoride on the physicochemical properties of anodic oxide films formed on titanium surfaces

The influence of fluoride (and its concentration) on the electrochemical and semiconducting properties of anodic oxide films formed on titanium surfaces was investigated by performing electrochemical measurements (potentiodynamic/pontiostatic polarization, open circuit potential (OCP), and capacitance measurements) for a titanium/oxide film/solution interface system in fluoride-containing 1.0 M HClO(4) solution. On the basis of the Mott-Schottky analysis, and with taking into account both the surface reactions (or, say, the specifically chemical adsorption) of fluoride ions at the oxide film surface and the migration/intercalation of fluoride ions into the oxide film, the changes in the electrochemical behavior of titanium measured in this work (e.g., the blocked anodic oxygen evolution, the increased anodic steady-state current density, the positively shifted flat band potential, and the positively shifted film breakdown potential) were interpreted by the changes in the surface and the bulk physicochemical properties (e.g., the surface charges, surface state density, doping concentration, and the interfacial potential drops) of the anodic films grown on titanium. The fluoride concentrations tested in this work can be divided into three groups according to their effect on the electrochemical behavior of the oxide films: < or =0.001 M, 0.001-0.01 M, and >0.01 M. By tracing the changes of the OCP of the passivated titanium in fluoride-containing solutions, the deleterious/depassive effect of fluoride ions on the titanium oxide films was examined and evaluated with the parameter of the film breakdown time. It was also shown that the films anodically formed on titanium at higher potentials (>2.5 V) exhibited significantly higher stability against the fluoride attack than that either formed at lower potentials (<2.5 V) or formed natively in the air.     

Stability of the gold/silica thin film interface: electrochemical and surface plasmon resonance studies

This article reports chemical stability studies of a gold film electrode coated with thin silicon oxide (SiOx) layers using electrochemical, surface plasmon resonance (SPR) and atomic force microscopy (AFM) techniques. Silica films with different thicknesses (d = 6.4, 9.7, 14.5, and 18.5 nm) were deposited using a plasma-enhanced chemical vapor deposition technique (PECVD). For SiOx films with d >/= 18.5 nm, the electrochemical behavior is characteristic of a highly efficient barrier for a redox probe. SiOx films with thicknesses between 9.5 and 14.5 nm were found to be less efficient barriers for electron transfer. The Au/SiOx interface with 6.4 nm of SiOx, however, showed an enhanced steady-state current compared to that of the other films. The stability of this interface in solutions of different pH was investigated. Whereas a strongly basic solution led to a continuous dissolution of the SiOx interface, acidic treatment produced a more reticulated SiOx film and improved electrochemical behavior. The electrochemical results were corroborated by SPR measurements in real time and AFM studies.     

Layered molybdenum oxide thin films electrodeposited from sodium citrate electrolyte solution

Molybdenum oxide thin films were prepared electrochemically onto the selenium predeposited tin oxide-coated glass substrates using 0.22 M sodium citrate (C₆H₅Na₃O₇) solution (pH 8.3) and sodium molybdate as a precursor. Cyclic voltammetry was used to determine the deposition potential effects on molybdenum compound speciation, while quantitative thin film composition was obtained from X-ray photoelectron spectroscopy depth profiles. Thin molybdenum film growth and composition was potential dependant. Predominant molybdenum species was Mo(IV) at all deposition potentials and deposition times. Optical properties of the molybdenum oxide thin films were determined using UV–VIS spectroscopy. The absorption edge varied between 560 and 650 nm, whereas optical band gap values—between 1.79 and 2.19 eV—well within the limits for solar light-induced chemical reactions.     

Swift heavy ion induced effects at Mo/Si interface and silicide formation

Swift heavy ion (SHI) induced modification at metal/Si interfaces has emerged as an interesting field of research due to its large applications. In this study, we investigate SHI‐induced mixed molybdenum silicide film with ion fluences. The molybdenum thin films were deposited on silicon substrates using e‐beam evaporation at 10^?8 torr vacuum. Thin films were irradiated with Au ions of energy 120 MeV to form molybdenum silicide. The samples were characterized by grazing incidence X‐ray diffraction (GIXRD) technique for the identification of phase formation at the interface. Rutherford backscattering spectrometry (RBS) was used to investigate the elemental distribution in the films. The mixing rate calculations were made and the diffusivity values obtained lead to a transient melt phase formation at the interface according to thermal spike model. Irradiation‐induced effects at surface have been observed and roughness variations at the surface were calculated using atomic force microscopy (AFM) technique. Copyright © 2009 John Wiley & Sons, Ltd.     

