Molecular composite films from polybenzoxazole and crosslinked polymer matrixes

Films consisting of a rigid-rod polymer and thermoset resin matrixes were prepared. Poly{(benzo[1,2-d : 5,4-d′]bis(oxazole-2,6-diyl))-1,4-phenylene} (PBO) in polyphosphoric acid (PPA) was blended with 2,6-bis(4-benzocyclobutene) benzo[1,2- d : 5,4-d′]bis(oxazole) ( 1 ), and films were extruded from these solutions. The coagulated films were soluble in methanesulfonic acid (MSA). After heat treatment at 300°C, the films became insoluble in MSA. Crosslinked films were homogeneous and did not show phase segregation between the two components. These were composite films at the molecular level. Transmission electron microscopy (TEM) showed enhanced interlayer integrity and reduced microfibril separation for the molecular composite films as compared to normal PBO film. These films had significantly better torsion and tension delamination resistance. The incorporation of a second component did not sacrifice the tensile properties of PBO film. Thermal stability of these composite films was only slightly lower than that of normal PBO film. © 1997 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 35 : 2157–2165, 1997     

A study of benzobisoxazole and benzobisthiazole compounds and polymers under hydrolytic conditions

The stability of benzobisoxazole and benzobisthiazole compounds and polymers under hydrolytic conditions was studied. 2,6-Bis(4-tert-butylphenyl)benzo[1,2-d;4,5-d′]bisoxazole (1) dissolved in acetonitrile containing sulfuric acid and water at 80°C is stable. A suspension of 2,6-bis[4-(2-benzoxazoyl)phenyl]benzo[1,2-d;5,4-d′]bisoxazole (2) in 0.2 N H₂SO₄ or 0.2 N NaOH solution at 100°C for 21 days is stable. The intrinsic viscosity of a poly(p-phenylene)benzobisoxazole (PBO) fiber sample soaked in 0.2 N H₂SO₄, water with 1 wt % polyphosphoric acid (PPA), or 0.2 N NaOH remained the same. Under very severe hydrolytic conditions such as dissolution of compound 2 or PBO in PPA or methanesulfonic acid with residual water followed by coagulation in water, benzobisoxazole underwent bond cleavage to generate carboxylic acid and o-aminophenol functional groups. This is in contrast to an earlier hypothesis that the decrease in intrinsic viscosity under these conditions was due to chain association. Poly(p-phenylene)benzobisthiazole (PBT) also underwent bond cleavage under these very severe conditions, which are unlikely to be encountered in normal applications. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 2637–2643, 1999     

Synthesis of polyamides by ring-opening polyaddition of benzobis[1,2]oxazinediones with aliphatic diamines

Novel oxime-containing polyamides have been prepared by the ring-opening polyaddition of combinations of two benzobis[1,2]oxazinediones, 4,6-diphenylbenzo[1,2-d:5,4-d′]bis[1,2]oxazine-1,9-dione and 4,9-diphenylbenzo[1,2-d:4,5-d′]bis[1,2]oxazine-1,6-dione, with two aliphatic diamines in a polar aprotic solvent such as N-methyl-2-pyrrolidone. The polymerization was almost completed within a day at room temperature. These polymers had inherent viscosities in the range of 0.12–0.38 and were soluble in a wide range of solvents, including formic acid and hot m-cresol, as well as a number of polar aprotic solvents. All the polymers softened at a temperature ranging from 165 to 185°C. Thermal characterization of the polyamides by TGA and DTA showed polymer decomposition temperatures of about 240°C in air.     

Poly(p-Phenylenebenzobisoxazole) fiber with polyphenylene sulfide pendent groups

Poly(p-phenylenebenzobisoxazole) (PBO) fiber with polyphenylene sulfide (PPS) pendent groups was made to improve PBO fiber compressive strength by crosslinking. PPS moieties allowed the polymeric network to crosslink at heat-treatment temperatures at which PBO does not thermally degrade. PBO-PPS fiber heat-treated for 30 s at 600°C did not dissolve or break up in methanesulfonic acid. Compressive strength of crosslinked fiber was about 20% better than that of unmodified PBO fiber. In another experiment, 10 mol % of 2,5-diphenylsulfideterephthalic acid was incorporated into PBO fiber. The side chain of one phenyl sulfide unit was too short to enhance crosslinking, and the fiber had about the same compressive strength as unmodified PBO fiber. © 1995 John Wiley & Sons, Inc.     

