Investigation on lithium ion conductivity and structural stability of yttrium-substituted Li<Subscript>7</Subscript>La<Subscript>3</Subscript>Zr<Subscript>2</Subscript>O<Subscript>12</Subscript>

Advanced Li-air battery architecture demands a high Li⁺ conductive solid electrolyte membrane that is electrochemically stable against metallic lithium and aqueous electrolyte. In this work, an investigation has been carried out on the microstructure, Li⁺ conduction behaviour and structural stability of Li₇La_3-x Y _x Zr₂O₁₂ (x = 0.125, 0.25 and 0.50) prepared by conventional solid-state reaction technique. The phase analysis of Li₇La_3-x Y _x Zr₂O₁₂ (x = 0.125, 0.25 and 0.50) sintered at 1200 °C by powder X-ray diffraction (PXRD) and Raman confirms the formation of high Li⁺ conductive cubic phase (\( Ia\overline{3}d \)) lithium garnets. Among the investigated lithium garnets, Li₇La_2.75Y_0.25Zr₂O₁₂ sintered at 1200 °C exhibits a maximized room temperature total (bulk + grain boundary) Li⁺ conductivity of 3.21 × 10^?4 S cm^?1 along with improved relative density of 96 %. The preliminary investigation on the structural stability of Li₇La_2.75Y_0.25Zr₂O₁₂ in the solutions of 1 M LiCl, dist. H₂O and 1 M LiOH at 30 °C/50 °C indicates that the Li₇La_2.75Y_0.25Zr₂O₁₂ is relatively stable against 1 M LiCl and dist. H₂O. Further electrochemical investigation is essential for practical application of Li₇La_2.75Y_0.25Zr₂O₁₂ as protective solid electrolyte membrane in aqueous Li-air battery.     

Substitution effects on the bulk and surface properties of (Li,Ni)Mn<Subscript>2</Subscript>O<Subscript>4</Subscript>

Manganese oxides of spinel structure, LiMn₂O₄, Li_1-x Ni _x Mn₂O₄ (0.25 ≤ x≤ 0.75), and NiMn₂O₄, were studied by EDS, XRD, SEM, magnetic (M-H, M-T), and XPS measurements. The samples were synthesized by an ultrasound-assisted sol-gel method. EDS analysis showed good agreement with the formulations of the oxides. XRD and Rietveld refinement of X-ray data indicate that all samples crystallize in the Fd3m space group characteristic of the cubic spinel structure. The a-cell parameter ranges from a = 8.2276 Å (x = 0) to a = 8.3980 Å (x = 1). SEM results showed particle agglomerates ranging in size from 2.3 μm (x = 0) down to 0.8 μm (x = 1). Hysteresis magnetization vs. applied field curves in the 5–300K range was recorded. ZFC-FC measurements indicate the presence of two magnetic paramagnetic-ferrimagnetic transitions. The experimental Curie constant was found to vary from 5 to 7.1 cm³ K mol^?1 for the range of compositions studied (0 ≤ x ≤ 1). XPS studies of these oxides revealed the presence of Ni²⁺, Mn³⁺, and Mn⁴⁺. The experimental Ni/Mn atomic ratios obtained by XPS were in good agreement with the nominal values. A linear relationship of the average oxidation state of Mn with Ni content was observed. The oxide’s cation distributions as a function of Ni content from x = 0 ?Li⁺[Mn³⁺Mn⁴⁺]O₄ to x = 1 \( {\mathrm{Ni}}_{0.35}^{2+}{\mathrm{Mn}}_{0.65}^{3+}\left[{\mathrm{Ni}}_{0.65}^{2+}\right.\left.{\mathrm{Mn}}_{1.35}^{3+}\right]{\mathrm{O}}_4 \) were proposed.     