Self‐Assembly and Surface Photovoltage Response of ZnS Nanoparticulate Films Sensitized by Tetrasulfonated Copper Phthalocyanine

Composite films of ZnS nanoparticle‐polyelectrolyte were fabricated by the layer‐by‐layer self‐assembly technique. The optical properties and structure of the films were characterized by UV‐vis absorption spectra and AFM. The films sensitized by tetrasulfonated copper phthalocyanine (CuTsPc) show wide photovoltaic response range. The surface photovoltages corresponding to the ZnS nanoparticle interband transition and CuTsPc Q band transition in the sensitized film are approximately three to four times stronger than those in the ZnS nanoparticle‐polyelectrolyte film and CuTsPc film, respectively, which is attributed to the electron transition from the excited state of CuTsPc to the conduction band of ZnS nanoparticles.     

Model films of cellulose ID – improved preparation method and characterization of the cellulose film

An optimization study of the preparation of spin-coated cellulose model films from the NMMO/DMSO system on silicon wafers has been made. The study shows that the cellulose concentration ID the solution determines the cellulose film thickness and that the temperature of the solution affects the surface roughness. A lower solution temperature results ID a lower surface roughness at cellulose concentrations below 0.8%. Using the described method, ID ID possible to prepare films with thicknesses of 30–90 nm with a constant surface roughness by changing the cellulose concentration, i.e. by dilution with DMSO. On these films, water has a contact angle less than 20° and about 50% of the material can, according to CP/MAS ¹³C-NMR spectroscopy on corresponding fibrous material, be considered to consist of crystalline cellulose ID type material. ID has further been shown that AFM can be used to determine the thickness of cellulose films, ID both dry and wet states. ID this method, the difference ID height between the top surface and the underlying wafer has been measured at an incision made into the cellulose film. The cellulose films have also been spin-coated with the same technique as on the silicon oxide wafer onto the crystal ID a quartz crystal microbalance (QCM). These model films were found to be suitable for swelling measurements with the QCM. The films were very stable during this type of measurement and films with different amounts of charges gave different swelling responses depending on their charges. As expected, films with a higher charge showed a higher swelling.     

Deformation controlled assembly of binary microgel thin films

We describe the assembly of two-component, hydrogel microparticle (microgel) monolayer films onto solid substrates via passive Coulombic adsorption from solution. By using two different microgel types with nearly identical sizes but different degrees of softness, the influence of particle deformation on film composition was determined. Determination of the microgel properties using a variety of light scattering techniques allowed for predictions of the film composition as a function of solution composition using a random sequential adsorption (RSA) model. The films were then studied via atomic force microscopy (AFM), and surface coverage and population statistics were determined from the images and compared to the model predictions. Deviations from the predicted particle adsorption behavior can be directly traced to differences in particle softness, deformation, and particle footprint following adsorption, which biases the particle coverage to the more rigid (smaller footprint) particles. Furthermore, by using a mixture of degradable and nondegradable core/shell particles, the identity of the particles can be unambiguously determined by measuring AFM height changes following erosion of the core from the microgels. These results show that, regardless of the solution diffusion properties of soft particles, their competition for surface adsorption from a binary mixture is largely dictated by their interactions with the surface and their deformation at the surface.     

石墨烯/银复合薄膜的制备及表征

采用静电自组装技术,通过交替沉积聚(二烯丙基二甲基氯化铵)(PDDA)(或硝酸银)和氧化石墨烯,制备氧化石墨烯/PDDA薄膜和氧化石墨烯/硝酸银复合薄膜。然后在600℃下通入氩气和氢气进行气氛还原得到石墨烯薄膜和石墨烯/银复合薄膜。采用AFM、SEM、XPS、UV-Vis以及四探针电阻仪等对薄膜结构及性质进行表征。结果表明,通过静电自组装法可以获得生长均匀的薄膜。对比于相同自组装次数的石墨烯薄膜,石墨烯/银复合薄膜具有更好的透光性和更低的薄膜方块电阻。在λ=500 nm时,四层石墨烯/银复合薄膜的透过率为85%左右,而石墨烯薄膜的透过率为72%左右;石墨烯薄膜的方阻为161.39 kΩ.□-1,而石墨烯/银复合薄膜的方阻为99.11 kΩ.□-1。     

射频等离子沉积聚硅氧烷薄膜的XPS研究

用CVD方法在一台射频放电等离子体聚合实验装置内成功地制备了沉积聚酯薄膜基底有机聚硅氧烷薄膜.该薄膜在有原子氧模拟实验装置内具有抗原子氧剥蚀的良好性能,对航天器等材料表面起到防护作用.有机聚硅氧烷薄膜与等离子体沉积时氧的泄露量有关,且沉积密度经AFM检测有较大的差异.并用XPS较详细考察了不同工艺制备的聚硅氧烷官能团构成和表面状态,以期得到优良的防剥蚀膜.     

