The control of turbulent end-wall boundary layers using surface suction

An experimental evaluation of the effects of spatially-limited (i.e. localized) surface suction on a turbulent junction flow was performed using Particle Image Velocimetry (PIV). The results indicate that surface suction can (1) weaken both the instantaneous turbulent vortex and its associated surface interactions in the symmetry plane, (2) effectively eliminate the presence of the average turbulent necklace vortex in the symmetry plane, and (3) weaken the average downstream extensions of the vortex. It was also established that suction effectively reduces the low frequency component of the Reynolds-stress in both the symmetry plane and trailing-edge cross-stream planes, and stabilizes the behavior of the trailing vortex legs. Received: 18 May 1998/Accepted: 26 March 1999     

Laser-Doppler measurements of laminar and turbulent flow in a pipe bend

Laser-Doppler measurements are reported for laminar and turbulent flow through a 90° bend of circular cross-section with mean radius of curvature equal to 2.8 times the diameter. The measurements were made in cross-stream planes 0.58 diameters upstream of the bend inlet plane, in 30, 60 and 75° planes in the bend and in planes one and six diameters downstream of the exit plane. Three sets of data were obtained: for laminar flow at Reynolds numbers of 500 and 1093 and for turbulent flow at the maximum obtainable Reynolds number of 43 000. The results show the development of strong pressure-driven secondary flows in the form of a pair of counter-rotating vortices in the streamwise direction. The strength and character of the secondary flows were found to depend on the thickness and nature of the inlet boundary layers, inlet conditions which could not be varied independently of Reynolds number. The quantitative anemometer measurements are supported by flow visualization studies. Refractive index matching at the fluid-wall interface was not used; the measurements consist, therefore, of streamwise components of mean and fluctuating velocities only, supplemented by wall pressure measurements for the turbulent flow. The displacement of the laser measurement volume due to refraction is allowed for in simple geometrical calculations. The results are intenden for use as benchmark data for calibrating flow calculation methods.     

Mechanism of compressor airfoil boundary layer flow control using nanosecond plasma actuation

The flow control effects of nanosecond plasma actuation on the boundary layer flow of a typical compressor controlled diffusion airfoil are investigated using large eddy simulation method. Three types of plasma actuation are designed to control the boundary layer flow, and two mechanisms of compressor airfoil boundary layer flow control using nanosecond plasma actuation have been found. The plasma actuations located within the laminar boundary layer flow can induce a small vortex structure through influencing on the density and pressure of the flow field. As the small vortex structure moves downstream along the blade surface with the main flow, it can suppress the turbulent flow mixing and reduce the total pressure loss. The flow control effect of the small vortex structure is summarized as wall jet effect. Differently, the plasma actuation located within the turbulent boundary layer flow can act on the shear layer flow and induce a large vortex structure. While moving downstream, this large vortex structure can suppress the turbulent flow mixing too.     

Investigation of the flow in a circular cavity using stereo and tomographic particle image velocimetry

The turbulent flow over a circular cavity with an aspect ratio of D/H = 2 is investigated by multi-planar stereoscopic particle image velocimetry and with tomographic particle image velocimetry (PIV). The main aim of the study is the flow topology and the turbulent structure of the asymmetrical flow pattern that forms inside the cavity at these specific conditions. The flow field is measured in the vertical symmetry plane to describe the overall recirculation pattern in the cavity and the turbulent shear layer developing from the separation point. In this specific regime the shear layer fluctuations are recognized as those caused by instabilities together with the effect of the incoming boundary layer turbulence. Additional observations performed at several wall-parallel planes at different height inside the cavity allow to further evaluate the secondary flow circulation generated by this asymmetric regime. The observed flow pattern consists of a steady vortex, occupying the entire cavity volume and placed diagonally inside the cavity such to entrain the external flow from one side, capture it into a circulatory motion and eject it from the opposite side of the cavity. The spatial distribution of the turbulent fluctuations also reveals the same structure. The tomographic PIV measurement returns a visual inspection to the instantaneous three-dimensional structure of the turbulent fluctuations, which at the investigated height exhibit a low level of coherence with slightly elongated vortices in the recirculating flow inside the cavity.     