Magnetic M<Subscript><Emphasis Type="Italic">x</Emphasis></Subscript>O<Subscript><Emphasis Type="Italic">y</Emphasis></Subscript>@N-C as heterogeneous catalysts for the catalytic oxidation of aniline solution with sulfate radicals

Metal nanoparticles have been combined with magnet metal–organic frameworks (MOFs) to afford new materials that demonstrate an efficient catalytic degradation, high stability, and excellent reusability in areas of catalysis because of their exceptionally high surface areas and structural diversity. Magnetic M _x O _y @N-C (M = Fe, Co, Mn) nanocrystals were formed on nitrogen-doped carbon surface by using 8-hydroxyquinoline as a C/N precursor. The Co@N-C, MnO@N-C, and Fe/Fe₂O₃@N-C catalysts were characterized by X-ray diffraction (XRD), Raman, scanning electron microscopy (SEM), high-resolution transmission electron microscopy (HRTEM), N₂ adsorption/desorption, and X-ray photoelectron spectroscopy (XPS). The catalytic performances of catalysts were thoroughly investigated in the oxidation of aniline solution based on sulfate radicals (SO₄ ^?.) toward Fenton-like reaction. Magnetic M _x O _y @N-C exhibits an unexpectedly high catalytic activity in the degradation of aniline in water. A high magnetic M _x O _y @N-C catalytic activity was observed after the evaluation by aniline degradation in water. Aniline degradation was found to follow the first-order kinetics, and as a result, various metals significantly affected the structures and performances of the catalysts, and their catalytic activity followed the order of Co > Mn > Fe. The nanoparticles displayed good magnetic separation under the magnetic field.

Open image in new window

Graphical Abstract ?

     

Structure,ionic conduction,and phase transformations in lithium titanate Li<Subscript>4</Subscript>Ti<Subscript>5</Subscript>O<Subscript>12</Subscript>

The spinel structure of lithium titanate Li₄Ti₅O₁₂ is refined by the Rietveld full-profile analysis with the use of x-ray and neutron powder diffraction data. The distribution and coordinates of atoms are determined. The Li₄Ti₅O₁₂ compound is studied at high temperatures by differential scanning calorimetry and Raman spectroscopy. The electrical conductivity is measured in the high-temperature range. It is shown that the Li₄Ti₅O₁₂ compound with a spinel structure undergoes two successive order-disorder phase transitions due to different distributions of lithium atoms and cation vacancies (□, V) in a defect structure of the NaCl type: (Li)_8a[Li_0.33Ti_1.67]_16dO₄ → [Li□]_16c[Li_1.33Ti_1.67]_16dO₄ → [Li_1.33□_0.67]_16c[Ti_1.67□_0.33]_16dO₄. The low-temperature diffusion of lithium predominantly occurs either through the mechanism ... → Li(8a) → V(16c) → V(8a) → ... in the spinel phase or through the mechanism ... → Li(16c) → V(8a) → V(16c) → ... in an intermediate phase. In the high-temperature phase, the lithium cations also migrate over 48f vacancies: ... Li(16c) → V(8a, 48f) → V(16c) → ....     

The magnetization reversal in CoFe<Subscript>2</Subscript>O<Subscript>4</Subscript>/CoFe<Subscript>2</Subscript> granular systems

The temperature-dependent field cooling (FC) and zero-field cooling (ZFC) magnetizations, i.e., M _FC and M _ZFC, measured under different magnetic fields from 500 Oe to 20 kOe have been investigated on two exchange–spring CoFe₂O₄/CoFe₂ composites with different relative content of CoFe₂. Two samples exhibit different magnetization reversal behaviors. With decreasing temperature, a progressive freezing of the moments in two composites occurs at a field-dependent irreversible temperature T _irr. For the sample with less CoFe₂, the curves of ?d(M _FC ? M _ZFC)/dT versus temperature T exhibit a broad peak at an intermediate temperature T ₂ below T _irr , and the moments are suggested not to fully freeze till the lowest measuring temperature 10 K. However, for the ?d(M _FC ? M _ZFC)/dT curves of the sample with more CoFe₂, besides a broad peat at an intermediate temperature T ₂, a rapid rise around the low temperature T ₁~15 K is observed, below which the moments are suggested to fully freeze. Increase of magnetic field from 2 kOe leads to the shift of T ₂ and T _irr towards a lower temperature, and the shift of T ₂ is attributable to the moment reversal of CoFe₂O₄.

