Surface characteristic of poly(p‐phenylene terephthalamide) fibers with oxygen plasma treatment

Oxygen plasma is widely employed for modification of polymer surfaces. Plasma treatment process is a convenient procedure that is also environmentally friendly. This study reports the effects of oxygen plasma treatment on the surface properties of poly(p‐phenylene terephthalamide) (PPTA) fibers. The surface characteristics before and after oxygen plasma treatment were analyzed by XPS, atomic force microscopy (AFM) and dynamic contact angle analysis (DCAA). It was found that oxygen plasma treatment introduced some new polar groups (O? C?O) on the fiber surface, increased the fiber surface roughness and changed the surface morphologies obviously by plasma etching and oxidative reactions. It is also shown that the fiber surface wettability was improved significantly by oxygen plasma treatment. Copyright © 2008 John Wiley & Sons, Ltd.     

Surface modification of polyester by oxygen‐ and nitrogen‐plasma treatment

In this paper, we present a study on the surface modification of polyethyleneterephthalate (PET) polymer by plasma treatment. The samples were treated by nitrogen and oxygen plasma for different time periods between 3 and 90 s. The plasma was created by a radio frequency (RF) generator. The gas pressure was fixed at 75 Pa and the discharge power was set to 200 W. The samples were treated in the glow region, where the electrons temperature was about 4 eV, the positive ions density was about 2 × 10¹⁵ m^?3, and the neutral atom density was about 4 × 10²¹ m^?3 for oxygen and 1 × 10²¹ m^?3 for nitrogen. The changes in surface morphology were observed by using atomic force microscopy (AFM). Surface wettability was determined by water contact angle measurements while the chemical composition of the surface was analyzed using XPS. The stability of functional groups on the polymer surface treated with plasma was monitored by XPS and wettability measurements in different time intervals. The oxygen‐plasma‐treated samples showed much more pronounced changes in the surface topography compared to those treated by nitrogen plasma. The contact angle of a water drop decreased from 75° for the untreated sample to 20° for oxygen and 25° for nitrogen‐plasma‐treated samples for 3 s. It kept decreasing with treatment time for both plasmas and reached about 10° for nitrogen plasma after 1 min of plasma treatment. For oxygen plasma, however, the contact angle kept decreasing even after a minute of plasma treatment and eventually fell below a few degrees. We found that the water contact angle increased linearly with the O/C ratio or N/C ratio in the case of oxygen or nitrogen plasma, respectively. Ageing effects of the plasma‐treated surface were more pronounced in the first 3 days; however, the surface hydrophilicity was rather stable later. Copyright © 2008 John Wiley & Sons, Ltd.     

A comparison of the strength of autohesion of plasma treated amorphous and semi‐crystalline PEEK films

Polyether ether ketone (PEEK) is a promising material for the encapsulation of electronic components for medical implants but a strong and hermetic joining technology is required. Autohesion is a self‐bonding method that avoids the need for adhesives. The strengths of autohesive joins using amorphous and semi‐crystalline PEEK films after surface activation using RF plasma were compared. Both types of PEEK films showed successful autohesion after activation with the bond strength of the amorphous sample being twice as high as the bond strength of the semi‐crystalline sample. Plasma treatment increased the autohesion strength of PEEK with no observed change in surface roughness (as measured by profilometer). The water contact angle was reduced by the treatment. X‐ray photoelectron spectroscopy (XPS) was carried out to determine surface chemistry. In the case of the semi‐crystalline surface, plasma treatment increased the relative percentage of C? O functional groups compared to the untreated surface. For treated surfaces nitrogen concentration correlated positively with bond strength while oxygen concentration correlated negatively with the semi‐crystalline PEEK samples and positively with the amorphous PEEK samples. The oxygen groups most likely are formed after the treatment by ambient oxidation are not conducive to bond formation, possibly because of the quenching of radicals that would otherwise form links. Copyright © 2010 John Wiley & Sons, Ltd.     

