Turbulent forced convection heat transfer of non-Newtonian nanofluids

Forced convection heat transfer of non-Newtonian nanofluids in a circular tube with constant wall temperature under turbulent flow conditions was investigated experimentally. Three types of nanofluids were prepared by dispersing homogeneously γ-Al₂O₃, TiO₂ and CuO nanoparticles into the base fluid. An aqueous solution of carboxymethyl cellulose (CMC) was used as the base fluid. Nanofluids as well as the base fluid show shear-thinning (pseudoplastic) rheological behavior. Results indicate that the convective heat transfer coefficient of nanofluids is higher than that of the base fluid. The enhancement of the convective heat transfer coefficient increases with an increase in the Peclet number and the nanoparticle concentration. The increase in the convective heat transfer coefficient of nanofluids is greater than the increase that would be observed considering strictly the increase in the effective thermal conductivity of nanofluids. Experimental data were compared to heat transfer coefficients predicted using available correlations for purely viscous non-Newtonian fluids. Results show poor agreement between experimental and predicted values. New correlation was proposed to predict successfully Nusselt numbers of non-Newtonian nanofluids as a function of Reynolds and Prandtl numbers.     

The variation of heat transfer in a two‐sided lid‐driven differentially heated square cavity with nanofluids containing carbon nanotubes for physical properties of fluid dependent on temperature

The behavior of nanofluids containing cylindrical nanoparticles are investigated numerically inside a two‐sided lid‐driven differentially heated square cavity to gain insight into the convective recirculation and flow processes induced by a nanofluid. The physical properties of the base fluid such as viscosity, thermal conductivity and thermal expansion coefficient are, respectively, assumed to be temperature independent (taking the mean temperature of the left and right walls) and temperature dependent. A model is developed to analyze the behavior of nanofluids taking into account the nanoparticle volume fraction whereas the transport equations are solved numerically with finite volume approach using SIMPLEC algorithm. The left and right moving walls are maintained at different constant temperatures while the upper and bottom walls are thermally insulated. The directions of the moving walls were considered in a way that the force and natural convections aid each other. The governing parameter Richardson number was 0.1<Ri<50.0 but due to space constraints only the results for 0.1<Ri<10.0 from fluid flow are presented. It was found that the temperature dependency of physical properties at different Richardson numbers and nanoparticle volume fractions affects the fluid flow and heat transfer in the cavities. Finally, comparisons between the behaviors of the average Nusselt number at the left wall for two cases are presented. Copyright © 2011 John Wiley & Sons, Ltd.     

Role of interfacial layer and clustering on the effective thermal conductivity of CuO-gear oil nanofluids

Copper oxide nanoparticles (∼40 nm) are dispersed in gear oil (IBP Haulic-68) at different volume fractions (0.005-0.025) with oleic acid added as a surfactant to stabilize the system. Prepared nanofluids are characterized by Fourier Transform Infrared spectroscopy (FTIR) and Dynamic light scattering (DLS) measurements. DLS data confirmed the presence of agglomerated nanoparticles in the prepared nanofluids. Thermal conductivity measurements are performed both as a function of CuO volume fraction and temperature between 5 and 80 °C. An enhancement in thermal conductivity at 30 °C of 10.4% with 0.025 volume fraction of CuO nanoparticle loading is observed. Measured volume fraction dependence of the thermal conductivity enhancement at room temperature is predicted fairly well considering contributions from both nanolayer at the solid-liquid interface and particle agglomeration in the suspension, as visualized by Feng et al.     

Hydraulic and heat transfer study of SiO2/water nanofluids in horizontal tubes with imposed wall temperature boundary conditions

The convective heat transfer of SiO₂/water colloidal suspensions (5-34 wt.%) is investigated experimentally in a flow loop with a horizontal tube test section whose wall temperature is imposed. Experiments were performed at different inlet temperatures (20, 50, 70 °C) in cooling and/or heating conditions at various flow rates (200 < Re < 10,000). The Reynolds and Nusselt numbers were deduced by using thermal conductivity and viscosity values measured with the same temperature conditions as those in the tests. Results indicate that the heat transfer coefficient values are increased from 10% to 60% compared to those of pure water. They also show that the general trend of standard correlations is respected. The problem of suspension stability at the highest temperatures is discussed. In order to evaluate the benefits provided by the enhanced properties of the nanofluids studied, an energetic performance evaluation criterion (PEC) is defined. This PEC decreases as the nanoparticle concentration is increased. This process is also discussed in this paper.     

