A study of the electrocatalytic oxidation of methanol on a nickel–salophen-modified glassy carbon electrode

Nickel–salophen-modified glassy carbon electrodes prepared by transferring one drop of Ni–salophen complex solution on the electrode surface. This modified electrode has been used for the electrocatalytic oxidation of methanol in alkaline solutions with various methods such as cyclic voltammetry, chronoamperometry, and electrochemical impedance spectroscopy. The electrooxidation was observed as large anodic peaks, and early stages of the cathodic direction of potential sweep around 20 mV vs. Ag|AgCl|KCl_sat. A mechanism based on the electrochemical generation of Ni (Ш) active sites and their subsequent consumptions by methanol have been discussed. EIS studies were employed to unveil the charge transfer rate as well as the electrical characteristics of the catalytic surface. For the electrochemical oxidation of methanol at 5.0 M concentration, charge transfer resistance of nearly 0.936 kΩ was obtained, while the resistance of the electrocatalyst layer was about 111.6 Ω.     

Application of phosphotungstic acid–nickel composite-modified carbon paste electrode for electrocatalytic oxidation of methanol in alkaline solution

Phosphotungstic acid (PWA) was used for accumulation of nickel ions at the carbon paste electrode for preparation of PWA-modified CPE (PWA/CPE). The PWA was evenly mixed with graphite powder and paraffin oil. Then, for preparation of Ni/PWA/CPE, Ni ions were included onto the PWA/CPE surface through immersion method at open circuit condition. The scanning electron microscopy (SEM), energy-dispersive spectroscopy and electrochemical methods were used to verify the prepared electrodes. The SEM images reveal that morphology of the CPE was influenced by PWA addition. Application of the Ni/PWA/CPE for methanol oxidation was explored by various electrochemical techniques. Electrochemical response of methanol oxidation at the surface of Ni/PWA/CPE was 2.5 times higher than that Ni/CPE. The obtained results indicated that the modified electrode exhibited high electrocatalytic activity toward methanol oxidation. Then, catalytic rate constant was found to be 8.25 × 10⁴ cm³ mol ^?1 s^?1 using chronoamperometry method. Furthermore, the effects of several parameters, such as PWA loading, NiSO₄ concentration, accumulation time and methanol concentration toward methanol oxidation at the surface of this modified electrode as well as stability, have been investigated.     

Influence of the nickel content on the electrocatalytic activity of thin nanostructured Co–Te–Ni–O films

The influence of nickel addition in Co–Te–O catalytic films, obtained by vacuum co-evaporation of Co, Ni, and TeO₂ on electrocatalytic activity toward oxygen reactions in alkaline media has been investigated. Bifunctional gas-diffusion oxygen electrodes were prepared by direct deposition of catalyst films on gas-diffusion membranes consisting of hydrophobized carbon blacks. The method used allows the deposition of nanostructured films consisting of intertwined nanowires with high surface area. Thus, obtained electrodes with different atomic ratio R _(Co+Ni)/Te of the catalyst, fresh and thermally treated at 100 °C temperatures were electrochemically tested by means of cyclic voltammetry and steady-state voltammetry. It has been shown that the partial replacement of Co with about 30 at.% Ni leads to the increase in the film catalytic activity toward oxygen evolution reaction.     

The study of the speciation of uranyl–sulphate complexes by UV–Vis absorption spectra decomposition

Uranyl–sulphate complexes are the predominant U(VI) species present in acid solutions resulting either from underground uranium ore leaching or from the remediation of leaching sites. Thus, the study of U(VI) speciation in these solutions is of practical significance. The spectra of UO₂(NO₃)₂ + Na₂SO₄ solutions of different Φ _S = [SO₄²⁻]/[U(VI)] ratio at pH = 2 were recorded for this purpose. As the presence of uranyl-nitrate complexes should be expected under these experimental conditions, the spectra of UO₂(NO₃)₂ + NaNO₃ solutions with different Φ _N = [NO₃⁻]/[U(VI)] ratio at pH = 2 were also measured. The effects of Φ _S and Φ _N ratios value were most pronounced in wavelength interval 380–500 nm. Therefore, these parts of experimental overall spectra were used for deconvolution into the spectra of individual species by the method proposed. It enabled to calculate stability constants of anticipated species at zero ionic strength. The Specific Ion Interaction Theory (SIT) was used for this purpose. Stability constants of UO₂SO₄, UO₂(SO₄)₂²⁻, UO₂NO₃ ⁺ and UO₂(NO₃)₂ coincided well with published data, but those for UO₂(SO₄)₃⁴⁻ and UO₂(NO₃)₃⁻ were significantly lower.     