Surface Modifications Produced by N2 and O2 RF Plasma Treatment on a Synthetic Vulcanized Styrene-Butadiene Rubber

A low-pressure gas RF plasma-treatment has been used to improve the adhesion of a synthetic vulcanized rubber to polyurethane adhesive as an environmentally friendly alternative surface treatment to the conventional chemical treatments. A sulfur vulcanized styrene-butadiene rubber (R2) containing a noticeable amount of zinc stearate and paraffin wax (both providing a lack of adhesion) in its formulation was used. Two different gases (oxygen and nitrogen) were used to generate the RF plasma, which was performed at 50 Watt for 1–15 min. The modifications produced on the R2 rubber surface by the RF plasma treatments were assessed by using advancing and receding contact angle measurements, ATR-IR spectroscopy, X-ray Photoelectron Spectroscopy (XPS), Scanning Force Microscopy (SFM), and Scanning Electron Microscopy (SEM). Adhesion evaluation was obtained from T-peel tests of joints produced between plasma treated R2 rubber and a polyurethane adhesive. The plasma treatment produced a decrease in advancing and receding contact angle values on R2 rubber, irrespective to the gas used to generate the RF plasma. The treatment with RF plasma produced the partial removal of hydrocarbon moieties from the rubber surface and the generation of oxygen moieties. An increase in surface roughness was also produced. The degree of oxidation and the amount of hydrocarbon-rich layer removed from the R2 rubber surface was more important by treating with oxygen plasma. The treatment of rubber in oxygen plasma for 1 minute was enough to noticeably increase adhesion of R2 rubber to polyurethane adhesive. However, an extended treatment (15 min.) was needed when nitrogen plasma was applied to R2 rubber. The loci of failure in the joints produced between the plasma treated R2 rubber and the polyurethane adhesive was assessed by using ATR-IR spectroscopy. A mixed failure (partially adhesional and partially cohesive failure in the rubber) in the joints produced with plasma treated R2 rubber joints was always obtained.     

A Comparison of PE Surfaces Modified by Plasma Generated Neutral Nitrogen Species and Nitrogen Ions

The surface modification of polyethylene (PE) by neutral nitrogen species (ground and excited state N₂ as well as atomic N; modified nitrogen plasma treatment) has been compared to the effect of nitrogen ion bombardment using X-ray Photoelectron Spectroscopy (XPS) and contact angle measurements. XPS results indicate that a greater nitrogen concentration was grafted during the modified nitrogen plasma treatment of PE, an effect that was attributed to surface sputtering during ion beam modification. The distribution of nitrogen-containing functionalities was strongly dependent upon the treatment strategy; the modified nitrogen plasma treatment lead predominantly to imine groups being formed at the PE surface, while amine groups were the dominant species produced during ion beam modification. The presence of electron irradiation during the modified nitrogen plasma treatment of PE did not modify the rate of nitrogen incorporation or change the nature of N-containing functional groups produced but did lead to a systematic decrease in contact angle.     

Surface modification of plasma‐pretreated expanded poly (tetrafluroethylene) films by graft copolymerization

A two‐step process based on a low‐pressure helium plasma treatment followed by acrylic acid‐grafting copolymerization was used for the surface modification of expanded polytetrafluoroethylene (ePTFE) films. The effects of plasma treatment power and treatment time on the hydrophilicity of the film surface were investigated. The wettability of the ePTFE film surface was characterized by water contact angle, and the surface compositions of the untreated and treated ePTFE samples were evaluated by atomic force microscopy and XPS. Contact angle measurements revealed that the hydrophilicity of the ePTFE film surface was greatly enhanced by the combined actions of the plasma treatment and acrylic acid grafting, and the contact angle decreased from 145° to 66°. Atomic force microscopy analyses showed that the surface roughness increased after the plasma treatment. XPS analyses showed substantial increase in the concentration of carbon and oxygen atoms and a decrease in the concentration of fluorine atoms at the film surface. T‐peel strength showed an improved bonding strength between the film and an adhesive tape after the treatment. Copyright © 2012 John Wiley & Sons, Ltd.     