Open image in new window

Graphical abstract CoFe₂O₄/CoFe₂ composites with different relative content of CoFe₂ were prepared by reducing CoFe₂O₄ in H₂ for 4 h (S4H) and 8 h (S8H). The temperature-dependent FC and ZFC magnetizations, i.e., M _FC and M _ZFC, under different magnetic fields from 500 Oe to 20 kOe have been investigated. Two samples exhibit different magnetization reversal behaviors. With decreasing temperature, a progressive freezing of the moments in two composites occurs at field-dependent irreversible temperature T _irr. For the S4H sample, the curves of ?d(M _FC ? M _ZFC)/dT versus temperature T exhibit a broad and field-dependent relaxing peak at T ₂ below T _irr (figure a), and the moments were suggested not to fully freeze till the lowest measuring temperature 10 K. However, for the S8H sample, it exhibits the reentrant spin-glass state around 50 K, as evidenced by a peak in the M _FC curve (inset in figure b) and as a result of the cooperative effects of the random anisotropy of CoFe₂O₄, exchange–spring occurring at the interface of CoFe₂O₄ and CoFe₂ together with the inter-particle dipolar interaction (figure c); in ?d(M _FC ? M _ZFC)/dT curves, besides a broad relaxing peat at T ₂, a rapid rise around the low-temperature T ₁~15 K is observed, below which the moments are suggested to fully freeze. Increase of magnetic field from 2 kOe leads to the shift of T ₂ and T _irr towards a lower temperature, and the shift of T ₂ is attributable to the moment reversal of CoFe₂O₄.

     

Electrospun Dy-doped SrFe<Subscript>12</Subscript>O<Subscript>19</Subscript> nanofibers: microstructure and magnetic properties

SrDy _x Fe_12?x O₁₉ (x ≤ 0.08) nanofibers have been synthesized by the electrospinning method followed by calcinations process. The partial substitution of rare earth ions Dy³⁺ (10.5 μ _B of magnetic moments) mainly occupying 12k sublattice sites in the SrFe₁₂O₁₉ crystal structure is investigated and discussed in this work. An enhanced coercivity of 7155 Oe has been obtained when the doped content reached to 0.08 at a relative low calcination temperature of 800 °C. As a result, we believe the synthesized SrDy _x Fe_12?x O₁₉ nanofibers can potentially be useful in high-density recording media as well as permanent magnets.     

Comparative study of solid-state reaction and sol-gel process for synthesis of Zr-doped Li<Subscript>0.5</Subscript>La<Subscript>0.5</Subscript>TiO<Subscript>3</Subscript> solid electrolytes

We investigated the synergistic influences of synthesis methods (solid-state reaction vs. sol-gel process) and Zr⁴⁺ doping on the structure and ionic conductivity of perovskite-structured Li_0.5La_0.5TiO₃ (LLTO) solid electrolytes. The lithium-ion conductivity of Li_0.5La_0.5Ti_1???x Zr _x O₃ ceramic specimens was evaluated as a function of x value and compared carefully between those two synthesis methods. Regarding the conductivity, sol-gel process is better for the synthesis of LLTO than solid-state reaction. As a result, the highest grain conductivity is obtained in the sol-gel-derived pure LLTO sample with x?=?0, reaching 1.10?×?10^?3 S?·?cm^?1. Partial substitution of Zr⁴⁺ enlarges the LLTO’s grain aggregate size and increases the total superficial area of aggregates. Consequently, Zr⁴⁺ substitution not only affects the grain (bulk) conductivity, but more importantly, also improves the grain boundary conductivity and the total conductivity. The highest total conductivity is 5.84?×?10^?5 S?·?cm^?1 with x?=?0.04 by sol-gel process.     

