Non-aqueous sol–gel preparation of carbon-supported nickel nanoparticles

This work addresses the novel non-aqueous sol–gel process preparation of carbon-supported nickel nanoparticles. In the sol–gel process, ethanol, nickel nitrate or nickel (П) acetylacetonate, and citric acid were used as solvent, source of metallic element, and chelating agent, respectively. Hexadecylamine (HDA), oleic acid and oleylamine were used as surfactants. The calcination process was performed under protecting Ar or N₂ flowing. Carbon supported nickel nanoparticles can be prepared by this sol–gel process. Moreover, no grain growth occurs in a temperature range of 200 K, meaning that the grain size of the nickel nanoparticles can be controlled in this sol–gel process. The nickel nanoparticles can display typical superparamagnetic behavior at room temperature when HDA has been used. This novel method is expected to have wide applications in the field of metallic nanoparticles.     

Pure face-centered-cubic (fcc) and hexagonal-close-packed (hcp) nickel phases obtained in air atmosphere sol–gel process and fcc nickel phase obtained in N2 protected sol–gel process

Air atmosphere sol–gel process is often applied to prepare metallic oxide materials. Here we show that metallic nickel phase can also be obtained by citric acid (CA) based air atmosphere sol–gel process in appropriate procedure. Pure fcc or hcp phases of nickel can be obtained in air atmosphere by using CA, nickel (II) acetylacetone, organic solvents and organic surfactants such as oleylamine (OAM), hexadecylamine. However, only NiO can be prepared by aqueous CA based sol–gel process. Oleic acid and OAM can also be used in organic solution mediated sol–gel process to prepare nickel nanoparticles in N₂ atmosphere with pure fcc phase at appropriate calcination temperature when 1-hexyl alcohol has been used as solvent. Impurities, such as hcp Ni or Ni₃N phase, do not occur in this experimental condition. Our results provide a new and facile way in preparation of metallic nanoparticles.     

The properties of nickel aluminate nanoparticles prepared by sol–gel and impregnation methods

Nickel aluminates were prepared by sol–gel and impregnation methods and calcined at 1100 °C. The sol–gel made samples were prepared with different amounts of nickel (Ni/Al molar ratio equal to 0, 0.25, 0.5, and 0.75) and aging times (24 and 48 h). The samples were characterized by X-ray diffraction, induced couple plasma, nitrogen physisorption, transmission and scanning electron microscopy, and ammonia temperature programmed desorption (NH₃-TPD). In the sol–gel made samples, only the NiAl₂O₄ structure of nickel aluminate was defined, while for impregnation, NiAl₁₀O₁₆ was formed as well. The sol–gel made samples had low specific surface areas (7.7–12.4 m²/g), but a sample prepared by impregnation method had higher specific surface area (67.2 m²/g). The surface acidity density decreased by increasing the amount of nickel and was the lowest for impregnation method.     

Synthesis and Characterization of High Surface Area Tin Oxide Nanoparticles via the Sol‐Gel Method as a Catalyst for the Hydrogenation of Styrene

A systematic study on the preparation of SnO₂ nanoparticles using a simple sol‐gel technique has been conducted by varying reaction parameters such as concentration of ammonia, ammonia feed rate and reaction temperature. The tin oxide obtained was characterized by using FTIR, BET, XRD and TEM. Particles size was obtained in the range of 4 to 5.6 nm and the surface area was found to be between 76 to 114 m² g^?1 depending on the reaction parameters. Meanwhile, the catalytic activity of SnO2 was first time investigated for the hydrogenation reaction of styrene using ethanol as the solvent at 70 °C and 1 atmospheric pressure. It is found that SnO2 acts as a good catalyst in this hydrogenation process. The product conversions in the presence of catalysts prepared at different conditions were between 37 to 72%.     

Nanosized nickel oxide particles and modification with poly(methyl methacrylate)

In recent years, there is an increasing interest in the fabrication of inorganic–organic materials considering the remarkable change and improvement in properties. In this investigation, nanosized nickel oxide (NiO) particles were first prepared by calcination of nickel hydroxide precursor obtained by a simple liquid‐phase process. Mixed phases of NiO and nickel hydroxide were present as the calcination temperature was lower than 250°C. Non‐stoichiometric NiO was formed between 250°C and 350°C, and a pure NiO was obtained as the temperature reached 500°C. The surface characteristics of NiO particles were evaluated by measuring the adsorption behavior of anionic and cationic surfactants and some biomolecules. NiO/poly(methyl methacrylate) composite particles were then prepared using variable NiO/methyl methacrylate (MMA) ratio by seeded emulsion polymerization. The efficiency of NiO incorporation in the composite increased as the MMA content was increased in the recipe. The composite particles were colloidally stable, and the obtained particles were characterized by Fourier transform infrared, scanning electron microscopy, X‐ray diffraction, and X‐ray photoelectron spectra. Copyright © 2011 John Wiley & Sons, Ltd.     

