Solvent extraction behaviour of lanthanum(III), cerium(III), europium(III), thorium(IV) and uranium(VI) with 3-phenyl-4-benzoyl-5-isoxazolone

The extraction behaviour of La(III), Ce(III), Eu(III), Th(IV) and U(VI) with 3-phenyl-4- benzoyl-5-isoxazolone (HPBI) in chloroform has been studied. The mechanism of extraction and the species extracted have been identified. Extraction constants for each system have been calculated. The system has been used to separate Th(IV) from U(VI) and from La(III), Ce(III) and Eu(III). A comparison of the extraction constants with those for the 1-phenyl-3-methyl-4-benzoyl-5-pyrazolone (HPMBP) and thenoyltrifluoroacetone (HTTA) systems indicates that HPBI extracts these metal species better than HPMBP and HTTA do.     

A chelating resin containing trihydroxybenzoic acid as the functional group: synthesis and adsorption behavior for Th(IV) and U(VI) ions

A novel glycidyl methacrylate chelating resin has been synthesized through copolymerization of glycidyl methacrylate (GMA) in the presence of divinylbenzene (DVB), the resulting resin was immobilized with 3,4,5-trihydroxybenzoic acid (THBA) to give GMA/DVB/THBA chelating resin. The adsorption of Th(IV) and U(VI) on GMA/DVB/THBA adsorbent was studied as a function of initial concentration, pH, shaking time and temperature. The novel chelating resin shows a high capacity for Th(IV) and U(VI), maximum adsorption of Th(IV) and U(VI) were 56 and 83.6 mg/g, respectively. Kinetic studies showed that the adsorption follows the pseudo second order model referring to the influence of the textural properties of the resin on the rate of adsorption. Thermodynamic parameters such as ?H° and ?S° were studied and indicated an endothermic process.     

Extraction of uranium(VI) and thorium(IV) from nitric acid solution by N-alkylcaprolactam

Extraction of uranium(VI), thorium(IV) from nitric acid has been studied with N-octylcaprolactam and N-(2-ethyl)hexylcaprolactam. Distribution coefficients of U(VI), Th(IV) and HNO₃ as a function of aqueous NHO₃ concentration, extractant concentration and temperature have been studied. The compositions of extracted species, thermodynamic parameters of extraction have been evaluated. Third phase formation in extraction of U(VI) has been studied. Back extraction behavior of U(VI) and Th(IV) from the organic phase has also been tested. The results obtained are compared with those obtained by using TBP under the same experimental conditions.     

Sorption study of U(VI), Th(IV) and Ce(III) on poly[dibenzo-18-crown-6] in <Emphasis Type="SmallCaps">l</Emphasis>-arginine to develop sequential column chromatographic separation method

A simple and efficient column chromatographic method has been developed for the sequential separation of U(VI), Th(IV) and Ce(III) using poly[dibenzo-18-crown-6] as stationary phase and l-arginine as a counter ion. The different elution patterns with various eluting agents were observed for individual element. The capacity of poly[dibenzo-18-crown-6] for U(VI), Th(IV) and for Ce(III) was found to be 0.96, 0.86 and 1.49 (±0.01) mmol/g of crown polymer, respectively. The method is efficient to separate the elements in multicomponent mixtures and has good recovery. The method is extended to determine the U(VI), Th(IV) and Ce(III) from monazite sand. The method is simple, rapid and selective having good reproducibility (~±2%).     

Kinetic studies on the solvent extraction of uranium (IV), thorium (IV) and uranium (VI) from nitric acid solutions with tributyl phosphate

The kinetics of solvent extraction of U (IV), Th (IV) and U (VI) from nitric acid solution with tributyl phosphate (TBP) in kerosene and cyclohexane have been studied using the single drop technique. The effects of concentrations of U (IV), Th (IV), U (VI), nitric acid, nitrate, TBP and temperature on the extraction rates of U (IV), Th (IV) and U (VI) have been examined. The mechanisms for the three extraction processes are discussed.     

New extractants for reprocessing of spent Th-U fuel

A study on solvent extraction of U(VI), Th(IV) and HNO₃ from nitric acid media by DEHSO is described. Extraction coefficients of U(VI), Th(IV) and HNO₃ as a function of aqueous HNO₃ concentration, extractant concentration and temperature have been studied. From the data the compositions of extracted species, equilibrium constants and enthalpies of extraction reaction have been evaluated. Back-extraction of U(VI) and Th(IV) from the organic phase by dilute nitric acid has also been tested. All studies on DEHSO are compared with TBP.     