Convective heat transfer of nanofluids with correlations

To investigate the convective heat transfer of nanofluids, experiments were performed using silver–water nanofluids under laminar, transition and turbulent flow regimes in a horizontal 4.3 mm inner-diameter tube-in-tube counter-current heat transfer test section. The volume concentration of the nanoparticles varied from 0.3% to 0.9% in steps of 0.3%, and the effects of thermo-physical properties, inlet temperature, volume concentration, and mass flow rate on heat transfer coefficient were investigated. Experiments showed that the suspended nanoparticles remarkably increased the convective heat transfer coefficient, by as much as 28.7% and 69.3% for 0.3% and 0.9% of silver content, respectively. Based on the experimental results a correlation was developed to predict the Nusselt number of the silver–water nanofluid, with ±10% agreement between experiments and prediction.     

Experimental investigation of forced convective heat transfer coefficient in nanofluids of Al2O3/EG and CuO/EG in a double pipe and plate heat exchangers under turbulent flow

Nanofluid is the term applied to a suspension of solid, nanometer-sized particles in conventional fluids; the most prominent features of such fluids include enhanced heat characteristics, such as convective heat transfer coefficient, in comparison to the base fluid without considerable alterations in physical and chemical properties. In this study, nanofluids of aluminum oxide and copper oxide were prepared in ethylene glycol separately. The effect of forced convective heat transfer coefficient in turbulent flow was calculated using a double pipe and plate heat exchangers. Furthermore, we calculated the forced convective heat transfer coefficient of the nanofluids using theoretical correlations in order to compare the results with the experimental data. We also evaluated the effects of particle concentration and operating temperature on the forced convective heat transfer coefficient of the nanofluids. The findings indicate considerable enhancement in convective heat transfer coefficient of the nanofluids as compared to the base fluid, ranging from 2% to 50%. Moreover, the results indicate that with increasing nanoparticles concentration and nanofluid temperature, the convective heat transfer coefficient of nanofluid increases. Our experiments revealed that in lower temperatures, the theoretical and experimental findings coincide; however, in higher temperatures and with increased concentrations of the nanoparticles in ethylene glycol, the two set of results tend to have growing discrepancies.     

Nanofluids thermal behavior analysis using a new dispersion model along with single-phase

A numerical study has been performed to analyze nanofluids convective heat transfer. Laminar α-Al₂O₃-water nanofluid flows in an entrance region of a horizontal circular tube with constant surface temperature. Numerical analysis has been carried out using two different single-phase models (homogenous and dispersion) and two-phase models (Eulerian–Lagrangian and mixture). A new model is developed to consider the nanoparticles dispersion. The transport equations for the tube with constant surface temperature were solved numerically using a control volume approach. The effects of nanoparticles volume fraction (0.5, 1 %) and Reynolds number (650 ≤ Re ≤ 2300) on nanofluid convective heat transfer coefficient were studied. The results are compared with the experimental data and it is shown that the homogenous single-phase model is underestimated and the mixture model is overestimated. Although the Eulerian–Lagrangian model gives a reasonable prediction for the thermal behavior of nanofluids, the dispersion single-phase model gives more accurate prediction despite its simplicity.     