硬脂酸前驱体法制铁酸锌脱硫剂及其在中温下的应用

以硬脂酸为凝胶剂，经由溶胶、凝胶、煅烧等步骤直接合成了晶体尺寸为纳米级(15nm～32nm)的铁酸锌脱硫剂，并应用TG-DTA、XRD、BET等测试手段对干凝胶及所得产品进行分析表征。结果表明，硬脂酸前驱体法合成温度低，操作简便。随着煅烧温度的升高，产品的比表面积减小，平均粒径增大，脱硫性能变差；该法制备的脱硫剂在350℃~550℃活性高，脱硫精度高，硫容大，而且再生性能良好，450℃下完全再生。     

Investigation of Fe−Ni Mixed‐Oxide Catalysts for the Reduction of NO by CO: Physicochemical Properties and Catalytic Performance

A series of Fe?Ni mixed‐oxide catalysts were synthesized by using the sol–gel method for the reduction of NO by CO. These Fe?Ni mixed‐oxide catalysts exhibited tremendously enhanced catalytic performance compared to monometallic catalysts that were prepared by using the same method. The effects of Fe/Ni molar ratio and calcination temperature on the catalytic activity were examined and the physicochemical properties of the catalysts were characterized by using XRD, Raman spectroscopy, N₂‐adsorption/‐desorption isotherms, temperature‐programmed reduction with hydrogen (H₂‐TPR), temperature‐programmed desorption of nitric oxide (NO‐TPD), and X‐ray photoelectron spectroscopy (XPS). The results indicated that the reduction behavior, surface oxygen species, and surface chemical valence states of iron and nickel in the catalysts were the key factors in the NO elimination. Fe_0.5Ni_0.5O_x that was calcined at 250 °C exhibited excellent catalytic activity of 100 % NO conversion at 130 °C and a lifetime of more than 40 hours. A plausible mechanism for the reduction of NO by CO over the Fe?Ni mixed‐oxide catalysts is proposed, based on XPS and in situ diffuse reflectance infrared Fourier transform spectroscopy (DRIFTS) analyses.     

Synthesis of Fe‐MCM‐41 from silatrane and FeCl3 via sol–gel process and its epoxidation acivity

An iron‐containing mesoporous molecular sieve, or Fe‐MCM‐41, was successfully synthesized the via sol–gel technique using silatrane and FeCl₃ as the silicon and iron sources, and was characterized using various techniques. Many factors were investigated, namely, reaction temperature and time, calcination rate, and iron amount in the reaction mixture. It was found that the optimum conditions in which to synthesize Fe‐MCM‐41 was to carry out the reaction at 60 °C for 7 h using a 1 °C min^?1 calcination rate and a 550 °C calcination temperature. The catalytic activity and selectivity of styrene epoxidation using hydrogen peroxide showed that the selectivity of the styrene oxide reached 65% at a styrene conversion of 22% over the 1%wt catalyst. Copyright © 2008 John Wiley & Sons, Ltd.     

Mullite fibers prepared from an inorganic sol–gel precursor

Mullite fibers were prepared by sol–gel process using alumina sol and silica sol. Alumina sol was synthesised from dissolution of aluminum powder in aluminum chloride hexahydrate solution. The optimal spinning alumina sol could be obtain in the composition range of Al/AlCl₃·6H₂O molar ratio 3.4–3.8. The Al and Si components were mixed at the molecular level and linear molecules were formed in the mullite precursor sol. The dried mullite precursor gel fibers completely transformed to mullite fibers at 1,000 °C with a smooth surface and uniform diameter.     

Sol–gel process of carbon-supported nickel nanoparticles using different solvents and protecting atmospheres

Carbon-supported nickel nanoparticles have been prepared by a sol–gel process under N₂ or H₂ atmospheres using different solvents such as distilled water, ethanol, acetone and 1-propanol. In the aqueous sol–gel process, nickel nanoparticles with pure face-centered-cubic (fcc) phase can be obtained under N₂ atmosphere by using nickel nitrate, tartaric acid and sodium dodecyl sulfonate. When organic solvents are applied, nickel (Π) acetylacetone is required in order to obtain nickel nanoparticles with pure fcc phase under N₂ atmosphere. When the protecting atmosphere is H₂, nickel nitrate can be used to obtain nickel particles with pure fcc phase. Nickel nanoparticles with grain sizes of 4–6 nm in diameter can be prepared by using nickel (Π) acetylacetone [Ni(acac)₂], citric acid and hexadecylamine with solvent being acetone. 1-propanol is also effective in the preparation of nickel nanoparticles in this sol–gel process. We suggest that this sol–gel may be used for other metallic nanocrystals.     

