纤维增强橡胶复合材料界面力学性能有限元分析

基于剪滞理论,引入双线性内聚力模型研究了纤维与基体界面应力传递机理.采用ABAQUS模拟了非理想界面在单纤维拔出过程中的脱粘失效,分析了不同脱粘阶段界面剪应力分布情况,以及界面刚度和纤维长径比对界面应力传递和拔出载荷的影响规律.结果 表明,在纤维受载失效过程中,纤维的拔出过程可分为4个阶段,即界面的完全粘结、损伤演化、...     

基于弹性-塑性内聚力模型的纤维拔出界面宏观行为分析

用解析法分析了单纤维从聚合物基体中的拔出过程,采用弹性—塑性内聚力模型模拟裂纹的扩展和界面失效,确定了临界纤维埋入长度,该值区分两种不同长度的纤维拔出过程. 在纤维拔出过程,界面经历不同的阶段. 纤维埋长小于临界长度时,界面的脱粘载荷与纤维的埋长成正比;超过临界长度后,界面的脱粘载荷近似为常数. 分析了界面参数对脱粘载荷的影响:增加界面的剪切强度和界面的断裂韧性,或减小界面裂纹萌生位移,均能提高界面的脱粘载荷;界面脱粘后无界面摩擦应力时,拔出载荷—位移曲线的峰值载荷等于界面的脱粘载荷;界面摩擦应力存在时,使峰值载荷大于脱粘载荷,需要较长的纤维埋入长度和较大的界面摩擦应力.      

共晶基陶瓷复合材料的断裂韧性

应用细观力学方法研究了由具有随机尺寸和方位的棒体共晶体构成的共晶基陶瓷复合材料的断裂韧性.首先根据棒状共晶体的细观结构特性,考虑共晶体边界处的微观滑移确定共晶陶瓷复合材料的开裂应力,当外载荷达到开裂应力时,裂纹开始扩展.然后分析裂纹表面处的棒状共晶体桥联力使裂纹产生闭合效应,减小裂纹尖端的应力集中,建立棒状共晶体桥联增韧机制;再依据棒状共晶体拔出过程中摩擦力做功,建立棒状共晶体拔出增韧机制.最后在棒状共晶体的桥联与拔出增韧机制的基础上,得到了共晶基陶瓷复合材料断裂韧性的理论表达式.结果表明共晶基陶瓷复合材料的断裂韧性与棒状共晶体的长径比密切相关.     

剪切增稠液改性软织物的单纱拉出测试研究

剪切增稠液浸渍柔性织物是防弹织物进行表面改性的潜在方法,利用剪切增稠液剪切率与粘度的极端非线性关系可显著提高纱线拔出力与拔出能量,从而增加柔性织物的抗冲击性能。本文以SiO_2为分散相、乙二醇为分散剂配置剪切增稠液,来浸渍Kevlar49平纹织物进行表面改性。对坯布与浸渍布进行纱线拔出测试,其载荷-位移曲线呈现相似趋势,均分为静摩擦与动摩擦两个阶段;与坯布的极限拔出载荷出现在静摩擦阶段不同,浸渍布的极限拔出载荷出现在动摩擦阶段,且明显大于坯布。另外,浸渍布的纱线拔出能量和面内剪切变形均有明显的提升,且与剪切增稠液的质量分数和纱线拉拔速率相关。     

一种新的界面脱粘和纤维拔出模型

对纤维增强复合材料中界面的脱粘和纤维的拔出行为进行了研究,通过纤维间距d来考虑纤维之间的相互影响,改变脱粘段的剪切强度和粘结段的临界能量释放率,推导出了纤维拉拔荷载和纤维脱粘长度之间的变化关系,与StangH的模型进行了对比,当纤维间距较大时,纤维之间的相互影响相对较小,此时与StangH的单根纤维拉拔情况较为相符,但当纤维间距较小时,由于临近纤维的影响,使得在相同脱粘长度的情况下,纤维拉拔荷载和纤维拔出端位移有减小的趋势,改变复合材料板层的厚度,由于影响了基体的变形,界面的脱粘和纤维的拔出行为也受到了相应的影响。     