等离子体改性聚氯乙烯的TiO2光催化降解研究

聚氯乙烯(PVC)是一种通用型塑料,无论采用挤出、注射或浸渍等方法均有优异的成型性能,至今仍是大量使用的弹性体.……     

辉光放电处理聚四氟乙烯：Ⅲ.PTFE表面结构的XPS表征

Yasuda等在用XPS研究离子体处理后的PTFE表面结构时,得到一个包络的C_(1s)峰。本文对此进行探讨。 PTFE膜先在蒸馏水中浸泡1小时,再用热异丙醇洗涤5分钟,然后用去离子水清洗三     

Intriguing roles of reactive intermediates in dissociation chemistry of N-phenylcinnamides

In mass spectrometry of protonated N-phenylcinnamides, the carbonyl oxygen is the thermodynamically most favorable protonation site and the added proton is initially localized on it. Upon collisional activation, the proton transfers from the carbonyl oxygen to the dissociative protonation site at the amide nitrogen atom or the α-carbon atom, leading to the formation of important reactive intermediates. When the amide nitrogen atom is protonated, the amide bond is facile to rupture to form ion/neutral complex 1, [RC(6)H(4)CH[double bond, length as m-dash]CHCO(+)/aniline]. Besides the dissociation of the complex, proton transfer reaction from the α-carbon atom to the nitrogen atom within the complex takes place, leading to the formation of protonated aniline. The presence of electron-withdrawing groups favored the proton transfer reaction, whereas electron-donating groups strongly favored the dissociation (aniline loss). When the proton transfers from the carbonyl oxygen to the α-carbon atom, the cleavage of the C(α)-CONHPh bond results in another ion/neutral complex 2, [PhNHCO(+)/RC(6)H(4)CH[double bond, length as m-dash]CH(2)]. However, in this case, electron-donating groups expedited the proton transfer reaction from the charged to the neutral partner to eliminate phenyl isocyanate. Besides the cleavage of the C(α)-CONHPh bond, intramolecular nucleophilic substitution (a nucleophilic attack of the nitrogen atom at the β-carbon) and stepwise proton transfer reactions (two 1,2-H shifts) also take place when the α-carbon atom is protonated, resulting in the loss of ketene and RC(6)H(5), respectively. In addition, the H/D exchanges between the external deuterium and the amide hydrogen, vinyl hydrogens and the hydrogens of the phenyl rings were discovered by D-labeling experiments. Density functional theory-based (DFT) calculations were performed to shed light on the mechanisms for these reactions.     

聚乙酰亚胺涂敷单晶硅表面上全氟亏酸单层膜

Ultra-thin film of perfluorodecanoic acid expected to be excellent lubricant for micro-machines was prepared successfully on single crystal silicon substrate.The film was characterized by means of X-ray photoelectron spectroscopy (XPS) and contact-angle meter.The chemical reaction involved in the preparation of the ultra-thin film was discussed as well.After being immersed in a dilute aqueous solution of polyethyleneimine (PEI) for 15 minutes and rinsed with distilled water,the silicon substrate was coated with a thin film of PEI,which was then put into a dilute solution (1× 10－ 3 mol· L－ 1) of perfluorodecanoic acid in hexadecane.Subsequently the steady perfluorodecanoic acid ultra-thin film was developed on PEI coating in the presence of a covalent amide bond between carboxylic group and the primary or secondary amine groups of PEI.This process was accompanied by the contact angle changes of water droplet on the Si surface (see Table 1).Moreover,the reaction between perfluorodecanoic acid and PEI was significantly influenced by N,N′ -dicyclohexylcarbodiimide (DCCD).The contact angle on the ultra-thin film of perfluorodecanoic acid is only 66.3° in the absence of DCCD in the reacting solution; it rises to 89.4° in the presence of DCCD.This indicates that the reaction between perfluorodecanoic acid and PEI was accelerated by DCCD,and the quality of perfluorodecanoic acid ultra-thin film thus improved.XPS analysis of the ultra-thin film indicates that the derivatization of PEI with perfluorodecanoic acid was accompanied by several changes.First,a large and highly symmetrical F 1s peak appeared at 688.3 eV (C－ F*).Secondly,a new peak of N 1s appeared at 400.7 eV (chemical shift 1.4 eV),which was attributed to the N atom attached to the carbonyl group (O=C－ N*).Thirdly,three new peaks of C 1s appeared at 286.1 eV (chemical shift 1.5 eV),288.1 eV (chemical shift 3.5 eV),and 291.0 eV (chemical shift 5.4 eV),respectively.These C 1s peaks were attributed to the C atom attached to the O=C－ N group (O=C－ N－ C*),the carboxyl C atom (O=C*－ N),and the C atom in － CF3 group (C*－ F),respectively.Therefore it can be concluded that perfluorodecanoic acid has been chemically adsorbed onto the surface of PEI and perfluorodecanoic acid ultra-thin film prepared successfully.     