On the quenching of steel and zircaloy spheres in water-based nanofluids with alumina,silica and diamond nanoparticles

The quenching curves (temperature vs time) for small (∼1 cm) metallic spheres exposed to pure water and water-based nanofluids with alumina, silica and diamond nanoparticles at low concentrations (?0.1 vol%) were acquired experimentally. Both saturated (ΔT_sub = 0 °C) and highly subcooled (ΔT_sub = 70 °C) conditions were explored. The spheres were made of stainless steel and zircaloy, and were quenched from an initial temperature of ∼1000 °C. The results show that the quenching behavior in nanofluids is nearly identical to that in pure water. However, it was found that some nanoparticles accumulate on the sphere surface, which results in destabilization of the vapor film in subsequent tests with the same sphere, thus greatly accelerating the quenching process. The entire boiling curves were obtained from the quenching curves using the inverse heat transfer method, and revealed that alumina and silica nanoparticle deposition on the surface increases the critical heat flux and minimum heat flux temperature, while diamond nanoparticle deposition has a minimal effect on the boiling curve. The possible mechanisms by which the nanoparticles affect the quenching process were analyzed. It appears that surface roughness increase and wettability enhancement due to nanoparticle deposition may be responsible for the premature disruption of film boiling and the acceleration of quenching. The basic results were also confirmed by quench tests with rodlets.     

Experimental investigation of TiO2/water nanofluid laminar forced convective heat transfer through helical coiled tube

Coiled tubes and nanofludics are two significant techniques to enhance the heat transfer ability of thermal equipments. The forced convective heat transfer and the pressure drop of nanofluid inside straight tube and helical coiled one with a constant wall heat flux were studied experimentally. Distilled water was used as a host fluid and Nanofluids of aqueous TiO₂ nanoparticles (50 nm) suspensions were prepared in various volume concentrations of 0.25–2 %. The heat transfer coefficient of nanofluids is obtained for different nanoparticle concentrations as well as various Reynolds numbers. The experiments covered a range of Reynolds number of 500–4,500. The results show the considerable enhancement of heat transfer rate, which is due to the nanoparticles present in the fluid. Heat transfer coefficient increases by increasing the volume concentration of nanoparticles as well as Reynolds number. Moreover, due to the curvature of the tube when fluid flows inside helical coiled tube instead of straight one, both convective heat transfer coefficient and the pressure drop of fluid grow considerably. Also, the thermal performance factors for tested nanofluids are greater than unity and the maximum thermal performance factor of 3.72 is found with the use of 2.0 % volume concentration of nanofluid at Reynolds number of 1,750.     

Measurement of temperature-dependent thermal conductivity and viscosity of TiO2-water nanofluids

Nanofluid is an innovative heat transfer fluid with superior potential for enhancing the heat transfer performance of conventional fluids. Many attempts have been made to investigate its thermal conductivity and viscosity, which are important thermophysical properties. No definitive agreements have emerged, however, about these properties. This article reports the thermal conductivity and dynamic viscosity of nanofluids experimentally. TiO₂ nanoparticles dispersed in water with volume concentration of 0.2–2 vol.% are used in the present study. A transient hot-wire apparatus is used for measuring the thermal conductivity of nanofluids whereas the Bohlin rotational rheometer (Malvern Instrument) is used to measure the viscosity of nanofluids. The data are collected for temperatures ranging from 15 °C to 35 °C. The results show that the measured viscosity and thermal conductivity of nanofluids increased as the particle concentrations increased and are higher than the values of the base liquids. Furthermore, thermal conductivity of nanofluids increased with increasing nanofluid temperatures and, conversely, the viscosity of nanofluids decreased with increasing temperature of nanofluids. Moreover, the measured thermal conductivity and viscosity of nanofluids are quite different from the predicted values from the existing correlations and the data reported by other researchers. Finally, new thermophysical correlations are proposed for predicting the thermal conductivity and viscosity of nanofluids.     

Experimental study of critical heat flux enhancement during forced convective flow boiling of nanofluid on a short heated surface

Enhancements of nucleate boiling critical heat flux (CHF) using nanofluids in a pool boiling are well-known. Considering importance of flow boiling heat transfer in various practical applications, an experimental study on CHF enhancements of nanofluids under convective flow conditions was performed. A rectangular flow channel with 10-mm width and 5-mm height was used. A 10 mm-diameter disk-type copper surface, heated by conduction heat transfer, was placed at the bottom surface of the flow channel as a test heater. Aqueous nanofluids with alumina nanoparticles at the concentration of 0.01% by volume were investigated. The experimental results showed that the nanofluid flow boiling CHF was distinctly enhanced under the forced convective flow conditions compared to that in pure water. Subsequent to the boiling experiments, the heater surfaces were examined with scanning electron microscope and by measuring contact angle. The surface characterization results suggested that the flow boiling CHF enhancement in nanofluids is mostly caused by the nanoparticles deposition of the heater surface during vigorous boiling of nanofluids and the subsequent wettability enhancements.     