基于Cosserat近场动力学的纤维混凝土破坏模拟

本文基于Cosserat近场动力学发展了一种纤维混凝土的近场动力学模型,对纤维混凝土的破坏现象进行研究。该模型考察了物质点独立的转动自由度和物质点间的力偶作用,而且有表征微结构尺寸的内禀长度,相比于传统的近场动力学模型,更适合描述纤维混凝土这类胶结颗粒材料的力学行为。本文采用完全离散的方式对纤维进行建模,引入了纤维拔出实验中拔出位移和切应力的关系,并且采用组构张量描述纤维的局部分布。数值算例部分模拟了单纤维拔出实验、带预制裂纹的平板拉伸实验和三点弯曲梁实验。数值结果和已有的数值模型以及实验进行了对比,验证了所提出模型的正确性。此外,本文还调查了微结构对纤维混凝土破坏的影响,数值结果显示Cosserat剪切模量和内禀长度会影响裂纹的局部分布,但是不会改变裂纹的主方向。     

钢筋与混凝土粘结试验及有限元模拟

建立了一种按接触条件模拟钢筋与混凝土之间相互作用的模型。通过试验确定钢筋与混凝土的一些基本力学参数:粘结刚度、摩擦系数、抗剪强度、径向挤压力和软化系数;进而通过有限元模拟分析了试件的拔出过程:弹性阶段、局部开裂阶段、内部拥塞阶段以及完全脱粘阶段。计算结果与试验结果符合较好,验证了本文计算模型的合理性,解决了传统连续体理论所无法解释的现象。     

植物根土界面摩擦力的影响因素研究

为探索影响林木根系与土壤界面摩擦力的因素,采用施加拔出荷载的方式对林木根系进行单根拔出试验.结果表明:根系与土壤界面的摩擦力随根系直径和埋深的增加而呈线性规律增大;平均摩擦力的大小随土壤含水率的增加呈现先增大后减小的规律;摩擦力随加载速率的增加而减小;不同树种的根系与土壤摩擦力和摩擦系数差异显著,平均摩擦力大小表现为白桦落叶松蒙古栎油松,平均摩擦系数表现为落叶松蒙古栎白桦油松.     

纤维／基体界面裂纹扩展断裂能

本文通过研究纤维／基体界面裂纹断裂能，分析了几种界面脱粘断裂功的理论表达式；着重研究了单纤维拔出试验中界面残余压应力及界面摩擦对界面裂纹能量释放率的重要性．     

基于界面端奇异性理论的单纤维拔出试验的试件设计

在单纤维拔出试验中，由于试件的界面端存在应力奇异性，这使试验所得到的界面剪切强度数据失去合理性[1]。但从文献[1]关于微珠脱粘试验研究的结论中可以发现当基体的楔形角小于某临界角度后，微珠试件界面端应力奇异性几乎消失。由此启发我们设计出一种楔形角小于该纤维／基体系统临界角的锥面的拔出试件，这样即可以防止出现传统拔出试件在界面端的强应力奇异性，又可以避免微珠脱粘试验自身的缺陷。界面端具有任意楔形角的轴对称模型被用于分析和确定纤维／基体系统的临界角，对方程进行渐近展开和分离变量处理，根据边界条件可以得到关于特征值λ的特征方程，针对确定的纤维／基体系统可以得到特征值和楔形角的关系曲线，我们把应力奇异性指数等于-0．005时所对应的楔形角定义为临界角，以及根据临界角设计锥面拔出试件的方法。     

Application and analysis of functionally graded piezoelectrical rotating cylinder as mechanical sensor subjected to pressure and thermal loads

The exact thermoelastic analysis of a functionally graded piezoelectrical (FGP) rotating cylinder is investigated analytically. The cylinder is subjected to a combination of electrical, thermal, and mechanical loads simultaneously. The structure is a simplified model of a rotational sensor or actuator. The basic governing differential equation of the system is obtained by using the energy method. A novel term, named as the additional energy, is introduced to exact the evaluation of the energy functional. The solution to the governing differential equation is presented for two types of boundary conditions including free rotating and rotating cylinders exposed to the inner pressure. The effect of the angular velocity is investigated on the radial distribution of various components. The mentioned structure can be considered as a sensor for measuring the angular velocity of the cylinder subjected to the pressure and temperature. The obtained results indicate that the electrical potential is proportional to the angular velocity.     

