Effect of the presence of polymer in miniemulsion droplets on the kinetics of polymerization

Solution of polystyrene in styrene were dispersed in an aqueous gel phase comprising sodium lauryl sulfate, cetyl alcohol, and water using an emulsification process known to produce monomer droplet sizes inthe submicron size range (referred to as miniemulsion droplets). The shelf-life stabilities of these miniemulsions were studied to determine their relative droplet sizes, and the emulsions were concommitantly polymerized in an isothermal batch reaction calorimeter. The polymerization kinetics and final particle sizes produced were compared with miniemulsion and conventional emulsion polymerizations prepared using equivalent recipes without the addition of polystyrene. The results indicate that polymerization of miniemulsions prepared from polymer solutions produce significantly different kinetics than both miniemulsion and conventional emulsion polymerizations. In general, a small amount of polymer greatly increases the rate of polymerization and the final number of particles produced in the polymerization to the extent where even conventional polymerizations carried out above the critical micelle concentration of the surfactant polymerize more slowly. The results are explained by considering the system to be comprised of small, stable pre-formed monomer-swollen polymer particles which are able to efficiently capture aqueous phase radicals. This enables the system to produce a large final number of particles, similar to the initial number of pre-formed polymer particles, as opposed to miniemulsions and micelles in which only a relatively small fraction of the initial number of species (droplets or micelles) become polymer particles. © 1994 John Wiley & Sons, Inc.     

On the evolution of the rate of polymerization,number and size distribution of particles in styrene emulsion polymerization above CMC

This work is an extension of a communication reported by two of the authors [Carro and Herrera‐Ordoñez, Macromol Rapid Commun 2006, 27, 274], where bimodal particle size distributions (PSD), obtained by asymmetric flow‐field flow fractionation (AFFF, AF⁴), were taken as evidence of certain degree of stability of primary particles. Now, emulsion polymerizations of styrene were performed under conditions employed before by other researchers, intending to examine if the behavior observed is general. The number of particles (N) and PSD were studied by means of dynamic light scattering and AF⁴. By the later, bimodal PSDs were detected in all cases, where the population corresponding to primary particles (diameter <20 nm) depends on reaction conditions. Regarding N, AF⁴ results show that it is constant during interval II, in contrast to DLS results. Primary particle coagulation was evidenced as minimums in N evolution and the rate of polymerization curves, monitored by calorimetry and gravimetry, which are enhanced when higher particle number is generated and/or the ionic strength is increased. These results suggest that particle coagulation is not as extensive as it would be expected according to the coagulative theory. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 3152–3160, 2010     

Unseeded semibatch emulsion polymerization of butyl acrylate: Bimodal particle size distribution

Unseeded semibatch emulsion polymerization of butyl acrylate (BA) using sodium lauryl sulfate as emulsifier and potassium persulfate as initiator was carried out at the conditions where secondary nucleation was probable. This was achieved by using no emulsifier in the initial reactor charge. The effects of changes in monomer emulsion feed rate, initiator concentration and distribution, emulsifier concentration in the feed, and temperature on the evolution of particle size averages and distribution were investigated. Bimodal particle size distributions (PSD) were obtained for most of the latexes. Inhibition effects were found to be important in the development of PSD. Primary particle formation occurred through micellar nucleation, whereas secondary nucleation probably occurred through homogenous nucleation. The polydispersity index (PDI) of the latexes increased with the decreasing monomer emulsion feed rate. The application of a larger amount of initiator to the reactor charge or using a higher temperature, reduced the formation of secondary particles and resulted in a formation of an unimodal PSD. The overall steady‐state rate of polymerization was found to approach the rate of monomer addition (R_p ≈ R_a ), if the emulsifier concentration in the aqueous phase was appreciable. This is different from the correlation 1/R_p = 1/K + 1/R_a obtained for the BA semibatch process with neat monomer feed. This suggests that different rate expressions can be used for BA semibatch emulsion polymerization at different conditions. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 528–545, 2000     