Loss Production Mechanisms in a Laminar Separation Bubble

The present paper reports the results of a detailed experimental study, carried out by means of a two-component Laser Doppler Velocimeter, aimed at investigating the loss generation mechanisms induced by laminar separation bubble and transition process. Measurements have been performed along a flat plate installed within a double contoured test section, designed to produce an adverse pressure gradient typical of Ultra-High-Lift turbine blade profiles, which induces the formation of a laminar separation bubble. Results were detailed enough to allow calculating laminar and turbulent deformation works in the separated flow region. Normal and shear contributions of both viscous and turbulent deformation works have been analyzed and employed to explain the generation of total pressure losses in the separated flow region, where the generation and amplification of Kelvin–Helmholtz instability induces the separated shear layer roll-up, thus the bubble reattachment. Results obtained for different Reynolds number conditions have been employed for the formulation of a loss scaling procedure involving the separated shear layer thickness, which is directly correlated to the dynamics of Kelvin–Helmholtz roll-up vortices.     

Experimental investigation of the unsteady structure of a transitional plane wall jet

 A laminar wall jet undergoing transition is investigated using the particle image velocimetry (PIV) technique. The plane wall jet is issued from a rectangular channel, with the jet-exit velocity profile being parabolic. The Reynolds number, based on the exit mean velocity and the channel width, is 1450. To aid the understanding of the global flow features, laser-sheet/smoke flow visualizations are performed along streamwise, spanwise, and cross-stream directions. Surface pressure measurements are made to correlate the instantaneous vorticity distribution with the surface pressure fluctuations. The instantaneous velocity and vorticity field measurements provide the basis for understanding the formation of the inner-region vortex and the subsequent interactions between the outer-region (free-shear-layer region) and inner-region (boundary-layer region) vortical structures. Results show that under the influence of the free-shear-layer vortex, the local boundary layer becomes detached from the surface and inviscidly unstable, and a vortex is formed in the inner region. Once this vortex has formed, the free-shear-layer vortex and the inner-region vortex form a vortex couple and convect downstream. The mutual interactions between these inner- and outer-region vortical structures dominate the transition process. Farther downstream, the emergence of the three-dimensional structure in the free shear layer initiates complete breakdown of the flow. Received: 8 November 1995/Accepted: 6 November 1996     

Cross-Stream Vorticity Field Induced by Streamwise Vortices in Unbounded and Wall-Bounded Shear Flows

This computational study examines the unsteady cross-stream vorticity structures that form when one or more streamwise vortices are immersed in homogeneous and boundary-layer shear flows. A quasi-two-dimensional limit is considered in which the velocity and vorticity fields, while still possessing three nonzero components, have vanishing gradient in the streamwise direction. This idealization is suitable to applications such as streamwise vortices that occur along a ship hull or airplane fuselage and it can be used as an idealized representation of the quasi-streamwise vortices in the near-wall region of a turbulent boundary layer. In this quasi-two-dimensional idealization, the streamwise velocity has no effect on the cross-stream velocity associated with the vortex. However, the vortex acts to modify the cross-stream vorticity component, resulting in regions of the flow with strong deviations in streamwise velocity. This paper examines the complex structures that form as the cross-stream vorticity field is wrapped up by the vortex and the effect of these structures on the streamwise velocity field, first for vortices immersed in homogeneous shear flow and then for vortices immersed in a boundary layer along a flat wall. Received 2 January 2002 and accepted 13 August 2002 Published online 3 December 2002 RID="*" ID="*" This project was supported by the Office of Naval Research under Grant Number N00014-01-1-0015. Dr. Thomas Swain is the program manager. Communicated by T.B. Gatski     

An orthogonal-plane PIV technique for the investigations of three-dimensional vortical structures in a turbulent boundary layer flow

An experimental investigation was carried out regarding a three-dimensional topology of a zero-pressure gradient turbulent boundary layer. In this study, the polarization separation technique has been applied to the PIV measurements. Two mutually perpendicular measurement planes have been employed in x–y and x–z planes, respectively. Synchronization between a stereoscopic PIV with another plane PIV system was made toward the detection of such salient features of the coherent structure as the legs and the head of the hairpin vortices. Polarization rotation via a half-waveplate and subsequent particle image separation using polarizer minimized the spurious particle images. The PIV results clearly demonstrate the presence of hairpin-like coherent vortical structures and coincidence between the near-wall quasi-streamwise vortex pair and the legs of the hairpin vortex.     