High-frequency EPR of Cr<Superscript>2+</Superscript> ions in CdGa<Subscript>2</Subscript>S<Subscript>4</Subscript>

High-frequency broad-band (65–240 GHz) EPR is used to study impurity centers of bivalent chromium in a CdGa₂S₄ crystal. It is found that the EPR spectra correspond to tetragonal symmetry. The spin Hamiltonian H = βB · g · S + B ₂ ⁰ O ₂ ⁰ + B ₄ ⁰ O ₄ ⁰ + B ₄ ⁴ O ₄ ⁴ with the parameters B ₂ ⁰ =23659±2 MHz, B ₄ ⁰ =1.9±1 MHz, |B ₄ ⁴ |=54.2±2 MHz, g_‖=1.93±0.02, and g_⊥=1.99±0.02 is used to describe the observed spectra. It is concluded that chromium ions occupy one of the tetrahedrally coordinated cation positions.     

Preparation and characterization of Sm<Superscript>3+</Superscript>-doped SrSnO<Subscript>3</Subscript> and its photoelectric performance as photo-anode of dye-sensitized solar cells

Sm³⁺-doped SrSnO₃ (SrSnO₃:Sm³⁺) nanopowders were synthesized by a simple hydrothermal method and followed by a heat treatment process. The as-synthesized nanopowders were assembled in dye-sensitized solar cells (DSSCs) to investigate their photoelectric properties. X-ray diffraction (XRD), scanning electron microscope (SEM), and energy-dispersive spectrometer (EDS) confirmed the formation of SrSnO₃:Sm³⁺ nanopowders with perovskite structure. The ultraviolet-visible absorption spectra and photoluminescence spectra indicate a down-conversion from ultraviolet light to visible light which matches the strong absorption region of the N719 dye. The DSSC based on SrSnO₃:Sm³⁺ photo-anode improved its photoelectric conversion efficiency (η) via the down-conversion of doped Sm³⁺. Under the irradiation of the simulated sunlight with 100 mW/cm², the DSSC based on SrSnO₃ doping with Sm³⁺ of 0.6 wt% showed the highest η of 1.54%, which improved 71.11% compared with the DSSC based on pure SrSnO₃.

Open image in new window

Graphical abstract Excitation and emission spectrums of SrSnO₃ with different Sm³⁺ doping amounts.

     

Conductivity and spectroscopic studies of Li<Subscript>2</Subscript>O-V<Subscript>2</Subscript>O<Subscript>5</Subscript>-B<Subscript>2</Subscript>O<Subscript>3</Subscript> glasses

Lithium vanadium-borate glasses with the composition of 0.3Li₂O–(0.7-x)B₂O₃–xV₂O₅ (x?=?0.3, 0.325, 0.35, 0.375, 0.4, 0.425, 0.45, and 0.475) were prepared by melt-quenching method. According to differential scanning calorimetry data, vanadium oxide acts as both glass former and glass modifier, since the thermal stability of glasses decreases with an increase in V₂O₅ concentration. Fourier transform infrared spectroscopy data show that the vibrations of [VO₄] structural units occur at V₂O₅ concentration of 45 mol%. It is established that the concentration of V⁴⁺ ions increases exponentially with the growth of vanadium oxide concentration. Direct and alternative current measurements are carried out to estimate the contribution both electronic and ionic conductivities to the value of total conductivity. It is shown that the electronic conductivity is predominant in the total one. The glass having the composition of 0.3Li₂O-0.275B₂O₃-0.475V₂O₅ shows the highest electrical conductivity that has the value of 7.4?×?10^?5 S cm^?1 at room temperature.     

