Enhanced Performance of Quasi‐Solid‐State Dye‐Sensitized Solar Cells by Branching the Linear Substituent in Sensitizers Based on Thieno[3,4‐c]pyrrole‐4,6‐dione

Thieno[3,4‐c]pyrrole‐4,6‐dione‐based organic sensitizers with triphenylamine ( FNE38 and FNE40 ) or julolidine ( FNE39 and FNE41 ) as electron‐donating unit have been designed and synthesized. A linear hexyl group or a branched alkyl chain, the 2‐ethylhexyl group, is incorporated into molecular skeleton of the dyes to minimize intermolecular interactions. The absorption, electrochemical, and photovoltaic properties for these sensitizers were then systematically investigated. It is found that the sensitizers have similar photophysical and electrochemical properties, such as absorption spectra and energy levels, owing to their close chemical structures. However, the quasi‐solid‐state dye‐sensitized solar cells (DSSCs) based on the two types of sensitizers exhibit very different performance parameters. Upon the incorporation of the short ethyl group on the hexyl moiety, enhancements in both open‐circuit voltage (V_oc) and short‐circuit current (J_sc) are achieved for the quasi‐solid‐state DSSCs. The V_oc gains originating from the suppression of charge recombination were quantitatively investigated and are in good agreement with the experimentally observed V_oc enhancements. Therefore, an enhanced solar energy conversion efficiency (η) of 6.16 %, constituting an increase by 23 %, is achieved under standard AM 1.5 sunlight without the use of coadsorbant agents for the quasi‐solid‐state DSSC based on sensitizer FNE40 , which bears the branched alkyl group, in comparison with that based on FNE38 carrying the linear alkyl group. This work presents a design concept for considering the crucial importance of the branched alkyl substituent in novel metal‐free organic sensitizers.     

The effect of tuning chemical structure on the open-circuit voltage and photovoltaic performance of narrow band-gap polymers

Most of the narrow band-gap polymers exhibit low open-circuit voltage (V_oc) which limits the further improvement of photovoltaic performance. How to improve the V_oc through fine tuning of the chemical structure is a significant project that worth exploring. As a big and strong electron accepting unit, fluorinated-quinoxaline based copolymers always show a narrow band gap and broad absorption which makes it a good template to study the changes of V_oc through structure tuning. In this work, the effect of the subtle chemical structure modulation of polymer side chains and main chain on the V_oc and photovoltaic performance was investigated. The V_oc was adjusted effectively, and the power conversion efficiency (PCE) also was improved simultaneously. Although the PCE was not high enough as those high-performance polymers reported at present, the result indicates that fine tuning of chemical structure is an effective way to improve V_oc and photovoltaic performance for narrow band-gap polymers. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2017 , 55, 699–706     

Effect of valence state of vanadium on stereoblock polymerization of methyl methacrylate with VOCl3–AlEt2Br catalyst system

The polymerization of methyl methacrylate with the VOCL₃–ALEt₂Br catalyst system in n-hexane has been studied. The first-order dependence of rate of polymerization on catalyst and monomer concentrations, activation energy of 6.67 kcal/mole, and NMR spectra of polymer lend support to a coordinate anionic mechanism of polymerization. It has been shown that the vanadium in V⁺² oxidation state is less active than V⁺³ oxidation state of active complex.     

Investigation of Electron Behavior in Nano‐TiO2 Photocatalysis by Using In Situ Open‐Circuit Voltage and Photoconductivity Measurements

The in situ open‐circuit voltages (V_oc) and the in situ photoconductivities have been measured to study electron behavior in photocatalysis and its effect on the photocatalytic oxidation of methanol. It was observed that electron injection to the conduction band (CB) of TiO₂ under light illumination during photocatalysis includes two sources: from the valence band (VB) of TiO₂ and from the methanol molecule. The electron injection from methanol to TiO₂ is slower than that directly from the VB, which indicates that the adsorption mode of methanol on the TiO₂ surface can change between dark and illuminated states. The electron injection from methanol to the CB of TiO₂ leads to the upshift of the Fermi level of electrons in TiO₂, which is the thermodynamic driving force of photocatalytic oxidation. It was also found that the charge state of nano‐TiO₂ is continuously changing during photocatalysis as electrons are injected from methanol to TiO₂. Combined with the apparent Langmuir–Hinshelwood kinetic model, the relation between photocatalytic kinetics and electrons in the TiO₂ CB was developed and verified experimentally. The photocatalytic rate constant is the variation of the Fermi level with time, based on which a new method was developed to calculate the photocatalytic kinetic rate constant by monitoring the change of V_oc with time during photocatalysis.     