2,6-二(对氨基苯)苯并[1,2-d;5,4-d']二噁唑的合成

以4,6-二氨基间苯二酚二磷酸盐和对氨基苯甲酸为原料,在多聚磷酸中,添加还原剂SnCl_2·2H_2O,经缩聚反应合成了有机二胺单体——2,6-二(对氨基苯)苯并[1,2-d;5,4-d']二噁唑(DIABO),其结构经~1H NMR和FT-IR确证。最佳反应条件为:1 0.01 mol,PPA中P_2O_5质量分数为84%,SnCl_2·2H_2O用量为8 wt%,在氮气保护下于200℃反应4 h,产率97%。TG研究结果表明:DIABO的起始分解温度为401.0℃。     

SYNTHESIS OF BENZO[1,2-b: 5,4-b′]- DIFURANYL-TRIAZOLES, -OXADIAZOLES, -THIAZOLIDINONES, -THIADIAZOLES,AND THE USE OF DNA IN EVALUATION OF THEIR BIOLOGICAL ACTIVITY

Benzo[1,2-b:5,4-b′]difuran-2-carbohydrazides 5a, b were reacted with aryl or alkyl isothiocyanates to give the corresponding thiosemicarbazides 6a–h. Cyclization of the substituted thiosemicarbazides with sodium hydroxide led to the formation of benzo[1,2-b:5,4-b′]difuranyl-1,3,4-triazoles 7a–f. Desulfurization of thiosemicarbazides by mercuric oxide gave benzo[1,2-b:5,4-b′]difuranyl-1,3,4-oxadiazoles 8a–f. Treatment of thiosemicarbazides with ethyl bromoacetate or α-bromopropionic acid yielded benzo[1,2-b:5,4-b′]difuranyl-carbonyl-hydrazono-4-thiazolidinones 9a–f and 10a–f, respectively. Furthermore, the reaction of the thiosemicarbazides with phosphorus oxychloride gave benzo[1,2-b:5,4-b′]difuranyl-1,3,4-thiadiazoles 11a–f. Some compounds in this study were biologically evaluated for their ability to bind to DNA.     

Axial X-ray scattering on high-performance polymeric fibers

High-temperature polymers were spum from liquid-crystalline solutions into fibers of superior thermal stability and mechanical properties. Fibers of two extended-chain polymers poly(p-phenyleneterephthalamide), PPTA, and poly-2,5-benzoxazole, ABPBO, as well as a rod-like polymer poly(p-phenylenebenzobisoxazole), PBO, were examined by axial x-ray scattering. Both wide-angle scattering and small-angle scattering were performed with CuKα radiation aiming along the fiber axis (c-axis) for structural information on the a-b lattice plane. In addition to previously reported lattice structure, the PPTA fibers (Kevlar® 29, 49, and 149) showed strong [004] and a [022] reflections suggesting that segments of the PPTA molecules were transverse to the fiber axis. This unique fiber structure is more prominent and the void content is less for the PPTA fibers with higher tensile modulus, (i.e., Kevlar® 149 > Kevlar® 49 > Kevlar® 29). Similar measurements on thermally annealed ABPBO and PBO fibers showed no [00l], [h0l], or [0kl] reflection indicative of a truly uniaxial molecular orientation. Evidence of microfibrillar order was discovered for the Kevlar® fibers and the ABPBO fiber. Results of conventional x-ray scattering on these fibers were compared and reconciled. © 1994 John Wiley & Sons, Inc.     