Synthesis of N,N′-dimethyl-N,N′-dibutyl malonamide functionalized polymer and its sorption affinities towards U(VI) and Th(IV) ions

A novel chelating polymeric material was synthesized by chemical anchoring of N,N′-dimethyl-N,N′-dibutyl malonamide (DMDBMA) with chloromethylated polystyrene-divinyl benzene polymer. The polymeric material thus prepared was characterized by ¹³C NMR, FT-IR spectroscopy and CHN elemental analysis. The fabricated polymeric material exhibited superior binding for hexa-valent and tetra-valent metal ions such as U(VI) and Th(IV). Various physico-chemical properties of the functionalized polymer like phase adsorption kinetics, metal sorption mechanism and metal sorption capacity was studied in the static method. Adsorption kinetics studies show that <20 min was sufficient for >99.99% adsorption of Th(IV) and U(VI). The kinetics for adsorption of U(VI) and Th(IV) was found to follow the first order Lagergren rate kinetics. Adsorption of U(VI) on the malonamide functionalized polymer followed the Langmuir adsorption isotherm. The Langmuir monolayer adsorption phenomenon was also confirmed by the theoretical approach calculated based on the adsorption kinetics. The metal sorption capacities for uranium and thorium were found to be 18.78 ± 1.53 mg and 15.74 ± 1.59 mg/g of the chelating polymer at 3 M HNO₃, respectively.     

The effect of previous gamma-irradiation on the extraction of U(VI), Th(IV), Zr(IV), Eu(III) and Am(III) by various amides

The extraction behavior of U(VI), Th(IV), Zr(IV), Eu(III) and Am(III) from 3.5M nitric acid with a series of gamma-pre-irradiated symmetrical and unsymmetrical monoamides in benzene has been investigated up to a dose of 100 Mrad. The results indicated that the radiolytic stability is influenced by the structure of amides. Symmetrical monoamides seem to be less affected by radiation compared with unsymmetrical monoamides. Infrared studies identify the final products of radiolysis as the respective carboxylic acids and amines. The radiolytic degradation of the investigated monoamides has been estimated by quantitative IR spectroscopy. Extraction data obtained under similar experimental conditions for U(VI), Th(IV) and Zr(IV) with the TBP/benzene system have also been compared. This revised version was published online in August 2006 with corrections to the Cover Date.     

An effective process for the separation of U(VI), Th(IV) from rare earth elements by using ionic liquid Cyphos IL 104

Separation and recovery of U(VI) and Th(IV) from rare earth minerals is a very challenging work in rare earth industrial production. In the present study, a homemade membrane emulsification circulation (MEC) extractor was used to separate U(VI) and Th(IV) from rare earth elements by using Cyphos IL 104 as an extractant. Batch experiments were carried out using a constant temperature oscillator to investigate the extraction parameters of the single element and the results indicated that Cyphos IL 104 could reach the extraction equilibrium within 30 min for all the three elements, i.e., U(VI), Th(IV), and Eu(III). Besides, the MEC extractor possessed a strong phase separation ability. The extraction efficiencies of U(VI), Th(IV), La(III), Eu(III) and Yb (III) increased with the increase of pH. La(III), Eu(III) and Yb(III) were hardly extracted when pH ≤ 1.50, which was beneficial for effectively separating U(VI) and Th(IV) from La(III), Eu(III) and Yb(III). In the multi-stages stripping experiments, when the stripping stage number was 3, the effective separation could be achieved by using HCl and H₂SO₄, since the stripping efficiency reached 80.0% and 100.0% for Th(IV) and U(VI), respectively. Slope method and FT-IR spectra showed that Cyphos IL 104 reacted with U(VI) and Th(IV) by chelation mechanism. The extraction of multi-elements indicated that U(VI) and Th(IV) could be well separated from the solution which contains all rare earth elements, and the extraction efficiencies of U(VI) and Th(IV) both were close to 100.0%. Based on the above experimental results, a flowchart for efficient separation of U(VI) and Th(IV) from rare earth elements was proposed.     

Uranium(VI) and Thorium(IV) Adsorption Studies on Chelating Resin Containing Pentaethylenehexamine as a Functional Group

A new chelating resin (glycidyl methacrylate/divinylbenzene/pentaethylenehexamine (GMA/DVB/PEHA)) for uranium(VI) and thorium(IV) has been developed by functionalizing GMA/DVB with PEHA. The adsorption of U(VI) and Th(IV) ions onto the functionalized GMA/DVB/PEHA were investigated as a function of pH value, contact time, and temperature using batch adsorption technique. The results showed that U(VI) and Th(IV) adsorption onto GMA/DVB/PEHA was strongly dependent on pH. Kinetic studies revealed that the adsorption process achieved equilibrium within 15 and 90 minutes for Th(IV) and U(VI), respectively, and followed a pseudo-second-order rate equation. The isothermal data correlated with the Langmuir model better than the Freundlich model. Thermodynamic data indicated the spontaneous and endothermic nature of the process. The maximum adsorption capacity of U(VI) and Th(IV) were found to be 114 and 78 mg/g, respectively. Quantitative recovery of uranium and thorium were achieved by desorbing the loaded GMA/DVB/PEHA with 0.5 M HNO₃      