Manipulating the surface properties of polyacrylamide with nitrogen plasma

Polyacrylamide (PAL) was physically adsorbed onto a hydroxylated silicon surface to form a uniform PAL film and the up-top PAL thin film was treated by nitrogen (N₂) plasma for surface modification. The atomic composition of the modified surface of the PAL film adsorbed on silicon substrate was analyzed with Fourier Transform Infrared Spectroscopy (FTIR) and X-ray photoelectron spectroscopy (XPS). The surface energy of PAL film was calculated from the data of contact angle of three-probe liquid. The FTIR results show an increase of peak intensity at 1214 cm⁻¹ (NH₂ stretch vibration) after the nitrogen plasma treatment, which confirms that the nitrogen was grafted to the PAL surface in the process of N₂-plasma treatment. The XPS results show that the ratio of relative intensity of N1s to O1s increases with increasing the plasma treatment time, which further affirms the formation of the amine groups on the PAL surface after the nitrogen plasma treatment. The surface tension increases with increasing the plasma grafting time. However, the surface energy decreases rapidly at the early stage when stored in air and approaches to an equilibrium value. It suggests that some physically-adsorbed ions and alkyl radicals on PAL surface can rapidly lose their activities. The increase of the surface tension of the plasma treated PLA films is due to the amine groups covalently grafted to PAL surface.     

Surface modification of EPDM rubber by plasma treatment

The effect of argon, oxygen, and nitrogen plasma treatment of solvent cast EPDM rubber films has been investigated by means of atomic force microscopy (AFM), X-ray photoelectron spectroscopy (XPS), and surface energy measurements. Plasma treatment leads to changes in the surface energy from 25 to 70 mN/m. Treatment conditions influenced both the changes in surface energy and the stability, and it became more difficult to obtain good contact angle measurements after longer (> ca. 4 min) treatment times, probably because of an increasingly uneven surface structure. XPS analyses revealed that up to 20 at. % oxygen can be easily incorporated and that variations of approximately 5% can be controlled by the plasma conditions. Oxygen was mainly found in hydroxyl groups, but also as carbonyl and carboxyl. XPS analyses showed more stable surfaces than expected from contact angles, probably because XPS analysis is less surface sensitive than contact angle measurements. AFM measurements revealed different surface structures with the three gases. The surface roughness increased generally with treatment time, and dramatic changes could be observed at longer times. At short times, surface energy changes were much faster than the changes in surface structure, showing that plasma treatment conditions can be utilized to tailor both surface energies and surface structure of EPDM rubber.     

Wettability interpretation of oxygen plasma modified poly(methyl methacrylate)

Poly(methyl methacrylate) (PMMA) has been modified via a dc pulsed oxygen plasma for different treatment times. The modified surfaces were characterized by X-ray photoelectron spectroscopy (XPS), optical profilometer, zeta potential, and advancing contact angle measurements. The measured advancing contact angles of water decreased considerably as a function of discharge. Several oxygen-based functionalities (carbonyl, carboxyl, carbonate, etc.) were detected by XPS, while zeta potential measurements confirmed an increase in negative charge for the treated PMMA surface. Evaluating the correlation between the concentration of polar chemical species and zeta potential, we found that increase in surface hydrophilicity results from the coeffect due to incorporation of oxygen functional groups and creation of charge states. The electrical double layer (EDL) effect was also considered in contact angle interpretation by introducing an additional surface tension term into Young's equation. We also found that EDL contribution to the solid-liquid interfacial tension is negligible and can be safely ignored for the systems considered here.     