Electrodeposited nanostructured Pt–Ru co-catalyst on graphene for the electrocatalytic oxidation of formaldehyde

The electrochemical oxidation of formaldehyde over graphene surfaces modified with Pt–Ru co-catalyst is presented. Graphene was chemically converted from graphite and Pt–Ru co-catalyst was electrochemically deposited using cyclic voltammetry. The hybrid surface is prepared using “green approaches” and displayed electrocatalytic activity towards formaldehyde in the form of current oscillations. The current oscillations that were mainly due to adsorption/desorption of carbonaceous oxidative products are a factor of several parameters such as the concentrations of both formaldehyde and supporting electrolyte in solution, the amount of catalyst loading, scan rate of potential, upper potential limit, and the temperature change. CCG/Pt–Ru exhibited higher electrocatalytic activity toward formaldehyde electro-oxidation, and intense electrochemical current oscillations were obtained at relatively low HCHO concentrations compared to other work mentioned in literature for CCG/Pt–Pd.     

Raman spectroscopic study of the structural change of uranium–thorium-mixed oxides before and after oxidation

Journal of Radioanalytical and Nuclear Chemistry - UO2 pellets doped with 1, 5 and 10 mol% Th before and after oxidation were analyzed by using Raman spectroscopy to investigate the Th...     

In situ surface Raman study of the induced codeposition mechanism of Ni–Mo alloys

The induced codeposition of molybdenum with nickel on a Ni–Cu alloy electrode has been investigated by means of in situ surface Raman spectroscopy to obtain information about the codeposition mechanism during electrodeposition of Ni–Mo alloys. The experimental results show that, in the NiSO₄-free solution, molybdate can only be reduced to a mixture of polyvalent molybdenum oxides and/or hydroxide, while, in the case where NiSO₄ coexisted in the solution, molybdate is first reduced to Mo(IV) oxide, which, as an intermediate, subsequently is reduced to molybdenum in alloy under the catalysis of inducing nickel.     

A survey on the effect of ionic liquid on electrochemical behavior and electrocatalytic activity of a phosphomolybdic acid-ionic liquid-MWCNT–modified glassy carbon electrode

Journal of Solid State Electrochemistry - The surface of a glassy carbon electrode modified with multi-walled carbon nanotubes (GCE/MWCNTs) was coated with a layer of phosphomolybdic acid (PMo12)...     

In situ Raman microscopy during discharge of a high capacity silicon–carbon composite Li-ion battery negative electrode

In situ Raman microscopy study has been performed in order to characterize the surface of the Si/C composite anode and also to monitor the alloying/dealloying behavior of Si/C with Li ion during electrochemical discharging/charging processes at a microscopic level. This study shows that the Si particles are covered by graphite and hard carbon, with demonstration of further evidence of amorphisation of silicon and presence of mixed phases of Li–Si.     

In situ infrared study of formate reactivity on water–gas shift and methanol synthesis catalysts

In order to investigate the methanol synthesis reaction from CO₂/H₂, a comparative study of the reactivity of formate species on different types of catalysts and catalyst supports has been carried out. Formic acid was adsorbed on water–gas shift catalysts, Cu/ZnO/Al₂O₃ methanol synthesis catalyst and ZnO/Al₂O₃ support, Cu/ZnO/ZrO₂ and Cu/ZnO/CeO₂ methanol synthesis catalysts as well as their corresponding supports ZnO/ZrO₂ and ZnO/CeO₂. Superior reactivity and selectivity of dedicated methanol synthesis catalysts was evidenced by their behavior during the subsequent heating ramp, when these samples showed the simultaneous presence of formates and methoxy species and a higher stability of these reaction intermediates in the usual temperature range for the methanol synthesis reaction.     