The synthesis,characterization, and crystal structures of poly(2,6‐naphthalenebenzobisoxazole) and poly(1,5‐naphthalenebenzobisoxazole)

The rigid‐rod polymers, poly(2,6‐naphthalenebenzobisoxazole) (Naph‐2,6‐PBO) and poly(1,5‐naphthalenebenzobisoxazole) (Naph‐1,5‐PBO) were synthesized by high temperature polycondensation of isomeric naphthalene dicarboxylic acids with 4,6‐diaminoresorcinol dihydrochloride in polyphosphoric acid. Expectedly, these polymers were found to have high thermal as well as thermooxidative stabilities, similar to what has been reported for other polymers of this class. The chain conformations of Naph‐2,6‐PBO and Naph‐1,5‐PBO were trans and the crystal structures of Naph‐2,6‐PBO and Naph‐1,5‐PBO had the three‐dimensional order, although the axial disorder existed for both Naph‐2,6‐PBO and Naph‐1,5‐PBO. Naph‐2,6‐PBO exhibited a more pronounced axial disorder than Naph‐1,5‐PBO because of its more linear shape. The repeat unit distance for Naph‐2,6‐PBO (14.15 Å) was found to be larger compared with that of Naph‐1,5‐PBO (12.45 Å) because of the more kinked structure of the latter. The extents of staggering between the adjacent chains in the ac projection of the crystal structure were 0.25c and 0.23c for Naph‐2,6‐PBO and Naph‐1,5‐PBO, respectively. Naph‐1,5‐PBO has a more kinked and twisted chain structure relative to Naph‐2,6‐PBO. The kinked and twisted chain structure of Naph‐1,5‐PBO in the crystal seems to prevent slippage between adjacent chains in the crystal structure. The more perfect crystal structure of Naph‐1,5‐PBO may be due to this difficulty in the occurrence of the slippage. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 1948–1957, 2006     

Structural investigations on lewis acid mediated solubilization of poly(p-phenylenebenzobisthiazole) in an aprotic solvent

Investigations on aluminum chloride-mediated solubilization of poly(p-phenylenebenzo-bisthiazole), PBZT, in nitromethane revealed that, in general, dilute solutions of the polymer prepared in nitromethane with a large molar excess of the Lewis acid with respect to PBZT were relatively stable and thus suitable for processing into films and coatings via regeneration with hydroxylic nosolvents while polymer solutions with minimum stoichiometrically required (PBZT:AlCl₃ molar ratio 1:4) or marginal molar excess of AlCl₃ relative to PBZT tended to gel during handling. Structural studies on polymer–Lewis acid complex solutions were performed using ¹H and ²⁷Al NMR. ¹H NMR of the protonated structure of the model compound 2,6-diphenylbenzo [1,2-d:4,5-d′] bisthiazole was useful for confirming the ¹H NMR assignments of PBZT-AlCl₃ complex solution in CD₃NO₂. ²⁷Al NMR was particularly useful in probing the different tetrahedrally coordinated environments of the Al nucleus in the polymer solution, pointing to a complexation interaction between the polymer molecule and the Lewis acid and also between the solvent and the Lewis acid. Direct evidence in the solid state for the presence of a reversible electron donor–acceptor complex (EDA complex) was obtained from FTIR spectra of complexed films, isolated and handled in an inert atmosphere. The structural changes upon PBZT complexation caused significant frequencly shifts in both aromatic as well as heteroring stretching modes relative to PBZT itself, and intensity variations indicative of changes in the resonance configuration between the 1,4-phenylene moiety and the aromatic heterocyclic ring were also observed upon complexation. A preliminary comparison between the pristine PBZT fibers and regenerated PBZT by dilute solution viscometry indicates that the process results, to some extent, in polymer degradation leading to a decrease in the molecular weight of the polymer © 1993 John Wiley & Sons, Inc.     