The solvent extraction of UO 2 2+ and Th4+ with petroleum sulfoxide

The influence of the concentration of nitric, hydrochloric and phosphoric acids, petroleum sulfoxides (PSO), salting-out agent, kind of diluent and temperature on the distribution ratio of U(VI) and Th(IV) has been systematically studied. It is found that the extraction regularity of PSO is similar to that of TBP. The distribution ratio in phosphoric acid is lower, but it increases with the increase of hydrochloric acid concentration and reaches a high value. The U(VI) exhibits the maximum distribution ratio at 3–4 mol/l HNO₃. The distribution ratio of U(VI) and Th(IV) increases rapidly in the presence of a salting out agent. The extracted compounds are determined to be UO₂(NO₃)₂2PSO and Th(NO₃)₄2PSO. The extraction enthalpies of U(VI) and Th(IV) with PSO were also calculated.     

Rapid and selective method for the spectrophotometric determination of tin using potassium ethylxanthate

Tin (II) forms a yellow complex with potassium ethylxanthate which can be extracted into chloroform. Tin is determined spectrophotometrically by measuring the absorbance at 360 nm. Beer's law is obeyed up to 120 g of Sn in the aqueous phase with a Sandell sensitivity of 0.013 g Sn/cm². Metal ions such as Ti(IV), Cr(VI), Mn(II), Cu(II), Zn(II), Al(III), U(VI), W(VI), Th(IV) and Zr(IV) do not interfere, but Mo(VI), Co(II) and Bi(III) do. Interference due to Fe(II, III), Ni(II) and V(V) is checked by suitable masking agents. Analysis of some synthetic and industrial samples has been carried out by the proposed method.     

Extraction of U(VI), Zr(IV) and Th(IV) from perchlorate media, by PC-88A

Extraction of U(VI), Zr(IV) and Th(IV) has been investigated from perchlorate media using 2-ethylhexyl phosphonic acid mono-2-ethylhexyl ester (PC-88A) dissolved in toluene. The extraction of U(VI), Zr(IV) and Th(IV) was found to be quantitative in the pH range 1.6 to 3.2, 2.0 to 4.7 and 2.3 to 3.8, respectively, with 3.0^.10^-3, 5.6^.10^-4 and 1.0^.10^-2M PC-88A dissolved in toluene. U(VI) was stripped with 4.0M HCl, Zr(IV) with 2.5M NaF and Th(IV) with 8.0M HCl from the metal loaded organic phase containing PC-88A dissolved in toluene. The probable extracted species have been ascertained by plotting log D vs. log [HR] as UO₂R₂ ^.2HR, ZrR₄ ^.2HR and ThR₄ ^.4HR, respectively. U(VI) was separated from Zr(IV) and Th(IV) and from other associated metals. This method was proved by the determination of U(VI) in some real samples.     

Competitive adsorption of uranium(VI) and thorium(IV) ions from aqueous solution using triphosphate-crosslinked magnetic chitosan resins

The triphosphate-crosslinked magnetic chitosan resins (TPP-MCR) with a diameter range of 200–350 nm were synthesized for the adsorption of U(VI) and Th(IV) ions from aqueous solutions. The adsorption experiments were conducted in both mono-component systems with pure actinide solution and bi-component systems with different U/Th mass ratios. The maximum adsorption capacities in mono-component systems determined by Langmuir model were 169.5 and 146.8 mg g^?1 for U(VI) and Th(IV), respectively. In bi-component systems, U(VI) and Th(IV) adsorption capacities were reduced significantly, and the combined sorption capacities were substantially lower (almost halved) compared to those obtained by the addition of sorption capacities using mono-component solutions, indicating that U(VI) and Th(IV) compete for the same sorption sites. Adsorption–desorption experiments for five cycles illustrated the feasibility of the repeated use of TPP-MCR for the adsorption of U(VI) and Th(IV) ions.     

A new procedure for the spectrophotometric determination of uranium(VI) in the presence of a large excess of thorium(IV).

Spectrophotometric determination of microgram amounts of U(VI) with 2-(5-Bromo-2-Pyridylazo)-5-diethylaminophenol (Br-PADAP), originally developed by Johnson and Florence has been modified to enable the determination of U(VI) in the presence of a large excess of Th(IV). The effects of thorium, tri-n-butyl phosphate (TBP) and ethanol on the estimation of uranium have been studied in detail and are presented in this paper. This modified method can be applied for the analysis of U(VI) both in aqueous and organic samples containing a large excess of Th(IV) (Th:U = 10000:1).     