TiO2纳米膜表面结构形态特征

采用反胶束法制备TiO2纳米溶胶,用浸渍提拉法在不同的条件下制备了三种TiO2多孔纳米薄膜,并利用AFM、SEM、XRD等方法对膜表面结构物理化学特性进行表征.结果表明三种膜基本上由粒径约为59 nm的纳米粒子以不同的方式堆积而成,溶胶刚生成时浸提一次,干燥、焙烧得到膜上纳米粒子分布均匀,所生成的二次粒子粒径最小,二次粒子形成的二次表面粗糙度最小,浸提10次得到膜上纳米粒子间存在较丰富缝隙结构,二次粒子粒径及其形成的表面粗糙度较大,而溶胶制备好陈化6 h后浸提得到的膜上二次粒子粒径最大,表面粗糙度最高.由分形理论估算得到三种膜的分形维数分别是2.22、2.20和2.27. XRD测试表明,膜上TiO2为锐钛矿晶相.这些结果表明,采用不同制备步骤得到的膜,其表面结构形态存在较大的差异.     

铂/{还原氧化石墨烯/硅钨酸盐}_n复合物的制备及其电催化性能

利用层层自组装(LBL)结合原位光照还原法,制备了一系列{还原氧化石墨烯/多金属氧酸盐}n多层复合膜({rGO/POMs}_n),并以此作为载体,再通过恒电势法将Pt纳米粒子电沉积到复合膜载体上,得到一种P t/{rGO/SiW_(12)}_n燃料电池阳极纳米复合膜催化剂。用紫外可见分光光度计(UV-Vis)、原子力显微镜(AFM)以及扫描电子显微镜(SEM)等技术手段对载体复合多层膜的生长情况以及负载Pt纳米簇的表面形貌进行表征。结果表明,载体多层膜{rGO/SiW_(12)}_6被连续均匀地组装到了不同基底(氧化铟锡,ITO或玻碳,GC)表面且多层膜表面平整,在选定恒电势下,沉积于其表面的Pt纳米粒子具有花簇状形貌且分布均匀。比较研究了分别引入3种不同的多金属氧酸盐(硅钨酸盐SiW_(12),磷钼酸盐PMo_(12),磷钨酸盐PW_(12))制得的多层复合膜催化剂,即Pt/{rGO/SiW_(12)}_6、Pt/{rGO/PMo_(12)}_6和Pt/{rGO/PW_(12)}_6。电化学实验研究表明,在甲醇酸性溶液中,Pt/{rGO/SiW_(12)}_6复合膜相较于Pt/{rGO/PMo_(12)}_6、Pt/{rGO/PW_(12)}_6和Pt作为催化剂对甲醇氧化具有更好的电催化活性、电化学稳定性以及更优异的抗CO毒化性能,是一种颇有应用前景的燃料电池阳极催化剂。     

Photochromism and electrochemistry of a dithienylcyclopentene electroactive polymer

A bifunctional substituted dithienylcyclopentene photochromic switch bearing electropolymerisable methoxystyryl units, which enable immobilization of the photochromic unit on conducting substrates, is reported. The spectroscopic, electrochemical, and photochemical properties of a monomer in solution are compared with those of the polymer formed through oxidative electropolymerization. The electroactive polymer films prepared on gold, platinum, glassy carbon, and indium titanium oxide (ITO) electrodes were characterized by cyclic voltammetry, X-ray photoelectron spectroscopy (XPS), and atomic force microscopy (AFM). The thickness of the films formed is found to be limited to several monolayer equivalents. The photochromic properties and stability of the polymer films have been investigated by UV/vis spectroscopy, electrochemistry, and XPS. Although the films are electrochemically and photochemically stable, their mechanical stability with respect to adhesion to the electrode was found to be sensitive to both the solvent and the electrode material employed, with more apolar solvents, glassy carbon, and ITO electrodes providing good adhesion of the polymer film. The polymer film is formed consistently as a thin film and can be switched both optically and electrochemically between the open and closed state of the photochromic dithienylethene moiety.     