Electrospun titania sol–gel‐based ceramic composite nanofibers for online micro‐ solid‐phase extraction with high‐performance liquid chromatography

Titanium(IV) tetraisopropoxide was employed as a metal oxide sol–gel precursor to prepare ceramic composite nanofibers by the electrospinning system. To facilitate this process and obtain the desired nanofibers with higher aspect ratios and surface area, poly(vinylpyrrolidone) was added to the sol of titania. Four ceramic nanofibers sheets based on titania were prepared while each sheet contained different transition metals such as Fe‐Mn, Fe‐Ni, Fe‐Co, and Fe‐Mn‐Co‐Ni. The scanning electron microscope images showed good homogeneity for all the prepared ceramic composites with a diameter range of 100–250 nm. The sorption efficiency was investigated by a micro‐solid‐phase extraction setup in online combination with high‐performance liquid chromatography for the determination of naproxen and clobetasol. All the prepared composites exhibited comparable efficiencies for the desired analytes and the type of metal showed insignificant effect. For the selected composite with Fe‐Mn, the linearity of the analytes was in the range of 1–1000 μg/L and the limit of detection values were found to be 2 and 0.3 μg/L for naproxen and clobetasol, respectively. The developed method was extended to the analysis of urine and blood plasma samples and acceptable relative standard deviations were obtained at two concentration levels.     

Crack‐free sol‐gel coatings for protection of AA1050 aluminium alloy

Organically modified sol‐gel coatings have been investigated as potential replacements for chromate conversion treatments of an AA1050 aluminium alloy. The coatings were prepared by combination of a completely hydrolysable precursor of tetra‐n‐propoxyzirconium (TPOZ), with a partially hydrolysable precursor of glycidoxypropyltrimethoxysilane (GPTMS). GPTMS contains an organic functional group, which is retained in the sol‐gel coatings after the hydrolysis–condensation process. Different GPTMS/TPOZ ratios and withdrawal speeds were studied. Coatings produced using a low GPTMS/TPOZ ratio and a high withdrawal speed generated significant cracks due to the shrinkage of the coatings, with no corrosion protection of the alloy. It was found that increase of organic moieties reduced the shrinkage of the coatings and the tendency for crack formation. By control of process parameters and ratios of organic and inorganic moieties, crack‐free sol‐gel coatings above 1 µm thick, with improved corrosion protection, can be produced on the alloy surface. Copyright © 2010 John Wiley & Sons, Ltd.     

Hydrogen production via CO2-reforming of methane over Cu and Co doped Ni/Al2O3 nanocatalyst: impregnation versus sol–gel method and effect of process conditions and promoter

In this study, Cu and Co doped Ni/Al₂O₃ nanocatalyst was synthesized via impregnation and sol–gel methods. The physiochemical properties of nanocatalyst were characterized by XRD, field emission scanning electron microscopy (FESEM), particle size distribution, BET, fourier transform infrared spectroscopy (FTIR), TG–DTA and energy dispersive X-ray (EDX) analysis. The samples were employed for CO₂-reforming of methane in atmospheric pressure, temperature range from 550 to 850 °C, under various mixture of CH₄/CO₂ and different gas hourly space velocity. XRD patterns besides indicating the decline of the peaks intensity in sol–gel method, proved the potential of this procedure in diminishing the crystal size and preventing the NiAl₂O₄ spinel formation. Moreover, high surface area might derive of smaller particle size and uniform morphology of sol–gel prepared ones, confirmed by FESEM and BET analysis. TG–DTG analysis as well supported the higher surface area for sol–gel made ones, represented the proper calcination temperature (approximately 600 °C). Also, presence of the active phases and elemental composition of nanocatalysts determine via EDX analysis. Promoting the basicity and the adsorption rate of CO₂, is attributed to the higher amount of OH groups for sol–gel prepared samples, proved by FTIR. Ni–Co/Al₂O₃ due to the synergetic effect of sol–gel method and cobalt addition depicted excellent characterization such as higher surface area, smaller particle size, supplying more stable support and enhanced morphology. Therefore, this nanocatalyst represented the best products yield (H₂ = 98.21 and CO = 95.64), H₂/CO close to unit (0.92–1.05) and stable conversion during 1,440 min stability test. So, Ni–Co/Al₂O₃ among all of the prepared nanocatalysts demonstrated the best catalytic performance and presented it as a highly efficient catalyst for dry reforming of methane. Despite of the stable yield of Ni–Cu/Al₂O₃, it depicted the lower catalytic activity and H₂/CO ratio than the unprompted nanocatalysts.     