Synthesis of palladium–polypyrrole nanocomposite and its electrocatalytic properties in the oxidation of formaldehyde

Three alternative methods were developed for the synthesis of modifying palladium–polypyrrole layers on the surface of an inert electrode. Their electrocatalytic activity toward formaldehyde under inert atmosphere was checked. All the suggested methods are one-stage and allow synthesis of a film on the electrode surface from a solution containing a palladium salt and pyrrole in the absence of other active reagents. The electrochemical methods (potentiodynamic and double cathodic and anodic pulses techniques) in an aqueous medium give films with poorly reproducible electrocatalytic properties, while the chemical redox synthesis affords films with reproducibly high electroactivity toward methylene glycolate.     

Experimental study of a closed system in the sodium chlorite–iodine–ethyl acetoacetate oscillation reaction by UV–Vis and online FTIR spectrophotometric method

The sodium chlorite–iodine–ethyl acetoacetate (EAA) chemical oscillatory reaction system was studied by UV–Vis and online FTIR spectrophotometric method. The oscillation phenomenon does not occur as long as the reactants are mixed. There is a pre-oscillatory or induction period. The amplitude is small at the beginning stage and then increases with reaction time. Finally, the oscillation ceases suddenly. The amplitude and the number of oscillations are associated with the initial concentration of sodium chlorite, iodine, EAA and sulfuric acid. The equations for the triiodide ion reaction rate changing with reaction time and the initial concentrations on the oscillation stage were obtained. The intermediates were detected by the online FTIR analysis. Based upon the experimental data in this work and in the literature, a plausible reaction mechanism was proposed for the oscillation reaction.     

Statistical analysis of the impact of spectral correlation on observed formation constants from UV–visible spectroscopic measurements

Information retrieved from UV–visible spectroscopic data by application of a self-modelling factor analysis algorithm showed apparently systematically shifted thermodynamic properties for the same chemical system as a function of spectral slit widths. This empirical observation triggered a systematic investigation into the likely effects of residual and spectral correlation on the numerical results from quantitative spectroscopic investigations. If slit width was a nuisance factor it would reduce the comparability of information evaluated from spectroscopic data. The influence of spectral slit width was investigated by simulation, i.e. by generating and evaluating synthetic spectra with known properties. The simulations showed that increasing spectral correlation may introduce bias into factor analysis evaluations. By evaluation of the complete measurement uncertainty budget using threshold bootstrap target factor (TB CAT) analysis, the apparent shifts are insignificant relative to the total width of the quantitys measurement uncertainty. Increasing the slit widths causes some systematic effects, for example broadening of the registered spectral bands and reduction of spectral noise, because of higher light intensity passing to the detector. Hence, the observed systematic shifts in mean values might be caused by some latent correlation. As a general conclusion, slit width does not affect bias. However, the simulations show that spectral correlation and residual correlation may cause bias. Residual correlation can be taken into account by computer-intensive statistical methods, for example moving block or threshold bootstrap analysis. Spectral correlation is a property of the chemical system under study and cannot be manipulated. As a major result, evidence is given showing that stronger spectral correlation (r<–0.7) causes non-negligible bias in the evaluated thermodynamic information from such a system.     

In situ optical spectroscopic understanding of electrochemical passivation mechanism on sol–gel processed WO3 photoanodes

A prevailing understanding on electrochemical activation of photoelectrodes is that electrochemical treatment leads to increased charge carrier densities thereby improved photoelectrode performances.Contrary to this understanding, in this study enhanced photoactivity of WO₃ photoanode upon electrochemical treatment is ascribed to an extraordinary mechanism of surface trap passivation. The associated mechanism is analyzed by in situ optical spectroscopy, using which the optical propert...     