Miniemulsion polymerization of styrene using the oil-soluble initiator AMBN

The Mettler RC1 calorimeter was used to measure the rate of polymerization of conventional emulsion, homogenized emulsion, and miniemulsion polymerizations of styrene initiated with 2,2′-azobis(2-methylbutyronitrile). It was noted that the rate of polymerization significantly increased as the surface area of the monomer droplets increased. This was taken as strong evidence that in the miniemulsion and homogenized emulsion polymerizations, the fraction of the initiator soluble in the oil phase was responsible for single radical generation. The partitioning of AMBN at 70 °C was measured by high-pressure liquid chromatography to be 134 parts in the oil : 1 part in the water. Predissolving polystyrene in the miniemulsion prior to homogenization resulted in an enhancement in the rate of polymerization, although to a lesser extent than what has been previously noted for parallel miniemulsion polymerizations initiated with potassium persulfate. It was also noted that the method of addition of the oil-soluble initiator (either predissolved in the monomer prior to homogenization or dissolved in a small separate phase of monomer and added directly to the reactor) has a measurable effect on the kinetics in the miniemulsion polymerization of styrene. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 4449–4457, 1999     

Synthesis of large,high‐solid‐content latexes by miniemulsion polymerization

Multiple and diverse applications have been recently found for miniemulsions and miniemulsion polymerization. In this work, miniemulsion polymerization is presented as a suitable technique for the preparation of high‐solid‐content latices with large particle sizes. Monomer miniemulsions were prepared with a high‐pressure homogenizer, and droplet sizes of 200–700 nm were obtained. Latexes with particle sizes larger than the sizes commonly accepted for miniemulsion polymerization were obtained. With fixed operational conditions of the homogenizer, the type of stabilizer was the key parameter determining the droplet size and the droplet size distribution. The particle size of the latices obtained by miniemulsion polymerization indicated that the particles were mainly formed by droplet nucleation. Latexes obtained by this process have multiple applications, including use as seeds in the polymerization of high‐solid‐content latices. This article shows that potential new applications for miniemulsion polymerization are far from being exhausted. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 4222–4227, 2004     

Evolution of multimodal particle size distribution in vinyl acetate/butyl acrylate emulsion copolymerizations

This article presents a study on the engineering of multimodal distributions in semibatch emulsion polymerizations with nonionic surfactants. Various methods of producing multimodal distributions are demonstrated, and the sensitivity of the process to the properties of the reagents are analyzed. A test‐bed emulsion polymerization system, equipped with instrumentation to measure particle size distribution (capillary hydrodynamic fractionator) and monomer conversion (densitometer and flow meters), is used for this purpose. The process is monitored and controlled with an industrial distributed control system, which enables the automated operation of the process through sequential or logic controllers operating over lower level proportional integral derivative controllers. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 2232–2249, 2003     

Miniemulsion polymerization of styrene with a block copolymer surfactant

A series of miniemulsion systems based on styrene/azobisisobutyronitrile in the presence of poly(methyl methacrylate‐b‐2‐(dimethylamino)ethyl methacrylate) as a surfactant and hexadecane (HD) as a cosurfactant were developed. For comparison, a series of pseudoconventional emulsions also were carried out with the same procedure used for the aforementioned series but without the cosurfactant (HD). Both the droplet size and shelf life were also measured. Experimental results indicate that it is possible to slow the effect of Ostwald ripening and thereby produce a stable miniemulsion with the block copolymer as the surfactant and HD as the cosurfactant. In addition, the extent to which varying the surfactant concentration and copolymer composition could affect both the polymer particle size during the polymerization and the polymerization rate was examined. Variation in the polymer particle sizes during polymerization indicates that droplet and aqueous (micellar or both homogeneous) nucleation occurs in the miniemulsion polymerization. With the same concentration of the surfactant used in the miniemulsion polymerization, the polymerization rates of systems with M₁₂B₃₆ are faster than those of systems with M₁₂B₁₂. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 1818–1827, 2000     

Particle formation in interval III of the emulsion polymerization of styrene with aerosol‐MA as an emulsifier