Photoelectrochemical Complexes of Fucoxanthin‐Chlorophyll Protein for Bio‐Photovoltaic Conversion with a High Open‐Circuit Photovoltage

Open‐circuit photovoltage (V_oc ) is among the critical parameters for achieving an efficient light‐to‐charge conversion in existing solar photovoltaic devices. Natural photosynthesis exploits light‐harvesting chlorophyll (Chl) protein complexes to transfer sunlight energy efficiently. We describe the exploitation of photosynthetic fucoxanthin‐chlorophyll protein (FCP) complexes for realizing photoelectrochemical cells with a high V_oc . An antenna‐dependent photocurrent response and a V_oc up to 0.72 V are observed and demonstrated in the bio‐photovoltaic devices fabricated with photosynthetic FCP complexes and TiO₂ nanostructures. Such high V_oc is determined by fucoxanthin in FCP complexes, and is rarely found in photoelectrochemical cells with other natural light‐harvesting antenna. We think that the FCP‐based bio‐photovoltaic conversion will provide an opportunity to fabricate environmental benign photoelectrochemical cells with high V_oc , and also help improve the understanding of the essential physics behind the light‐to‐charge conversion in photosynthetic complexes.     

A Pentacyclic Nitrogen‐Bridged Thienyl–Phenylene–Thienyl Arene for Donor–Acceptor Copolymers: Synthesis,Characterization, and Applications in Field‐Effect Transistors and Polymer Solar Cells

A pentacyclic benzodipyrrolothiophene ( BDPT ) unit, in which two outer thiophene rings are covalently fastened with the central phenylene ring by nitrogen bridges, was synthesized. The two pyrrole units embedded in BDPT were constructed by using one‐pot palladium‐catalyzed amination. The coplanar stannylated Sn‐BDPT building block was copolymerized with electron‐deficient thieno[3,4‐c]pyrrole‐4,6‐dione ( TPD ), benzothiadiazole ( BT ), and dithienyl‐diketopyrrolopyrrole ( DPP ) acceptors by Stille polymerization. The bridging nitrogen atoms make the BDPT motif highly electron‐abundant and structurally coplanar, which allows for tailoring the optical and electronic properties of the resultant polymers. Strong photoinduced charge‐transfer with significant band‐broadening in the solid state and relatively higher oxidation potential are characteristic of the BDPT‐based polymers. Poly(benzodipyrrolothiophene‐alt‐benzothiadiazole) ( PBDPTBT ) achieved the highest field‐effect hole mobility of up to 0.02 cm² V^?1 s^?1. The photovoltaic device using the PBDPTBT /PC₇₁BM blend (1:3, w/w) exhibited a V_oc of 0.6 V, a J_sc of 10.34 mA cm^?2, and a FF of 50 %, leading to a decent PCE of 3.08 %. Encouragingly, the device incorporating poly(benzodipyrrolothiophene‐alt‐thienopyrrolodione) ( PBDPTTPD )/PC₇₁BM (1:3, w/w) composite delivered a highest PCE of 3.72 %. The enhanced performance arises from the lower‐lying HOMO value of PBDPTTPD to yield a higher V_oc of 0.72 V.     