Properties of Ca-containing LiCoPO<Subscript>4</Subscript>-graphitic carbon foam composites

LiCo_1???x Ca _x PO₄–graphitic carbon foam composites are prepared using a sol–gel method. The structural analysis reveals LiCoPO₄ as major crystalline phase and Co₂P₂O₇ (for x?=?0.0) and Co₂P, Li₃PO₄, and (Ca,Co)₃(PO₄)₂ (for x?≥?0.05) as secondary phases. The morphology consists of microcrystalline “islands” with acicular crystallites (5–50 μm size). Transmission electron microscopy (TEM) of the powders showed that the Ca is incorporated into the crystal structure evoking exaggerated grain growth. The voltammetric profiles show a decrease of the voltammetric surface between anodic and cathodic sweeps and a shift of the reduction potentials toward higher values (～4.6 V, x?=?0.1). The electrochemical measurements, at a discharge rate of C/10 (room temperature), show an increase of the discharge-specific capacity from 100 mAhg^?1 for x?=?0.0 to 104 mAhg^?1 for x?=?0.1. The ac impedance spectroscopy data revealed an improvement of the Li-ion conductivity at high content of Ca ions (x?=?0.1).     

Investigation of the structural and electrochemical performance of Li<Subscript>1.2</Subscript>Ni<Subscript>0.2</Subscript>Mn<Subscript>0.6</Subscript>O<Subscript>2</Subscript> with Cr doping

Cr-doped layered oxides Li[Li_0.2Ni_0.2???x Mn_0.6???x Cr_2x ]O₂ (x?=?0, 0.02, 0.04, 0.06) were synthesized by co-precipitation and high-temperature solid-state reaction. The materials were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), high-resolution transmission electron microscopy (TRTEM), X-ray photoelectron spectroscopy (XPS), and electrochemical impedance spectroscopy (EIS). XRD patterns and HRTEM results indicate that the pristine and Cr-doped Li_1.2Ni_0.2Mn_0.6O₂ show the layered phase. The Li_1.2Ni_0.16Mn_0.56Cr_0.08O₂ shows the best electrochemical properties. The first discharge specific capacity of Li_1.2Ni_0.16Mn_0.56Cr_0.08O₂ is 249.6 mA h g^?1 at 0.1 C, while that of Li_1.2Ni_0.2Mn_0.6O₂ is 230.4 mA h g^?1. The capacity retaining ratio of Li_1.2Ni_0.16Mn_0.56Cr_0.08O₂ is 97.9% compared with 93.9% for Li_1.2Ni_0.2Mn_0.6O₂ after 80 cycles at 0.2 C. The discharge capacity of Li_1.2Ni_0.16Mn_0.56Cr_0.08O₂ is 126.2 mA h g^?1 at 5.0 C, while that of the pristine Li_1.2Ni_0.2Mn_0.6O₂ is about 94.5 mA h g^?1. XPS results show that the content of Mn³⁺ in the Li_1.2Ni_0.2Mn_0.6O₂ can be restrained after Cr doping during the cycling, which results in restraining formation of spinel-like structure and better midpoint voltages. The lithium-ion diffusion coefficient and electronic conductivity of Li_1.2Ni_0.2Mn_0.6O₂ are enhanced after Cr doping, which is responsible for the improved rate performance of Li_1.2Ni_0.16Mn_0.56Cr_0.08O₂.     

Dielectric and AC conductivity studies in Li<Subscript>2</Subscript>O-CoO-B<Subscript>2</Subscript>O<Subscript>3</Subscript>-TeO<Subscript>2</Subscript> glasses

CoO and Li₂O mixed with borotellurite glasses in the compositions, (B₂O₃)_0.2-(TeO₂)_0.3-(CoO) _x -(Li₂O)_0.5?x, where x = 0.05, 0.10, 0.15, 0.20, 0.25, 0.30, 0.35, 0.40, 0.45, and 0.50 were synthesized by fast cooling the melt to room temperature. Absence of crystalline phases in the samples was confirmed by X-ray diffraction studies. Changes in dielectric properties with frequency and temperature over wide ranges have been measured. Dielectric constant and loss increased with increase in CoO content. AC conductivity has been analyzed using Mott’s small polaron model and activation energy was determined. Activation energy decreased and conductivity increased with increase in CoO content up to 0.3 mole fractions, and they behaved oppositely for higher concentration of CoO. This observed change of trend in activation energy and conductivity at 0.3 mole fraction of CoO ascribed to switch over of conduction mechanism occurring from predominantly ionic to electronic regime. For the first time, a transition of conduction mechanism is observed in borotellurite glasses. Temperature and composition independent relaxation mechanism in these glasses has been confirmed by plotting the scaled conductivity master curves. Hunt’s model has been invoked to understand the frequency dispersion of conductivity.