Sol–gel preparation of mesoporous Al2O3–SiO2 glasses: structural evolution monitored by solid state NMR

Glasses along the composition line 0.5Al₂O₃–xSiO₂ (1 ≤ x ≤ 6) were prepared via a novel sol–gel route using tetraethylorthosilicate and aluminum lactate as precursors. The structural evolution from solution to gel to glass is monitored by standard ²⁷Al and ²⁹Si nuclear magnetic resonance (NMR) spectroscopies, revealing important insights about molecular level mechanisms occurring at the various stages of glass formation. Under the experimental conditions reported, silica and alumina precursors undergo homoatomic condensation processes when the gel is heat treated at about 100 and 300 °C, respectively, and only little heteroatomic co-condensation occurs in this temperature range. The latter is promoted only upon elimination of the residual lactate and water ligands upon annealing the gels above 300 °C. Following calcination at 650 °C, mesoporous glasses are obtained, having average pore diameter of about 3 nm and a surface areas near 500 m²/g. Si–O–Al connectivities are detected by ²⁹Si magic angle spinning (MAS)-NMR. ²⁷Al MAS-NMR spectra reveal aluminum in four-, five- and six-coordination. The spectra differ significantly from those of other sol–gel derived Al₂O₃–SiO₂ materials prepared from different precursor routes, suggesting that the lactate route results in a higher degree of compositional homogeneity.     

Li‐doped nanosized TiO2 powder with enhanced photocalatylic acivity under sunlight irradiation

This work reports on the synthesis of Li‐doped TiO₂ nanoparticles using the sol–gel process and solid‐state sintering, and investigates their potential use as a photocatalyst for degradation under sunlight excitation of different organic model compounds in aqueous solution. The structure of the nanocrystals was examined by X‐ray diffraction, UV‐vis ground state diffuse reflectance absorption spectra and X‐ray photoelectron emission spectroscopy. Results showed that samples prepared by sol–gel process and calcined at 400 °C are composed of a mixture of anatase and rutile phases, in contrast to the one prepared by solid‐state sintering, which exhibits an anatase phase with Li being involved in a spinel phase. The photocatalytic degradation of aqueous solutions of different aromatic compounds was successfully achieved under sunlight excitation in presence of Li‐doped TiO₂ prepared via sol–gel process. It was shown that the calcination temperature and the preparation mode greatly affect the photocatalytic efficiency. Copyright © 2010 John Wiley & Sons, Ltd.     

Combination of radical and cationic photoprocesses for the single‐step synthesis of organic‐inorganic hybrid films

Nanocomposite materials prepared from radically photocurable hybrid sol–gel precursors have been widely developed within the last decade, especially to devise novel optical devices and coatings. For their synthesis, a preferential route has involved in the successive sol–gel process of acrylate trialkoxysilane precursors followed by radical photopolymerization. In contrast, this work presents an original one‐step synthesis based on the association of two different photoinitiators (PIs) in the same formulation: the photolysis of a hydroxyphenylketone (radical PI) affords polyacrylate chains while that of a diaryl iodonium salt (cationic PI) generates powerful superacids catalyzing the sol–gel reactions of the alkoxy functions. The behavior of methacrylate and acrylate trimethoxysilane precursors was compared to highlight the effect of the organic moiety functionality on the reaction kinetics (Fourier transform infrared spectroscopy) and the film microstructure (¹³C and ²⁹Si solid‐state nuclear magnetic resonance). Interestingly, evidence of local organization in these hybrid films was also given by X‐ray analysis. In a last part, their thermomechanical properties were discussed thoroughly using a range of techniques: DSC, scratch‐resistance test, nanoindentation. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 4150–4158, 2010     

Pentamethylcyclopentadienylrhodium(I) complexes incorporated into porous polysiloxanes prepared by a sol–gel process: catalysts for hydrogenation of crotonic acid in water