Electroless preparation and electrochemical behavior of a platinum-doped nickel hexacyanoferrate film–zinc modified electrode: catalytic ability of the electrode for electrooxidation of methanol

The use of a zinc substrate as an electrode and the modification of its surface by means of a thin film of platinum-doped nickel hexacyanoferrate (Pt-NiHCF) were developed. The modification conditions of the zinc surface including the electroless deposition of metallic nickel on the electrode surface from NiCl₂ solution, chemical derivatization of the deposited nickel to the NiHCF film in 0.5 M K₃[Fe(CN)₆] solution, and electrochemical penetration of metallic platinum into the modified film are described. The modified zinc electrodes prepared under optimum conditions show a well-defined redox couple due to the [Ni^IIFe^III/II(CN)₆]^1–/2– system. The effects of pH, the alkali metal cation, and the anion of the supporting electrolyte on the electrochemical characteristics of the modified electrode were studied in detail. The diffusion coefficients of hydrated alkali metal cations in the film (D), the transfer coefficient (), and the transfer rate constant for the electron (k_s) were calculated in the presence of some alkali metal cations. The electrocatalytic activity of the modified electrode for methanol oxidation was demonstrated. The stability of the modified electrode under various experimental conditions was investigated.     

Interaction of flavonoids,the naturally occurring antioxidants with different media: A UV–visible spectroscopic study

Quantitative parameters for interaction of flavonoids—the naturally occurring antioxidants, with solvents and surfactants are determined using UV–visible absorption spectroscopy. The availability of flavonoids; kaempferol, apigenin, kaempferide and rhamnetin in micelles of sodium dodecyl sulfate (SDS) is reflected in terms of partition coefficient, K_c. Thermodynamic calculations show that the process of transfer of flavonoid molecules to anionic micelles of SDS is energy efficient. A distortion in flavonoid's morphology occurs in case of kaempferol and apigenin in surfactant and water, exhibited in terms of a new band in the UV region of electronic spectra of these flavonoids. The partition coefficients of structurally related flavonoids are correlated with their antioxidant activities.     

In situ evaluation of chromium–DNA damage using a DNA-electrochemical biosensor

The in situ evaluation of the direct interaction of chromium species with double-stranded DNA (dsDNA) was studied using differential pulse voltammetry at a glassy carbon electrode. The DNA damage was electrochemically detected following the changes in the oxidation peaks of guanosine and adenosine bases. The results obtained revealed the interaction with dsDNA of the Cr(IV) and Cr(V) reactive intermediates of Cr(III) oxidation by O₂ dissolved in the solution bound to dsDNA. This interaction leads to different modifications and causes oxidative damage in the B-DNA structure. Using polyhomonucleotides of guanine and adenine, it was shown that the interaction between reactive intermediates Cr(IV) and Cr(V)–DNA causes oxidative damage and preferentially takes place at guanine-rich segments, leading to the formation of 8-oxoguanine, the oxidation product of guanine residues and a biomarker of DNA oxidative damage. The interaction of Cr(VI) with dsDNA causes breaking of hydrogen bonds, conformational changes, and unfolding of the double helix, which enables easier access of other oxidative agents to interact with DNA, and the occurrence of oxidative damage to DNA.     

Characterisation of Ni carbonate-bearing minerals by UV–Vis–NIR spectroscopy

Four nickel carbonate-bearing minerals from Australia have been investigated to study the effect of Ni for Mg substitution. The spectra of nullaginite, zaratite, widgiemoolthalite and takovite show three main features in the range of 26,720–25,855 cm⁻¹ (ν₁-band), 15,230–14,740 cm⁻¹ (ν₂-band) and 9,200–9,145 cm⁻¹ (ν₃-band) which are characteristic of divalent nickel in six-fold coordination. The Crystal Field Stabilization Energy (CFSE) of Ni²⁺ in the four carbonates is calculated from the observed ³A_2g(³F) → ³T_2g(³F) transition. CFSE is dependent on mineralogy, crystallinity and chemical composition (Al/Mg-content). The splitting of the ν₁- and ν₃-bands and non-Gaussian shape of ν₃-band in the minerals are the effects of Ni-site distortion from regular octahedral. The effect of structural cation substitutions (Mg²⁺, Ni²⁺, Fe²⁺ and trivalent cations, Al³⁺, Fe³⁺) in the carbonate minerals is noticed on band shifts. Thus, electronic bands in the UV–Vis–NIR spectra and the overtones and combination bands of OH and carbonate ion in NIR show shifts to higher wavenumbers, particularly for widgiemoolthalite and takovite.