Experimental and numerical study of an aquaculture net cage with floater in waves and current

The mooring loads on an aquaculture net cage in current and waves are investigated by dedicated model tests and numerical simulations. The main purpose is to investigate which physical effects are dominant for mooring loads, and in this respect, to investigate the validity of different rational hydrodynamic load models. Also structural and numerical aspects are investigated. The model tests are performed to provide benchmark data, while the numerical model is used to study the effect and sensitivity of different load models and parameters.Compared to a realistic aquaculture plant, the total system is simplified to reduce the complexity. The system does, however, include all the four main components of an aquaculture plant: net cage, floater, sinker weights and moorings. The net cage is bottomless, flexible and circular. It is attached to a circular, elastic floater at the top and has 16 sinker weights at the bottom. The system is nearly linearly moored with four crow feet mooring lines.The loads are measured in the four mooring lines. A systematic variation of current only, wave only as well as combined current and wave conditions is carried out. The numerical simulation results are first benchmarked towards the experimental data. The mean loads in general dominate over the dynamic part of the loads in combined current and waves, and they significantly increase in long and steep waves, relative to current only. Next, a sensitivity study is carried out. A rigid floater significantly alters the loads in the mooring lines compared to a realistic, elastic floater. The theoretical model for the wave matters. The mooring loads are rather insensitive to a majority of the parameters and models, in particular: frequency dependent added mass of the floater and nonlinear restoring loads. It seems not to be necessary to represent the net cage with a very fine numerical mesh.     

复合材料层合板1:1参数共振的分岔研究

针对复合材料对称铺设各向异性矩形层合板的物理模型,在同时考虑了材料、阻尼和几何等非线性因素后,建立了二自由度非线性参数振动系统动力学控制方程,并应用多尺度法求得基本参数共振下的近似解析解,利用数值模拟分析了系统的分岔和混沌运动.指出了伽辽金截断对系统动力学分析的影响,以及系统进入混沌的途径.     

Calculating the Time to Creep Failure of Thin-Walled Pipes under Internal Pressure

The time to failure is calculated for thin-walled pipes subjected to internal pressure, to internal pressure and tension, and to internal pressure and bending. The problems are solved using the concept of equivalent stresses. The equivalent stresses are found from a mixed delayed-failure criterion relating the maximum normal stress and the intensity of tangent stresses. The criterion includes an additional material constant, which is determined experimentally. The calculated results and experimental data are compared and found to be in satisfactory agreement     

Water flow between soil aggregates

Aggregated soils are structured systems susceptible to non-uniform flow. The hydraulic properties depend on the aggregate fabric and the way the aggregates are assembled. We examined the hydraulic behavior of an aggregate packing. We focused on conditions when water mostly flows through the aggregates, leaving the inter-aggregate pore space air-filled. The aggregates were packed in 3 mm thick slabs forming a quasi two-dimensional bedding. The larger aggregates were wetted with water and embedded in smaller aggregates equilibrated at a lower water content. The water exchange between wet and drier aggregates was monitored by neutron radiography. The three-dimensional arrangement of the aggregates was reconstructed by neutron tomography. The water flow turned out to be controlled by the contacts between aggregates, bottle-necks that slow down the flow. The bottle-neck effect is due to the narrow flow cross section of the contacts. The water exchange was simulated by considering the contact area between aggregates as the key parameter. In order to match the observed water flow, the contact area must be reduced by one to two orders of magnitude relative to that obtained from image analysis. The narrowness of the contacts is due to air-filled voids within the contacts.     