Particle nucleation in the seeded emulsion polymerization of styrene in the presence of Aerosol‐MA emulsifier micelles and in the absence of monomer droplets (interval III) was investigated. The seed particles were swollen with different amounts of the styrene monomer before the experiments. A larger number of polymer particles formed in interval III than in the corresponding seeded batch operation in the presence of monomer droplets. The increase in the number of particles could be attributed to the reduced rate of growth of new particles, which retarded the depletion of emulsifier micelles. The number of secondary particles initially increased with the initial polymer weight ratio in the seed particles (w_p0) but decreased at a higher range of w_p0, after reaching a maximum at w_p0 = 0.60, and eventually was reduced to zero. At high values of w_p0 (>0.75), polymerization occurred in the seed particles, whereas few or no new particles were formed despite the presence of micelles. The cessation of particle formation at high conversions was ascertained with a semibatch process in which the neat monomer feed was added to the reaction vessel containing the seed particles and emulsifier micelles. For w_p0 > 0.85, the emulsifier micelles were disintegrated to stabilize the seed particles with no secondary particle formation. The possible reasons for the cessation of particle formation at high w_p0 were examined. The size distribution of secondary particles showed a positive skewness in terms of volume because of the declining rate of growth for particles, together with a low rate of growth for small particles. The distribution breadth of new particles sharpened with increasing w_p0. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 1652–1663, 2002     

Methyl methacrylate emulsion polymerization at low monomer concentration: Kinetic modeling of nucleation,particle size distribution,and rate of polymerization

The results of a mathematical model developed in the authors' previous work are discussed and compared against final number (N) and size distribution of particles (PSD) and the rate of polymerization (RP) experimental data of methyl methacrylate (MMA) emulsion polymerization above the critical micelle concentration (cmc) of the surfactant. On the basis of the model results, the hypothesis that the observed bimodal PSD can be ascribed to secondary nucleation as proposed in the literature is questionable. It is discussed that this PSD can also be caused by differences in the growing rate of different‐size particles as predicted for styrene emulsion polymerization. Because of the small particle size obtained at low initial monomer concentration, the high rate of free‐radical desorption reduces the accumulation of these species; therefore, the autoacceleration effect is less pronounced for the conditions under study compared with the usual behavior of the RP during MMA emulsion polymerization above cmc. Similarities and differences between model predictions and experimental data are discussed. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 39: 2547–2556, 2001     

Particle Nucleation and Growth in the Emulsion Polymerization of Styrene: Effect of Monomer/Water Ratio and Electrolyte Concentration

This work is an extension of previous research results reported by our team (Colloid and Polymer Science 2013, 291: 2385-2398), where large scale and high solid content latexes of poly(n-butyl acrylate) were obtained with the particle coagulation method induced by the electrolyte. However, how to prepare controlled particle size distribution polymer latex has not been studied. Thus, in this study, the effect of the monomer/water ratios and electrolyte concentrations on particle formation and growth methods were studied by following the tracks of the evolutions of particle size, number and distribution as a function of reaction time or conversion. Experimental results showed that the length of time that particle nucleation occurred increased with increasing monomer charged for the systems without electrolyte. A point worthy of attention here is that homogeneous nucleation may occur at high monomer concentrations (30/70, 40/60). However, electrolyte added could be made the nucleation mechanism shift from micellar/homogeneous nucleation to micelle /coagulation nucleation. As a result, the final particle size distribution can be controlled by adding an appropriate electrolyte to regulate the nucleation mechanism. Spherical and uniformly sized particles could be obtained when electrolyte concentration is between 0.2 wt% and 0.4 wt% for water at the high monomer/water ratio (40/60). The effects of electrolyte concentration on nucleation mechanism mainly were expressed by decreasing the solubility of the monomer and interparticle potential, and then preventing homogeneous nucleation and enhancing particle coagulation.     