Convective heat transfer of aqueous alumina nanosuspensions in a horizontal mini-channel

This work reports an experimental study of convective heat transfer of aqueous alumina nanofluids in a horizontal mini-channel under laminar flow condition 40 < Re < 1,000. The variation of local heat transfer coefficients, in both entrance and developed flow regimes, was obtained as a function of axial distance. The heat transfer coefficient of nanofluids was found to be dependent on not only nanoparticle concentration but also mass flow rate. Different to the behavior in conventional-sized channels, the major heat transfer coefficient enhancement is shown in the fully developed regime in the minichannel where up to 40% increase is observed. Discussions of the results suggest that apart from the need of a careful assessment of different thermo-physical properties of nanofluids, i.e., viscosity, specific heat and thermal conductivity, the heterogeneous nature of nanoparticle flow should be considered especially under high flow rate conditions.     

Laminar convective heat transfer of non-Newtonian nanofluids with constant wall temperature

Nanofluids are obtained by dispersing homogeneously nanoparticles into a base fluid. Nanofluids often exhibit higher heat transfer rate in comparison with the base fluid. In the present study, forced convection heat transfer under laminar flow conditions was investigated experimentally for three types of non-Newtonian nanofluids in a circular tube with constant wall temperature. CMC solution was used as the base fluid and γ-Al₂O₃, TiO₂ and CuO nanoparticles were homogeneously dispersed to create nanodispersions of different concentrations. Nanofluids as well as the base fluid show shear thinning (pseudoplastic) rheological behavior. Results show that the presence of nanoparticles increases the convective heat transfer of the nanodispersions in comparison with the base fluid. The convective heat transfer enhancement is more significant when both the Peclet number and the nanoparticle concentration are increased. The increase in convective heat transfer is higher than the increase caused by the augmentation of the effective thermal conductivity.     

Experimental study on convective heat transfer of TiO2 nanofluids

In this study, nanofluids with different TiO₂ nanoparticle concentrations were synthesized and measured in different constant heat fluxes for their heat transfer behavior upon flowing through a vertical pipe. Addition of nanoparticles into the base fluid enhances the forced convective heat transfer coefficient. The results show that the enhancement of the convective heat transfer coefficient in the mixture consisting of ethylene glycol and distilled water is more than distilled water as a base fluid.     

Investigation of the different base fluid effects on the nanofluids heat transfer and pressure drop

A numerical study of laminar forced convective flows of three different nanofluids through a horizontal circular tube with a constant heat flux condition has been performed. The effect of Al₂O₃ volume concentration 0 ≤ φ ≤ 0.09 in the pure water, water-ethylene glycol mixture and pure ethylene glycol as base fluids, and Reynolds number of 100 ≤ Re ≤ 2,000 for different power inputs in the range of 10 ≤ Q(W) ≤ 400 have been investigated. In this study, all of the nanofluid properties are temperature and nanoparticle volume concentration dependent. The governing equations have been solved using finite volume approach with the SIMPLER algorithm. The results indicate an increase in the averaged heat transfer coefficient with increasing the mass of ethylene glycol in the water base fluid, solid concentration and Reynolds number. From the investigations it can be inferred that, the pressure drop and pumping power in the nanofluids at low solid volumetric concentration (φ < 3%) is approximately the same as in the pure base fluid in the various Reynolds numbers, but the higher solid nanoparticle volume concentration causes a penalty drop in the pressure. Moreover, this study shows it is possible to achieve a higher heat transfer rate with lower wall shear stress with the use of proper nanofluids.     

Two numerical modelings of free convection heat transfer using nanofluids inside a square enclosure

This work describes the numerical simulation of natural convection heat transfer of Cu–water nanofluids in a square enclosure for Rayleigh numbers varying from 10³ up to 10⁵. Two different numerical approaches were used: the finite volume method and the finite element method. The nanofluids were assumed to be single-phase fluids with modified thermal properties obtained from experimental results and theoretical models. The results showed that the Nusselt number for nanofluids was basically the same as that obtained for the base fluid. Therefore, the enhancement observed in the heat transfer coefficient was significant due to the augmentation in the thermal conductivity.     