Influence of Plasma Treatment on the Electroless Deposition of Copper on Carbon Fibers

Air and nitrogen glow discharge were used to replace chromic acid pretreatment to deposit copper film on carbon fiber surfaces from an CuSO₄‐HCHO electroless system. A greater copper uptake and a more uniformly coated copper film were obtained for plasma‐treated carbon fibers. The adhesion between the copper film and the carbon fibers was also improved. An orthogonal table L₉(3⁴) was used to study the effects of discharge pressure, discharge power, time and gas type on the copper uptake. Scanning electron microscopy (SEM), reflection absorption infrared spectroscopy (RAIR) and X‐ray photoelectron spectroscopy (XPS) at different depths were applied to characterize the physical and chemical changes of the surface of the carbon fibers. The results showed that after plasma treatment, the carbon fiber surface became rough and several types of polar oxygen groups, such as carboxylic acid COOH, esters COOC, quinones Ph?O, etc., were introduced into the carbon fiber surface. A mechanism of plasma treatment effects on copper electroless deposition on the carbon fiber surface is also suggested.     

Plasma surface functionalization of poly[bis(2,2,2-trifluoroethoxy)phosphazene] films and nanofibers

Polyphosphazenes are a class of hybrid organic-inorganic macromolecules with high thermo-oxidative stability and good solubility in many solvents. Fluoroalkoxy phosphazene polymers also have high surface hydrophobicity. A method is described to tune this surface property while maintaining the advantageous bulk materials characteristics. The polyphosphazene single-substituent polymer, poly[bis(2,2,2-trifluoroethoxy)phosphazene], with flat film, fiber mat, or bead mat morphology was surface functionalized using an atmospheric plasma treatment with oxygen, nitrogen, methane, or tetrafluoromethane/hydrogen gases. Surface chemistry changes were detected by static water contact angle (WCA) measurements as well as X-ray photon spectroscopy (XPS). It was found that changes in the WCA of as much as 150 degrees occurred, accompanied by shifts in the ratio of elements on the polymer surface as detected by XPS. Overall this plasma technique provides a convenient method for the generation of specific surface characteristics while maintaining the hydrophobicity of the bulk material.     

聚甲基戊烯膜式氧合器表面碳酸酐酶的固定化及性能研究

聚甲基戊烯(PMP)膜式氧合器表面先用水等离子体改性,以引入羟基官能团;再以溴化氰为偶联剂,将碳酸酐酶(CA)偶联至其表面.改性后用X射线光电子能谱(XPS)、表面接触角及酶活性测定等方法研究PMP表面性能变化.结果表明,等离子体处理后,在PMP表面引入了大量的含氧官能团,与水的表面接触角从103.37°降低至50.01°.再将CA引入PMP表面后,与水的表面接触角进一步降低至39.23°;XPS的C1谱图中出现蛋白质的特征峰;以对硝基苯酚乙酸酯为底物,测得表面接枝CA的活性达到理论单分子层接枝活性的73%.改性后PMP表面物理化学性质的变化证明本文方法确实能成功地将羟基官能团、CA引入其表面.本方法有望应用在膜式氧合器上以提高其清除血液中CO2的能力.     

The interaction of hydrogen and ammonia plasmas with polymethacrylic esters,studied by static secondary ions mass spectrometry

The interactions of H₂ and NH₃ plasmas with the surfaces of various poly(alkylmethacrylate)s and of poly(phenylmethacrylate) have been studied with XPS and SSIMS. Experiments on poly(methylmethacrylate) reveal that during short treatment times with the NH₃ plasma chain, scission takes place and nitrogen is not incorporated into the surface. The chain scission also takes place with the H₂ plasma. With the aid of SSIMS results, the nature of the chain scission could be deduced. Comparison of these results with those on poly(n-butylmethacrylate) and poly(t-butylmethacrylate) reveals a reaction mechanism in which hydrogen atoms generated in both plasmas play an important role in the chain scission process. After longer treatment time with the NH₃ plasma, the poly(methylmethacrylate) surface becomes deoxygenated and nitrogen is incorporated into surface structures of low molecular weight. Experiments on poly(phenylmethacrylate) reveal that already during short treatment times with the NH₃ plasma, nitrogen is incorporated into the aromatic ring. Chain scission does not play an important role. One of the processes with the H₂ plasma is hydrogenation of the aromatic ring, leading to poly(cyclohexylmethacrylate).     