Improvement of PBO fiber surface and PBO/PPESK composite interface properties with air DBD plasma treatment

The interface of fibrous composites is a key factor to the whole properties of the composites. In this study, the effects of air dielectric barrier discharge (DBD) plasma discharge power density on surface properties of poly(p‐phenylene benzobisoxazole) (PBO) fiber and the interfacial adhesion of PBO fiber reinforced poly(phthalazinone ether sulfone ketone) (PPESK) composite were investigated by several characterization methods, including XPS, SEM, signal fiber tensile strength, interlaminar shear strength, and water absorption. After the air DBD plasma treatment at a power density of 41.4 W/cm³, XPS analysis showed that some polar functional groups were introduced on the PBO fiber surface, especially the emergence of a new oxygen‐containing group (?O–C = O group). SEM observations revealed that the air DBD plasma treatment had a great influence on surface morphologies of the PBO fiber, while the signal fiber tensile strength results showed only a small decline of 5.9% for the plasma‐treated fiber. Meanwhile, interlaminar shear strength value of PBO/PPESK composite was increased to 44.71 MPa by 34.5% and water absorption of the composite decreased from 0.46% for the untreated specimen to 0.27%. The results showed that the air DBD plasma treatment can effectively improve the properties of the PBO fiber surface and the PBO/PPESK composite interface. Results obtained from the above analyses also showed that both the fiber surface and the composite interface performance would be reduced when an undue plasma discharge power density was applied. Copyright © 2011 John Wiley & Sons, Ltd.     

Improvement of surface wettability and interfacial adhesion ability of poly(p-phenylene benzobisoxazole) (PBO) fiber by incorporation of 2,5-dihydroxyterephthalic acid (DHTA)

By introducing 2,5-dihydroxyterephthalic acid (DHTA) into poly(p-phenylene benzoxazole) (PBO) macromolecular chains, dihydroxy poly(p-phenylene benzobisoxazole) (DHPBO) was synthesized and then DHPBO fibers were prepared by dry-jet wet-spinning method. Effects of hydroxyl polar groups on surface wettability and interfacial adhesion ability of PBO fiber were investigated. With the incorporation of double hydroxyl polar groups, contact angle on PBO fiber for water can decrease from 71.4° to 50.70°, and contact angle for ethanol can decrease from 37.2° to 27.40°. The wetting time on DHPBO fibers for water can be as short as 650 ms, which is half of that of PBO fibers. The interfacial shearing strength (IFSS) between DHPBO (10% mol content DHTA) fibers and epoxy resin is 18.87 MPa, 92.55% higher than that of PBO fibers. SEM images indicate that the PBO/epoxy composite failure mode may change from fiber/matrix adhesive failure to partially cohesive failure.     

Stress distribution in poly‐p‐phenylenebenzobisoxazole (PBO) fiber estimated from vibrational spectroscopic measurement under tension. II. Analysis of inhomogeneous stress distribution in PBO fiber

Fourier transform Raman spectra were measured for poly‐p‐phenylenebenzobisoxazole (PBO) fiber subjected to a tensile stress, and the Raman shift factor (the frequency shift caused by 1 GPa tensile stress) depended strongly on the sample‐preparation condition. To clarify the reasons of this dependency, a mechanical series parallel model was adopted that could successfully and quantitatively explain the observed Raman shift factors and gave a concreate heterogeneous stress distribution in the PBO fibers. As a result, a mechanical series model was reasonable for PBO fiber. Broadening of Raman bands, which was observed when the PBO fiber was tensioned, could also be interpreted on the basis of an idea of heterogeneous stress distribution. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 1281–1287, 2002     

苯并二噁唑系列聚合物的合成及表征

以4,6-二氨基-1,3-苯二酚盐酸盐为原料,分别和对苯二甲酸、1,4-萘二甲酸、2,6-萘二甲酸、2,5-噻吩二甲酸、4,4-′(1,2-二苯基乙烯)二甲酸在多聚磷酸介质中反应,合成单环的聚(1,4-亚苯基)苯并二噁唑(PBO)、稠环的聚(1,4-亚萘基)苯并二噁唑(1,4-PNBO)和聚(2,6-亚萘基)苯并二噁唑(2,6-PNBO)、杂环的聚(2,5-亚噻吩基)苯并二噁唑(PTBO)及含有两个苯环的聚-4,4′-亚(1,2-二苯乙烯基)苯并二噁唑(4,4′-PDPEBO).采用傅立叶红外光谱、热重分析、元素分析、特性黏数分析对系列聚合物进行了表征.研究结果表明PBO、1,4-PNBO、4,4-′PDPEBO、2,6-PNBO和PTBO 5种聚合物的耐热性能依次降低,特性黏数依次为25.40、16.76、20.63、15.38和14.63 dL/g.     