Particle nucleation in high solids batch miniemulsion polymerization stabilized with a polymeric surfactant

The nucleation of polymer particles in the miniemulsion polymerization of vinyl acetate/VeoVa10 (VAc/VeoVa10) stabilized with PVOH was studied. The effect of costabilizer type, PVOH concentration, and type (thermal water‐soluble and oil‐soluble; and redox water‐soluble) and concentration of initiator on the extent of droplet nucleation were studied. Droplet nucleation was maximized by improving miniemulsion stability and using efficient initiators. These high solids dispersions could not be obtained by using a conventional batch emulsion polymerization. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 6407–6415, 2008     

On the Reaction Characteristics of Miniemulsion Polymerization with Aqueous Phase Initiation – Experiments and Modeling

Miniemulsions, consisting of submicron droplets of very hydrophobic lauryl methacrylate or 4‐tert‐butyl styrene, are successfully polymerized using water‐soluble sodium persulfate. Monitoring the calorimetric profile as well as the droplet and particle size distribution with conversion manifests a process of monomer redistribution, droplet disappearance, and narrowing of the particle size distribution. The observed reaction characteristics could be modeled adequately, using thermodynamic principles. The results of the work presented do not only have predicting value, but also enfeeble the idea of a one‐to‐one translation of monomer droplets into polymer particles in miniemulsion polymerization.     

Control of particle size in dispersion polymerization of methyl methacrylate

Poly(methyl methacrylate) (PMMA) particles ranging in diameter from 2 to 10 μm were prepared by dispersion polymerization. The effects of various polymerization parameters on the size and monodispersity were systematically investigated. The particle size was found to increase with increasing polymerization temperature, concentration and decomposition rate of the initiator, and solvency of the dispersion medium. It also increased with increasing concentration and molecular weight of the polymeric stabilizer, poly(vinyl pyrrolidone) (PVP). As the monomer concentration was increased from 5 to 20 wt %, a minimum was found in the particle size at a monomer concentration of 10 wt %. A costabilizer was found to be necessary for preparing monodisperse particles at stabilizer concentrations below 2 wt %. A recycling experiment showed that the consumption of PVP was quite small in each cycle and the residual materials in this system could be reused readily. © 1993 John Wiley & Sons, Inc.     

Miniemulsion polymerization of styrene with chain transfer agent as cosurfactant

Miniemulsion polymerization of styrene with the chain transfer agent n-dodecyl mercaptan (DDM) used as cosurfactant was studied. Droplet size and shelf life for unpolymerized miniemulsions were measured and compared with those of equivalent macroemulsions. The miniemulsion monomer droplets with dodecyl mercaptan as cosurfactant were very stable. Shelf lives were from 17 h to 3 months. The kinetics of miniemulsion polymerization were studied. Unlike other miniemulsion systems where the cosurfactant does not act as a chain transfer agent, the polymerization rate falls with cosurfactant level because the chain transfer agent enhances radical desorption from the particles. The polymerization rate in all the miniemulsions was lower than that of the corresponding macroemulsions. Polymerized particles were larger than in the corresponding macroemulsions, but molecular weights were lower. Results indicate that DDM can serve as an effective cosurfactant as well as a chain transfer agent. The fact that the molecular weights are lower in the miniemulsion reactions indicates predominant droplet nucleation. © 1997 John Wiley & Sons, Inc.     

Crosslinking network structure governing particle shape and size distribution by one-step emulsion polymerization in the presence of particle coagulation

In this study, sub-200?nm, crosslinked latex particles with a narrow particle size distribution were prepared by one-step emulsion polymerization in the presence of particle coagulation. The relationship between the particle shape and particle coagulation was investigated by varying the time of crosslinking network structure formation and particle coagulation. Particles with irregular shapes such as doublet, triplet, and ellipsoid were obtained using divinylbenzene (DVB) and ethylene glycol dimethacrylate (EGDMA) as the crosslinking agents, because the crosslinking network structure of particles was formed before the particle coagulation. In contrast, latex particles with a uniform spherical shape were also prepared using triallyl isocyanurate (TAIC) or dihydrodicyclopentadienyl acrylate (DCPA) as the crosslinking agents by delaying the time of crosslinking network structure formation. Alternatively, uniform spherical latex particles were prepared by bringing forward the particle coagulation time using cationic initiator, 2, 2′-azobis (2-methylpropionamidine) dihydrochloride (AAPH). This study presents a new idea that would further broaden the application of particle coagulation in emulsion polymerization.     