Deposition of polysiloxane‐like nanofilms onto an aluminium alloy by plasma polymerized hexamethyldisiloxane: characterization by XPS and contact angle measurements

In this work, aluminium (Alclad 2024‐T3) substrates were cleaned by an r.f. (13.56 MHz) plasma, using argon (Ar), oxygen (O₂) and a mixture of O₂/Ar (50:50) gases. The effectiveness of plasma cleaning was checked in situ using X‐ray photoelectron spectroscopy (XPS) and ex situ using water contact angle measurements. XPS O/Al surface atomic ratios are in excellent agreement with those of the crystalline boehmite and the pseudoboehmite. Oxygen O 1s peak‐fitting was used to quantify the proportion of hydroxyl ions and the functional composition on the aluminium surface: the surface cleaned with O₂ plasma contains 50% of aluminium hydroxides, the ones cleaned with Ar plasma and with Ar/O₂ plasma contain, respectively, 25 and 37% hydroxyl ions. The binding energy separation between Al 2p and O 1s is characteristic of AlO(OH). Thin SiO_x films were subsequently deposited from a mixture of hexamethyldisiloxane (HMDSO) and oxygen. In the absence of oxygen, a hydrophobic (Θ≥ 100° ) film characteristic of polydimethylsiloxane (PDMS) is formed: polysiloxane‐like thinner films (SiO_x) are obtained with the introduction of oxygen. XPS and contact angle measurements confirmed both the composition and the structure of these films. More importantly, contact angle measurements using different liquids and interpreted with the van Oss‐Good‐Chaudhury theory allowed determination of the surface free energy of the deposited films: the calculated values of surface tension of the film formed from HMDSO/O₂: (50/50) are in excellent agreement with those of reference silica‐based materials such as a silicon wafer and cleaned glass. Copyright © 2007 John Wiley & Sons, Ltd.     

Surface modification of high-performance polymeric fibers by an oxygen plasma. A comparative study of poly(p-phenylene terephthalamide) and poly(p-phenylene benzobisoxazole)

Poly(p-phenylene terephthalamide) (PPTA) and poly(p-phenylene benzobisoxazole) (PBO) fibers were exposed to an oxygen plasma under equivalent conditions. The resulting changes in the surface properties of PPTA and PBO were comparatively investigated using inverse gas chromatography (IGC) and atomic force microscopy (AFM). Both non-polar (n-alkanes) and polar probes of different acid-base characteristics were used in IGC adsorption experiments. Following plasma exposure, size-exclusion phenomena, probably associated to the formation of pores (nanoroughness), were detected with the largest n-alkanes (C(9) and C(10)). From the adsorption of polar probes, an increase in the number or strength of the acidic and basic sites present at the fiber surfaces following plasma treatment was detected. The effects of the oxygen plasma treatments were similar for PPTA and PBO. In both cases, oxygen plasma introduces polar groups onto the surfaces, involving an increase in the degree of surface nanoroughness. AFM measurements evidenced substantial changes in the surface morphology at the nanometer scale, especially after plasma exposure for a long time. For the PBO fibers, the outermost layer - contaminant substances - was removed thanks to the plasma treatment, which indicates that this agent had a surface cleaning effect.     

Long-lasting hydrophilicity on nanostructured Si-incorporated diamond-like carbon films

We investigated the long-lasting hydrophilic behavior of a Si-incorporated diamond-like carbon (Si-DLC) film by varying the Si fraction in DLC matrix through oxygen and nitrogen plasma surface treatments. The wetting behavior of the water droplets on the pure DLC and Si-DLC with the nitrogen or oxygen plasma treatment revealed that the Si element in the oxygen-plasma-treated Si-DLC films played a major role in maintaining a hydrophilic wetting angle of <10° for 20 days in ambient air. The nanostructured patterns with a roughness of ～10 nm evolved because of the selective etching of the carbon matrix by the oxygen plasma in the Si-DLC film, where the chemical component of the Si-Ox bond was enriched on the top of the nanopatterns and remained for over 20 days.