Facile sulfur‐assisted carbonylation of diaminoresorcinol with carbon monoxide

4,6‐Diaminoresorcinol, which is a raw material of ZYLON (PBO fiber), has an instability in air atmosphere. Therefore, very stable benzo[1,2‐d:5,4‐d']bis‐2(3H)‐oxazolone recognized a useful equivalent of 4,6‐diaminoresorcinol during the stages of production, storage, and transportation. By combining the sulfur‐assisted carbonylation of 4,6‐diaminoresorcinol dihydrochloride with carbon monoxide and triethylamine under 0.1 MPa at 20°C for 4 h in DMF with the oxidation of resulting hydrogen sulfide salt with molecular oxygen for 2 h, benzo‐[1,2‐d:5,4‐d']bis‐2(3H)‐oxazolone was obtained in a quantitative yield. Also, carbonylation of 2,5‐diaminohydroquinone dihydrochloride and 2,5‐diamino‐1,4‐benzenedithiol dihydrochloride was smoothly performed to give benzo[1,2‐d:4,5‐d']bis‐2(3H)‐oxazolone and benzo[1,2‐d:4,5‐d']bis‐2(3H)‐ thiazolone, respectively, in good to excellent yields under similar reaction conditions. Furthermore, 2,6‐dimercaptobenzo[1,2‐d:5,4‐d']bisoxazole, which is another equivalent of 4,6‐diaminoresorcinol, was obtained in excellent yield by the thiocarbonylation of 4,6‐diaminoresorcinol dihydro‐chloride with carbon disulfide in the presence of 1‐methylpyrrolidine at 20°C for 24 h in DMF. © 2011 Wiley Periodicals, Inc. Heteroatom Chem 23:111–116, 2012; View this article online at wileyonlinelibrary.com . DOI 10.1002/hc.20746     

Synthesis and Characterization of Poly(p-phenylene benzobisoxazole)/Poly(pyridobisimidazole) Block Copolymers

Poly(p-phenylene benzobisoxazole)/poly(pyridobisimidazole) block copolymers (PBO-b-PIPD) were prepared by introducing poly(pyridobisimidazole) (PIPD) moieties into the main chains of poly(p-phenylene benzobisoxazole) (PBO) in order to enhance its photostability. PBO and copolymer fibers were directly prepared from the polymerization solutions by dry-jet wet-spinning. Chemical structures and molecular chains arrangement of the block copolymers were characterized by Fourier transform infrared (FTIR) spectroscopy, solid-state ¹³C-NMR and wide angle X-ray diffraction (WAXD). Thermal stability of the copolymers was investigated by thermogravimetric analysis (TGA) in nitrogen. Thin films of PBO and copolymers were cast from methanesulfonic acid (MSA) solutions. Both the films and fibers were exposed to UV light to determine their photostability. Changes in the chemical structures and surface morphologies of the films were characterized by FTIR spectra and scanning electronic microscopy (SEM), respectively. After UV light exposure, the retention of strength for copolymer fibers is improved compared to PBO fibers. The results revealed that copolymers suffered less photodegradation in comparison with homopolymer. The mechanism for the improved photostability of the copolymers was discussed.     

In situ polymerization and characterization of graphene oxide‐co‐poly(phenylene benzobisoxazole) copolymer fibers derived from composite inner salts

A facile and efficient strategy for preparing well dispersed graphene oxide (GO)‐co‐Poly(phenylene benzobisoxazole) (PBO) copolymer fibers was carried out by direct in situ polycondensation of composite inner salts. The composite inner salts were achieved to improve the dispersivity, solubility, reactivity, and interfacial adhesion of GO in PBO polymer matrix. The structure and morphology of GO‐co‐PBO copolymer fibers have been characterized. It was demonstrated that GO were covalently incorporated with PBO molecular chains and dispersed considerably well in PBO fiber even the GO reach to 3 wt %. Meanwhile, the tensile modulus, tensile strength and thermal stability of GO‐co‐PBO copolymer fibers increased considerably with GO. The mechanism and theoretical calculation of GO enhanced PBO fiber were also discussed. The main reasons for the improvement on performance of PBO fiber should be attributed to good dispersion GO in PBO matrix and covalent bonding networks at the interface between GO and PBO molecular chains. © 2013 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2013     