On the evolution of particle size average and size distribution in suspension polymerization processes

The dispersion of methyl methacrylate (MMA) and its suspension polymerization were used as models to elaborate the evolution of particle size average and size distribution in the course of suspension polymerization. The underlying mechanisms for the occurrence of the dynamic and static steady states in the population of drops were defined and their effects on the evolution of drop/particle size average and size distributions were examined. The characteristic intervals of suspension polymerizations (transition, steady-state, growth, and identification) were elaborated. The formation of satellite droplets and their evolution in the course of polymerization were also discussed.     

Effect of dose rate on emulsion and microemulsion polymerization of styrene

Emulsion and microemulsion polymerization of styrene were initiated with a gamma ray to study the effect of dose rate on polymerization. In both systems, there is an apparent plateau of polymerization rate in the curve of reaction rate vs. conversion. It was shown that emulsion polymerization conformed to the Smith–Ewart theory very well. Changing the dose rate in interval 2 had no great influence on polymerization rate, but it changed the average lifetime of radicals in polymer particles and affected the molecular weight of polymer produced. For microemulsion polymerization it was assumed that in the plateau it is the number of growing polymer particles being kept constant, not the number of polymer particles. When the dose rate was changed while the polymerization came into the constant period, the polymerization rate and the molecular weight of the polymer varied with the dose rate. © 1998 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 36: 257–262, 1998     

Heterogeneous polymerization with polyaspartate macromonomer having vinyl pendant groups. II. Control of particle diameter and diameter distribution in dispersion copolymerization

To control particle diameter and particle diameter distribution in dispersion copolymerization of styrene and sodium polyaspartate macromonomer containing vinylbenzyl pendant groups, effects of some polymerization parameters, water contents, initiator concentration, styrene monomer concentration, reaction temperature, and type of initiator on the particle diameter and the diameter distribution were investigated. Variation of the water contents from 20 to 80 vol % controls the resultant particle diameter from 0.066 to 0.47 μm. The diameter increased with increasing initiator concentration. This tendency is similar to dispersion polymerization system using a nonpolymerizable stabilizer. Particle diameter distribution broadened with increasing styrene monomer concentration. This trend was attributed to the increase of a period of particle formation. This result indicated that the period of particle formation affected the resultant particle diameter distribution. Particle diameter distribution was successfully improved (CV = 9.1 from 23.6%) by shortening of decomposition time of initiator. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 2281–2288, 2009     

On the miniemulsion polymerization of very hydrophobic monomers initiated by a completely water‐insoluble initiator: thermodynamics,kinetics, and mechanism

Successful miniemulsion polymerizations of very hydrophobic monomers, such as lauryl methacrylate and 4‐tert‐butyl styrene, initiated by very hydrophobic (i.e., completely water‐insoluble) lauroyl peroxide, are reported. Conversion‐time histories, as well as final latex properties, for example, the particle size distribution, are different from similar miniemulsion polymerizations in the presence of water‐soluble initiators. The observed differences can be attributed to the average number of radicals inside a miniemulsion particle; the system obeys Smith‐Ewart case I rather than Case II kinetics. Albeit the pairwise generation of radicals in the monomer droplets, substantial polymerization rates are observed. Water, present in the droplet interfacial layer, is supposed to act as chain transfer agent. The product of a chain transfer event is a hydroxyl radical, exit of this hydroxyl radical allows for the presence of single radicals in particles. The proposed mechanisms allow for agreement between initial droplet and final particle size distributions in miniemulsion polymerization initiated by lauroyl peroxide. © 2016 The Authors Journal of Polymer Science Part A: Polymer Chemistry Published by Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 2731–2745     

Modeling of the styrene microemulsion polymerization

A mathematical model was developed to simulate the polymerization kinetics of styrene oil-in-water microemulsions. Nucleation of particles in microemulsion droplets was assumed to account for the number of particles generated. It was found that the entry rate coefficient of radicals into microemulsion droplets is much smaller than the entry rate coefficient into monomer-swollen particles. All particles contain at most one growing radical. Various radical entry mechanisms were evaluated using the simulation. The possibility of flocculation between particles during the later stages of the polymerization and the high desorption rate of monomeric radicals was suggested by the simulation results. The likelihood of re-entry of desorbed radicals was den onstrated.