Influence of Solvent and Bridge Structure in Alkylthio‐Substituted Triphenylamine Dyes on the Photovoltaic Properties of Dye‐Sensitized Solar Cells

Three new triphenylamine dyes that contain alkylthio‐substituted thiophenes with a low bandgap as a π‐conjugated bridge unit were designed and synthesized for organic dye‐sensitized solar cells (DSSCs). The effects of the structural differences in terms of the position, number, and shape of the alkylthio substituents in the thiophene bridge on the photophysical properties of the dye and the photovoltaic performance of the DSSC were investigated. The introduction of an alkylthio substituent at the 3‐position of thiophene led to a decrease in the degree of redshift and the value of the molar extinction coefficient of the charge‐transfer band, and the substituent with a bridged structure led to a larger redshift than that of the open‐chain structure. The introduction of bulky and hydrophobic side chains decreased the short‐circuit photocurrent (J_sc), which was caused by the reduced amount of dye adsorbed on TiO₂. This resulted in a decrease in the overall conversion efficiency (η), even though it could improve the open‐circuit voltage (V_oc) due to the retardation of charge recombination. Furthermore, the change in solvents for TiO₂ sensitization had a critical effect on the performance of the resulting DSSCs due to the different amounts of dye adsorbed. Based on the optimized dye bath and molecular structure, the ethylene dithio‐substituted dye ( ATT3 ) showed a prominent solar‐to‐electricity conversion efficiency of 5.20 %.     

Absorption and emission properties of 5-phenyl tris(8-hydroxyquinolinato) M(III) complexes (M = Al,Ga, In) and correlations with molecular electrostatic potential

Substituent effect for a series of 5-phenyl tris(8-hydroxyquinolinato) M(III) complexes (Mq3) of aluminum, gallium, and indium are investigated using density functional theory (DFT) for the ground state properties and the time-dependent version of DFT (TDDFT) for their absorption and emission properties. A comparison between the ground state energy of mer and fac isomers of all the complexes revealed that the mer configuration is always more stable than fac. The substituent effect is significantly reflected at the fluorescence maximum (λ_F) values whereas the effect is moderate at the absorption maximum (λ_abs) values. The molecular electrostatic potential (MESP) at the metal center (V_M) and the most electron rich region indicated by MESP minimum (V_min), located at the oxygen of phenoxide ring exhibit excellent correlations with the λ_F and Stokes shift (λ_F−λ_abs) values. The study suggests the use of Stokes shift as an experimental quantity to measure the excited state substituent effect while the V_min or V_M emerge as theoretical quantities to measure the same.     

Novel low‐bandgap oligothiophene‐based donor‐acceptor alternating conjugated copolymers: Synthesis,properties, and photovoltaic applications

A series of novel soluble donor‐acceptor low‐bandgap‐conjugated polymers consisting of different oligothiophene (OTh) coupled to electron‐accepting moiety 2‐pyran‐4‐ylidenemalononitrile (PM)‐based unit were synthesized by Stille or Suzuki coupling polymerization. The combination of electron‐accepting PM building block with varied OTh_n (the number of thiophene unit increases from 3 to 5) results in enhanced π–π stacking in solid state and intramolecular charge transfer (ICT) transition, which lead to an extension of the absorption spectra of the copolymers. Cyclic voltammetry measurements and molecular orbital distribution calculations indicate that the highest occupied molecular orbitals (HOMO) energy levels could be fine‐tuned by changing the number of thiophene units of the copolymers, and the resulting copolymers possessed relatively low HOMO energy levels promising good air stability and high‐open circuit voltage (V_oc) for photovoltaic application. Bulk heterojunction photovoltaic devices were fabricated by using the copolymers as donors and (6,6)‐phenyl C₆₁‐butyric acid methyl ester as acceptor. It was found that the highest V_oc reached 0.94 V, and the short circuit currents (J_sc) were improved from 1.78 to 2.54 mA/cm², though the power conversion efficiencies of the devices were measured between 0.61 and 0.99% under simulated AM 1.5 solar irradiation of 100 mW/cm², which indicated that this series copolymers can be promising candidates for the photovoltaic applications. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 2765–2776, 2010     

Dyes and Redox Couples with Matched Energy Levels: Elimination of the Dye‐Regeneration Energy Loss in Dye‐Sensitized Solar Cells