化合物[2,6-bis(benzo[1,2-d:4,5-d′]diimidazole-2′-yl)pyridine] 的合成、晶体结构和光物理性质

A new tridentate benzimidazole derivative, 2,6-bis (benzo[1,2-d:4,5-d′]diimidazole-2′-yl) -pyridine (Bzdiimpy),was prepared from o-phenylenediamine in five steps with improved methods according to the literature in good yield.The crystal structure was determined by X-ray diffraction analysis. It crystallized in monoclinic, space group P21/c,with a=1.1708(4) nm, b=2.4796(9) nm, c=1.215 9(4) nm,β=114.641(7)°, Z=1, R=0.035 0, wR2=0.0890. The bzdiimp molecule displayed an almost planar structure and formed a zig-zag chain through weak interactions between imidazole-N and [SnCl6]2--Cl. Its electronic absorption and emission spectra were measured and compared with the reported analogue 2,6-bis (benz[1,2-d:4,5-d′]imidazole-2′-yl)-pyridine (Bzp).     

Thermally induced reorganization in LCP fibers

The molecular reorganization occurring in liquid crystalline polymer fiber during heat treatment is of great interest for many commercial reasons. Using thermal analysis techniques, WAXS and real time temperature dependent synchrotron SAXS, the structure and morphology of commercial LCP (liquid crystalline polymer), Vectran®, HBA/HNA (p-hydroxybenzoic acid/6-hydroxy-2-naphthoic acid), and its variant polymer fiber COTBP, HBA/HNA/BP/TA (BP-benzophenone, TA-terephthalic acid), have been examined. Both fibers have the typical liquid crystalline polymer structure, i.e., highly aligned with aperiodic sequencing along the fiber axis. There is a three-fold increase in strength in both fibers with heat treatment; however, the modulus is observed to increase significantly in COTBP but not in Vectran®. This paper reports on the changes and the differences on the structural and morphological behavior for both the as-spun and heat-treated LCP fibers. We propose an ‘oriented entanglement’ model to describe the differences between the two polymer fibers.     

Novel conjugated polymer poly(benzobisoxazole-2,6-diylvinylene): synthesis and evidence of aggregate formation in methanesulfonic acid

A new conjugated polymer poly(benzobisoxazole-2,6-diylvinylene) (PBOV) has been synthesized as an analogue of poly(p-phenylene benzobisoxazole) (PBO). The comparison between PBOV and PBO has been carried out by Fourier transform infrared spectroscopy, thermogravimetric analysis, UV, and photoluminescence (PL) spectroscopy. The UV absorption peaks, PL excitation and emission wavelengths of PBOV have a significant red-shift due to the better electronic delocalization. Similar to PBO, it can be observed in the PL spectra of PBOV at various concentrations in methanesulfonic acid (MSA) that the intensity of emission was depressed and the highly structured emission spectra gradually changed to featureless, red-shifted, and broad spectra with increasing concentration. The change in emission spectra can be attributed to the existence of the interchain aggregates, although PBOV does not show highly ordered structure as PBO does.     

Polybenzodipyrroloquinoxalines

Three polymers have been prepared by the condensation of benzo[1,2-b;5,4-b ′]-dipyrrolo-2,3,4,5-tetraone (I) with 1,2,4,5-tetraaminobenzene (II), 3,3 ′-diaminobenzidine (III), and 3,3 ′,4,4 ′-tetraaminodiphenyl ether (IV) in polyphosphoric acid (PPA) solution. The polymer structures were substantiated by comparison of their infrared and ultraviolet spectra with spectra of the model compounds and elemental analysis. The polymers had inherent viscosities of 0.86-0.90 (H₂SO₄) and thermal stabilities of 460°C and up to 700°C in air and nitrogen atmospheres, respectively.