Nano silver coated patterned silica thin film by sol–gel based soft lithography technique

We report the fabrication of nano silver coated patterned silica thin film by sol–gel based soft lithography technique. Initially, silica gel film on soda lime silica glass was prepared by dipping technique from a silica sol of moderate silica concentration. A PolydimethylSiloxane elastomeric stamp containing the negative replica of the patterns of commercially available compact disc was used for embossing the film and the embossed film was cured up to 450 °C in pure oxygen atmosphere for oxide film. Finally, a precursor solution of AgNO₃ in water containing polyvinyl alcohol as an organic binder was made and used for coating on the patterned silica film by dipping technique and cured the sample up to 450 °C in reducing gas atmosphere to obtain nano silver layer. The formation of only cubic silver (~4.0 nm) and both cubic silver (~5.2 nm) and silver oxide (~3.6 nm) crystallites at 350 and 450 °C film curing temperatures respectively were confirmed by XRD measurements. The % of nano silver metal and silver oxide were 75.4 and 24.6 respectively. The nano-structured surface feature was visualized by FESEM whereas AFM revealed the high fidelity grating structure of the films. Presence of both spherical and rectangular structure (aspect ratio, 2.37) of nano silver/silver oxide was confirmed by TEM. The films were also characterized by UV–Vis spectral study. The patterned film may find application in chemical sensor devices.     

Modification of indium-tin oxide electrodes with thiophene copolymer thin films: optimizing electron transfer to solution probe molecules

We describe the modification of indium-tin oxide (ITO) electrodes via the chemisorption and electropolymerization of 6-{2,3-dihydrothieno[3,4-b]-1.4-dioxyn-2-yl methoxy}hexanoic acid (EDOTCA) and the electrochemical co-polymerization of 3,4-ethylenedioxythiophene (EDOT) and EDOTCA to form ultrathin films that optimize electron-transfer rates to solution probe molecules. ITO electrodes were first activated using brief exposure to strong haloacids, to remove the top approximately 8 nm of the electrode surface, followed by immediate immersion into a 50:50 EDOT/EDOTCA co-monomer solution. Potential step electrodeposition for brief deposition times was used to grow copolymer films of thickness 10-100 nm. The composition of these copolymer films was characterized by solution depletion studies of the monomers and atomic force microscopy (AFM), X-ray photoelectron spectroscopy, and Fourier transform infrared spectroscopy (reflection-absorption infrared spectroscopy (RAIRS)) of the product films. The spectroscopic data suggest that the composition of the copolymer approaches 80% EDOTCA when electropolymerization occurs from concentrated (10 mM) solutions. AFM characterization shows that electrodeposited poly(EDOT)/poly(EDOTCA) (PEDOT/PEDOTCA) films are quite smooth, with texturing on the nanometer scale. RAIRS studies indicate that these films consist of a combination of EDOTCA units with noninteracting -COOH groups and adjacent hydrogen-bonded -COOH groups. The EDOTCA-containing polymer chains appear to grow as columnar clusters from specific regions, oriented nearly vertically to the substrate plane. As they grow, these columnar clusters overlap to form a nearly continuous redox active polymer film. ITO activation and formation of these copolymer films enhances the electroactive fraction of the electrode surface relative to a nonactivated, unmodified "blocked" ITO electrode. Outer-sphere solution redox probes (dimethylferrocene) give standard rate coefficients, kS > or = 0.4 cm.s-1, at 10 nm thick copolymer films of PEDOT/PEDOTCA, which is 3 orders of magnitude greater than that on the unmodified ITO surface and approaches the values for kS seen on clean gold surfaces.     

Structural and optical properties of TiO2 thin films prepared by spin coating

Transparent semiconducting thin films of titanium oxide (TiO₂) were deposited on glass substrates by the sol–gel method and spin-coating technique. The physical properties of the prepared films were studied as a function of the number of spun-cast layers. The microstructure and surface morphology of the TiO₂ films were characterized by X-ray diffraction (XRD) and atomic force microscopy (AFM), with respect to the film thickness. The XRD analysis reveals that the films are polycrystalline with an anatase crystal structure and a preferred grain orientation in the (101) direction. The morphological properties were investigated by AFM, which shows a porous morphology structure for the films. The optical properties of the films were characterized by UV–Visible spectrophotometry, which shows that the films are highly transparent in the visible region and their transparency is slightly influenced by the film thickness, with an average value above 80 %. The dependence of the refractive index (n), extinction coefficient (k), and absorption coefficient (α) of the films on the wavelength was investigated. A shift in the optical band gap energy of the films from 3.75 to 3.54 eV, as a function of the film thickness, has been observed.