In dye‐sensitized solar cells (DSSCs), a significant dye‐regeneration force (ΔG_reg⁰≥0.5 eV) is usually required for effective dye regeneration, which results in a major energy loss and limits the energy‐conversion efficiency of state‐of‐art DSSCs. We demonstrate that when dye molecules and redox couples that possess similar conjugated ligands are used, efficient dye regeneration occurs with zero or close‐to‐zero driving force. By using Ru(dcbpy)(bpy)₂²⁺ as the dye and Ru(bpy)₂(MeIm)₂^3+//2+ as the redox couple, a short‐circuit current (J_sc) of 4 mA cm^?2 and an open‐circuit voltage (V_oc) of 0.9 V were obtained with a ΔG_reg⁰ of 0.07 eV. The same was observed for the N3 dye and Ru(bpy)₂(SCN)₂^1+/0 (ΔG_reg⁰=0.0 eV), which produced an J_sc of 2.5 mA cm^?2 and V_oc of 0.6 V. Charge recombination occurs at pinholes, limiting the performance of the cells. This proof‐of‐concept study demonstrates that high V_oc values can be attained by significantly curtailing the dye‐regeneration force.     

Benzodithiophene-Fused Perylene Bisimides as Electron Acceptors for Non-Fullerene Organic Solar Cells with High Open-Circuit Voltage

Tandem-junction organic solar cells require solar cells with visible light photo-response as front cells, in which an open-circuit voltage (V_oc) above 1.0 V is highly demanded. In this work, we are able to develop electron acceptors to fabricate non-fullerene organic solar cells (NFOSCs) with a very high V_oc of 1.14 V. This was realized by designing perylene bisimide (PBI)-based conjugated materials fused with benzodithiophene, in which Cl and S atom were introduced into the molecules in order to lower the frontier energy levels. The fused structures can reduce the aggregation of PBI unit and meanwhile maintain a good charge transport property. The new electron acceptors were applied into NFOSCs by using Cl and S substituted conjugated polymers as electron donor, in which an initial power conversion efficiency of 6.63 % and a high V_oc of 1.14 V could be obtained. The results demonstrate that the molecular design by incorporating Cl and S atom into electron acceptors has great potential to realize high performance NFOSCs.     

Pseudo-One-Coordinate Tetrylenium Salts Bearing a Bulky Carbazolyl Substituent

Syntheses of a bulky carbazole-based substituent, the parent 1,8-bis(3,5-di-tert-butylphenyl)-3,6-di-tert-butyl-carbazole (R−H) and a series of chlorotetrylenes, RECl (E=Ge, Sn, Pb), are described. Detailed analysis of the properties of the carbazole-based substituent revealed that it features flexible high bulkiness and electronic non-innocence, which may make it suitable for many applications in both main-group and transition-metal chemistry. To further showcase the employability of the novel substituent, the chlorotetrylenes were subjected to halide abstraction reactions, affording the corresponding tetrylenium salts [RE][Al(OC₄F₉)₄] (E=Ge, Sn, Pb) as strongly coloured compounds.     

The side chain effects on TPD-based copolymers: the linear chain leads to a higher jsc

Abstract

Alkyl substituents appended to polymers play the determining role on self-assembly and film-forming properties, and on device performance. In this work, we highlight the effects of the linear and branched flexible chains appended to the acceptor moiety (A) in D-A type copolymers. Two thieno[3,4-c]-pyrrole-4,6-dione (TPD) based copolymers PT1 and PT2 with different alkyl chains, were designed and synthesized. By comparison their UV-vis absorptions, HOMO/LUMO energy levels, as well as the characters in polymer solar cells, the influences of alkyl chains were investigated. Both copolymers showed molecular weights of 21?kDa and similar optical properties with a medium band gap of 1.93?eV, while PT2 with the branched chain exhibited a lower HOMO than that of PT1 (?5.43 vs???5.37?eV). In bulk heterojunction (BHJ) solar cells, PT1 with a linear chain presented a short circuit current (J_sc) of 6.76?mA cm^?2, open circuit voltage (V_oc) of 0.89?V and power conversion efficiency (PCE) of 2.92%. To the contrary, PT2 showed a J_sc of 3.53?mA cm^?2, V_oc of 0.99?V, delivering a relatively lower PCE of 2.05%. The result indicates that appending a linear alkyl chain to the TPD unit could sufficient enhance the J_sc value of the related polymer.     