Pentamethylcyclopentadiene‐functionalized polysiloxanes were prepared by a sol–gel process from tetraethoxysilane and (pentamethylcyclopentadienylmethyl)methyldiethoxysilane without a catalyst. The polysiloxanes are microporous–mesoporous solids, of which the BET surface areas and micropore volumes are inversely proportional to the concentration of the functionalizing agent (5–21 mol%) in the starting mixture of alkoxysilanes. The polysiloxanes were also characterized by CP MAS ¹³C NMR spectroscopy, revealing essentially the same structure of organofunctional ligand as that in particulate materials with low surface areas prepared earlier in a sol–gel process catalyzed by dibutyltin diacetate. Novel alkoxysilyl‐substituted pentamethylcyclopentadienyl (1,5‐cyclo‐octadiene)rhodium(I) complexes were synthesized from the corresponding cyclopentadienes by deprotonation followed by reaction with [(cod)RhCl]₂ (cod = cyclo‐octadiene). Polysiloxane‐bound rhodium complexes were prepared by a sol–gel reaction analogous to the one mentioned above and were found to catalyze the hydrogenation of crotonic acid in water; to the best of our knowledge, this constitutes the first example of catalysis by a well‐defined polysiloxane‐bound transition metal complex in an aqueous system. Copyright © 2000 John Wiley & Sons, Ltd.     

Non‐surfactant template‐directed synthesis of SiO2‐polyimide hybrid self‐standing films with ordered mesoporous structure

The silica‐PI hybrid self‐standing films with ordered mesoporous structure have been prepared by using dibenzoyl‐L ‐tartaric acid (L ‐DBTA) as non‐surfactant template under mild sol–gel route. Polyimide matrix was obtained from polyamic acid (PAA) via thermal imidization process and the template was removed in this process. The PI‐based hybrid film with 20 wt% SiO₂ obtained from DBTA presented the ordered mesoporous channels with average pore size of about 2.0 nm and BET surface area of 1167 m²/g. FTIR and SEM studies indicated that the hydrogen bond interaction between the carboxylic groups of DBTA and benzamide bonds of PAA made the PAA possibly participate in the assembly process of the aggregates of the non‐surfactant template molecules. The mechanical, thermal and some physical properties of these hybrid films materials were also characterized. Copyright © 2010 John Wiley & Sons, Ltd.     

The optimization of silica gel synthesis from chemical bottle waste using response surface methodology

To reduce the amount of hazardous chemical bottle waste in the environment, we report the optimization research of silica extraction in chemical bottle waste into silica gel. Alkali fusion and sol–gel process were utilised to prepare silica gel effectively. The alkali fusion process was carried out by adding sodium hydroxide to produce sodium silicate. Afterwards, silica gel was prepared by the sol–gel method using hydrochloric acid. Box-Behnken Design (BBD) was applied to Optimisation factors the poptimiseactors affecting the silica recovery. The factors that optimised mass ratio, particle size, and temperature. The optimum recovery of silica gel was obtained by SiO₂: NaOH mass ratio of 1:3, the particle size of 63–74 µm, and a temperature of 800 °C. The purity of silica gel optimum is 63.74% characterised using X-ray fluorescence. The structure of silica gel is the appearance of amorphous peaks at 2θ 20-30° characterised using an x-ray diffractogram. The silica gel surface was characterises using scanning electron microscopy-energy dispersive x-ray. It showed an irregular surface and characteristic showed that silica gel had a radius of 15.74 nm and a specific surface area of 297.08 m².     

Cu-Ni-Al尖晶石催化甲醇水蒸气重整制氢性能的研究

以氢氧化铜、醋酸镍和拟薄水铝石为原料,通过固相法合成了Cu-Ni-Al尖晶石催化剂。采用N2物理吸附、XRD、H2-TPR和XPS等表征方法,研究Cu/Ni/Al的物质的量比和焙烧温度对催化剂的比表面积、物相、还原性能以及表面性质的影响,并以甲醇水蒸气重整制氢为探针反应,考察催化剂的缓释催化性能。结果表明,随着焙烧温度的升高,Cu-Ni-Al催化剂的尖晶石含量增加,但尖晶石晶粒增大,且比表面积下降。不同的焙烧温度和Cu/Ni/Al物质的量比,所得催化剂的比表面积、还原性能和表面性质不同,从而表现出不同的缓释催化性能。与计量比Cu/Al=1∶2的合成比较,Cu/Al=1∶3形成了非计量比的富Al尖晶石固溶体,生成的晶体粒子小、比表面积和孔容大、难还原的尖晶石部分增多,呈现出更好的缓释催化性能。甲醇制氢反应性能评价结果显示,Cu-Ni-Al尖晶石在反应条件下逐渐释放活性铜而催化反应的进行,其中,CNA3-1000催化剂表现中最高的催化活性和稳定性。