Numerical prediction of turbulent boundary layer noise from a sharp-edged flat plate

An efficient hybrid uncorrelated wall plane waves–boundary element method (UWPW-BEM) technique is proposed to predict the flow-induced noise from a structure in low Mach number turbulent flow. Reynolds-averaged Navier-Stokes equations are used to estimate the turbulent boundary layer parameters such as convective velocity, boundary layer thickness, and wall shear stress over the surface of the structure. The spectrum of the wall pressure fluctuations is evaluated from the turbulent boundary layer parameters and by using semi-empirical models from literature. The wall pressure field underneath the turbulent boundary layer is synthesized by realizations of uncorrelated wall plane waves (UWPW). An acoustic BEM solver is then employed to compute the acoustic pressure scattered by the structure from the synthesized wall pressure field. Finally, the acoustic response of the structure in turbulent flow is obtained as an ensemble average of the acoustic pressures due to all realizations of uncorrelated plane waves. To demonstrate the hybrid UWPW-BEM approach, the self-noise generated by a flat plate in turbulent flow with Reynolds number based on chord Re_c = 4.9 × 10⁵ is predicted. The results are compared with those obtained from a large eddy simulation (LES)-BEM technique as well as with experimental data from literature.     

Optimally growing boundary layer disturbances in a convergent nozzle preceded by a circular pipe

We report the findings from a theoretical analysis of optimally growing disturbances in an initially turbulent boundary layer. The motivation behind this study originates from the desire to generate organized structures in an initially turbulent boundary layer via excitation by disturbances that are tailored to be preferentially amplified. Such optimally growing disturbances are of interest for implementation in an active flow control strategy that is investigated for effective jet noise control. Details of the optimal perturbation theory implemented in this study are discussed. The relevant stability equations are derived using both the standard decomposition and the triple decomposition. The chosen test case geometry contains a convergent nozzle, which generates a Mach 0.9 round jet, preceded by a circular pipe. Optimally growing disturbances are introduced at various stations within the circular pipe section to facilitate disturbance energy amplification upstream of the favorable pressure gradient zone within the convergent nozzle, which has a stabilizing effect on disturbance growth. Effects of temporal frequency, disturbance input and output plane locations as well as separation distance between output and input planes are investigated. The results indicate that optimally growing disturbances appear in the form of longitudinal counter-rotating vortex pairs, whose size can be on the order of several times the input plane mean boundary layer thickness. The azimuthal wavenumber, which represents the number of counter-rotating vortex pairs, is found to generally decrease with increasing separation distance. Compared to the standard decomposition, the triple decomposition analysis generally predicts relatively lower azimuthal wavenumbers and significantly reduced energy amplification ratios for the optimal disturbances.     

壁面湍流发卡涡包空间模态的TRPIV实验研究

运用高时间分辨率粒子图像测速(Time-resolved PIV简称TRPIV),测量得到平板湍流边界层流向/法向平面内瞬时速度矢量空间分布的时间序列;采用空间局部平均速度结构函数的概念,识别和提取湍流边界层中大尺度发卡涡包结构的空间特征。发现在湍流边界层中不同法向位置多个正负发卡涡包结构同时交替存在。这些分布在不同法向高度的发卡涡包结构之间通过倾斜的涡量剪切层相联系,构成了湍流边界层中内、外区紧密相连、相互作用的一种稳态的分布方式。     

A bypass wake induced laminar/turbulent transition

The process of laminar to turbulent transition induced by a von Karman vortex street wake, was studied for the case of a flat plate boundary layer. The boundary layer developed under zero pressure gradient conditions. The vortex street was generated by a cylinder positioned in the free stream. An X-type hot-wire probe located in the boundary layer, measured the streamwise and normal to the wall velocity components. The measurements covered two areas; the region of transition onset and development and the region where the wake and the boundary layer merged producing a turbulent flow. The evolution of Reynolds stresses and rms-values of velocity fluctuations along the transition region are presented and discussed. From the profiles of the Reynolds stress and the mean velocity profile, a ‘negative' energy production region along the transition region, was identified. A quadrant splitting analysis was applied to the instantaneous Reynolds stress signals. The contributions of the elementary coherent structures to the total Reynolds stress were evaluated, for several x-positions of the near wall region. Distinct regions in the streamwise and normal to the wall directions were identified during the transition.     

A hybrid numerical approach to predict the vibrational responses of panels excited by a turbulent boundary layer

In this work, a hybrid numerical approach to predict the vibrational responses of planar structures excited by a turbulent boundary layer is presented. The approach combines an uncorrelated wall plane wave technique with the finite element method. The wall pressure field induced by a turbulent boundary layer is obtained as a set of uncorrelated wall pressure plane waves. The amplitude of these plane waves are determined from the cross spectrum density function of the wall pressure field given either by empirical models from literature or from experimental data. The response of the planar structure subject to a turbulent boundary layer excitation is then obtained from an ensemble average of the different realizations. The numerical technique is computationally efficient as it rapidly converges using a small number of realizations. To demonstrate the method, the vibrational responses of two panels with simply supported or clamped boundary conditions and excited by a turbulent flow are considered. In the case study comprising a plate with simply supported boundary conditions, an analytical solution is employed for verification of the method. For both cases studies, numerical results from the hybrid approach are compared with experimental data measured in two different anechoic wind tunnels.     