Open image in new window

Graphical abstract Plots of ln(ε′′) versus ln(F) for BTCL2 glass at different temperatures

     

Research of the Spin-Hamiltonian Parameters and Defect Structure for the Trigonal Mn<Superscript>4+</Superscript> Centers in Y<Subscript>2</Subscript>Ti<Subscript>2</Subscript>O<Subscript>7</Subscript>:Mn<Superscript>4+</Superscript> Crystal

The high-order perturbation formulas founded on the two-mechanism model are applied in this paper to compute the spin-Hamiltonian parameters (g factors g _//, g _⊥ and zero-field splitting D) of the trigonal Mn⁴⁺ centers in Y₂Ti₂O₇:Mn⁴⁺ crystal. In this model, besides the contributions from the traditional crystal-field (CF) mechanism (in the CF theory) related to CF excited states, those from the charge-transfer (CT) mechanism connected with CT excited states are contained. The calculated results are reasonably coincident with the observed values. The calculations show that the contributions of CT mechanism to spin-Hamiltonian parameters (in particular, the g factors) for (MnO₆)^8? clusters are large and cannot be neglected. The defect structure of trigonal (MnO₆)^8? clusters in Y₂Ti₂O₇:Mn⁴⁺ crystals is also evaluated. The results are discussed.     

Weak ferromagnetism in BiFeO<Subscript>3</Subscript>-based multiferroics

The magnetic properties of the Bi_{1 ? x} Ln _x FeO₃ (Ln is a rare-earth ion), Bi_{1 ? x} A _x FeO_{3 ? x/2} (A is an alkali earth ion), and BiFe_{1 ? x} Ti _x O_{3 + δ} solid solutions in magnetic fields up to 14 T have been studied. The concentration ranges of the existence of the ferroelectric phase described by the space group R3c have been determined. It is shown that the substitution of the rare-earth ions for the Bi³⁺ ions leads to a sharp decrease in the critical fields inducing the metamagnetic transition from a modulated antiferromagnetic state to a weakly ferromagnetic one; however, the modulated structure in the concentration range of the R3c phase is mainly retained. The substitution of the alkali earth ions (x ～ 0.1) for the bismuth ions leads to the total destruction of the modulated structure and to the implementation of the weakly ferromagnetic state within the R3c phase. A homogeneous weakly ferromagnetic state has been revealed when the Ti⁴⁺ ions (x = 0.1) are substituted for the Fe³⁺ ions in the ferroelectric R3c phase.     

Structural and magnetic phase transformations in the BiFeO<Subscript>3</Subscript>-CaFe<Subscript>0.5</Subscript>Nb<Subscript>0.5</Subscript>O<Subscript>3</Subscript> system

The crystal structure and magnetic properties of the Bi_{1 ? x} Ca _x Fe_{1 ? x/2}Nb _x/2O₃ system were studied. It is shown that, at x ≤ 0.15, the unit-cell symmetry of solid solutions is rhombohedral (space group R3c). Solid solutions with x ≥ 0.3 have an orthorhombic unit cell (space group Pbnm). The rhombohedral compositions are antiferromagnetic, while the orthorhombic compositions exhibit a small spontaneous magnetization due to Dzyaloshinski?-Moriya interaction. In CaFe_0.5Nb_0.5O₃, the Fe³⁺ and Nb⁵⁺ ions are partially ordered and the unit cell is monoclinic (space group P2₁/n). In the concentration range 0.15 < x < 0.30, a two-phase state (R3c + Pbnm) is revealed.     