Adsorption Studies of Radionuclides and Toxic Metal Ions on a Modified Mesoporous Lanthanum(III) Silicate

A new adsorbent, modified mesoporous lanthanum(III) silicate, has been prepared with various molar ratios of Si/La (10, 20, 40, 80) and cethyltrimethylammonium bromide (CTAB) as structure directing agent. XRD, nitrogen sorption, SEM, IR, thermogravimetry and sorption of radionuclides and toxic metal ions have been studied. The results show that adsorption amount of some element such as Pb(II) and Th(IV) has been increased significantly by incorporation of lanthanum ions in the framework of adsorbent. Separation of Co(II)‐Th(IV), Co(II)‐U(VI) and Mo(VI)‐U(VI) has been developed on columns of this adsorbent.     

Solubility, dissociation and complexation with Nd(III) and Th(IV) of oxine, thenoyltrifluoroacetone and 1,10-phenanthroline in 5.0 m NaCl

Equilibria in the system of Nd(III) and Th(IV) with 8-hydroxyquinoline (oxine), thenoyltrifluoroacetone (HTTA) and 1,10-phenanthroline (phen) in 5.0 m NaCl solution have been investigated by spectroscopy and potentiometry. The solubility and deprotonation constants of the three organics were measured to be: pK_s = 3.09 ± 0.01, pK_a1 = 5.82 ±0.02, pK_a2= 10.00 ±0.01 for oxine; pK_s = 2.49 ± 0.01, pK_a1 = 6.47 ±0.03 for HTTA; pK_s = 2.86 ± 0.02, pK_a2 = 5.82 ± 0.05 for phen. The stabilities of the corresponding metal complexes are in the order M(oxine) > M(TTA) > M(phen), where M = Nd(III), Th(IV). For all three organic ligands, the Th(IV) complexation is stronger than that of Nd(III).     

Simultaneous derivative spectrophotometric determination of thorium and uranium in a micellar medium

Derivative photometric methods for trace analysis of Th(IV) and UO₂(II), and their simultaneous determination in mixtures using 5,8-dihydroxy-1,4-naphthoquinone in a micellar medium are reported. Molar absorptivity and Sandell's sensitivity of 1:2 Th(IV) and 1:1 UO₂(II) complexes at their λ_max, 614.5 nm and 637.0 nm are, 1.19 × 10⁴ 1/mol/cm and 1.12 × 10⁴ 1/mol/cm and 1.95 × 10⁻² μg/cm² and 2.13 × 10⁻² μg/cm² μg/cm², respectively. Calibration graph is linear over the range 9.28 × 10⁻²−18.56 μg/ml of Th(IV) and 9.52 × 10⁻²−19.04 μg/ml of UO₂(II). Though presence of Th(IV) and UO₂(II) causes interference in each others determination, 9.28 × 10⁻¹−9.28 μg/ml Th(IV) and 9.52 × 10⁻¹−9.52 μg/ml UO₂(II) when present together, can be simultaneously determined using derivative spectra.     

Separation of Th/IV/ and U/VI/ by extraction chromatography

Application of extraction chromatographic technique to the analytical separation of Th/IV/ and U/VI/ has been investigated. The stationary phase was a macroporous resin Amberlite XE-270 impregnated with undiluted trin-n-butylphosphate /TBP/ and the mobile phase was either 5.OM HNO₃ or 6M HCl. Separation of traces of Th/IV/ from large quantities of U/VI/ was achieved on a laboratory column by elution of the absorbed Th/IV/ with 6M HCl.     

Preconcentration of uranium(VI) and thorium(IV) from aqueous solutions using low-cost abundantly available sorbent

Olive cake as low-cost abundantly available sorbent has been characterized by N₂ at 77 K adsorption, porosity analysis, elemental analysis and IR spectra and has been used for preconcentrating of uranium(VI) and thorium(IV) ions prior to their determination spectrophotometrically. The optimum pH values for quantitative sorption of U(VI) and Th(IV) are 4–7 and 3–7, respectively. The enrichment factor for the preconcentration of U(VI) and Th(IV) were found to be 125 and 75 in the given order. The sorption capacity of olive cake is in the range of 2,260–15,000 μg g⁻¹ for Th(IV) and in the range of 1,090–17,000 μg g⁻¹ for U(VI) at pH 3–7. The sorbent exhibits good reusability and the uptake and stripping of the studied ions were fairly rapid. The elution of U(VI) and Th(IV) was performed with 0.3–1 M HCl/1–2 M HNO₃ and 0.3–0.8 M HCl/1 M HNO₃, respectively. The precision of the method was 1.8 RSD% for U(VI) and 2.5 RSD% for Th(IV) in a concentration of 1.00 μg mL⁻¹ for 10 replicate analysis. The influence of some electrolytes and cations as interferents was discussed. Separation of U(VI) and Th(IV) from other metal ions in synthetic solution was achieved.