Solution of the equations of motion for a selectively radiating gas in a shock layer

Numerical solutions are obtained for the system of integro-differential equations describing the flow of a viscous, heat-conducting, selectively radiating gas in the region between the shock wave and a blunt body. The calculations are made for bodies of radius from 0.1 to 3 m with stagnation temperature from 6000° to 15 000° K. As a result of the calculations the convective and radiative thermal fluxes in the vicinity of the stagnation point are obtained. The effect of injection on convective and radiative heat transfer is studied.The first calculations of radiative thermal fluxes in air were made about 10 years ago in [1,2]. However, the results did not take account of the effects of emission and reabsorption, nor the interaction of the convective and radiative heating processes. These effects have been studied primarily with the use of simplified models of a radiating gas. Most often the approximation used is that of a gray gas with absorption coefficient which is independent of wavelength ([3–6] and others).The appearance in the literature of quite detailed data on the selective spectral absorption coefficients of air over a wide temperature range [7,8] has made it possible to solve the direct problem of calculating the flow field of a selectively radiating gas behind a shock wave with account for all the effects mentioned above.     

Electro-magneto-hydrodynamic flow of couple stress nanofluids in micro-peristaltic channel with slip and convective conditions

This study explores the effects of electro-magneto-hydrodynamics, Hall currents, and convective and slip boundary conditions on the peristaltic propulsion of nanofluids(considered as couple stress nanofluids) through porous symmetric microchannels. The phenomena of energy and mass transfer are considered under thermal radiation and heat source/sink. The governing equations are modeled and non-dimensionalized under appropriate dimensionless quantities. The resulting system is solved numerically w...     

Heat Transport in Unsaturated Zone Thermal Energy Storage – Analysis with Two-Phase and Single-Phase Models

We analyze a field experiment where ambient air is injected into the soil during the summer and extracted again during the winter. A multiphase model accounting for the conductive transport as well as the convective transport with the moving liquid and gas phases is used along with a more simplified single-phase model where the convective transport is due to the gas alone. The latter model also accounts for subzero wintertime temperatures. The multiphase model captures well both the seasonal variations and the actual test sequence, the main calibration being in the adjustment of medium permeabilities based on the observed pressure responses. The effect of the injection pump on the temperature and humidity of the injection air needs to be known accurately. Taking into account the humidity of the injection air explicitly instead of using humidity-corrected enthalpy values also has an effect. The effect of various humidity and specific enthalpy assumptions is of the order of 1–1.5°C, while ignoring the wintertime subzero temperatures has an effect of 1–2°C. These differences are of the same order of magnitude as the heterogeneity-introduced differences in field data. Using the simplified single-phase model typically appears to cause a difference of 1–2°C, but can yield an even higher deviation of the order of 3–4°C.     

Carbon nanotube glycol nanofluids: Photo-thermal properties,thermal conductivities and rheological behavior

The efficiency and effectiveness of solar energy capture and storage are to a large extent functions of the heat transfer and storage capacity of the medium used. This paper investigates the potential of using carbon nanotube (CNT)-glycol nanosuspension as such a medium, prepared by freeze drying-ultrasonic dispersing after oxidation treatment with HNO₃. The influences of the mass fraction of CNTs glycol nanofluids and temperatures on photo-thermal properties, thermal conductivities and rheological behavior were investigated. The results show that CNTs with oxidation treatment exhibited good dispersing performance. Strong optical absorption of the CNTs glycol nanofluids was detected in the range of 200–2500 nm. At room temperature, 18% enhancement was found in the photo-thermal conversion efficiency of the 0.5% mass fraction CNTs glycol nanofluids in comparison to the basic fluids, without significant increase in viscosity. At 55 °C, CNTs glycol nanofluids with 4.0% mass fraction exhibited much lower viscosity and 25.4% higher thermal conductivity in comparison to that of pure glycol at room temperature.