Surface pressure on a cubic building exerted by conical vortices

Experiments were performed to study surface pressure on a cubic building underlying conical vortices, which are known to cause severe structural damage and failure. The focus is on the effects of turbulence in the incident flow. Three turbulent boundary layers were created in a boundary layer wind tunnel. A wall-mounted cube, i.e. a cube situated on the horizontal ground floor surface of the wind-tunnel test section, was used as an experimental model. The cube was subjected to the incidence flow at 40°. Steady and unsteady pressure measurements were performed on the cube surface. The analysis suggests that conical vortices developed above the top surface of the wall-mounted cube. A larger mean suction was observed on the top cube surface in the less turbulent boundary layer. With an increase in turbulence in the incoming flow, the strong suction zones decreased in size. The fluctuating pressure coefficient profiles retained their shape when the turbulence in the upstream flow of the cube increased. The fluctuating pressure coefficient was observed to be larger in more turbulent flows. The pressure fluctuations were larger on the cube surface underlying outer boundaries of the conical vortex. The fluctuating pressure coefficient under the conical vortex was three to four times larger than in the weak suction zone on the central area of the top cube surface. Close to the leading cube corner, the pressure spectra were dominated by a single low frequency peak. As the conical vortex developed, this primary peak weakened and a secondary peak emerged at a higher reduced frequency. There is a general trend of shifting the pressure spectra towards higher reduced frequencies when the turbulence in the undisturbed incident flow increases.     

Stereoscopic multi-planar PIV measurements of in-cylinder tumbling flow

The non-reacting flow field within the combustion chamber of a motored direct-injection spark-ignition engine with tumble intake port is measured. The three-dimensionality of the flow necessitates the measurement of all three velocity components via stereoscopic particle-image velocimetry in multiple planes. Phase-locked stereoscopic PIV is applied at 15 crank angles during the intake and compression strokes, showing the temporal evolution of the flow field. The flow fields are obtained within a set of 14 axial planes, covering nearly the complete cylinder volume. The stereoscopic PIV setup applied to engine in-cylinder flow and the arising problems and solutions are discussed in detail. The three-dimensional flow field is reconstructed and analyzed using vortex criteria. The tumble vortex is the dominant flow structure, and this vortex varies significantly regarding shape, strength, and position throughout the two strokes. The tumble vortex center moves clockwise through the combustion chamber. At first, the tumble has a c-shape which turns into an almost straight tube at the end of the compression. Small-scale structures are analyzed by the distribution of the turbulent kinetic energy. It is evident that the symmetry plane only represents the 3D flow field after 100 CAD. For earlier crank angles, both kinetic energy (KE) and turbulent kinetic energy (TKE) in the combustion chamber are well below the KE and TKE in the symmetry plane. This should be taken into account when the injection and breakup of the three-dimensional fuel jet are studied. The mean kinetic energy is conserved until late compression by the tumble motion. This conservation ensures through the excited air motion an enhancement of the initial air-fuel mixture which is of interest for direct-injection gasoline engines.     

Flow field characterization of a jet and vortex actuator

 An actuator, which produces several different flow fields that may be used for active flow control, is characterized in still air using flow visualization and velocity measurements. The primary actuator-induced flow fields are: free jets, wall jets, and vortex flows. The non-dimensional parameters governing these actuator-induced flows are developed. For the vortex-flow regime, the operational range of the actuator increases as it’s size decreases without a significant decrease in either the actuator induced velocity or vortex core size. The velocity scaling is developed for the vortex flow and suggests that the optimum actuator efficiency occurs at a Stokes number of approximately 7.9 for the range of parameters surveyed. In a turbulent, zero pressure gradient boundary layer, measurements made just downstream of the actuator (when operated in the vortex mode) indicate a vortical disturbance is generated in the boundary layer. Received: 2 September 1998/Accepted: 9 January 1999     