Oxygen isotope effect in chromium-doped Pr<Subscript>0.5</Subscript>Ca<Subscript>0.5</Subscript>MnO<Subscript>3</Subscript> manganites

The effect of oxygen isotope substitution on the properties of Pr_0.5Ca_0.5Mn_{1 ? x} Cr _x O₃ manganites (x = 0, 0.02, 0.05) have been studied. The introduction of chromium favors (i) the decomposition of a charge-ordered state and (ii) the appearance of a ferromagnetic metallic phase in Pr_0.5Ca_0.5Mn_{1 ? x} Cr _x ^16–18O₃. The isotope substitution ¹⁶O → ¹⁸O leads to a decrease in the content of the ferromagnetic phase, an increase in the charge-ordering transition temperature (T _CO), and a decrease in the ferromagnetic transition temperature (T _FM). The isotope mass exponent is evaluated.     

Facial synthesis of carbon-coated ZnFe<Subscript>2</Subscript>O<Subscript>4</Subscript>/graphene and their enhanced lithium storage properties

Carbon-coated ZnFe₂O₄ spheres with sizes of ~110–180 nm anchored on graphene nanosheets (ZF@C/G) are successfully prepared and applied as anode materials for lithium ion batteries (LIBs). The obtained ZF@C/G presents an initial discharge capacity of 1235 mAh g^?1 and maintains a reversible capacity of 775 mAh g^?1 after 150 cycles at a current density of 500 mA g^?1. After being tested at 2 A g^?1 for 700 cycles, the capacity still retains 617 mAh g^?1. The enhanced electrochemical performances can be attributed to the synergetic role of graphene and uniform carbon coating (~3–6 nm), which can inhibit the volume expansion, prevent the pulverization/aggregation upon prolonged cycling, and facilitate the electron transfer between carbon-coated ZnFe₂O₄ spheres. The electrochemical results suggest that the synthesized ZF@C/G nanostructures are promising electrode materials for high-performance lithium ion batteries.

Open image in new window

Graphical abstract ?

     

Effect of Ce-doped MnO<Subscript>2</Subscript> catalyst on the lithium-air batteryperformance in the ambient atmosphere

MnO₂ doped with Ce was hydrothermally synthesized and the as-made breathable waterproof membrane used outside the cathode was prepared for improving the lithium-air battery performance in air. The samples were characterized by scanning electron microscopy (SEM), energy dispersive spectrum analysis (EDS), charge–discharge cycle tests, charge–discharge cycle tests of limited capacity, and electrochemical impedance spectroscopy (EIS) tests. The result showed that Ce _x Mn_1-x O₂ can effectively reduce the charge overpotential of the cathode. The charge and discharge electrical potential difference of Ce_0.1Mn_0.9O₂ was only 700 mV while MnO₂’s was 2100 mV. And Ce_0.1Mn_0.9O₂ that exhibited high discharge capacity of 400 mAh g^?1 in air had a stable discharge platform of 2.5 V and then the more obvious charge phenomenon appeared after 3.5 V. The excellent catalysis, the effect of cathode catalytic materials named Ce _x Mn_1-x O₂, may attribute to the decrease of reaction potential energy of oxygen reduction reaction and oxygen evolution reaction.     

Nuclear spin resonance of <Superscript>53</Superscript>Cr in ferromagnetic CuCr<Subscript>2</Subscript>S<Subscript>4</Subscript>: Sb

The influence of variable valence on NSR spectra of ⁵³Cr nuclei in ferromagnetic CuCr_2?xSb_xS₄ (x = 0, 0.02, 0.07) at T = 77 K is considered. For quadrupole nuclei in locally anisotropic positions, the effects of variable valence result in averaging of not only the resonance frequency but also of the quadrupole and magnetic anisotropy constants. The significant difference between the experimental and calculated values of these constants indicates the important role of the intrinsic electronic contribution to the anisotropy of hyperfine fields of compounds containing Cr⁴⁺ ions. Additional lines caused by intrinsic and induced defects in the structure are observed in the spectra of doped and undoped compounds.