Synthesis and Photovoltaic Properties of Formyl End-Capped Oligothiophenes

For the purpose of developing novel photovoltaic materials, 5,5″-biformyl-2,2′:5′,2″-terthiophene (OHC-3T-CHO) and 5,5″″-biformyl-2,2′:5′,2″:5″,2″′:5″′,2″″-q-uinquethiophene (OHC-5T-CHO) were synthesized. The photovoltaic properties of OHC-3T-CHO and OHC-5T-CHO were studied. We have fabricated two flexible organic photovoltaic devices using OHC-3T-CHO, OHC-5T-CHO, and 3,4,9,10-perylenetetracarboxylic dianhydride (PTCDA). The PET-ITO (indium tin oxides coated with polyethylene terephthalate)/OHC-3T-CHO/PTCDA/Al device has an open circuit voltage (V _oc ) of 1.12 V, and photoelectric conversion efficiency (PCE) of 1.00%, whereas the PET-ITO/OHC-5T-CHO/PTCDA/Al device has a V _oc of 1.78 V and PCE of 1.08%. Both devices have high V _oc (1.12 V and 1.78 V). It is possible that intermolecular hydrogen bonding between the –CHO group of OHC-nT-CHO and the carboxylic dianhydride of PTCDA enhanced the efficiency by promoting forward interfacial electron transfer.     

Dye-sensitised solar cells with iodine-free discotic electrolytes

Discotic mesogenic molecules viz., hexahexylthiotriphenylene (HHTT) and hexahexyloxytriphenylene were applied, for the first time, as iodine-free redox electrolyte in dye-sensitised solar cells (DSSCs). The cell shows open circuit voltage (V_oc) of 0.95 V, short circuit current density (J_sc) of 0.534 mA/cm², fill factor 88.24% and overall power conversion efficiency (η) 0.45% in a typical fluorine doped tin oxide/TiO₂/N719/HHTT/Pt DSSC configuration. Scanning electron microscopy was used to study surface profile of electrolytes while electrochemical impedance spectroscopy was used to understand the electrochemical behaviour of electrolytes. The photovoltaic parameters were measured under standard conditions using Oriel solar simulator class AAA. These first results demonstrate the potential of the discotic molecules as charge transporter and mediator and show promise to be used in iodine-free DSSCs.     

Wide-Bandgap Perovskite Solar Cell Using a Fluoride-Assisted Surface Gradient Passivation Strategy

Wide-band gap (1.68 eV) perovskite solar cells (PSCs) are important components of perovskite/Si tandem devices. However, the efficiency of wide band gap PSCs has been limited by their huge open-circuit voltage (V_oc) deficit due to non-radiative recombination. Deep-level acceptor defects are identified as the major killers of V_oc, and they can be effectively improved by passivation with ammonium salts. Theoretical calculation predicts that increasing the distance between F and −NH₃⁺ of fluorinated ammonium can dramatically enhance the electropositivity of −NH₃⁺ terminals, thus providing strong adsorption onto the negatively charged I_A and I_Pb anti-site defects. Characterizations further confirm that surface gradient passivation employing p-FPEAI demonstrates the most efficient passivation effect. Consequently, a record-efficiency of 21.63 % with the smallest V_oc deficit of 441 mV is achieved for 1.68 eV-band gap inverted PSCs. Additionally, a flexible PSC and 1 cm² opaque device also deliver the highest PCEs of 21.02 % and 19.31 %, respectively.     