PIV study of large-scale flow organisation in slot jets

The paper reports on particle image velocimetry (PIV) measurements in turbulent slot jets bounded by two solid walls with the separation distance smaller than the jet width (5–40%). In the far-field such jets are known to manifest features of quasi-two dimensional, two component turbulence. Stereoscopic and tomographic PIV systems were used to analyse local flows. Proper orthogonal decomposition (POD) was applied to extract coherent modes of the velocity fluctuations. The measurements were performed both in the initial region close to the nozzle exit and in the far fields of the developed turbulent slot jets for Re ⩾ 10,000. A POD analysis in the initial region indicates a correlation between quasi-2D vortices rolled-up in the shear layer and local flows in cross-stream planes. While the near-field turbulence shows full 3D features, the wall-normal velocity fluctuations day out gradually due to strong wall-damping resulting in an almost two-component turbulence. On the other hand, the longitudinal vortex rolls take over to act as the main agents in wall-normal and spanwise mixing and momentum transfer. The quantitative analysis indicates that the jet meandering amplitude was aperiodically modulated when arrangement of the large-scale quasi-2D vortices changed between asymmetric and symmetric pattern relatively to the jet axis. The paper shows that the dynamics of turbulent slot jets are more complex than those of 2D, plane and rectangular 3D jets. In particular, the detected secondary longitudinal vortex filaments and meandering modulation is expected to be important for turbulent transport and mixing in slot jets. This issue requires further investigations.     

Flow above the free end of a surface-mounted finite-height circular cylinder: A review

The wake of a surface-mounted finite-height circular cylinder and the associated vortex patterns are strongly dependent on the cylinder aspect ratio and the thickness of the boundary layer on the ground plane relative to the dimensions of the cylinder. Above a critical aspect ratio, the mean wake is characterized by streamwise tip vortex structures and Kármán vortex shedding from the sides of the cylinder. Below a critical aspect ratio, a unique mean wake structure is observed. Recent experimental studies in the literature that used phase-averaged techniques, as well as recent numerical simulations, have led to an improved physical understanding of the near-wake vortex flow patterns. However, the flow above the free end of the finite circular cylinder, and its relationship to the near wake, has not been systematically studied. The effects of aspect ratio and boundary layer thickness on the free-end flow field are also not completely understood, nor has the influence of Reynolds number on the free-end flow field been fully explored. Common features associated with the free end include separation from the leading edge, a mean recirculation zone containing a prominent cross-stream arch (or mushroom) vortex, and reattachment onto the free-surface. Other flow features that remain to be clarified include a separation bubble near the leading edge, one or two cross-stream vortices within this separation bubble, the origins of the streamwise tip or trailing vortices, and various critical points in the near-surface flow topology. This paper reviews the current understanding of the flow above the free end of a surface-mounted finite-height circular cylinder, with a focus on models of the flow field, surface oil flow visualization studies, pressure and heat flux distributions on the free-end surface, measurements of the local velocity field, and numerical simulations, found in the literature.     

Recognition of coherent structures in the boundary layer of a low-pressure-turbine blade for different free-stream turbulence intensity levels

Particle Image Velocimetry (PIV) has been adopted to analyze the instantaneous flow field developing on a high-lift turbine blade profile operating under low and elevated free-stream turbulence conditions (FSTI). Results reported in the paper allow us to analyze the dynamics leading to transition and separation of the suction side boundary layer, looking to generation, propagation and breakdown of coherent structures observed in the two different FSTI cases. To this end, measurements have been performed in two orthogonal planes. Results obtained in the blade-to-blade plane allow the detailed characterization of the propagation of Kelvin–Helmholtz (KH) rolls generating, at low FSTI condition, as a consequence of a non-reattaching separation. Otherwise, data in the wall-parallel plane allow recognizing the presence of three-dimensional disuniformities induced at high FSTI by low and high speed streaks (Klebanoff mode). The sinuous breakdown of boundary layer streaks generates other complex three-dimensional coherent structures such as hairpin or cane-like vortices that induce transition. Proper Orthogonal Decomposition (POD) has been adopted to in depth characterize these structures, thus further explaining the mechanisms through which the free-stream turbulence intensity modify the transition/separation processes of the suction side boundary layer of an highly loaded low pressure turbine blade.     

横摆角下汽车尾部湍流特征量的PIV试验分析

汽车尾部湍流场是汽车压差阻力的主要来源,在HD-2汽车模型风洞中,首先使用测力天平和测压系统,对横摆角工况下汽车模型的气动六分力和纵对称截面48个测点的表面压力进行了测量,然后利用PIV测量技术对模型在横摆角分别为0°、15°的尾部湍流场进行了测量,获得该模型尾流场的速度场、涡量场和雷诺应力流场信息,通过计算得出尾流场区域空间相关系数和湍流积分尺度。结果表明:在横摆角工况下,汽车模型尾部涡流的结构呈现向上发展的趋势;尾流场拖拽涡的范围和强度的增大导致了模型气动力出现较大的增加;湍流积分尺度的变化表明,尾部涡流区的分离噪声与涡流分离位置有关,在汽车尾部造型设计中,要尽量推迟尾部涡流的分离。