Lubrication analysis of a cell sliding into a circular pore

The resistance to the blood cells at the entrance to capillaries and membrane pores contributes considerably to the peripheral resistance in the blood circulation. This paper proposes, for the first time, a simplified mechanical model in an attempt to treat the axisymmetric motion of a cell sliding into a circular pore. In this model, the shape of the cell is taken as given according to the microvideograph and the cell membrane is assumed to slide over its surface. The lubrication theory is applied to the thin layers of plasma between the membrane and the pore wall, yielding the pressure and shear stress distributions over the membrane as well as the resultant drag exerted on the cell. Our computations have simulated the process of the cell entering the pore, which is in qualitative agreement with the microvideographic observations.The Project Supported by National Natural Science Foundation of China.The authors wish to express their thanks to Professor S. Weinbaum of The City University of New York for his enlightening suggestions on the mechanical model of this problem during his visit to Peking University. The authors are also grateful to Professor Li Gui-shan of Institute of blood. The Chinese Academy of Medical Sciences, for providing the relevant microvideographes.     

Experimental Study and Fractal Analysis of Heterogeneity in Naturally Fractured Rocks

Capillary pressure curves of six low porosity and low permeability core samples from The Geysers geothermal field were measured using the mercury-intrusion approach to characterize the heterogeneity of rock. One high permeability Berea sandstone core sample was analyzed similarly, for comparison. The maximum pressure of mercury intruded into the rock was about 200 MPa to reach the extremely small pores. Experimental data showed that the capillary pressure curves of The Geysers rock are very different from that of the Berea sandstone. It was found that the frequently used capillary pressure models could not be used to represent the data from The Geysers rock samples. This might be because of the fractures in the rock. To this end, a fractal technique was proposed to model the features of the capillary pressure curves and to characterize the difference in heterogeneity between The Geysers rock and Berea sandstone. The results demonstrated that the rock from The Geysers geothermal field was fractal over a scaling range of about five orders of magnitude. The values of the fractal dimension of all the core samples (six from The Geysers and one Berea sandstone) calculated using the proposed approach were in the range from 2 to 3. The results showed that The Geysers rock with a high density of fractures had a greater fractal dimension than Berea sandstone which is almost without fractures. This shows that The Geysers rock has greater heterogeneity, as expected.     

Numerical simulation of the unsteady behaviour of cavitating flows

A 2D numerical model is proposed to simulate unsteady cavitating flows. The Reynolds‐averaged Navier–Stokes equations are solved for the mixture of liquid and vapour, which is considered as a single fluid with variable density. The vapourization and condensation processes are controlled by a barotropic state law that relates the fluid density to the pressure variations. The numerical resolution is a pressure‐correction method derived from the SIMPLE algorithm, with a finite volume discretization. The standard scheme is slightly modified to take into account the cavitation phenomenon. That numerical model is used to calculate unsteady cavitating flows in two Venturi type sections. The choice of the turbulence model is discussed, and the standard RNG k–εmodel is found to lead to non‐physical stable cavities. A modified k–εmodel is proposed to improve the simulation. The influence of numerical and physical parameters is presented, and the numerical results are compared to previous experimental observations and measurements. The proposed model seems to describe the unsteady cavitation behaviour in 2D geometries well. Copyright © 2003 John Wiley & Sons, Ltd.     

Fractional Derivatives Applied to Phase-Space Reconstructions

The concept and application of phase-space reconstructions are reviewed. Fractional derivatives are then proposed for the purpose of reconstructing dynamics from a single observed time history. A procedure is presented in which the fractional derivatives of time series data are obtained in the frequency domain. The method is applied to the Lorenz system. The ability of the method to unfold the data is assessed by the method of global false nearest neighbors. The reconstructed data is used to compute recurrences and correlation dimensions. The reconstruction is compared to the commonly used method of delays in order to assess the choice of reconstruction parameters, and also the quality of results.