Effect of para-Substituents on meso-Functionalized Oxidovanadium(IV) Porphyrins as Catalysts for Oxygen Atom Transfer Mediated Oxidation of Benzoin to Benzil under Mild Conditions

Systematic analysis of the effect of para-substituents (H, Cl, Br and OMe) on the meso-phenyl group in vanadyl meso-tetraphenylporphyrins ([V^IVO(TPP)] (R=H, 1 ), [V^IVO(TCPP)] (R=Cl, 2 ), [ V^IVO(TBPP)] (R=Br, 3 ) and [V^IVO(TMPP)] (R=OMe, 4 )) on their properties and catalytic oxygen atom transfer (OAT) for oxidation of benzoin to benzil using DMSO as well as 30 % aqueous H₂O₂ as the sacrificial oxygen source have been studied. Electrochemical and theoretical (density functional theory) studies are in good agreement with the influence of these substituents on the catalytic property of these complexes. Complex [V^IVO(TCPP)] ( 2 ) displayed the best catalytic activity for the conversion (92 %) of benzoin to benzil in 30 h with >99 % product selectivity when DMSO was used as an oxygen source, whereas excellent conversion (~100 %) of benzoin to benzil was noticed in 18 h with 95 % product selectivity when 30 % aqueous H₂O₂ was used as a source of oxygen. Furthermore, among these complexes, the electron-withdrawing nature of the chloro substituent at the p-position of meso-phenyl group significantly influences the oxygen atom transfer. Experimental and simulated EPR studies confirmed the +4 oxidation of vanadium in these complexes. The structure of 2 , 3 and 4 , confirmed by single crystal X-ray diffraction method, are domed in shape, and the displacement of V(IV) ion from the mean porphyrin plane follows the order: 2 (0.458 Å) < 3 (0.459 Å) < 4 (0.479 Å). We observed that the electron-withdrawing nature of chloro substituent at the p-position of meso-phenyl group influence the oxygen atom transfer from vanadyl porphyrin to dimethyl sulfide much.     

Effect of position of the lateral fluoro substituent on the mesophase behaviour of aryl 4-alkoxyphenylazo benzoates in pure and binary mixtures

Five groups of 4-substituted phenyl 4?-(2?- (or 3″-) substituted-4?-alkoxyphenylazo) benzoates (In_a-c to Vn_a-c) were investigated in which, within each group, the length of the terminal alkoxy group varies between 8 and 16 carbons, while the other terminal substituent, X, is a polar group that alternatively changed between the electron-donating CH₃O and the electron-withdrawing Br group, in addition to the un-substituted analogue (X = H). The lateral substituent (Y) in the five groups I–V varies, respectively, between H, 3-CH₃, 2-CH₃, 3-F and 2-F. Their mesophase stabilities were determined by differential scanning calorimetry and phases identified by polarised light microscopy. The two newly prepared groups of compounds (IVn_a-c and Vn_a-c) are structurally characterised by infrared, ¹H-NMR, mass spectroscopy, thermogravimetric and elemental analyses. Binary phase diagrams were constructed for each pair of isomers from groups IV and V bearing the same wing substituents but the lateral F is attached to different positions (2? or 3″).     

Preparation and characterization of solution processable phthalocyanine‐containing polymers via a combination of RAFT polymerization and post‐polymerization modification techniques

In this work, a benzenedinitrile functionalized monomer, 2‐methyl‐acrylic acid 6‐(3,4‐dicyano‐phenoxy)‐hexyl ester, was successfully polymerized via the reversible addition‐fragmentation chain transfer method. The polymerization behavior conveyed the characteristics of “living”/controlled radical polymerization: the first‐order kinetics, linear increase of number‐average molecular weight with monomer conversion, narrow molecular weight distribution, and successful chain‐extension experiment. The soluble Zn(II) phthalocyanine (Pc)‐containing (ZnPc) polymers were achieved by post‐polymerization modification of the obtained polymers. The Zn(II) phthalocyanine‐functionalized polymer was characterized by FTIR, UV–vis, fluorescence, atomic absorption spectroscopy, and thermogravimetric analysis. The potential application of above ZnPc‐functionalized polymer as electron donor material in bulk heterojunction organic solar cell was studied. The device with ITO/PEDOT:PSS/ZnPc‐Polymer/PC₆₁BM/LiF/Al structure provided a power conversion efficiency of 0.014%, fill factor of 0.24, open circuit voltage (V_oc) of 0.21 V, and short‐circuit current (J_sc) of 0.28 mA/cm². © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 691–698